Lutron Electronics 0025 STRD-7B Transceiver (Keypad) User Manual 043 146a

Download:
Mirror Download [FCC.gov]
Document ID	341993
Application ID	nvIvbosNIaucrEdQ+C+Ccg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.81kB (572633 bits)
Date Submitted	2003-07-22 00:00:00
Date Available	2003-07-22 00:00:00
Creation Date	2003-05-27 08:59:35
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2003-07-03 09:39:02
Document Title	043-146a.qxd
Document Creator	PScript5.dll Version 5.2
Document Author:	rlau

Installation Instructions
Please Read Before Installing
Overview
The STRD-1B, -2B, -3B,
-3BRL, -4B, -4FS, -4S, -4SIR,
-5B, -5FS, -5BRL, -6B, -6BRL,
and -7B keypads are for use
with HomeWorks systems.
The keypad buttons are programmed with a personal
computer using the
HomeWorks Utility.
Up to 32 keypads, each with a
unique address, can be
assigned to each HomeWorks
RF Processor.
Designer-style RF seeTouchTM
Keypads
Installation
STRD-1B, -2B, -3B, -3BRL, -4B, -4FS, -4S,
-4SIR, -5B, -5FS, -5BRL, -6B, -6BRL, -7B
120 V ~, 50/60 Hz, 0.2 A
1. Turn power OFF at fusebox or circuit breaker.
STRD-1B*
STRD-4B*
STRD-2B*
STRD-4FS*
STRD-3B*
STRD-4S*
STRD-3BRL*
STRD-4SIR*
4. Push all wires back into the wallbox and loosely fasten the
control to the wallbox using the keypad mounting screws provided. Do not pinch the wires.
Danger - Locate and remove fuse or lock circuit breaker
in the OFF position before proceeding. Wiring with
power ON may result in personal injury.
2. Prepare wires. When making wire connections, follow the
recommended strip lengths and combinations for the supplied wire connectors. Note: Wire connectors provided are
suitable for copper wire only.
Small:
STRD-5B*
STRD-5FS*
STRD-5BRL*
STRD-6B*
Strip insulation 3/8 in. (10 mm) for
14 AWG (2.5 mm2).
Strip insulation 1/2 in. (13 mm) for
16 AWG (1.5 mm2).
Use to join one 14 AWG supply wire with one 16
or 18 AWG (1.0 mm2) control wire.
5. Attach Lutron Claro or Satin Colors wallplate adapter and
wallplate.
a. Loosely install keypad mounting screws.
c. Tighten keypad mounting screws until wallplate
adapter is flush to wall (do not over-tighten).
d. Snap wallplate onto wallplate adapter, and verify that
buttons are not submerged.
6. Restore power.
Symptom
Cause and Action
LEDs don't light up when buttons are
pressed.
Power not present at keypad
• Circuit breaker OFF. Turn ON breaker.
• Wiring error. Check wiring to be sure it
agrees with installation instructions.
Button presses on keypad cause the keypad to quickly flash all its LEDs simultaneously.
Keypad has not been addressed.
Button presses on keypad cause the keypad to slowly flash all its LEDs simultaneously.
Keypad has an address, but has not had
programming uploaded.
Keypad cannot be addressed.
Keypad is out of RF communications range.
• Address the keypads using the
HomeWorks Utility.
• Upload to the system using the
HomeWorks Utility.
• Move RF Signal Repeater or RF
Processor to within 30 feet (9 m) of keypad.
LEDs light when button is pressed, but the
system response is not correct.
3. Wiring: See Wiring Diagram.
STRD-6BRL*
RF Keypads will not function until they are addressed and programmed using the HomeWorks Utility.
b. Tighten wallplate adapter mounting screws snug.
e. If buttons are submerged, loosen keypad mounting
screws appropriately.
Small
Troubleshooting Guide
Improper programming
• Check programming in HomeWorks
Utility.
STRD-7B*
* Wallplate/Adapter
purchased separately.
Important Notes
Codes: Install in accordance with all local and national electrical codes.
Environment: Ambient operating temperature:
0-40°C, 32-104°F, 0-90% humidity, non-condensing. Indoor use
only.
Technical and Sales Assistance
Mounting Diagram
Wallplates: Lutron Claro® and Satin ColorsTM wallplates are recommended for best color match and clean aesthetic appearance. Do not paint controls or wallplates.
If you need assistance, call the toll-free Lutron
Technical Support Center. Please provide exact
model number when calling.
(800) 523-9466 (U.S.A., Canada and the Caribbean)
Other countries call:
Tel:
(610) 282-3800
Fax:
(610) 282-3090
Visit our Web site at www.lutron.com
Wiring Diagram
Keypad
Mounting
Screws
Button
Kit
Adapter
Mounting
Screws
Hot/Live
Black
FCC Information
Cleaning: To clean, wipe with a clean damp cloth. DO NOT
use any chemical cleaning solutions.
Wallboxes: Lutron recommends using 3-1/2 in. (89 mm) deep
wallboxes for easier installation.
RF Device Placement: RF Keypads must be located within 30
ft. (9 m) of an RF Signal Repeater or an RF Processor.
RF Keypads will not function until they are addressed and programmed using the HomeWorks Utility.
120/127 VAC
50/60 Hz
White
Wallbox
Neutral
Keypad
Wallplate/Adapter purchased
separately.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in the U.S.A. 02/03 P/N 043-146 Rev. A
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the seperation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to
operate this equipment.
LIMITED WARRANTY
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within two years after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone the Lutron
Technical Support Center toll free at 800-523-9466. After the two year period, a pro-rated warranty applies to this product until eight years after
the purchase. For more information regarding this warranty contact your Lutron representative.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION,
DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
These products may be covered under one or more of the following U.S. patents: 4,835,343; 4,889,999; 5,170,068; 5,237,207; 5,736,965;
5,838,226; 5,848,054; 5,905,442; 5,982,103; D436,930; D453,742; D456,783; D461,782; D465,460; D465,770; D466,090; D466,091; D466,484
and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro and HomeWorks are registered trademarks and Satin
Colors, seeTouch and the HomeWorks Logo are trademarks of Lutron Electronics Co., Inc.
© 2003 Lutron Electronics Co., Inc.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:05:27 08:59:35-04:00
Modify Date                     : 2003:07:03 09:39:02-04:00
Page Count                      : 1
Creation Date                   : 2003:05:27 08:59:35-04:00
Mod Date                        : 2003:07:03 09:39:02-04:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : rlau
Metadata Date                   : 2003:07:03 09:39:02-04:00
Creator                         : rlau
Title                           : 043-146a.qxd

EXIF Metadata provided by EXIF.tools