Lutron Electronics 0030 Control Unit User Manual 031 xxxa RadioTouch addendum
Lutron Electronics Company Inc Control Unit 031 xxxa RadioTouch addendum
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 395179 |
| Application ID | phtKxE5QcXwZa3LNI/OkTQ== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 19.87kB (248378 bits) |
| Date Submitted | 2004-02-09 00:00:00 |
| Date Available | 2004-02-06 00:00:00 |
| Creation Date | 2003-12-16 09:28:15 |
| Producing Software | Acrobat Distiller 4.0 for Macintosh |
| Document Lastmod | 2003-12-16 09:28:30 |
| Document Title | 031-xxxa RadioTouch addendum |
| Document Creator | QuarkXPress(tm) 4.1 |
| Document Author: | Rob's mac |
Attention Contractors... RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® Coopersburg, PA 18036 STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper. See Installers Guide for System Addressing and Programming Instructions 1 2 3 Closure Com Sw Closure 5 Sw Closure 4 Sw Closure 3 Sw Closure 2 0-10 Gray Sw Closure 1 9 10 11 12 13 14 15 16 Sivoia Cntrl 2 Circuit Com Power Status Program 0-10 V Shade Occ. Sensor 0-10 Purple 6 7 Sivoia Cntrl 1 24V 15V PS Signal Signal Occ. Com Terminal connections are Class 2. 1 2 1 2 3 4 5 Burn-in Button Shade Settings 1 2 3 4 5 Switch Closures 1 2 3 10 11 12 CLASS 2 LOW VOLTAGE WIRING © 2000-2002 Lutron Electronics Co., Inc. Powered Status Program When Lit Indicator Button Receiver Settings Burn-In 13 14 15 16 Installer’s Guide Addendum for Tabletop Transmitters A Step-by-Step Guide for Installing, and Operating Tabletop Transmitters for use with a Lutron RadioTouchTM Visual Environment Control System Hardware Installation RadioTouch Addressing a Tabletop Transmitter Each column of buttons on the tabletop transmitter must be addressed to the Controller that you wish to control with that column. Addressing Columns of Buttons Step A - Press and release the programming button on the Controller. After the button is pressed the lights will cycle up and down for 3 seconds to notify you that you are in programming mode, and settle at 50% light output. If you are using an RTA-RX-SW the lights will cycle OFF and ON. The Status LED will be in fast blink mode. RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® Coopersburg, PA 18036 Status LED STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON Step B - While in programming mode press the corresponding button in the column that you want to control the receiver and hold for 5 seconds (see Transmitter diagrams below). The Controller will flash or cycle the lights OFF and ON when the transmitter is added. If no lights are being controlled by the receiver, you will not get visual feedback. Step C - Press the programming button again to exit from programming mode. The lights will go to high end and the Status LED will return to slow blink mode. If you are using an RTA-RX-SW the lights will cycle OFF and ON. To test the tabletop transmitter for lights, press any button in the column added on the tabletop transmitter and verify that the lights respond. For Sivoia® shades, press any button and see that the shades move. If no response return to step A and be sure to hold the buttons for 5 seconds while in step B. Step D - Repeat steps A through C for each column you need to address to a Controller. Press and hold this button SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper. See Installers Guide for System Addressing and Programming Instructions 1 2 3 Closure Com Sw Closure 5 Sw Closure 4 Sw Closure 3 0-10 Gray Sw Closure 2 Sw Closure 1 24V Power Status Program 9 10 11 12 13 14 15 16 0-10 V Shade Occ. Sensor Sivoia Cntrl 1 6 7 Sivoia Cntrl 2 0-10 Purple 15V Circuit Com Signal PS Signal Occ. Com Terminal connections are Class 2. 1 2 1 2 3 4 5 Burn-in Button Shade Settings 1 2 3 4 5 Switch Closures 1 2 3 10 11 12 CLASS 2 LOW VOLTAGE WIRING © 2000-2002 Lutron Electronics Co., Inc. Powered Status Program When Lit Indicator Button Receiver Settings Programming button Burn-In 13 14 15 16 Dimmable Lights Non-dim Lights Step A & C Press and hold this button Two button Switch Closure Three button Switch Closure Press and hold this button Four button Switch Closure Step B - Columns of buttons RadioTouch Tabletop Transmitter Addendum Five button Switch Closure Hardware Installation RadioTouch Deleting a Tabletop Transmitter Each column of buttons on the tabletop transmitter must be deleted separately from the Controller that you no longer wish to control. Deleting Columns of Lights Step A - Press and release the programming button on the Controller. After the button is pressed the lights will cycle up and down for 3 seconds to notify you that you are in programming mode, and settle at 50% light output. If you are using an RTA-RX-SW the lights will cycle OFF and ON. The Status LED will be in fast blink mode. RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® Coopersburg, PA 18036 Status LED STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON Step B - While in programming mode press the corresponding buttons in the column that you want to delete from the Controller and hold for 5 seconds (see Transmitter diagrams below). The Controller will flash the lights when the transmitter is deleted. If no lights are being controlled by the Controller, you will not get visual feedback. Step C - Press the programming button again to exit from programming mode. The lights will go to high end or turn ON, and the Status LED will return to slow blink mode. To test the Tabletop Transmitter press any button on the transmitter in the column that has been deleted and verify that the lights or shades do not respond. Step D - Repeat for each row you need to delete from a Controller. Press and hold this button SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper. See Installers Guide for System Addressing and Programming Instructions 1 2 3 0-10 V Shade Occ. Sensor Power Status Program Closure Com Sw Closure 4 Sw Closure 5 Sw Closure 3 Sw Closure 2 Sw Closure 1 9 10 11 12 13 14 15 16 Sivoia Cntrl 2 Sivoia Cntrl 1 24V 6 7 0-10 Gray 15V 0-10 Purple Signal PS Signal Circuit Com Occ. Com Terminal connections are Class 2. 1 2 1 2 3 4 5 Burn-in Button Shade Settings 1 2 3 4 5 Switch Closures 1 2 3 10 11 12 CLASS 2 LOW VOLTAGE WIRING © 2000-2002 Lutron Electronics Co., Inc. Powered Status Program When Lit Indicator Button Receiver Settings Programming button Burn-In 13 14 15 16 Dimmable Lights Non-dim Lights Step A & C Press and hold these buttons Two button Switch Closure Three button Switch Closure Press and hold these buttons Four button Switch Closure Five button Switch Closure Step B - Columns of buttons RadioTouch Tabletop Transmitter Addendum Hardware Installation RadioTouch Setting the ON light level of a two button, dimmable lighting column Remote Method Note: No DIP switches need to be switched to perform this operation. Step A - Press and hold the ON and the lower buttons for 5 seconds. The lights will flash to notify you that you are in Preset Adjust Mode, and settle at 100% light level. Step B - Using the raise/lower buttons in that column on the transmitter controlling the Controller that you are adjusting, set the lights at the new ON level. Step C - Press and hold the ON and raise buttons for 5 seconds. The lights will flash to notify you that the ON level has changed. Step D - Press and hold the ON and the lower buttons for 5 seconds to exit Preset Adjust Mode. The lights will flash and return to their maximum light level. Test the ON button to make sure the light level is correct. If not, repeat steps A through D. Notes: • The Controller will not react to preset button presses from any transmitter while the Controller is in Preset Adjust Mode. • Preset light levels may be affected by a photosensor input. As ambient light increases / decreases the preset light levels will scale accordingly. Press and hold these two buttons for 5 seconds Press and hold these two buttons for 5 seconds Step A & D Step C Setting the ON light level of a two button, dimmable lighting column DIP Switch Method Step C - Press and hold the ON and raise buttons for 5 seconds. The lights will flash to notify you that the ON level has changed. Step D - Flip DIP switch #1 back up to exit Preset Adjust Mode. Notes: • The Controller will not react to preset button presses from the transmitter while the Controller DIP switch #1 is flipped to the down position. • Preset light levels may be affected by a photosensor input. As ambient light increases / decreases the preset light levels will scale accordingly. Step A - Flip DIP switch #1 down on the Controller. After the switch is flipped the Controller will be in Preset Adjust Mode. (If a photosensor is connected to this Controller your lights may change level when DIP switch #1 is flipped.) Step B - Using the raise/lower buttons on the transmitter controlling the Controller that you are adjusting, set the lights at the new ON level. RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® Coopersburg, PA 18036 STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper. See Installers Guide for System Addressing and Programming Instructions 1 2 3 0-10 V Shade Occ. Sensor Power Status Program 1 2 3 4 5 Closure Com Sw Closure 5 Sw Closure 3 Sw Closure 4 Sw Closure 2 Sw Closure 1 9 10 11 12 13 14 15 16 Sivoia Cntrl 1 Sivoia Cntrl 2 24V 15V 6 7 0-10 Gray Signal PS Signal 0-10 Purple Circuit Com Occ. Com Terminal connections are Class 2. 1 2 Burn-in Button Shade Settings 1 2 3 4 5 Switch Closures 1 2 3 10 11 12 CLASS 2 LOW VOLTAGE WIRING © 2000-2002 Lutron Electronics Co., Inc. Powered Status Program When Lit Indicator Button Receiver Settings Flip DIP switch #1 to the down position Burn-In 13 14 15 16 Step A & D Press and hold these two buttons for 5 seconds RadioTouch Tabletop Transmitter Addendum Step C Hardware Installation RadioTouch RadioTouch RTA-RX-F-SC TM Radio Frequency Controller LISTED 243C Ind. Cont. Eq. ® STATUS INDICATOR OPERATION ON - Burn-in Mode Slow Blink -Normal Operation Mode Fast Blink - Program Mode Very Fast Blink - Receiving RF Data RECEIVER SWITCH SETTINGS 1. UP-Preset Lock DN.-Preset Adj. 2. UP-Occ. Sensor DN.-Emerg. Set. 3. UP-FDB Mode DN.-ECO Mode 4. UP-OFF DN.-Min. Light 5. UP-Auto ON DN.-Manual ON SHADE SWITCH SETTINGS 1. UP-A/C Shades DN.-Normal Oper. See Installers Guide for System Addressing and Programming Instructions 1 2 3 Power Status Program Closure Com Sw Closure 5 Sw Closure 4 Sw Closure 3 Sw Closure 2 0-10 Gray Sw Closure 1 9 10 11 12 13 14 15 16 0-10 V Shade Occ. Sensor Sivoia Cntrl 1 24V 6 7 0-10 Purple 15V PS Signal Circuit Com Signal Occ. Com 1 2 1 2 3 4 5 Burn-in Button Shade Settings 1 2 3 4 5 Switch Closures 1 2 3 10 11 12 CLASS 2 LOW VOLTAGE WIRING © 2000-2002 Lutron Electronics Co., Inc. Powered Status Program When Lit Indicator Button Receiver Settings Terminal connections are Class 2. The RadioTouch controller has the ability to provide 5 momentary dry output switch closures. These closures can be used to operate AC shades, Motorized Projection Screens, or other equipment designed to accept momentary dry switch closures. A column of 5 buttons on a Tabletop Transmitter correspond to Switch Closures 1 through 5 on the Controller. A two button column on a Tabletop Transmitter will activate Switch Closures 2 and 4. A three button column on a Tabletop Transmitter will activate Switch Closures 2, 4, and 3, in that order. (See diagrams below.) The switch closure outputs on the RadioTouch Controller provide a momentary dry closure for 0.250 seconds to other equipment. The closure terminals are shown below. Coopersburg, PA 18036 Sivoia Cntrl 2 Wiring output switch closures to other equipment (RTA-RX-F-SC only) Burn-In 13 14 15 16 Switch Closure Common Switch Closure 5 Switch Closure 4 Switch Closure 3 Switch Closure 2 Switch Closure 1 Switch Closure Outputs – Not to exceed 30VDC and 1/3 Amp. Tabletop Button Functions Closure 2 Closure 2 Closure 4 Closure 4 Closure 3 Two and Three button Switch Closures Closure 1 Closure 2 Closure 3 Closure 4 Closure 5 Five button Switch Closures RadioTouch Tabletop Transmitter Addendum Hardware Installation RadioTouch Setup for AC Motorized Window Treatments (RTA-RX-F-SC only) Make sure that the RadioTouch Controller is properly wired. Refer to the RadioTouch Installer’s Guide (P/N 030-200) for detailed wiring information. Step A - On the RadioTouch Controller, flip SHADE SETTINGS DIP SWITCH #1 UP for open, close, and stop functionality. Step B - Make sure appropriate transmitters are added to the Controller. See page 2 for Addressing Tabletop Transmitters to Controllers. Setup for AC Motorized Projection Screens (RTA-RX-F-SC only) Make sure that the RadioTouch Controller is properly wired. Refer to the RadioTouch Installer’s Guide (P/N 030-200) for detailed wiring information. Step A - On the RadioTouch Controller, flip SHADE SETTINGS DIP SWITCH #1 DOWN for up and down functionality. Step B - Make sure appropriate transmitters are added to the Controller. See page 2 for Addressing Tabletop Transmitters to Controllers. RadioTouch Tabletop Transmitter Addendum Tabletop Button Functions Open Stop Close Three button Switch Closure Tabletop Button Functions Up Down Two button Switch Closure Notes RadioTouch Tabletop Transmitter Addendum LIMITED WARRANTY Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply to you. These products may be covered by one of more of the following U.S. patents: 4,663,570; 4,751,399; 4,783,581; 4,835,343; 4,894,587; 5,001,386; 5,041,763; 5,055,742; 5,142,199; 5,144,205; 5,173,643; 5,224,029; 5,248,919; 5,281,961; 5,293,097; 5,309,068; 5,357,170; 5,399,940; 5,555,150; 5,633,540; 5,637,930; 5,736,965; 5,798,581; 5,838,226; 5,841,239; 5,848,054; 5,864,212; 5,905,442; 5,942,727; 5,962,979; 5,982,103; 6,111,368; 6,313,588; 6,346,781; RE37,135; 6,225,760; DES 353,798; DES 364,141; DES 378,814; DES 389,461; DES 389,805; DES 395,037; DES 404,013; DES 422,969; DES 428,855; DES 436,579; DES 439,220; and corresponding foreign patents. Other U.S. and foreign patents may be pending. Lutron, is a registered trademark and RadioTouch is a trademark of Lutron Electronics Co., Inc. World Headquarters Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 U.S.A. TOLL FREE: (800) 523-9466 (U.S.A., Canada, and the Caribbean) Tel: (610) 282-3800; International 1610 282-3800 Fax: (610) 282-3090; International 1610 282-3090 European Headquarters Lutron EA LTD Lutron House 6 Sovereign Close Wapping London, E1 9HW England FREEPHONE: 0800 282107 (U.K.) Tel: (0171) 702-0657; International 44-171-702-0657 Fax: (0171) 480-6899; International 44-171-480-6899 Japan Sales Office Lutron Asuka Co., Ltd No. 16 Kowa Bldg. 4F 1-9-20 Akasaka, Minato-ku Tokyo 107-0052 Japan TOLL FREE: (0120) 083417 (Japan) Tel: (03) 5575-8411; International 81-3-5575-8411 Fax: (03) 5575-8420; International 81-3-5575-8420 Hong Kong Sales Office Tel: 2104-7733; International 852-2104-7733 Fax: 2104-7633; International 852-2104-7633 Technical and Sales Assistance If you have questions concerning the installation or operation of this product, call the toll-free Lutron Technical Support Center. Please provide exact model number when calling. U.S.A., Canada, and the Caribbean (800) 523-9466 27 hrs/7 days other countries (610) 282-3800 8:00a.m. – 8:00p.m. ET Our address on the web is http://www.lutron.com © 2003 Lutron Electronics Co., Inc. MADE AND PRINTED IN U.S.A. P/N 031-xxx Rev. A 12/03 Lutron Electronics Co., Inc., reserves the right to make improvements or changes in its products without prior notice. Although every attempt is made to ensure that this information is accurate and up to date, please check with Lutron to confirm product availability, latest specifications and suitability for your application.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 2003:12:16 09:28:15 Producer : Acrobat Distiller 4.0 for Macintosh Author : Rob's mac Title : 031-xxxa RadioTouch addendum Creator : QuarkXPress(tm) 4.1 Modify Date : 2003:12:16 09:28:30-05:00 Page Count : 8EXIF Metadata provided by EXIF.tools