Lutron Electronics 0039 Wireless Roller 64 for HomeWorks User Manual master

Download:
Mirror Download [FCC.gov]
Document ID	659799
Application ID	X1nt1ez4ziUlOy+F/NlISQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	70.25kB (878184 bits)
Date Submitted	2006-05-18 00:00:00
Date Available	2006-05-18 00:00:00
Creation Date	2006-04-23 23:30:47
Producing Software	QuarkXPress(tm) 6.1
Document Lastmod	2006-04-23 23:33:12
Document Title	master
Document Creator	QuarkXPress(tm) 6.1

Sivoia QED™
Wireless Roller 64™
for HomeWorks®
Installation
Instructions
Sivoia QED
TM
| Wireless Roller 64 for HomeWorks
Installation Instructions
Tools Required:
Tape Measure
Wire Cutter/Stripper
Pliers
#2 Phillips Screwdriver
1/4” Hex-Head Driver
Level
Power Drill
Notes:
1)
2)
For Wireless Roller 64 programming refer to the HomeWorks® Illumination Online Help.
The Electronic Drive Unit (EDU) will need to be powered to complete installation.
Wireless Shades will not function until they are addressed and programmed using the
HomeWorks® Illumination Software.
Box Contents:
Sivoia QED™ Wireless Roller 64
(2) Bracket Leveling Spacer (2) Cable Tie Anchor
Standard Mounting Brackets
with Retaining Screws
(1) 3 Pin Terminal Block
(5) Mounting Screws
(#8x1-3/4" (#8x44mm) Hex Head Screws)
(2) 4” (102mm) Cable Ties
(Actual Size)
(1) Programming Stylus
SIVOIA QED Wireless Roller 64 Installation Instructions 1
TM
(1) Screwdriver
(2) Antenna
Mounting Clips
Sivoia QED
TM
| Wireless Roller 64 for HomeWorks
Installation Instructions (continued)
Warning: Incorrect installation can lead to severe injury, follow all installation instructions.
Notes:
• The Sivoia QED Wireless Roller 64 must be used only with window treatments approved by Lutron.
• There must be a clearance of at least 1.3 feet (0.4 meters) between the fully lowered system
and any permanent object.
• Installation shall be executed by a qualified electrician according to national wiring rules.
• Before shade installation, remove any unnecessary cords and disable any equipment not
needed for powered operation. The Sivoia QED Wireless Roller 64 has a maximum rated operating
time of 8 min. out of 20.
• Codes: Install in accordance with all local and national electrical codes.
• Environment: Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing.
Indoor use only.
SIVOIA QED Wireless Roller 64 Installation Instructions 2
TM
Sivoia QED
TM
| Wireless Roller 64 for HomeWorks
Installation Instructions (continued)
• RF Device Placement: Wireless shades must be located within 30 feet (9m) of an RF Signal
Repeater or an RF Processor. The distance between repeater and processor must be less than
60 feet (18m).
Wireless shades will not function until they are addressed and programmed. See the HomeWorks
Illumination Software Online Help.
Wireless shades are programmed with a personal computer using the HomeWorks
Illumination Software.
30 feet (9m)
30 feet (9m)
SIVOIA QED Wireless Roller 64 Installation Instructions 3
TM
1
Confirm System Dimensions
Package Label
1.1
Compare system dimensions on
the package label with the window
dimensions to verify appropriate
window/shade combination.
System Width
System Width
System Height
(Bracket to Bracket Width)
SIVOIA QED Wireless Roller 64 Installation Instructions 4
TM
System Height
2
Position the Mounting Brackets
2.1
Mark the location of the mounting brackets so that they are centered over the window.
Note: Bracket to Bracket distance = Fabric Width + 1.5” (38 mm) = System Width.
Note: For ceiling and jamb mount, allow clearance to prevent fabric from rubbing against trim, window,
top treatment, etc.
Note: Wall mount may require blocks (not provided) to clear trim.
(System Width)
SIVOIA QED Wireless Roller 64 Installation Instructions 5
TM
3
Install the Mounting Brackets
3.1
Install the first mounting bracket.
3.2
Install the second mounting bracket.
Note: Put a screw in the center of each slot. Use slots as needed to
ensure brackets are level and plumb as positioned.
SIVOIA QED Wireless Roller 64 Installation Instructions 6
TM
4
Pre-drill for Cable Run
DANGER - Locate and lock breaker to the shade power supply in the OFF position
or unplug the power plug-in transformer before doing any wiring.
4.1
Wall Mount
Choose one of the options below to drill for cable access.
Note: Cable should exit from wall, ceiling, or jamb on EDU side of system.
Note: Leave 12-18” (30-45 cm) of cable exposed.
Wall Mount with wires through:
A) Wall: 1” in from end of system and .5” from top of bracket
B) Ceiling: .5” in from end of system and .5” from mounting wall
C) Jamb: 1” from top of bracket and .5” from mounting wall
Wall Mount
SIVOIA QED Wireless Roller 64 Installation Instructions 7
TM
4
4.2
Pre-drill for Cable Run: (continued)
Ceiling Mount
Ceiling Mount with wires through:
A) Wall: 1” in from end of system and .5” from ceiling
B) Ceiling: 1” in from end of system and .5” from back of bracket
C) Jamb: 1” from back of bracket and .5” from ceiling
Ceiling Mount
SIVOIA QED Wireless Roller 64 Installation Instructions 8
TM
4
4.3
Pre-drill for Cable Run: (continued)
Jamb Mount
Jamb Mount with wires through:
A) Wall: .5” from ceiling and .5” from outside of jamb
B) Ceiling: .5” from wall and .5” from outside of jamb
C) Jamb: .5” from ceiling and .5” from wall
Jamb Mount
SIVOIA QED Wireless Roller 64 Installation Instructions 9
TM
5
Wire 3-Pin Terminal Block
5.1
Strip 2” of jacket
off cable run from
the wall.
5.2
Wire 3-Pin terminal block (provided) to cable using the included screwdriver.
EGND (Pin 3)
24 VAC (Pin 2)
24 VAC (Pin 1)
SIVOIA QED Wireless Roller 64 Installation Instructions 10
TM
To EDU
Connector
6
Orient the Buttons and Wiring
6.1
For the following bracket and button orientations, route the wires as shown.
Note: The buttons should be accessible when the shade is installed
Note: The wires may go in either or both of the indicated slots
tio
rec
rD
he
Eit
SIVOIA QED Wireless Roller 64 Installation Instructions 11
TM
on
Directi
Either
on
Directi
Either
Buttons
tio
rec
rD
he
Eit
7
Mount the Shade
7.1
Install the idler side of the shade onto its bracket.
7.2
Depress the spring loaded idler by pressing the shade towards the idler, and install the EDU
side of the shade onto its bracket.
SIVOIA QED Wireless Roller 64 Installation Instructions 12
TM
8
Adjust the Shade
8.1
Ensure that the shade is level and centered.
8.2
Adjust shade by removing the necessary screws and moving the brackets as needed, or
installing bracket leveling spacers.
Note: You may have to remove the shade to access the bracket screws.
8.3
Reinstall and tighten the screws.
SIVOIA QED Wireless Roller 64 Installation Instructions 13
TM
9
Secure the Antenna
9.1
For optimal performance secure the antenna in 1 of 3 configurations shown below using
the antenna clips provided.
WARNING: - The antenna is covered with a clean Plastic sleeve to protect it. Do not
cut the antenna or remove the plastic sleeve. Do not modify the antenna.
Antenna mounted parrallel with shade
use these configurations. When Pocket
or Fascia is not used.
Antenna mounted straight down.
Antenna clipped to bottom of Pocket or Fascia - This configuration provides optimal performance with
metal Fascia.
Note: Lutron has tested this product with the antenna mounted in the configurations above
and found that these provide optimal performance.
SIVOIA QED Wireless Roller 64 Installation Instructions 14
TM
10
Connect Terminal Blocks
10.1
Plug 7-pin terminal block on cable into EDU terminal block attached to shade bracket
(a cable tie can be used to secure the terminal blocks together).
10.2
Dress wires to ensure fabric does not rub while the shade is moving.
WARNING: Do not cut wires coming out of shade. Doing so will damage the antenna.
10.3
Copy the serial number located on every shade’s harness and shade location on page 21 of this
manual. This will ease addressing and programming later on the installation.
SIVOIA QED Wireless Roller 64 Installation Instructions 15
TM
11
Secure and Check the Shade
11.1
Tighten retaining screws in each bracket to secure the shade.
SIVOIA QED Wireless Roller 64 Installation Instructions 16
TM
11.2 Secure and Check the Shade (continued)
Reconnect power to the shade power supply.
Use the programming stylus to run the shade up and down using the adjustment
buttons (
), re-level if needed.
Observe: Pay careful attention to the shade roll up to ensure that it does not telescope
extremely to one side or the other.
Tip: Slight telescoping is normal. However, if the shade is telescoping severely to one
side and it is level, press the “Close Limit Button” ( ), and lower the shade all the way
down using the adjustment buttons (
). Place a piece of tape on the side of the tube
that the fabric is telescoping away from when finished press the “Close Limit Button” ( )
once. This technique is referred to as “SHIMMING”. The shade will always track towards
the side that the tape (shim) is placed on.
SIVOIA QED Wireless Roller 64 Installation Instructions 17
TM
12
Setting Limits from the EDU
Setting the Open Limit from the EDU
Note: Setting the Open Limit lower than the Close Limit will cause the shade to move down
when raise is pressed and up when lower is pressed.
12.1
Tap the “Open Limit Button”
( ), the green LED on the
roller shade EDU will turn on
steady, indicating that the EDU
is in “Set Open Limit Mode.”
12.2
Adjust the position of the
EDU to the desired Open
Limit using the adjustment
buttons ( ).
12.3
Press and hold the “Open
Limit Button” ( ) for 5
seconds. The green LED on
the roller shade EDU will
flash for 2 seconds, then go
dark, indicating that the
current position has been
stored as the Open Limit.
SIVOIA QED Wireless Roller 64 Installation Instructions 18
TM
12
Setting Limits from the EDU (continued)
Setting the Close Limit from the EDU
12.4
Tap the “Close Limit
Button” ( ). The green
LED on the roller Shade
EDU will turn on steady,
indicating that the EDU is
in “Set Close Limit Mode”.
12.5
Adjust the position of the
EDU to the desired Close
Limit using the adjustment
buttons (
).
12.6
Press and hold the “Close
Limit Button” ( ) for 5
seconds. The green LED on
the roller shade EDU will
flash for 2 seconds, then go
dark, indicating that the
current position has been
stored as the Close Limit.
SIVOIA QED Wireless Roller 64 Installation Instructions 19
TM
13
Finish System Programming
The Sivoia QED shade is now installed, wired, and the OPEN/CLOSE limits for each shade have
been set.
The next step is to finish programming the system, using the HomeWorks Illumination Software.
SIVOIA QED Wireless Roller 64 Installation Instructions 20
TM
14
Troubleshooting
Symptom
Shade will not move using
adjustment buttons on EDU...
Solution
...EDU is not powered - check EDU Power.
By unplugging and re-plugging in EDU.
LED should light for 5 seconds.
...Shade is caught on something - free shade.
...Shade is not programmed to keypad or event.
Shade does not fully open or fully close...
...Limits have been set incorrectly - refer to “set
open limit” and “set close limit” sections on re-set
limits using HW1 Software.
...Shade fabric is caught on something - free shade.
...Check that brackets are mounted level.
...Check that fabric is tracking correctly on
the shade tube.
...Check that brackets are centered.
Fabric not level...
Fabric not centered over window...
Shade does not move smoothly...
...Check for binding of shade fabric on side
channels.
...Check fabric tracking.
Wireless Shade can not be addressed.... ...Shade is out of RF communications range.
Move RF signal repeater or RF processor to
within 30 feet (9m) of shade.
SIVOIA QED Wireless Roller 64 Installation Instructions 21
TM
Location
Shade
Serial
Number
Shade
33
34
35
36
37
38
39
40
41
10
42
11
43
12
44
13
45
14
46
15
47
16
48
17
49
18
50
19
51
20
52
21
53
22
54
23
55
24
56
25
57
26
58
27
59
28
60
29
61
30
62
31
63
32
64
SIVOIA QED Wireless Roller 64 Installation Instructions 22
TM
Location
Serial
Number
Technical Assistance
WORLD
HEADQUARTERS
CUSTOMER SERVICE
/E-MAIL
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036
United States
Tel: +1-610-282-3800
Fax:+1-610-282-1243
shadinginfo@lutron.com
CUSTOMER
SERVICE/ORDERING
INTERNET:
TECHNICAL SUPPORT
& SERVICES
USA +1-800-523-9466 –
24 hours/7 days
www.lutron.com
USA +1-888-LUTRON1
08.00 - 20.00 EST
Limited Warranty
Lutron offers an 8-year limited warranty for our
shading systems. Please contact customer
service or visit our website for a complete
warranty statement.
Lutron reserves the right to make improvements or changes to these products without
prior notice. Although every attempt is made to
ensure that this information is accurate and up
to date, please check with Lutron to confirm
product availability, the latest specifications,
and suitability for your application.
These products may be covered by one or
more of the following US patents:
5,983,783
and corresponding foreign patents.
US and foreign patents pending.
Lutron, the Sunburst logo, and Sivoia are
registered trademarks, and Sivoia QED is a
trademark of Lutron Electronics Co., Inc.
©2006 LUTRON Electronics Co., Inc.
Printed in the U.S.A.
P/N 045-119 REV. A
FCC Information
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the
equipment and receiver.
•
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced
radio/TV technician for help.
Caution: Changes or modifications not
expressly approved by Lutron Electronics Co.
could void the user's authority to operate
this equipment.
Industry Canada
Information
The term “IC” before the radio
certification number only signifies that
Industry Canada technical specifications
were met.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 24
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0f1f390c-d343-11da-a87b-001124e220c8
Producer                        : QuarkXPress(tm) 6.1
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (50% Grey.spot).%%CMYKCustomColor: .427 .31 .282 .125 (50% Grey.spot).%%EndComments
Create Date                     : 2006:04:23 23:30:47Z
Creator Tool                    : QuarkXPress(tm) 6.1
Modify Date                     : 2006:04:23 23:33:12-04:00
Metadata Date                   : 2006:04:23 23:33:12-04:00
Document ID                     : uuid:f6a7034e-d342-11da-a87b-001124e220c8
Format                          : application/pdf
Title                           : master
Creator                         : QuarkXPress(tm) 6.1

EXIF Metadata provided by EXIF.tools