Lutron Electronics 0056 Electronic dimmer with RF communication User Manual
Lutron Electronics Company Inc Electronic dimmer with RF communication
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 979331 |
| Application ID | eomDDHvx8MxZO7LaMRoIuA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 26.1kB (326307 bits) |
| Date Submitted | 2008-07-31 00:00:00 |
| Date Available | 2008-07-31 00:00:00 |
| Creation Date | 2008-06-25 11:51:53 |
| Producing Software | Adobe PDF Library 7.0 |
| Document Lastmod | 2008-06-25 11:53:55 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS2 (4.0.5) |
StanzaTM StanzaTM Lamp Socket Dimmer/Switch SZ-1SD-TP Installation Instructions 120 V Please Read Before Installing 50 / 60 Hz Installation Operation The lamp socket dimmer/switch may be installed in any orientation between vertical and 90° from vertical. When installed in any orientation other than vertical, derating is required. Dimming knob Lamp Socket Dimmer/Switch Load Specifications Control SZ-1SD Load Type Min. Load Max. Load Incandescent 10 W 150 W Halogen 10 W 100 W Orientation Compact fluorescent 10 W 30 W Vertical Important Notes Install in accordance with all local and national electrical codes. Environment: Ambient operating temperature: 32 to 104 °F (0 to 40 °C), 0 to 90% humidity, non-condensing. Indoor use only. Cleaning: To clean, wipe with a clean damp cloth. Do not use any chemical cleaning solutions. RF Device Placement: RF dimmers and switches must be located within 20 feet (6 m) of an RF signal repeater or a device configured as a repeater. Stanza RF dimmers or switches cannot be controlled by the system until they are addressed and programmed. They will work as stand-alone controls only. Range and performance of the Stanza system are dependent on a variety of factors, including: •D istance between system components •G eometry of the space •C onstruction of walls separating system •E lectrical equipment located near the system components •P osition of the lamp socket dimmer/ switch. Lamp requirements: Do not use dimmer to control table lamps with touch control or with integral dimmers. Lamps without integral switches are recommended; lamps with integral switches must be set to full on, then the switch should be disabled or removed. Derating Chart 10 to 90° from vertical Load Type Rating Incandescent 150 W Halogen 100 W Incandescent 100 W Halogen 75 W 1. F ind a suitable location for the lamp socket dimmer/switch. The dimmer/ switch must be within 20 feet (6 m) of a device configured as a repeater. If there is a switch on the lamp, make sure it is in the full on position, and remove or disable it if possible. 2. U nplug the lamp cord from the wall receptacle. 3. R emove the lamp Remove harp. lamp harp. 4. R emove the lamp bulb, and screw the lamp socket Install lamp dimmer/ socket. switch into the lamp socket. Replace the bulb into the lamp socket dimmer/switch. 5. R einstall the lamp harp (rotate it to clear the lamp socket dimmer/switch if necessary). If desired, install the optional harp lock using the provided hex wrench. Status indicator Dimming Knob •T urn clockwise to turn on and brighten •T urn counter-clockwise to dim and turn off •P ush in to toggle on and off •P ush in and hold to enter programming mode •A udible sound indicates when high and low levels are reached Status Indicator • Indicates current load status •G reen = load is switched on •O ff = load is switched off •A mber = device is in programming mode •R ed = device is experiencing an overtemperature condition Operation Notes •T he lamp socket dimmer/switch should immediately control the bulb once power is applied. •W hen initially installed, the lamp socket dimmer/switch functions only as a switch, which allows it to control non-dimmable compact fluorescent bulbs. To also dim incandescent loads, it must first be addressed as part of a Stanza system. •T he lamp socket dimmer/switch cannot be controlled over radio frequency (RF) from a keypad or contact closure input until it has been addressed as part of a Stanza system. Troubleshooting Guide Symptom Cause and Action Light does not turn on, but the status indicator is on. Light bulb/lamp is burned out or not installed. • Replace or install lamps. Light does not turn on, and the status indicator is off. Power is off • Check the circuit breaker and make sure it is on. Lamp is unplugged • Check that the lamp cord is plugged into the wall socket. Lamp has an integral switch • Make sure the lamp’s integral switch is set to full on. Dimmer does not dim properly and/or flickers. Tighten harp lock. Caution! To avoid risk of electrical shock, do not attempt to open the lamp socket dimmer / switch. Unplug the table lamp before changing the light bulb. 6. P lug the lamp cord into the wall socket. Returning the Dimmer/Switch to Factory Settings 1. Triple-tap the dimming knob quickly (within 1 second). 2. Press and hold the dimming knob for 5 seconds (until the load flashes). 3. Triple-tap the dimming knob quickly again. Notes •R eturning to factory settings will clear all programming from the lamp socket dimmer/switch device, and will prevent it from being controlled over RF from a keypad or control interface. •A fter being returned to factory defaults, the device will need to be readdressed as part of a system. •T he device will revert to switching operation, so non-dimmed compact fluorescent loads can be controlled. Incandescent loads then cannot be controlled until the device has been re-addressed as part of a system. Otherwise, damage to the device or bulb may occur. Lamp has an integral dimmer • Use a lamp without a dimmer. Bulb is not dimmable • Replace bulb with incandescent bulb. Technical support: U SA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 Central/South America: +1.610.282.6701 Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with 8-year pro-rated parts replacement on commissioned systems. FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may not cause harmul interference, and (2) this device must accept any interference received, incouding interference that may cause undesired operation. These products may be covered under one or more of the following U.S. patents: 5,248,919; 5,838,226; 5,848,054; 5,905,442; 6,687,487; 6,803,728; and corresponding foreign patents. U.S. and foreign patents pending. Lutron and the sunburst logo are registered trademarks and Stanza is a trademark of Lutron Electronics Co., Inc. © 2008 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. Made and printed in the U.S.A. P/N 030-996 Rev. A 6 /08
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1.1-111 Instance ID : uuid:b1613bae-34c0-411d-87f4-1203a0f32c30 Document ID : adobe:docid:indd:c74e7684-3232-11dd-b82a-ac4c19f22906 Rendition Class : proof:pdf Create Date : 2008:06:25 11:51:53-04:00 Modify Date : 2008:06:25 11:53:55-04:00 Metadata Date : 2008:06:25 11:53:55-04:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 12323 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 1 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools