Lutron Electronics 0075 Remote Control User Manual

Lutron Electronics Company Inc Remote Control

User Manual

Lutron Electronics Co., Inc.
7200 Suter Road Coopersburg, PA 18036-1299 P/N 040399 Rev. A 09/2013 ®
Troubleshooting
Symptoms Possible Causes
Light does not respond
to PicoR wireless control
• The dimmer/switch failed to pair with PicoR wireless control; see Set-Up.
• The dimmer/switch has already received and responded to a command or is already at the light setting the PicoR
wireless control is sending.
• The PicoR wireless control is outside the 30 ft (9 m) operating range.
• The battery in the PicoR wireless control is low.
• The battery in the PicoR wireless control is installed incorrectly.
When in set-up mode
the LEDs on the dimmer/
switch flash when trying
to setup with the PicoR
wireless control or sensor.
• The maximum number of PicoR wireless controls or sensors have been paired with the dimmer/switch. More PicoR
wireless controls or sensors can not be added. See Un-pairing a PicoR Wireless Control.
Nightlight LED on the
PicoR wireless control is
not illuminated
• The battery in the PicoR wireless control is installed incorrectly.
• The battery in the PicoR wireless control is low and needs to be replaced.
Important Notes
Please Read Before Installing
1. This install guide provides simple setup instructions for Maestro
WirelessR systems only. If you are using your PicoR wireless
control with any other LutronR system, please refer to the system
setup guide. If you no longer have your system setup guide,
please download the latest version by following the links at
www.lutron.com/pico
2. The PicoR wireless control uses one (1) CR2032 battery. DONOT
use rechargeable batteries. Using improper batteries could damage
the PicoR wireless control. DONOT dispose of the battery in normal
household waste. Please recycle it by taking it to a proper battery
disposal facility, or contact your local waste disposal provider regarding
local restrictions on the disposal or recycling of batteries.
WARNING: Risk of fire, explosion and burns. May result
in serious injury or death. DO NOT recharge, disassemble,
crush, puncture, heat above 212 °F (100°C) or incinerate the
battery. The battery in this device contains Perchlorate
Material - special handling may apply. For more information
visit www.dtsc.ca.gov/hazardouswaste/perchlorate
3. The PicoR wireless control must be paired with dimmer(s) /switch(es)
before it can communicate.
4. Up to 10 PicoR wireless controls can be configured to work together in
a Maestro WirelessR system.
5. The range of the PicoR wireless control is 30 ft (9 m). Performance is
highly dependent on a variety of complex factors such as:
) Distance between system components
) Geometry of the building structure
) Construction of walls separating system components
) Electrical equipment located near system components
6. Clean PicoR wireless control with a soft damp cloth only. DO
NOT use any chemical cleaners.
7. DO NOT paint the PicoR wireless control.
8. DO NOT mount the PicoR wireless control to a metal surface.
Figure 1 Figure 2
Pico® Wireless Control
with Nightlight
Installing the Battery in a PicoR Wireless Control
with Nightlight
1. Place a flathead screwdriver into
the slot at the bottom of the PicoR
wireless control. Twist to open.
DO NOT press buttons without
back enclosure on.
2. Slide a new battery underneath the
contact strap, with the (-) terminal
toward the front of the PicoR
wireless control.
3. Replace the back enclosure.
4. If installing a new battery, proceed to Set-up. If replacing the battery,
confirm proper installation by turning the receiving device on and off
using the PicoR wireless control.
Set-Up (for Maestro WirelessR systems only)
To communicate with other systems or devices, including
RadioRAR2, QS sensor module (QSM), QuantumR, and HomeWorksR
QS, refer to the system setup guides. See www.lutron.com/pico for
more information.
Important: Set up a PicoR wireless control to a dimmer/switch before
use.
1. Press and hold the dimmer/switch tap button (Figure1) for
approximately 6 seconds. Once the LED(s) start to blink slowly,
release the tap button.
2. Press and hold the OFF button on the PicoR wireless control
(Figure 2) for approximately 6 seconds.
3. Once the dimmer/switch pairs with the PicoR wireless control, the
LED(s) on the dimmer/switch and the load will flash 3 times and it will
exit Set-Up mode.
4. Repeat steps 1 to 3 to pair multiple PicoR wireless controls with a
single dimmer / switch. Repeat steps 1 to 3 to pair a single PicoR
wireless control with multiple dimmers / switches.
5. Pressing the Preset button (-3BRL model only) on a PicoR wireless
control will cause all dimmers to go to the favorite light settings.
Switches can be configured to turn ON or OFF. To save a favorite
light setting, adjust all the dimmers/switches controlled by a PicoR
wireless control to the desired light setting. Then press and hold the
Preset button on the PicoR wireless control for 6 seconds until all
LEDs on the dimmers/switches flash several times.
3 V- 10 mA
Lutron, ), HomeWorks, Pico, Maestro Wireless, RadioRA, and Quantum are registered trademarks and RadioRA 2 is a trademark of Lutron Electronics Co., Inc.
© 2013 Lutron Electronics Co., Inc.
PJN-3BRL
PJN-2B
Mounting accessories
sold separately.
For a complete listing of PicoR wireless
mounting accessories, please visit
www.lutron.com/pico
Operation
Preset Button (-3BRL model only)
Tap Once: Devices go to preset levels.
Press and Hold: To save new preset
level or position, press and hold for
6seconds.
OFF Button
Lights dim to off.
English
Technical Assistance www.lutron.com
World Headquarters
For questions concerning the installation or operation of this product, call the
Lutron Technical Support Center. Please provide exact model number when
calling.
TEL +1.610.282.3800
FAX +1.610.282.1243
Toll Free 1.888.LUTRON1
USA, Canada, Caribbean 1.800.523.9466
Mexico +1.888.235.2910
Central/South America +1.610.282.6701
Wireless Control of Multiple Switches
If multiple wireless dimmers/switches are paired with the same PicoR
wireless control, they will perform as follows:
) Pressing the ON button on the
PicoR wireless control
will cause all
dimmers/switches to turn ON fully.
) Pressing the OFF button on the
PicoR wireless control
will cause all
dimmers/switches to turn OFF completely.
) Pressing the Raise button (-3BRL model only) on a
PicoR wireless
control
will cause all dimmers to turn ON and gradually increase in
intensity.
) Pressing the Lower button (-3BRL model only) on a
PicoR wireless
control
will cause all dimmers to gradually decrease in intensity. The
dimmers will not turn off and will remain at low-end.
) Pressing the Preset button (-
3BRL model only
) on a
PicoR wireless
control
will cause all dimmers to return to the favorite light settings.
Switches can be configured to go to ON or OFF. (See Step 5 in Set-Up)
Un-pairing a PicoR Wireless Control
(for Maestro WirelessR systems only)
To un-pair a previously paired PicoR wireless control from your
system, tap the OFF button (Figure 2) on the PicoR wireless control
three times, on the third tap hold for 6 seconds and then tap three
more times. This will remove all dimmers/switches it was previously
paired with.
ON Button
Lights brighten to full intensity.
Raise Button (-3BRL model only)
Lights increase in intensity.
Lower Button (-3BRL model only)
Lights decrease in intensity.
Nightlight
Glows a soft green color.
Indicator LED
Flashes to indicate a button press or
when unit is in programming mode.
European Headquarters
United Kingdom
Lutron EA Ltd.
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
Technical Support:
+44.(0)20.7680.4481
Freephone: 0800.282.107
www.lutron.com/europe
Asian Headquarters
Singapore
TEL +65.6220.4666
FAX +65.6220.4333
Asia Technical Hotlines
Northern China 10.800.712.1536
Southern China 10.800.120.1536
Hong Kong 800.901.849
India +91.11.4051.4300
Indonesia 001.803.011.3994
Japan +81.3.5575.8411
Macau 0800.401
Singapore 800.120.4491
Taiwan 00.801.137.737
Thailand 001.800.120.665853
Other countries +65.6220.4666
http://www.lutron.com/en-US/
Products/Documents/Components/
PicoWirelessController/FCC.html
FCC/IC Information:

Navigation menu