Lutron Electronics 0075 Remote Control User Manual

Lutron Electronics Company Inc Remote Control

User Manual

Lutron Electronics Co., Inc.7200 Suter Road Coopersburg, PA 18036-1299 P/N 040399 Rev. A 09/2013 ®TroubleshootingSymptoms Possible CausesLight does not respond to PicoR wireless control• The dimmer/switch failed to pair with PicoR wireless control; see Set-Up.• The dimmer/switch has already received and responded to a command or is already at the light setting the PicoR wireless control is sending.• The PicoR wireless control is outside the 30 ft (9 m) operating range.• The battery in the PicoR wireless control is low.• The battery in the PicoR wireless control is installed incorrectly.When in set-up mode the LEDs on the dimmer/switch flash when trying to setup with the PicoR wireless control or sensor.• The maximum number of PicoR wireless controls or sensors have been paired with the dimmer/switch. More PicoR wireless controls or sensors can not be added. See Un-pairing a PicoR Wireless Control.Nightlight LED on the PicoR wireless control is not illuminated• The battery in the PicoR wireless control is installed incorrectly.• The battery in the PicoR wireless control is low and needs to be replaced. Important Notes Please Read Before Installing1. This install guide provides simple setup instructions for Maestro WirelessR systems only. If you are using your PicoR wireless control with any other LutronR system, please refer to the system setup guide. If you no longer have your system setup guide, please download the latest version by following the links at www.lutron.com/pico 2. The PicoR wireless control uses one (1) CR2032 battery. DONOT use rechargeable batteries. Using improper batteries could damage the PicoR wireless control. DONOT dispose of the battery in normal household waste. Please recycle it by taking it to a proper battery disposal facility, or contact your local waste disposal provider regarding local restrictions on the disposal or recycling of batteries. WARNING: Risk of fire, explosion and burns. May result in serious injury or death. DO NOT recharge, disassemble, crush, puncture, heat above 212 °F (100°C) or incinerate the battery. The battery in this device contains Perchlorate Material - special handling may apply. For more information visit www.dtsc.ca.gov/hazardouswaste/perchlorate3. The PicoR wireless control must be paired with dimmer(s) /switch(es) before it can communicate.4. Up to 10 PicoR wireless controls can be configured to work together in a Maestro WirelessR system.5. The range of the PicoR wireless control is 30 ft (9 m). Performance is highly dependent on a variety of complex factors such as: ) Distance between system components ) Geometry of the building structure ) Construction of walls separating system components ) Electrical equipment located near system components6. Clean PicoR wireless control with a soft damp cloth only. DO NOT use any chemical cleaners.7. DO NOT paint the PicoR wireless control.8. DO NOT mount the PicoR wireless control to a metal surface.Figure 1 Figure 2Pico® Wireless Control with Nightlight Installing the Battery in a PicoR Wireless Control with Nightlight1. Place a flathead screwdriver into the slot at the bottom of the PicoR wireless control. Twist to open. DO NOT press buttons without back enclosure on.2. Slide a new battery underneath the contact strap, with the (-) terminal toward the front of the PicoR wireless control.3. Replace the back enclosure.4. If installing a new battery, proceed to Set-up. If replacing the battery, confirm proper installation by turning the receiving device on and off using the PicoR wireless control. Set-Up (for Maestro WirelessR systems only) To communicate with other systems or devices, including RadioRAR2, QS sensor module (QSM), QuantumR, and HomeWorksR QS, refer to the system setup guides. See www.lutron.com/pico for more information. Important: Set up a PicoR wireless control to a dimmer/switch before use.1. Press and hold the dimmer/switch tap button (Figure1) for approximately 6 seconds. Once the LED(s) start to blink slowly, release the tap button.2. Press and hold the OFF button on the PicoR wireless control (Figure 2) for approximately 6 seconds.3. Once the dimmer/switch pairs with the PicoR wireless control, the LED(s) on the dimmer/switch and the load will flash 3 times and it will exit Set-Up mode.4. Repeat steps 1 to 3 to pair multiple PicoR wireless controls with a single dimmer / switch. Repeat steps 1 to 3 to pair a single PicoR wireless control with multiple dimmers / switches.5. Pressing the Preset button (-3BRL model only) on a PicoR wireless control will cause all dimmers to go to the favorite light settings. Switches can be configured to turn ON or OFF. To save a favorite light setting, adjust all the dimmers/switches controlled by a PicoR wireless control to the desired light setting. Then press and hold the Preset button on the PicoR wireless control for 6 seconds until all LEDs on the dimmers/switches flash several times. 3 V- 10 mALutron, ), HomeWorks, Pico, Maestro Wireless, RadioRA, and Quantum are registered trademarks and RadioRA 2 is a trademark of Lutron Electronics Co., Inc.© 2013 Lutron Electronics Co., Inc.PJN-3BRLPJN-2BMounting accessories sold separately.For a complete listing of PicoR wireless mounting accessories, please visit www.lutron.com/picoOperationPreset Button (-3BRL model only)Tap Once: Devices go to preset levels. Press and Hold: To save new preset level or position, press and hold for 6seconds. OFF ButtonLights dim to off. EnglishTechnical Assistance www.lutron.comWorld HeadquartersFor questions concerning the installation or operation of this product, call the Lutron Technical Support Center. Please provide exact model number when calling.TEL +1.610.282.3800FAX +1.610.282.1243Toll Free 1.888.LUTRON1USA, Canada, Caribbean 1.800.523.9466Mexico +1.888.235.2910Central/South America +1.610.282.6701 Wireless Control of Multiple Switches If multiple wireless dimmers/switches are paired with the same PicoR wireless control, they will perform as follows: ) Pressing the ON button on the PicoR wireless control will cause all dimmers/switches to turn ON fully.) Pressing the OFF button on the PicoR wireless control will cause all dimmers/switches to turn OFF completely.) Pressing the Raise button (-3BRL model only) on a PicoR wireless control will cause all dimmers to turn ON and gradually increase in intensity.) Pressing the Lower button (-3BRL model only) on a PicoR wireless control will cause all dimmers to gradually decrease in intensity. The dimmers will not turn off and will remain at low-end.) Pressing the Preset button (-3BRL model only) on a PicoR wireless control will cause all dimmers to return to the favorite light settings. Switches can be configured to go to ON or OFF. (See Step 5 in Set-Up) Un-pairing a PicoR Wireless Control (for Maestro WirelessR systems only) To un-pair a previously paired PicoR wireless control from your system, tap the OFF button (Figure 2) on the PicoR wireless control three times, on the third tap hold for 6 seconds and then tap three more times. This will remove all dimmers/switches it was previously paired with.ON ButtonLights brighten to full intensity. Raise Button (-3BRL model only)Lights increase in intensity.Lower Button (-3BRL model only)Lights decrease in intensity.NightlightGlows a soft green color.Indicator LEDFlashes to indicate a button press or when unit is in programming mode.European HeadquartersUnited KingdomLutron EA Ltd.TEL: +44.(0)20.7702.0657FAX: +44.(0)20.7480.6899Technical Support: +44.(0)20.7680.4481Freephone: 0800.282.107www.lutron.com/europeAsian HeadquartersSingaporeTEL +65.6220.4666FAX +65.6220.4333Asia Technical HotlinesNorthern China 10.800.712.1536Southern China 10.800.120.1536Hong Kong 800.901.849India +91.11.4051.4300Indonesia 001.803.011.3994Japan +81.3.5575.8411Macau 0800.401Singapore 800.120.4491Taiwan 00.801.137.737Thailand 001.800.120.665853Other countries +65.6220.4666http://www.lutron.com/en-US/ Products/Documents/Components/ PicoWirelessController/FCC.htmlFCC/IC Information:

Navigation menu