Lutron Electronics 0078 Low Power Transceiver User Manual

Lutron Electronics Company Inc Low Power Transceiver

Contents

User Manual

Troubleshooting GuideSymptom Probable Cause and ActionBacklight does not turn on when screen is touched. Nothing is displayed on the screen.Power not present at keypad• Circuit breaker OFF. Turn ON breaker.Incorrect wiring. • Wire the keypad according to the Installation section.Blue Lutron® screen with “Maintenance” or “Startup failure” at the bottom.Startup failure. • Cycle power to the device. If symptom persists, contact Lutron Technical Support.The Dynamic Keypad does not control dimmers, shades or other system devices.All LEDs on the keypad flash when any button is pressed.• The device is in the Factory Default Settings mode and has not been activated into the system. Use the HomeWorks QS software to verify activation or re-active the device and transfer its database.Device is not communicating with the system.• Device is out of range of an RF signal repeater.Device is not properly programmed.• Program the device using the HomeWorks QS softwareAll LEDs on the keypad flash when any button is pressed.The device is in the Factory Default mode and has not been activated into the system.• Use the HomeWorks QS software to verify activation or re-active the device and transfer its database.The Dynamic Keypad does not enter addressing mode.The Dynamic Keypad is not congured for RF communication.• Use the information screen on the Dynamic Keypad to verify that it is configured for RF communication.• Ensure MUX (pin 3) and MUX (pin 4) are not connected.The Dynamic Keypad does not snap onto the mounting frame as indicated in step 6c.The mounting frame screws may be too tight (Step 3B & 3D).• Remove the Dynamic Keypad, loosen the mounting frame screws and repeat step 6.Returning Dynamic Keypads to Factory SettingsReturning Dynamic Keypads to Factory Settings will remove them from the system and erase all programming.Step 1: Triple tap any button, below the screen, on the Dynamic Keypad. DO NOT release after third tap.Step 2: Keep the button pressed on the third tap until all the buttons start to flash slowly (approximately 3 seconds).Step 3: Immediately release the button and triple tap the button again. The buttons on the Dynamic Keypad will flash quickly.The Dynamic Keypad has now been returned to Factory Settings.Removing Dynamic KeypadsWarranty: For warranty information, please see the Warranty enclosed with the product, or visit www.lutron.com/resiinfo90˚InstallationEnglishLutron Elec tron ics Co., Inc. 7200 Suter RoadCoopersburg, PA 18036-1299Print ed in the U.S.A. 03/11 P/N 043-376 Rev. ANEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Lutron, HomeWorks, and the sunburst logo are registered trademarks of Lutron Electronics Co., Inc. ©2011 Lutron Electronics Co., Inc.Installation InstructionsPlease Read Before InstallingTechnical Assistance: U.S.A. / Canada: 1.800.523.9466 Mexico: +1.888.235.2910 Other Countries: +1.610.282.3800 24 hours a day, 7 days a week.Dynamic KeypadsHQ-J-DK420-WH (434 MHz)HQ-J-DK420-BL (434 MHz)24 V- 113 mAIEC PELV / NECR Class 2Typical Power Consumption*: 1.5 W* Typical Power Consumption test conditions: LCD backlight on at 80%, buttons backlight on at 28%, normal standby mode.3/8 in(10 mm)Click172�722345COM+24 VCOMMUXMUX+24 VTerminals will accept one or two 22 AWG (0.5 mm() or 18 AWG (1.0 mm2) wires.RF Wired66A6B6C�OR7 25 1⁄8(130)2 3⁄8(60)Important NotesEnvironment: Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0 to 90% humidity, non-condensing. Indoor use only.Cleaning: To clean, wipe with a clean damp cloth. DO NOT use any chemical cleaning solutions.RF Device Placement: RF devices must be located within 30 ft (9 m) of an RF signal repeater.Mounting frame: A custom mounting frame is included with the Dynamic Keypad. Only use the screws provided with the mounting frame.Measurements shown as: in (mm)90˚3A3C3B3DIEC PELV / NEC Class 2 cable only.Maximum 1000 ft (305 m)1/2(13)2 1⁄4(57)1/4 (6) to 1 (25)21NOTICE: Do NOT connect to line / mains voltage.Do not gangIncluded in boxRequired for Installation (Not Included)* The Dynamic Keypad consumes 6 PDUs. For more information, see the Dynamic Keypad Spec Sheet (Part # 369294).2B2A4 1⁄4(108)1 5⁄8(41)Note: Mounting frame is visible after installation. Do NOT paint or damage visible surface.Approximately 54 in (1.4 m)Power Supply*120 V~24 V-

Navigation menu