Lutron Electronics 0096 Relay Module User Manual Manual 1

Lutron Electronics Company Inc Relay Module Manual 1

Contents

Manual 1

Lutron Electronics Co., Inc. | 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A.RF CCO Module | Installation041424 Rev. A05/2013 Important Notes: Please read before installing.• For installation by a qualified electrician in accordance with all local and national electrical codes. • Note: Use copper conductors only.• Check to see that the device type and rating is suitable for the application.• DONOT install if product has any visible damage.• If moisture or condensation is evident, allow the product to dry completely before installation.• Operate between 32 °F to 131 °F (0 °C to 55 °C).• 0% to 90% humidity, non-condensing.• For indoor use only. • 24V~or24V- supply and load shall be protected via an approved power source in accordance with IEC/EN61558-2(SELVsupply).LMJ-CCO1-24-B 24V~45mA24V-35mAFCC Information: (LMJ- model only)This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation.Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment. NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorientorrelocatethereceivingantenna.•Increasetheseparationbetweentheequipmentandreceiver.•Connecttheequipmentintoanoutletonacircuitdifferentfromthat to which the receiver is connected.Warranty: For warranty information, please visitwww.lutron.com/TechnicalDocumentLibrary/Warranty.pdfwww.lutron.com/TechnicalDocumentLibrary/Intl_Warranty.pdfLutron and are registered trademarks of Lutron Electronics Co., Inc. ©2013 Lutron Electronics Co., Inc.CCO Status LEDCCO ToggleAdvanced OperationsFor System Setup Guide and tools visit www.lutron.comRFCCOModuleRF CCO Module Operation Reset Factory DefaultsNote: In some instances it may be necessary to reset the RF CCO Module back to factory default settings.ATriple-taptheAdvancedOperations(“ADV”)button,ontheRFCCOModuleandholduntiltheLEDbeginstoashslowly.Within3secondsofashing,releaseandtriple-tapthebuttonagainandtheLEDwillashrapidlyindicatingthattheunithasbeenresettofactorydefaults.BNote: Any associations or programming previously set up with the unit will be lost and will need to be re-programmed.CCO-controlled device does not respond to Wireless Transmitter(s).•Ensure power to the RF CCO Module is properly applied.•Ensure the CCO-controlled device has been properly wired to the RF CCO Module.•Ensure RF CCO module has been activated in the system.•Ensure that the Wireless Transmitter battery is installed correctly.RFCCOModule does not respond toakeypad,wireless controller or sensor.•Improper programming. Program from system programming software.•Out of RF Range. Reposition to be within 30 ft (9 m) of an RF signal repeater.•Already at current level. The RF CCO Module has already responded to a command, or is already at the requested setting.•Wireless controller or sensor batteries low or installed incorrectly. Replace or install batteries properly.•RF interference. Do not run RF CCO Module wires with other power wires or communication wires (e.g., networking, audio, or video signals).TroubleshootingEnglishWheninstallingaRFCCOModule,wirethemoduleasshown.Note: RF CCO Module may also be mounted on or inside a junction box.If installing unit inside a junction box please seeApplicationNote#423.For more information: www.lutron.comInstallation: LMJ-, LMM-, LMQ- modelsTheRFCCOModuleshouldbeinstalledusingthemountingtabsontheenclosure(screwsnotprovided).TheRFCCOModulecanbeinstalledinajunctionboxormarshallingbox(optional)usingtheconduitnut(provided)orwithmountingscrews(notprovided). Please consult local and national electric codes for proper installation.RF CCO Module PlacementRFCCOModulesmustbelocatedwithin30ft(9m)ofanRFsignalrepeater.RFCCOmodulescannotbecontrolledbythesystemuntiltheyareprogrammedusingthesystemprogrammingsoftware.Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.WARNINGInstallation: LMK- and LMN- modelsNECRClass2LMK-CCO1-24-BLMN-CCO1-24-BLMM-CCO1-24-BLMQ-CCO1-24-B24V~45mA24V-35mA SELVContact Closure Output (CCO)24V~or24V-NO(Normally Open)NC(Normally Closed)COM(Common)Note: When wiring CCO output, use 20 AWG to 16 AWG (0.5 mm2 to 1.5 mm2) solid or stranded wire.ToCCO-controlleddevice.Note: CCO Module supply wires can be connected in any polarity.Mountingscrew (2 Supplied)Wire Nut(2 Supplied)24V~or24V-NO(Normally Open)NC(Normally Closed)COM(Common)Note: When wiring CCO output, use 0.5 mm2 to 1.5 mm2 (20 AWG to 16 AWG) solid or stranded wire.ToCCO-controlleddevice.Note: CCO Module supply wires can be connected in any polarity.Conduit Nut21mmknockout openingFor LMN-CCO-24-Buse supplied Twist-on wire connectors. (2 supplied)12310 mmWiringaLeverOperatedConnector(shown)When wiring lever operated connectors (2 supplied) please use 2.5 mm2to4.0mm2(14AWGto12AWG)diameter solid or stranded copper wire. Technical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com

Navigation menu