Lutron Electronics 0096 Relay Module User Manual 041423 RF Relay Module with Softswitch INSTALL

Lutron Electronics Company Inc Relay Module 041423 RF Relay Module with Softswitch INSTALL

Contents

Manual 2

Lutron Electronics Co., Inc. | 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A.RF Relay Module | Installationwith SoftswitchR041423 Rev. A08/2013 Important Notes: • For installation by a qualified electrician in accordance with all local and national electrical codes. • Note: Use copper conductors only.• Check to see that the device type and rating is suitable for the application.• DO NOT install if product has any visible damage.• If moisture or condensation is evident, allow the product to dry completely before installation.• Operate between 32 °F to 131 °F (0 °C to 55 °C).• 0% to 90% humidity, non-condensing.• For indoor use only. Please read before installingLMJ-16R-DV-B 120 / 277 V~ 50 / 60 Hz 16 A 1/2 HP at 120 V~ 11⁄2 HP at 277 V~UL 2043 Plenum RatedLMK-16R-DV-BLMN-16R-DV-BLMM-16R-DV-BLMQ-16R-DV-B220 - 240 V~ 50 / 60 Hz 16 A 6 A Motor (LMK- Model)FCC Information: (LMJ- model only)This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation.Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Warranty: For warranty information, please visit www.lutron.com/TechnicalDocumentLibrary/Warranty.pdfwww.lutron.com/TechnicalDocumentLibrary/Intl_Warranty.pdfLutron and are registered trademarks of Lutron Electronics Co., Inc. ©2013 Lutron Electronics Co., Inc.Load Status LEDRelay ToggleAdvanced OperationsFor System Setup Guide and tools visit www.lutron.comRF Relay ModuleRF Relay Module Operation Reset Factory DefaultsNote: In some instances it may be necessary to reset the RF Relay Module back to factory default settings.ATriple-tap the Advanced Operations (“ADV”) button, on the RF Relay Module and hold until the LED begins to flash slowly.Within 3 seconds of flashing, release and triple-tap the button again and the LED will flash rapidly indicating that the unit has been reset to factory defaults.BNote: Any associations or programming previously set up with the unit will be lost and will need to be re-programmed.TroubleshootingEnglishWhen installing a RF Relay Module, use the supplied conduit nut and wire the module as shown.If installing unit inside a junction box, please see Application Note #423.For more information: www.lutron.comInstallation: LMJ-, LMQ-, and LMM- modelsConduit NutWhite (Neutral)Black (Hot)Red (Switched Hot)To LoadTechnical Assistance | 1.800.523.9466 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com RF Relay Module can be installed in a junction box or marshalling box (optional) using the conduit nut (provided) or with mounting screws (not provided). Please consult local and national electric codes for proper installation.RF Relay Module PlacementRF Relay Modules must be located within 30 ft (9 m) of an RF signal repeater. RF relay modules cannot be controlled by the system until they are programmed using the system programming software.Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.WARNINGInstallation: LMK- and LMN- models Blue (LMK-), Black (LMN-)(Neutral)Brown (LMK-), Red (LMN-)(Line)Black (LMK-), Yellow (LMN-) (Switched Line)Conduit Nut21 mm knockout openingTo LoadFor LMN-16R-DV-B use supplied Twist-on wire connectors. (3 supplied)12310 mmWiring a Lever Operated Connector (shown)When wiring lever operated connectors (3 supplied) please use 14 AWG to 12 AWG (2.5 mm2 to 4.0 mm2) diameter solid or stranded copper wire. 220 - 240 V~ 50/60 HzLoad does not respond to Wireless Transmitter(s).• Ensure breaker to the RF Relay Module is on.• Ensure the load has been properly wired to the RF Relay Module.• Ensure that the RF Relay Module has been activated in the system.• Ensure that the Wireless Transmitter battery is installed correctly.RF Relay Module does not respond to a keypad, wireless controller or sensor.• Improper programming. Program from the system programming software.• Out of RF Range. Reposition to be within 30 ft (9 m) of an RF signal repeater.• Already at current level. The RF Relay Module has already responded to a command, or is already at the requested setting.• Wireless controller or sensor batteries low or installed incorrectly. Replace or install batteries properly.• RF interference. Do not run RF Relay Module wires with other power wires or communication wires (e.g., networking, audio, or video signals).120/277 V~ 50/60 Hz (LMJ- model)220 - 240 V~ 50/60 Hz (LMQ- and LMM- models)

Navigation menu