Lutron Electronics 0104 Bridge User Manual 1 of 2

Download:
Mirror Download [FCC.gov]
Document ID	2211728
Application ID	oYM1SDruMdPHl4w6/dQjLA==
Document Description	User manual 1 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	98.72kB (1234023 bits)
Date Submitted	2014-03-11 00:00:00
Date Available	2014-04-09 00:00:00
Creation Date	2014-02-25 11:07:44
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-02-27 13:46:48
Document Title	User manual 1 of 2
Document Creator	Adobe InDesign CS6 (Windows)

Wireless
quick-start guide
Installing your dimmer
Turn power off at circuit breaker!
Lutron® Smart Bridge,
Pico® remote control & In-wall dimmer
Installation for lights with one wall switch (single-pole)
Remove existing switch from wall
Connect the dimmer
OFF
Love CasétaT Wireless dimmers? Have ideas
for making them better? Tell us what you think
and we’ll extend your warranty by 1 year.
www.casetawireless.com/register.
Ground
1 Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using a wire connector.
Do not remove outside side sections
on dimmers at the end of gang.
2 Connect either of the remaining wires from the
wallbox to either of the remaining wires on the
dimmer using a second wire connector.
‘snap’
3 Connect the remaining wire from the wall to
the remaining wire on the dimmer using a third
wire connector.
Contents supplied
Disconnect all three wires* from the switch.
Pico® remote control
(PJ2-3BRL)
Some lights have one wall switch, while others
have two or more wall switches (such as stair lights,
which have a switch at both the top and bottom of
the stairs). We’ve included instructions for lights with
one wall switch (called a single-pole). If your light
has more than one switch (called a 3-way), please
visit www.casetawireless.com/support/3way
for complete installation instructions and how-to
videos.
Screws (2)
Dimmer at middle has all
side sections removed.
Important note:
Important note:
Each dimmer
has inside side
sections removed.
(If you installed the dimmer next to other dimmers
or switches, you’ll need to install a wallplate with the
correct size/number of openings to accommodate all
the devices.)
Removing side sections reduces the dimmer’s
maximum wattage rating. See the chart below
for maximum wattage information.
Ground
Maximum* wattage derating chart
(120 V~ 50/60 Hz)
Side sections
removed
None
1 side
2 sides
LED &
CFL
150 W
150 W
150 W
Mount the dimmer
Ethernet Cable
Ground
* If your switch has more than 3 wires attached,
see “Installing CasétaT Wireless in a 3-way switch
application” video on
www.casetawireless.com/support/3-way.
600 W
500 W
Turn power on at circuit breaker
Use the screws provided.
or *
Incandescent &
Halogen
ON
Claro® wallplate
(CW-1)
Power Supply
(T-5DC-USB)
Attach the wallplate
Attach the adapter to the dimmer using the
screws provided snap on the wallplate.
Bend back
and forth.
Remove the switch and pull it away from the wall.
Double your warranty
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
We hope you enjoy the convenience of CasétaT Wireless!
Lutron®
Smart Bridge
(L-BDG)
Before you install the dimmer, please watch the
installation video at www.casetawireless.com.
Wire connectors (3)
Remove side sections (if necessary)
Remove the wallplate from switch.
Welcome—and thank you for purchasing a CasétaT
Wireless kit. In order to control your lights from an app
or remote, you’ll need to replace an existing switch with
a CasétaT Wireless in-wall dimmer.
In-wall dimmer
(PD-6WCL)
400 W
* For maximum wattage information when
mixing light bulb types see
www.casetawireless.com/support/ganging.
P/N 0301715 REV A
Tools you’ll need
Flat-head screwdriver
Pliers
Using your CasétaT Wireless kit
Troubleshooting
Phillips-head screwdriver
Symptoms
Download the Lutron® app
Press and hold “off” button on dimmer
LED
up to 150 W
On
Search for “Lutron Caseta”
Darker
CFL
up to 150 W
Lutron
Dimmable LED and CFL light bulbs vary in their
dimming performance. If you’re using these
bulbs and they flicker or turn off, please visit
www.casetawireless.com/support/lowend for
information on adjusting the dimmer for best bulb
performance.
Launch
the hold
Lutron
® app
Press and
“off”
button on remote
“Brighter”
button with
raised icon
is easy to
find in
the dark
The Lutron app will walk you through
setting up your devices.
Lutron
Compatible light bulbs include:
Use
theand
Lutron
Press
hold® app
“off” button on remote
Philips
9290002295
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Off
• Bulbs turn on at
high light level
but do not turn
on at a low
light level.
1. For indoor use only
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C)
Control
your lights
Schedule
your lights
Connect
while away
Add devices
• PicoR remotes
• Dimmers
• Shades
Device Ratings
In-wall dimmer
PD-6WCL
120 V~ 50/60 Hz
LutronR Smart Bridge
L-BDG
5 V- 300 mA
• Wiring error.
• FASST switch on the dimmer
is in the Off position.
• The dimmer is already at the
light level the Pico remote
control is sending.
• The Pico remote control
is outside the 30 ft (9 m)
operating range.
• The Pico remote control
batteries are installed
incorrectly.
• Bulbs turn off
while being
dimmed.
Important notes:
Ecosmart
ECS 30 WW FL 75WE 120
ECS 38 WW FL 90WE 120
• Light not properly installed.
• The Pico remote control
batteries are low.
Favorite
Darker
Pico® remote control
Cree
BA19-08027OMF-12DE26-1U100
CR6
Sylvania
LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30
Light does
not respond
to Pico remote
control.
On
For a complete list of compatible dimmable LEDs
and CFLs, please visit
www.casetawireless.com/support/bulblist.
Feit
A19/DM/LED
PAR38/LEDG5
Replacing light
bulbs using FASST
Pull the FASST
switch out on the
in-wall dimmer to
remove power at the
light socket.
In-wall dimmer
• Breaker is OFF or tripped.
• The dimmer failed to pair
with Pico remote control;
see Pairing the dimmer and
Pico remote control.
FASS™
Front Accessible
Service Switch
Incandescent
up to 600 W
NOTE: You can mix and match dimmable LED and
CFLs, as well as halogen and incandescent light
bulbs, with CasétaT Wireless dimmers.
Light does
not turn on or
in-wall dimmer
LEDs do not
light up.
Off
www.casetawireless.com/LutronApp
Halogen
up to 600 W
• Light bulb(s) burned out.
Brighter (with raised icon)
Works with energy efficient
dimmable light bulbs:
Probable cause and action
• Bulbs flicker
or flash when
dimmed to a low
light level.
Verify bulbs are marked
dimmable and visit
www.casetawireless.com/
support/lowend
for information on adjusting
the dimmer for best
bulb performance.
PicoR remote control
PJ2-3BRL
3 V- 10 mA
(1) CR2032 battery
(included)
Power Supply
T-5DC-USB
5 V- 1000 mA
Go to www.casetawireless.com/support for
additional troubleshooting suggestions.
CAUTION
Use only with permanently installed fixtures with
dimmable LED, dimmable CFL, halogen, or
incandescent lamps. To avoid overheating and
possible damage to other equipment, do not use
to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Warranty
For warranty information, please visit
www.casetawireless.com/warranty.
Lutron, , Claro, and Pico are registered trademarks and FASS
and Caséta are trademarks of Lutron Electronics Co., Inc. NEC is a
registered trademark of the National Fire Protection Association,
Quincy, Massachusetts Google and the Google logo are registered
trademarks of Google Inc., used with permission. Apple is a trademark
of Apple Inc., registered in the U.S. and other countries.
© 2014 Lutron Electronics Co., Inc
P/N 0301715 REV A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2014:02:25 11:07:44-05:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2014:02:27 13:46:48-05:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2014:02:27 13:46:48-05:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:a2a5f6e6-7ada-4da1-83fc-6ecfb90994bd
Original Document ID            : xmp.did:60739E82592368118083D5438296B683
Document ID                     : xmp.id:2C5D5CD9369EE31190ECB266B068812F
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:11DDAFBA369EE31190ECB266B068812F
Derived From Document ID        : xmp.did:11DDAFBA369EE31190ECB266B068812F
Derived From Original Document ID: xmp.did:60739E82592368118083D5438296B683
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:02:25 11:07:44-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 1

EXIF Metadata provided by EXIF.tools