Lutron Electronics 0107 In-wall dimmer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2311379
Application ID	slulOKejx8TpFGSLRor3cw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	83.02kB (1037703 bits)
Date Submitted	2014-06-30 00:00:00
Date Available	2014-06-30 00:00:00
Creation Date	2014-06-18 08:31:55
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-06-18 08:31:59
Document Title	User manual
Document Creator	Adobe InDesign CS6 (Windows)

GrafikTT
English
0301742 Rev A
Installation Instructions
Please Read Before Installing
120 V~ 60 Hz
Dimmers
LED
Incand. / Halogen
GTJ-150
150 W
GT-150
150 W
GT-250M
250 W
600 W
GTJ-250M
250W
RRT-25CL
250 W
HQRT-25CL
250 W
Companion dimmers
For use with HQRT-25CL and RRT-25CL
GT-AD-S
For use with all other models
GT-AD
Ganging and Derating
Installation
Remove wallplate and the switch mounting screws. Leaving all wires attached,
carefully pull the switch out from the wall.
Identify switch type.
350 W
8 maximum
Single-pole – The switch will have
insulated wires connected to two
screws of the same color plus a green
ground screw.
Compatible LEDs
Cree®: 499485; CR6X-PP2
Philips®: 426122(9290002330)(822580)(bc=046677426125)
EcoSmart®: ECO-575L
Sylvania®: 78390 (LED8R20/DIM/SE/830/RP)
FEIT (Utilitech): PAR38/LEDG5
Companion Dimmer
Connect the green wire on the dimmer to the green or bare ground wire in the wallbox (See
Important Note 3 at left).
Connect the same color wire connected to the red wire on the dimmer to the red wire on the
companion dimmer, along with the tagged wire.
Connect the remaining wire to the blue wire on the companion dimmer.
Load Type
LED
Incand. / Halogen
LED
GT-250M
GTJ-250M Incand. / Halogen
RRT-25CL Lutron® Hi-lume®
A-Series LTE LED
HQRT-25CL Driver
Ground
Ground
IMPORTANT NOTICE: FASSTM - Front Accessible Service Switch
To replace bulb(s), power may be conveniently removed by pulling the FASSTM down on the dimmer. After
replacing bulb(s), push the FASSTM back up fully to restore power to the dimmer.
For any procedure, other than routine lamp replacement, power must be turned OFF at the main
electrical panel.
Green
Single-pole
Multi-location
Multi-location
Multi-location
Multi-location
Green
Dimmer Load-Side
Red
Live
Tag
Light
Green
Blue
Neutral
6a
Carefully push wires into the wallbox. Install dimmer/companion dimmer(s) and
snap on wallplate.
Turn ON power at circuit breaker.
If needed, set low-end trim. See Dimming Operation section (at lower left) for
details.
Install dimmer and/or companion dimmer.
Wire connectors provided are for copper wire
only. For aluminum wire, consult an electrician.
Single-pole - Switch will be replaced by a dimmer.
Connect the green ground wire on the dimmer to the green or bare ground
wire in the wallbox. (See Important Note 3 at left.)
Connect the black wire on the dimmer to one of the wires removed from the
switch. If you had taped together two wires (see step 4), connect both wires
to the black wire on the dimmer and remove the tape.
Connect the red wire on the dimmer to the other wire removed from the
switch.
10
Red
Live
Black
Associate GrafikTTM dimmer to Clear Connect® devices (GTJ- models only).
Press and hold the Toggle button on the GrafikTTM dimmer for approximately 6
seconds. Once all of the light bar LEDs begin to flash, release the Toggle button.
Dimmer
Blue
Green
350 W,
8 drivers max
350 W,
8 drivers max
Number of
Companion Dimmers
LED
Press and hold the appropriate button on the device (see pictures below) for
approximately 6 seconds.
Light
2 LED lamps
3 LED lamps
4 LED lamps
5 LED lamps
6 LED lamps
Symptom
Light does not turn On and no
LEDs turn On.
Possible Cause
•	The FASSTM on the dimmer is pulled down to the
Off position.
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Dimmer is miswired. Check wiring.
Unit is non-responsive.
• Cycle power to unit by pulling the FASSTM down
and back up to fully restore power.
Light turns On and dimmer
•	Wire connected to the blue wire on the dimmer is
works, but companion dimmer
not the same wire connected to the blue wire on
does not work.
the companion dimmer. Check wiring.
•	Wire connected to the red wire on the dimmer is
not the same wire connected to the red wire on the
companion dimmer. Check wiring.
Lights repeatedly turn On and
•	Load is less than the minimum load. See the
Off.
Minimum Load Chart to determine the acceptable
minimum load.
Lights are flickering or exhibiting •	Set low-end trim. See Dimming Operation for
poor dimming range.
details.
Additional Information
For warranty details, please visit:
www/lutron.com/warranty
For FCC/IC information, please visit:
www.lutron.com/fcc-ic
Lutron is a registered trademark and FASS and GrafikT are trademarks of Lutron Electronics Co., Inc.
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
© 2014 Lutron Electronics Co., Inc.
Technical Assistance
Off
LUTRON
Pico®
Wireless Controller
IMPORTANT
Cap the blue wire with the blue connector.
This wire does not get connected.
Load Type
Incandescent /
Halogen
40 W
80 W
120 W
160 W
200 W
For performance or compatibility information, Lutron recommends visiting our website www.
lutron.com/LED, which is constantly being updated.
Ground
Neutral
Troubleshooting
Dimmer Black
Green
350 W,
8 drivers max
Red
Companion
Dimmer
Tag
Middle of Gang
150 W
400 W
250 W
400 W
	Designed for use with permanently installed LED, incandescent, or tungsten halogen only.
Application
Light
Neutral
Remove wallplate from the GrafikTTM dimmer and any companion dimmer, but
leave wallplate adapter connected.
120 V~
60 Hz
FASSTM - Front Accessible Service Switch
Note: FASSTM is not available on companion
dimmers.
Tag
The switch may have two wires attached to the same screw. Tape these two
wires together before disconnecting. Proceed to disconnect the wires from the
switch.
IMPORTANT
Toggle
•	Touch to turn Off or to
turn On to previous light
level
•	Toggle button is white
when On, orange when
Off
Companion
Dimmer
Dimmer
Blue
End of Gang
150 W
500 W
250 W
500 W
Tag
Different-colored screw
Dimming Operation
Adjust
•	Touch to set lights to
desired level
• Slide to adjust light level
Red
Black
Tag
Not Ganged
150 W
600 W
250 W
600 W
Minimum Load Chart
Red
Live
1. C
 AUTION: To avoid overheating and possible damage to other equipment, do
not use to control receptacles, fluorescent lighting fixtures, motor-operated
appliances, transformer-supplied appliances, or electronic low-voltage
lighting fixtures.
2. Install in accordance with all national and local electrical codes.
3. W
 hen no “grounding means” exist in wallbox, the NEC® allows dimmer without
a grounding connection to be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic attachment screws or 2) the
circuit is protected by a ground fault circuit interrupter (GFCI). For this type of
installation, cap or remove the green ground wire on the dimmer, and use an
appropriate wallplate, such as a Lutron® GrafikTTM series wallplate.
4. GrafikTTM dimmers are not compatible with standard 3-way switches. Use only with
companion dimmers (GT-AD-S or GT-AD).
5. C
 ompanion dimmers (GT-AD-S or GT-AD) cannot be used individually but must be
used in conjunction with a GrafikTTM dimmer in a multi-location application.
6. In any multi-location circuit, use only one GrafikTTM dimmer with up to four
companion dimmers.
7. GrafikTTM dimmer settings such as Light Bar Intensity and Speaker On/Off can be
modified using Advanced Programming Mode. For instructions and information on
how to use Advanced Programming Mode, please visit www.lutron.com/grafikT or
call Lutron® Technical Support at 1.800.523.9466.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Control 1
GT-150
GTJ-150
Dimmer Line-Side
Important Notes
Set Low-End Trim:
1. Press and hold bottom of
light bar (approximately 5
seconds) until Toggle button
flashes orange.
2. Slide finger on light bar to
adjust to desired brightness.
3. To exit, press and hold the
Toggle button (approximately
5 seconds) until the Toggle
button stops flashing.
When combining controls in the same wallbox, derating is required. No derating is
required for companion dimmers.
Dimmer
Connect the green ground wire on the dimmer to the green or bare ground wire in the wallbox
(See Important Note 3 at left).
Connect tagged wire removed from the switch to the black wire on the dimmer.
Connect one of the remaining wires removed from switch to the red wire on the dimmer.
Connect the remaining wire removed from the switch to the blue wire on the dimmer.
Multi-location – 3-way switches will have
insulated wires connected to three screws
plus a green ground screw. One of the wires is
connected to a screw of a different color (not
green) or labeled COMMON. Tag this wire.
For a complete list of compatible LEDs, please visit: www.lutron.com/LED
Set High-End Trim:
1. Press and hold top of
light bar (approximately 5
seconds) until Toggle button
flashes orange.
2. Slide finger on light bar to
adjust to desired brightness.
3. To exit, press and hold the
Toggle button (approximately
5 seconds) until the Toggle
button stops flashing.
One location will be replaced by a GrafikTTM dimmer and the other location(s) by a GrafikTTM
companion dimmer. The dimmer can be wired on the line-side or the load-side.
ARNING! Shock Hazard. May result in serious injury or death.
! WTurn
off power at circuit breaker before installing the unit.
Hi-lume® A-Series LTE LED Drivers
—
6b Multi-location - Lights can be dimmed from multiple locations.
Turn OFF power at circuit breaker.
Occupancy /
Vacancy Sensor
Daylight Sensor
Once the dimmer associates the recently added devices, the LEDs and load will
flash 3 times and the GrafikTTM dimmer will exit set-up mode.
1.800.523.9466 U.S.A. | Canada | Caribbean
+1.888.235.2910 Mexico
+1.610.282.3800 Others
www.lutron.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2014:06:18 08:31:55-04:00
Metadata Date                   : 2014:06:18 08:31:59-04:00
Modify Date                     : 2014:06:18 08:31:59-04:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:f9e3627c-efd1-4781-a500-c28e9725beb3
Original Document ID            : xmp.did:0CB2F27BD0E5E311A384BBAB1FAA0CF5
Document ID                     : xmp.id:60B58483E4F6E311804BDF7A62176D6B
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:5FB58483E4F6E311804BDF7A62176D6B
Derived From Document ID        : xmp.did:FFC47EA25BF6E311804BDF7A62176D6B
Derived From Original Document ID: xmp.did:0CB2F27BD0E5E311A384BBAB1FAA0CF5
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:06:18 08:31:55-04:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 1
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools