Lutron Electronics 0111 Wireless In-Wall Dimmer Switch User Manual

Lutron Electronics Company Inc Wireless In-Wall Dimmer Switch

User Manual

OFFONx3x2Hold for 6 seconds until LEDs start blinkingquick-start guideIn-wall dimmerWelcome—and thank you for purchasing a CasétaTM Wireless in-wall dimmer. In order to control your lights from an app or remote, you’ll need to replace an existing switch with a CasétaT Wireless in-wall dimmer.Before you install the dimmer, please watch the installation video at www.casetawireless.com/supportWe hope you enjoy the convenience of CasétaTM Wireless!NOTE: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs, with CasétaTM Wireless dimmers. Dimmable LED and CFL light bulbs vary in their dimming performance. If you’re using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.For a complete list of compatible dimmable LEDs and CFLs, please visit www.casetawireless.com/bulblistCompatible light bulbs include:Cree® BA19-08027OMF-12DE26-1U100 CR6-575LEcoSmart® ECS BR30 W27 FL 120 ECS 20 WW FL 50WE 120Feit® A19/OM/LED Philips® 9290002295Sylvania® LED12A19/DIM/O/827 LED21PAR38/DIM/P/930/FL30LED—up to 250 WCFL—up to 250 WContents suppliedDouble your warrantyIn-wall dimmer (PD-10NXD)Tools you’ll needWorks with energy efficient dimmable light bulbs:Flat-head screwdriverWire connectorsx5 x2Phillips-head screwdriverPliersScrewsInstallation for lights with one wall switch (single pole)Installing your dimmerUsing your CasétaT Wireless kit (sold separately)If you have more than one switch controlling the light, this is called a 3-way installation. You will need to buy PJ2-WALL-WH-L01. Please visit www.casetawireless.com/3way for more details.WARNING: SHOCK HAZARDMay result in serious injury or death. Turn off power at circuit breaker or fuse before installing.1 Turn power off at circuit breaker!1 Press and hold “off” button on dimmer2 Press and hold “off” button on remote4 Connect the dimmer5 Mount the dimmer6 Attach the wallplate7 Turn power on at circuit breaker2 Remove existing switch from wallRemove the wallplate from switch.3 Remove side sections (if necessary)Remove the switch and pull it away from the wall.* If your switch has more than 3 wires attached, see “Installing Caséta Wireless in a 3-way switch application” video at www.casetawireless.com/3wayBend back and forth.351234146GroundGroundGroundOptional72Disconnect all three wires* from the switch.1 Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the dimmer using a wire connector.2 Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.3 Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.4 If available, connect the white neutral wire. Required for: MLV loads, LED drivers, PHPM-PA, PHPM-3F, GRX-TVI.Do not remove outside side sections on dimmers at the end of gang.Each dimmer has inside side sections removed.Dimmer at middle has all side sections removed.Attach the adapter to the dimmer using the screws provided and snap on the wallplate.‘snap’(If you installed the dimmer next to other dimmers or switches, you’ll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)Use the screws provided.Pairing the dimmer and Pico® remote controlGo to www.casetawirless.com/support for additional troubleshooting suggestions.Symptoms Probable cause and actionLight does not turn on or in-wall dimmer LEDs do not light up.• Light bulb(s) burned out.• Breaker is OFF or tripped.• Light not properly installed.• Wiring error.• FASSTM switch on the dimmer is in the Off position.Light does not respond to Pico® remote control.• The dimmer failed to pair with Pico® remote control; see Pairing the dimmer and Pico® remote control.• The dimmer is already at the light level the Pico® remote control is sending.• The Pico® remote control is outside the 30 ft (9 m) operating range.• The Pico® remote control battery is low.• The Pico® remote control battery is installed incorrectly.• Bulbs turn off while being dimmed.• Bulbs turn on at high light level but do not turn on at a low light level.• Bulbs flicker or flash when dimmed to a low light level.Verify bulbs are markeddimmable and visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.Love CasétaTM Wireless dimmers? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/registerFor advanced features, tips for using CasétaTM Wireless dimmers with CFLs and LEDs, the complete CasétaTM Wireless product line, and more, please visit www.casetawireless.com/featuresChanging the favorite light level on the Pico® remote control (sold separately)You can use the round “favorite” button on the Pico® remote control to recall a favorite light level. We’ve set it to 50%, but you can change it to any level you like.FavoriteReplacing light bulbs using FASSTMPull the FASSTM switch out on the in-wall dimmer to remove power at the light socket.CAUTIONUse only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent,lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.CodesInstall in accordance with all national and local electrical codes.GroundingWhen no “grounding means” exist in wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.FCC/IC InformationThis device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.Lutron, , and Pico are registered trademarks and FASS, Caséta, and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Google and the Google logo are registered trademarks of Google Inc., used with permission.© 2015 Lutron Electronics Co., Inc P/N 0301778 REV ALutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299, U.S.A. 1212Hold for 6 seconds until LEDs blink twice on in-wall dimmer. New favorite level is now saved.3 Set desired light level on dimmer4 Press and hold “favorite” button on remoteImportant Note: 3-WayTroubleshootingHold for 6 seconds until lights flash 3 times.Device RatingsIn-wall dimmerPD-6WCL120 V~ 50/60 HzImportant notes:1. For indoor use only. 2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).Repeat steps to pair other Pico® remote controls.WirelessPico® remote control (sold separately)OnOffDarkerBrighter (with raised icon) FASS™Front Accessible Service SwitchIn-wall dimmerOnOffDarkerFavoriteBrighterWith a smartphone or tablet (Bridge required, sold separately)1 Press and hold “off” button on dimmer2 Press and hold “off” button on remoteThe Lutron® app will walk you through setting up your devices.Download the Lutron® appwww.casetawireless.com/LutronAppLaunch the Lutron® appLutronThe CasétaT Wireless dimmer can be controlled from a smartphone when used with the LutronR Smart BridgeT. If you are using the dimmer and remote control with the LutronR Smart BridgeT follow the instructions below.Search for “Lutron Caseta”3 Press and hold “off” button on remoteUse the Lutron® app to complete ALL remaining stepsLutronLutronR Smart BridgeTNote: If you are using the dimmer and remote control with another manufacturer’s bridge, please refer to that manufacturer’s instructions for set-up.LutronLutronR appApple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.Without a smartphone or tablet (Bridge not required)WarrantyFor warranty information, please visit www.casetawireless.com/warrantyP/N 0301778 REV AIncandescent / Halogen—up to 1000 WMLV—up to 1000 WControl three ways Add devices • PicoR remotes • Dimmers • Shades Schedule your lightsConnect while awayImportant note:Removing side sections reduces the dimmer’s maximum wattage rating. See the chart below for maximum wattage information.* For maximum wattage information when mixing light bulb types see www.casetawireless.com/gangingMaximum* wattage derating chart (120 V~ 50/60 Hz)Side sections removed None 1 side 2 sidesLED & CFL 250 W 250 W 250 Wor*Incandescent, Halogen, & MLV 1000 W 800 W 600 W3Switch 1 Switch 2Using your controls

Navigation menu