Lutron Electronics 0111 Wireless In-Wall Dimmer Switch User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2579572
Application ID	Ff5rk0gM2BFvXKM7BcVSUA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	130.04kB (1625509 bits)
Date Submitted	2015-04-09 00:00:00
Date Available	2015-04-09 00:00:00
Creation Date	2015-04-03 17:03:30
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-04-06 08:06:07
Document Title	Caseta Wireless In-wall Dimmer Quick-Start Guide (0301729)
Document Creator	Adobe InDesign CS6 (Windows)

Wireless
quick-start guide
Installing your dimmer
Turn power off at circuit breaker!
In-wall dimmer
Installation for lights with one wall switch (single pole)
OFF
Double your warranty
Do not remove outside side sections
on dimmers at the end of gang.
Each dimmer
has inside side
sections removed.
Dimmer at middle has all
side sections removed.
Important note:
Removing side sections reduces the dimmer’s
maximum wattage rating. See the chart below
for maximum wattage information.
If you have more than one switch controlling the
light, this is called a 3-way installation. You will need
to buy PJ2-WALL-WH-L01.
Maximum* wattage derating chart
(120 V~ 50/60 Hz)
Ground
x2
Tools you’ll need
None
1 side
2 sides
LED & CFL
250 W
250 W
250 W
Works with energy efficient
dimmable light bulbs:
LED—up to 250 W
CFL—up to 250 W
800 W
600 W
Using your CasétaT Wireless kit
NOTE: You can mix and match dimmable LED and
CFLs, as well as halogen and incandescent light
bulbs, with CasétaTM Wireless dimmers.
Compatible light bulbs include:
Cree®
BA19-08027OMF-12DE26-1U100
CR6-575L
ON
Using your controls
Without a smartphone or tablet (Bridge not required)
The CasétaT Wireless dimmer can be controlled from a smartphone
when used with the LutronR Smart BridgeT.
Pairing the dimmer and
Pico® remote control
If you are using the dimmer and remote control with the LutronR
Smart BridgeT follow the instructions below.
Note: If you are using the dimmer and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
instructions for set-up.
LutronR app
Press and hold “off” button on dimmer
Changing the favorite light level
on the Pico® remote control
(sold separately)
Troubleshooting
Symptoms
Light does not
turn on or in-wall
dimmer LEDs do
not light up.
Off
Favorite
Set desired light level on dimmer
Probable cause and action
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
On
Brighter (with raised icon)
Darker
You can use the round “favorite”
button on the Pico® remote
control to recall a favorite light
level. We’ve set it to 50%, but you
can change it to any level you like.
Hold for 6 seconds
until LEDs start
blinking
Download the Lutron® app
Press and hold “off” button on dimmer
Light does not
respond to Pico®
remote control.
• FASSTM switch on the dimmer is
in the Off position.
• The dimmer failed to pair with
Pico® remote control; see
Pairing the dimmer and Pico®
remote control.
• The dimmer is already at the
light level the Pico® remote
control is sending.
FASS™
Front Accessible
Service Switch
• The Pico® remote control
is outside the 30 ft (9 m)
operating range.
In-wall dimmer
• The Pico® remote control
battery is low.
Search for “Lutron Caseta”
Dimmable LED and CFL light bulbs vary in their
dimming performance. If you’re using these
bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend for information
on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs
and CFLs, please visit
www.casetawireless.com/bulblist
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
(sold separately)
With a smartphone or tablet (Bridge required, sold separately)
Turn power on at circuit breaker
* For maximum wattage information when
mixing light bulb types see
www.casetawireless.com/ganging
* If your switch has more than 3 wires attached, see
“Installing Caséta Wireless in a 3-way switch application”
video at www.casetawireless.com/3way
LutronR Smart BridgeT
MLV—up to 1000 W
1000 W
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Lutron
Incandescent / Halogen—up to 1000 W
FCC/IC Information
Ground
P/N 0301778 REV A
‘snap’
(If you installed the dimmer next to other dimmers
or switches, you’ll need to install a wallplate with the
correct size/number of openings to accommodate all
the devices.)
Mount the dimmer
Use the screws provided.
Side sections
removed
Incandescent,
Halogen, & MLV
Pliers
Please visit www.casetawireless.com/3way for
more details.
4 If available, connect the white neutral wire.
Required for: MLV loads, LED drivers, PHPM-PA,
PHPM-3F, GRX-TVI.
or *
Phillips-head screwdriver
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
3 Connect the remaining wire from the wall to
the remaining wire on the dimmer using a third
wire connector.
Switch 2
Codes
Install in accordance with all national and local
electrical codes.
2 Connect either of the remaining wires from the
wallbox to either of the remaining wires on the
dimmer using a second wire connector.
Disconnect all three wires* from the switch.
Switch 1
Ground
1 Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using a wire connector.
Important Note: 3-Way
• The Pico® remote control
battery is installed incorrectly.
Replacing light bulbs using FASSTM
Pull the FASSTM switch out on the in-wall dimmer to
remove power at the light socket.
Lutron
www.casetawireless.com/LutronApp
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Launch
the hold
Lutron
® app
Press and
“off”
button on remote
Press and hold “off” button on remote
On
Brighter
Hold for 6 seconds
until lights flash 3 times.
EcoSmart®
ECS BR30 W27 FL 120
ECS 20 WW FL 50WE 120
x3
The Lutron® app will walk you through
setting up your devices.
Feit®
A19/OM/LED
Philips®
9290002295
Pico® remote control (sold separately)
Repeat steps to pair other
Pico® remote controls.
Favorite
Darker
Off
Press and hold “favorite” button on remote
Lutron
• PicoR remotes
• Dimmers
• Shades
Control
three ways
Schedule
your lights
Hold for 6 seconds until LEDs
blink twice on in-wall dimmer.
New favorite level is now saved.
Important notes:
x2
Press
hold® app
“off”tobutton
on remote
Use
theand
Lutron
complete
all remaining steps
Add devices
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
In-wall dimmer
(PD-10NXD)
x5
Attach the adapter to the dimmer using the
screws provided and snap on the wallplate.
Bend back
and forth.
Remove the switch and pull it away from the wall.
Contents supplied
CAUTION
Use only with permanently installed fixtures with
dimmable LED, dimmable CFL, halogen, or
incandescent,lamps. To avoid overheating and
possible damage to other equipment, do not use
to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Attach the wallplate
Love CasétaTM Wireless dimmers? Have ideas
for making them better? Tell us what you think
and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
Screws
Optional
Warning: Shock Hazard
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
We hope you enjoy the convenience of CasétaTM Wireless!
Sylvania®
LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30
Connect the dimmer
Before you install the dimmer, please watch the
installation video at
www.casetawireless.com/support
Flat-head screwdriver
Remove side sections (if necessary)
Remove the wallplate from switch.
Welcome—and thank you for purchasing a CasétaTM
Wireless in-wall dimmer. In order to control your lights
from an app or remote, you’ll need to replace an existing
switch with a CasétaT Wireless in-wall dimmer.
Wire connectors
Remove existing switch from wall
Connect
while away
For advanced features, tips for using CasétaTM Wireless dimmers with CFLs and LEDs, the complete CasétaTM Wireless
product line, and more, please visit www.casetawireless.com/features
• Bulbs turn off
while being
dimmed.
Verify bulbs are marked
dimmable and visit
www.casetawireless.com/
lowend for information on
• Bulbs turn on
adjusting the dimmer for best
at high light
level but do not bulb performance.
turn on at a low
light level.
• Bulbs flicker
or flash when
dimmed to a
low light level.
Go to www.casetawirless.com/support for
additional troubleshooting suggestions.
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Device Ratings
In-wall dimmer
PD-6WCL
120 V~ 50/60 Hz
Lutron, , and Pico are registered trademarks and FASS, Caséta, and
Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a
registered trademark of the National Fire Protection Association, Quincy,
Massachusetts. Google and the Google logo are registered trademarks of
Google Inc., used with permission.
© 2015 Lutron Electronics Co., Inc
P/N 0301778 REV A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Create Date                     : 2015:04:03 17:03:30-04:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2015:04:06 08:06:07-04:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Title                           : Caseta Wireless In-wall Dimmer Quick-Start Guide (0301729)
Description                     : Caseta Wireless In-wall Dimmer Quick-Start Guide (0301729)
Subject                         : Caseta Wireless In-wall Dimmer Quick-Start Guide (0301729), Lutron, 0301729, Caseta Wireless, In-wall Dimmer, Quick-Start Guide, 030-1729, PD-6WCL, LED, CFL, MLV, INCANDESCENT, HALOGEN
Metadata Date                   : 2015:04:06 08:06:07-04:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:67a46454-6b7b-4b54-b069-fece51240087
Original Document ID            : xmp.did:60739E82592368118083D5438296B683
Document ID                     : xmp.id:DA7946D144DAE411BAB3A56357A00ECA
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:D97946D144DAE411BAB3A56357A00ECA
Derived From Document ID        : xmp.did:831B89743FDAE411BAB3A56357A00ECA
Derived From Original Document ID: xmp.did:60739E82592368118083D5438296B683
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:04:03 17:03:30-04:00
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 1

EXIF Metadata provided by EXIF.tools