Lutron Electronics 0111 Wireless In-Wall Dimmer Switch User Manual
Lutron Electronics Company Inc Wireless In-Wall Dimmer Switch
User Manual
OFF
ON
x3
x2
Hold for 6 seconds
until LEDs start
blinking
quick-start guide
In-wall dimmer
Welcome—and thank you for purchasing a CasétaTM
Wireless in-wall dimmer. In order to control your lights
from an app or remote, you’ll need to replace an existing
switch with a CasétaT Wireless in-wall dimmer.
Before you install the dimmer, please watch the
installation video at
www.casetawireless.com/support
We hope you enjoy the convenience of CasétaTM Wireless!
NOTE: You can mix and match dimmable LED and
CFLs, as well as halogen and incandescent light
bulbs, with CasétaTM Wireless dimmers.
Dimmable LED and CFL light bulbs vary in their
dimming performance. If you’re using these
bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend for information
on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs
and CFLs, please visit
www.casetawireless.com/bulblist
Compatible light bulbs include:
Cree®
BA19-08027OMF-12DE26-1U100
CR6-575L
EcoSmart®
ECS BR30 W27 FL 120
ECS 20 WW FL 50WE 120
Feit®
A19/OM/LED
Philips®
9290002295
Sylvania®
LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30
LED—up to 250 W
CFL—up to 250 W
Contents supplied
Double your warranty
In-wall dimmer
(PD-10NXD)
Tools you’ll need
Works with energy efficient
dimmable light bulbs:
Flat-head screwdriver
Wire connectors
x5 x2
Phillips-head screwdriver
Pliers
Screws
Installation for lights with one wall switch (single pole)
Installing your dimmer
Using your CasétaT Wireless kit (sold separately)
If you have more than one switch controlling the
light, this is called a 3-way installation. You will need
to buy PJ2-WALL-WH-L01.
Please visit www.casetawireless.com/3way for
more details.
WARNING: SHOCK HAZARD
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
1 Turn power off at circuit breaker!
1 Press and hold “off” button on dimmer
2 Press and hold “off” button on remote
4 Connect the dimmer
5 Mount the dimmer
6 Attach the wallplate
7 Turn power on at circuit breaker
2 Remove existing switch from wall
Remove the wallplate from switch.
3 Remove side sections (if necessary)
Remove the switch and pull it away from the wall.
* If your switch has more than 3 wires attached, see
“Installing Caséta Wireless in a 3-way switch application”
video at www.casetawireless.com/3way
Bend back
and forth.
3
5
1
2
3
4
1
4
6
Ground
Ground
Ground
Optional
7
2
Disconnect all three wires* from the switch.
1 Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using a wire connector.
2 Connect either of the remaining wires from the
wallbox to either of the remaining wires on the
dimmer using a second wire connector.
3 Connect the remaining wire from the wall to
the remaining wire on the dimmer using a third
wire connector.
4 If available, connect the white neutral wire.
Required for: MLV loads, LED drivers, PHPM-PA,
PHPM-3F, GRX-TVI.
Do not remove outside side sections
on dimmers at the end of gang.
Each dimmer
has inside side
sections removed.
Dimmer at middle has all
side sections removed.
Attach the adapter to the dimmer using the
screws provided and snap on the wallplate.
‘snap’
(If you installed the dimmer next to other dimmers
or switches, you’ll need to install a wallplate with the
correct size/number of openings to accommodate all
the devices.)
Use the screws provided.
Pairing the dimmer and
Pico® remote control
Go to www.casetawirless.com/support for
additional troubleshooting suggestions.
Symptoms Probable cause and action
Light does not
turn on or in-wall
dimmer LEDs do
not light up.
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASSTM switch on the dimmer is
in the Off position.
Light does not
respond to Pico®
remote control.
• The dimmer failed to pair with
Pico® remote control; see
Pairing the dimmer and Pico®
remote control.
• The dimmer is already at the
light level the Pico® remote
control is sending.
• The Pico® remote control
is outside the 30 ft (9 m)
operating range.
• The Pico® remote control
battery is low.
• The Pico® remote control
battery is installed incorrectly.
• Bulbs turn off
while being
dimmed.
• Bulbs turn on
at high light
level but do not
turn on at a low
light level.
• Bulbs flicker
or flash when
dimmed to a
low light level.
Verify bulbs are marked
dimmable and visit
www.casetawireless.com/
lowend for information on
adjusting the dimmer for best
bulb performance.
Love CasétaTM Wireless dimmers? Have ideas
for making them better? Tell us what you think
and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
For advanced features, tips for using CasétaTM Wireless dimmers with CFLs and LEDs, the complete CasétaTM Wireless
product line, and more, please visit www.casetawireless.com/features
Changing the favorite light level
on the Pico® remote control
(sold separately)
You can use the round “favorite”
button on the Pico® remote
control to recall a favorite light
level. We’ve set it to 50%, but you
can change it to any level you like.
Favorite
Replacing light bulbs using FASSTM
Pull the FASSTM switch out on the in-wall dimmer to
remove power at the light socket.
CAUTION
Use only with permanently installed fixtures with
dimmable LED, dimmable CFL, halogen, or
incandescent,lamps. To avoid overheating and
possible damage to other equipment, do not use
to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC®) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Lutron, , and Pico are registered trademarks and FASS, Caséta, and
Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a
registered trademark of the National Fire Protection Association, Quincy,
Massachusetts. Google and the Google logo are registered trademarks of
Google Inc., used with permission.
© 2015 Lutron Electronics Co., Inc
P/N 0301778 REV A
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
1
2
1
2
Hold for 6 seconds until LEDs
blink twice on in-wall dimmer.
New favorite level is now saved.
3 Set desired light level on dimmer
4 Press and hold “favorite” button on remote
Important Note: 3-Way
Troubleshooting
Hold for 6 seconds
until lights flash 3 times.
Device Ratings
In-wall dimmer
PD-6WCL
120 V~ 50/60 Hz
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Repeat steps to pair other
Pico® remote controls.
Wireless
Pico® remote control (sold separately)
On
Off
Darker
Brighter (with raised icon)
FASS™
Front Accessible
Service Switch
In-wall dimmer
On
Off
Darker
Favorite
Brighter
With a smartphone or tablet (Bridge required, sold separately)
1 Press and hold “off” button on dimmer
2 Press and hold “off” button on remote
The Lutron® app will walk you through
setting up your devices.
Download the Lutron® app
www.casetawireless.com/LutronApp
Launch the Lutron® app
Lutron
The CasétaT Wireless dimmer can be controlled from a smartphone
when used with the LutronR Smart BridgeT.
If you are using the dimmer and remote control with the LutronR
Smart BridgeT follow the instructions below.
Search for “Lutron Caseta”
3 Press and hold “off” button on remote
Use the Lutron® app to complete ALL remaining steps
Lutron
LutronR Smart BridgeT
Note: If you are using the dimmer and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
instructions for set-up.
Lutron
LutronR app
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Without a smartphone or tablet (Bridge not required)
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
P/N 0301778 REV A
Incandescent / Halogen—up to 1000 W
MLV—up to 1000 W
Control
three ways
Add devices
• PicoR remotes
• Dimmers
• Shades
Schedule
your lights
Connect
while away
Important note:
Removing side sections reduces the dimmer’s
maximum wattage rating. See the chart below
for maximum wattage information.
* For maximum wattage information when
mixing light bulb types see
www.casetawireless.com/ganging
Maximum* wattage derating chart
(120 V~ 50/60 Hz)
Side sections
removed None 1 side 2 sides
LED & CFL 250 W 250 W 250 W
or*
Incandescent,
Halogen, & MLV 1000 W 800 W 600 W
3
Switch 1 Switch 2
Using your controls