Lutron Electronics 0116 Wireless Fixture Sensor User Manual UserManual

Lutron Electronics Company Inc Wireless Fixture Sensor UserManual

UserManual

Lutron Electronics Co., Inc. 7200 Suter RoadCoopersburg, PA 18036-1299 USARelease Wires from Connectors Press connector buttons while pushing the wires slightly inward. Pull wires outward to release the wires from the connectors. Do NOT pull out the wires without using the connector buttons, as damage to the product can occur.Packaging Fixture packaging must protect the installed wireless fixture control so that it does not get damaged in shipping.Customer Assistance | 1.844.LUTRON1 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com Part of the Vive FamilyClear Connect Wireless Fixture ControllersRequired Components For each fixture, you will need:Clear Connect Wireless Fixture Controller (with Occupancy Sensor)(DFCSJ-OEM-OCC)Clear Connect Wireless Fixture Controller (RF Only) (DFCSJ-OEM-RF)Start HereEnglishImportant Notes: • Forinstallationbyaqualiedxturemanufacturer.• Usecopperconductorsonly.• Checktoseethatthedevicetypeandratingissuitablefortheapplication.•DO NOTinstallifproducthasanyvisibledamage.• Ifmoistureorcondensationisevident,allowtheproducttodrycompletelybefore installation.• Operatebetween32°Fand131°F(0°Cand55°C),ambient.• 0%to90%humidity,non-condensing.• Forindooruseonly.• Sensorshouldbemountedtoxtureinorientationthatmakesitparalleltotheoorwhenxtureisinstalledinceiling.DFCSJ-OEM-OCC Clear Connect Wireless Fixture Controller (with Occupancy Sensor)DFCSJ-OEM-RF Clear Connect Wireless Fixture Controller (RF Only)InstallClearConnectWirelessFixtureController• Ensureknockoutandadjacentsurfacesarefreefromburrs,oil,chemicals,debris,etc.• DonotpushonthePIRlensorbuttontoinstallthewirelessfixturecontrol.Pushonthecenterofthewireless fixture control.Connector(poke-instyle)• 18to22AWG(0.75to0.3mm2)solidcopperwire• Wirestriplength:0.31in(8mm)Mounting ThicknessSnapsenablemountingtothefollowingmaterialthicknessranges:• 0.04in(1mm)orless• 0.041to0.08in(1.1to2mm)• 0.081to0.13in(2.1to3.3mm)WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.Formoreinformation,see www.lutron.com/TechnicalDocumentLibrary/3691039.pdfPlease read before installing.+One Fixture Control At least one EcoSystem driver + Wireless Sensor Interface (PS-OEM-2W-UNV)OrAt least one driver with self-powered DALI link19.5–20.5 V-80-250 mA041600 Rev. A03/2017* For set-up, programming, andtroubleshooting with a Vive system,please refer to the installationinstructions included with the Vive hubor at www.lutron.comClear Connect Wireless Fixture Controllers UL2043PlenumRatedControlsupto4ballastsordrivers(IEC60929AnnexE.2requireseachballastordrivertolimitthesink/sourcecurrentdrawto2.0mAmaximum). DefaultFunctionalityFixture ControlsAuto On level: DFCSJ-OEM-OCC only (notapplicableforDFCSJ-OEM-VAC orDFCSJ-OEM-RF) Varieswithambientlightlevelwhenoccupancyistriggered(e.g.,100%foradarkroom,10%forabrightroom).Timeout period:15minutesConnector buttons0.04in(1mm)or less0.041to0.08in(1.1to2mm)0.081to0.13in(2.1to3.3mm)DaylightingSensorDonotinstallindirectviewofthelightsourceorreflectingsurface.PIRSensor• Installinalocationthatallowsthesensortohaveanunobstructedviewofthearea.• Installawayfromradiatedheatgivenoffbythelightsource.TemperatureThewirelessfixturecontrolisratedfor55°C(131°F)maximum.Productmustbeinstalledinanareathatwillnotallowittoexceedthisrating.Keepawayfromheatgeneratingdevices(e.g.,drivers)andverifyduringthefixturedesignprocess.WiringBestPractices(forRFconsideration)• Keepallthefixturewiringtotheminimumlengthneededtoachievetheconnectionsinanorganizedmanner.Avoidunnecessaryslackinthewires.• Ifthedriverisprovidedwithagroundterminal,thisterminalmustbeelectricallyconnectedtothegroundedfixturemetalusingagroundwirethatisnolongerthan2in(51mm).• Mechanically affix all the wires to the fixture wall so that they are kept as close possible to the grounded fixture metal.• Ensurethatthedriverwiringisasfaraspossiblefromthewiringimmediatelyconnectedtothewirelessfixturecontrol• EnsurethatthewirelessfixturecontrolismountedawayfromtheLEDstripstominimizethecouplingoftheRFradiationfromtheLEDstripsinto the wireless fixture control.• Formoreinformation,seewww.lutron.com/TechnicalDocumentLibrary/048620.pdfWirelessfixturecontroller(RFonly)•TheWirelessfixturecontroller(RFonly)(DFCSJ-OEM-RF)canbeinstalledonthebackofthefixture,assumingmetaltilesarenotbeingused.• TheWirelessfixturecontroller(RFonly)willberatedforuseinplenumareas.• Donotfullyenclosewithinthemetalfixture.MountingtoCurvedSurfacesMountingdirectlytoacurvedsurfaceisnotrecommended.Anadaptor(custommanufacturedbytheOEM)mayberequiredtoensurethatthedeviceisseatedproperly.Remote MountingThe wireless fixture control is intended for troffer and linear fixtures and is not intended to be ceiling mounted.WiringDiagrams120–277V~120–277V~Wireless sensor interfaceEcoSystem/DALIdriverDriverwithself-poweredDALIlinkEcoSystemdriverDriverwithself-poweredDALIlinkClear Connect Wireless Fixture ControllerClear Connect Wireless Fixture ControllerButtonButtonPIRlensDaylightsensor lensDaylightsensor lensORFCC information and IC informationThisdevicecomplieswithpart15oftheFCCRulesandIndustryCanadalicense-exemptRSSstandard(s).Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseinterference,and(2)thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesiredoperation.ModicationsnotexpresslyapprovedbyLutronElectronicsCo.,Inc.couldvoidtheuser’sauthoritytooperatethisequipment.NOTE: This equipment has been tested and found to comply with the limitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedto try to correct the interference by one or more of the following measures:• Re-orientorrelocatethereceivingantenna.• Increasetheseparationbetweentheequipmentandreceiver.• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.Clear Connect Wireless Fixture Controllers with Ecosystem or DALI DriverWireless Fixture Control with Driver with Self-powered DALI LinkNLS+S-E+E1E-E2Wireless sensor interface120–277V~
ALL PROGRAMMING IS OPTIONALProgramming is not required for default functionalityResetFactoryDefaults Note:Insomeinstances,itmaybenecessarytoresetthe xturecontrollersandconnecteddevicesbacktofactorydefaultsettings.Beforebeginning,makesurethatalldevicesareconnectedandpowered.A Rapidly tap the button on the  xture controller three times andholdonthefourthuntiltheLEDbeginstoashslowly;release button.BWithin1secondofreleasingthebutton,againrapidlytapthebuttonthreetimesandtheLEDswillashrapidlyindicating that the unit has been reset to factory defaults. Note:Anyassociationsorprogrammingpreviouslysetupwith the  xture control will be erased and will need to be re-programmed.Clear Connect Wireless Fixture ControllersPart of the Vive FamilyLimited Warranty: http://www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdfTroubleshooting * www.lutron.comSymptom SolutionSensordoesnotrespondto motion.• Sensorrequires2-minutewarmupperiodfrompowerresetbeforesensingcircuitisactive.Defaulttimeoutis15minutes.LightsdonotdimorturnONasexpected.• EnsurethatcontrollinesarewiredproperlyLightsareunstableatlow-end.• Adjustlow-endtrim.RefertoVivedocumentationonwww.lutron.com.Customer Assistance | 1.844.LUTRON1 USA, Canada, and the Caribbean | +44.(0)20.7702.0657 Europe | +1.610.282.3800 Others | www.lutron.com Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299 USALutron,Pico,PowPak,EcoSystem,andEnergiTriPakaretrademarksofLutronElectronicsCo.,Inc.registeredintheU.S.andothercountries.RadioPowrSavrandVivearetrademarksofLutronElectronicsCo.,Inc.NECisaregisteredtrademarkoftheNationalFireProtectionAssociation,Quincy,Massachusetts. ©2017LutronElectronicsCo.,Inc.* For set-up, programming, and troubleshooting with aVive system, please refer to the installation instructionsincluded with the Vive hub or atwww.lutron.comRecommended end-of-line test1. Providepowertoxture.2. Fixturewillgotothedriver’ssavedlevel.3. Pressthebuttontotoggletheloadstate.LightwillfadetoON(orOFF)over1second.GreenLEDwillstaylitfor2secondsafterreleasing the button.4. Toggletheloadagain(ifnecessary)toensurethelightsareon.ThiswillmakesurethelightsturnONwhenpowerisappliedthenexttime(atjobsite).5. Removepower.If testing occupancy sensor functionality:1. Applypowertoxture.2. Pressbutton(ifnecessary)toturnlightsoff.3. Waitfor2minutesforsensoroccupancycircuittobecomeactive4. Providemotioninfrontofsensor-lightswillturnON.5. Lightswillnottunoffautomaticallyfor15minutesafterlastmotion detection.If testing daylight sensor functionality:1. Applypowertoxture.Fixtureshouldturnontofull(highend).Ifnot,pressbuttononsensor.2. Shinelightsource(ashlight)directlyintodaylightlens.Fixturelightwilldimdownover1minute(holdashlightsteadilyinplace).3. Coverdaylightlens/buttonwithopaquematerial.Fixturelightwilldimupover1minute(holdopaquematerialsteadilyinplace)

Navigation menu