Lutron Electronics 0118 Dimmer Module User Manual 20180912 v1 11 Install 041675a

Lutron Electronics Company Inc Dimmer Module 20180912 v1 11 Install 041675a

User Manual_20180912_v1 - 11_Install_041675a

041588 Rev. A08/2018PowPak | InstallationControl Module with EcoSystemTestLink Cal. +For each system, ensure that you have:One PowPak Control Module At least one Wireless Transmitter At least one EcoSystem LED Driver or Fluorescent BallastRequired ComponentsRadio Powr Savr Occupancy/Vacancy Sensor (10 maximum)Radio Powr Savr Daylight Sensor(1 maximum)Pico Remote Control(10 maximum)64 mA for the control lines. May be pre-installed in light fixture.Note: All drivers and ballasts used with Vive wireless controls must comply with the limits for a Class A device, pursuant to Part 15 of the FCC rules.PowPak Control Module with EcoSystem (1 maximum)RaiseToggleLowerTop LEDConsult third-party DALI fixtures installation guide for fixture-specific wiring. This device can be installed on a fixture / troffer, junction box, or marshalling box using the conduit nut or with mounting screws. The device must NOT be mounted inside a fixture / troffer or other metallic enclosure. Improper installation can result in degraded wireless communication, intermittent or sustained communication failures, and will not be covered under warranty. For mounting and wiring best practices see Lutron Application Note #620 (P/N 048620).+Occupancy SensorsDaylight SensorWireless ControlsOccupied: All lights 100%.Unoccupied: All lights off.TestLink Cal.All lights dim in response to daylight.On All lights 100%Favorite All lights 50%Off All lights offDefault Functionality2A The PowPak Control Module with EcoSystem can be installed on a fixture / troffer, junction box, or marshalling box using the conduit nut (provided) or with mounting screws (not provided). Please consult local and national electric codes for proper installation.B Once installed, energize the PowPak Control Module with EcoSystem.C Use the Toggle “ u” , Raise “▲” and Lower “Δ” buttons to verifycontrol wiring. EnglishAll Wireless Transmitters must be installed within 9 m (30 ft) of the PowPak Control Module with EcoSystem.EcoSystem Control: 18 V- 64 mA120 – 277 V~ 50 / 60 Hz 80 mARMJS-ECO32-SZA Connect mains wiring (hot, neutral) to each fixture.B Connect EcoSystem control to each fixture.1E1E2NEUHOTDALIMAINSTo additional EcoSystem fixturesNeutralLine/HotE1E2+–WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.Sample LED driver shownImportant Notes: Please read before installing.For installation by a qualified electrician in accordance with all local and national electrical codes.•Use copper conductors only.•Check to see that the device type and rating is suitable for the application.•DO NOT install if product has any visible damage.•If moisture or condensation is evident, allow the product to dry completelybefore installation.•Operate between 0 °C and 40 °C (32 °F and 104 °F) ambient.•0% to 90% humidity, non-condensing.•For indoor use only.Start HereXViveProgramming with a Vive Hub3Mount, Wire, and Install EcoSystem Devices and Lighting FixturesConsult third-party device installation guideInstall PowPak Control Module with EcoSystemSuggested Installation Location: Center of room to ensure proper RF coverage of area. A Use an iOS or Android compatible device. B Download the Lutron Vive app. C Open the app and follow the instructions. Note: For further information on set up, programming, and troubleshooting with a Vive system, please refer to the installation instructions included with the Vive hub or visit www.lutron.com/viveNote: For programming the PowPak Control Module with EcoSystem without a Vive hub see reverse side.Customer Assistance www.lutron.com/support Troubleshooting www.lutron.com /viveBallasts cannot be controlled locally from PowPak Control Module with EcoSystem.• Ensurethatthebreaker(s)tothePowPak Control Module are energized.• EnsurethattheEcoSystem control lines are wired to the lighting fixture(s).Reset to factory defaults.Lights do not dim as expected. • EnsurethatEcoSystem control lines are wired properly.Lights do not respond to Wireless Transmitter(s).•Ensure that the breaker(s) to the PowPak Control Module with EcoSystem and drivers/ballasts are energized.• EnsurethatWirelessTransmittersareassociatedtothePowPak Control Module with EcoSystem.Reset to factory defaults.Lights are unstable at low-end or flash/flicker at turn-on or turn-off. • Adjustthelow-endtrim.Wireless Transmitter(s) cannot be associated to PowPak Control Module with EcoSystem.• ThemaximumnumberofWirelessTransmittershavebeenassociatedtothePowPak Control Module with EcoSystem. To remove a previously set up WirelessTransmitter, tap a Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.Part of the Vive Familyvive.lutron.comXEcoSystem to FixturesE1 (Violet)E2 (Violet/White)Neutral (White)Line / Hot (Black)Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036041675 Rev. A 08/2018Bottom LED9 mmaximumRadio Powr Savr Occupancy SensorPico Remote ControlPowPak Control ModuleInstall in center of room to maximize RF coverage.PowPak Control ModuleWire Gauge Maximum DALI-compliant Bus Wire Length1.5 mm2 (14 AWG) 300 m0.75 mm2 (18 AWG) 150 m0.5 mm2 (20 AWG) 100 m
PowPak | InstallationProgramming without a Vive HubControl Module with EcoSystemPart of the Vive Family Start HereLutron, Pico, and PowPak are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Radio Powr Savr and Vive are trademarks of Lutron Electronics Co., Inc. App Store is a trademark of Apple Inc., registered in the U.S. and other countries. iOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. Android, Google Play and the Google Play logo are trademarks of Google Inc. DALI is a trademark of ZVEI. ©2013 – 2018 Lutron Electronics Co., Inc. A On PowPak Control Module with EcoSystem, hold Toggle button “ u” for 6 seconds until lights flash.Both LEDs will begin flashing twice per second.Associate Wireless Transmitters to PowPak Control Module with EcoSystem Before beginning this step, make sure that there are no other PowPak modules being set up within the same building. It is possible that wireless transmitters from other systems can be incorrectly associated to this module.1 C On PowPak Control Module with EcoSystem, hold Toggle button “ u” for 6 seconds to save association. Lights will return to high end and LEDs will stop flashing. B Hold the indicated button on each transmitter for 6seconds. Lights will flash to show that wireless transmitters have been associated. LEDs also flash on successful association.TestLinkCal. D Permanently install wireless transmitters (consult individual component installation guides for information).Raise LowerFavoriteSet a Favorite Light Level (Optional)For Pico remote controls with a Favorite Button. A Adjust lights to desired level:Use the Raise button “ ” or Lower button “ ” on the Pico remote control. B Save favorite level:Press and hold the Favorite button for 6seconds. The load will flash 3 times to confirm that the Favorite level is saved.3 Low-End Trim A Enter low-end trim adjustment mode: Press and hold the Lower button “Δ” on the fixture control for 12 seconds. The lights will flash and the bottom LED will begin flashing. B Adjust the low-end trim: Use the Raise button “▲” and Lower button “Δ” on the control module to adjust and set the lights to the desired low-end (0.1 to 45%). C Save the low-end trim: Press and hold the Toggle button “ u” for 6seconds to save setting. The bottom LED will begin flashing and then turn solid to indicate new level has been saved. High-End Trim A Enter high-end trim adjustment mode: Press and hold the Raise button “▲” on the fixture control for 12seconds. The lights will flash and the top LED will begin flashing. B Adjust the high-end trim: Use the Raise button “▲” and Lower button “Δ” on the control module to adjust and set the lights to the desired high-end (55 to 100%). C Save the high-end trim: Press and hold the Toggle button “ u” for 6seconds to save setting. The load status LED will begin flashing and then turn solid to indicate new level has been saved. Set Low-End Trim and High-End Trim (Optional)For best results, minimize the amount of sunlight entering the room before performing the following procedures. Notes Depending on the fixture manufacturer or load, low-end trim and high-end trim may need to be adjusted. • Trimlow-endtoensureastablelightlevelbecausesomeloadswillickerordropoutif trimmed too low. • Besurethatyoucanturnonthelightstothelow-endtrimlevelwithoutanyabnormaloperation. • Thefactorydefaulthigh-endtrimissuitableformostapplicationsbutcanbeadjustedas desired.45Set Minimum Light Level (Optional)Certain applications (e.g., hallways), may require that the lights never turn off. For these areas, activate Minimum Light Level mode. A Enter minimum light level adjustment mode:Press and hold Toggle button “ u” and Lower button “Δ” for 12 seconds. Lights will flash high-low-high and both LEDs will begin flashing.If lights stop flashing and turn off, the minimum light level is set to OFF (default).If lights stop flashing and go to low-end, the minimum light level is ON and set to low-end. B Change the minimum light level:Press Raise button “▲” to set minimum light level to low-end.Press Lower button “Δ” to set minimum light level to OFF. C Save the minimum light level:Press and hold Toggle button “ u” for 6seconds. Both LEDs will quickly flash to indicate that new level has been saved.6Set Occupancy Light Levels (Optional)Note: Unoccupied light level is always the minimum light level and cannot be adjusted. A Set desired occupancy light levels:Use Raise/Lower buttons “▲ /Δ” on the PowPak Control Module with EcoSystem or Raise/Lower buttons “ / ” on all associated Pico Remote Controls. B Save occupancy light levels:Press and hold Test button for 6 seconds on any associated Radio Powr Savr Occupancy Sensor without a Lights On button. Release when Sensor lens starts to flash.Limited Warranty: www.lutron.com/en-US/ResourceLibrary/warranty/Limited%20Comm.pdfCalibrate the Radio Powr Savr Daylight Sensor Daylight Sensor will control all wired fixtures equally. A Press and release the “Cal.” button on the Daylight Sensor. B Set lights in room to desired light level. C Press and hold the “Cal.” button for 6seconds. D Exit room for 5 minutes to complete calibration.Note: When calibration has completed, all lights will flash and begin to respond to daylight.Multiple Daylight Rows (Optional)For every row of daylighting a separate PowPak Control Module with EcoSystem must be used. For detailed setup refer to the tuning section of the Radio Powr Savr Daylight Sensor installation guide. • SelectthePowPak Control Module with EcoSystem that you want to adjust by pressing the Toggle button.TestLink Cal.2Reset Factory DefaultsNote: In some instances, it may be necessary to reset the PowPak Control Module with EcoSystem and connected devices back to factory default settings. Before beginning, make sure that all devices are connected and powered. A Triple-tap the Toggle button “ u” on the PowPak Control Module with EcoSystem and hold until both LEDs begin to flash slowly; release button. B Within 3 seconds of the start of flashing, triple-tap the same button again and the LEDs will flash rapidly indicating that the unit has been reset to factory defaults.Note: Any associations or programming previously set up with the PowPak will be erased and will need to be re-programmed.Customer Assistance:TEL: +1.844.LUTRON1FAX: +1.610.282.1243www.lutron.com/supportCustomer Assistance www.lutron.com/support FCC / IC InformationThis device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user’s authority to operate this equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Re-orientorrelocatethereceivingantenna.•Increasetheseparationbetweentheequipmentandreceiver.•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

Navigation menu