MEILOON 480200 DLP Projector User Manual DHT100 UserMan
MEILOON INDUSTRIAL CO., LTD. DLP Projector DHT100 UserMan
MEILOON >
Contents
- 1. User Manual 1
- 2. User Manual 2
User Manual 2
INSTALLATION 2-3-4 2-3-4-1 OPERATING THE WIRELESS SPEAKER CONNECTING THE SPEAKERS DRAWING 29 2-3-4-2 OPERATING THE SPEAKERS A. Make sure the AC voltage selector (115V or 230V) is selected for your local voltage (Factory preset is on 230V). B. Connect the power cord into a wall outlet. C. Turn on the power switch on the rear panel of the speaker. D. Make sure the wireless channel of the speaker that is selected is the same as the wireless channel of the transmitter that is selected in the projector. (Please check the OSD, it will be described in the section of "3-2-2-4 Audio") E. Adjust the volume with volume knob on the rear panel of the speaker. Signal Input LINE INPUT SPEAKER OUTPUT VOLUME Volume Knob P.L. CHANNEL SELECTOR Channel Selector EIKI INDUSTRIAL CO., LTD. Signal Output SPEAKER MODELNO. :WSP1 NPUT:1 V/ SERI ALNO. :XXXXXXXX Hz1 Meiloon W24025 FCC ID:RRT480200 AUDIO SYSTEM 86AC E241996 MADE IN CHINA R33803 Bar-code (45x13mm) DOUBLE INSULATION When servicing only use identical parts POWER AC VOLTAGE SELECTOR AC Voltage Selector Power Switch 230V~ 115V~ POWER CONSUMPTION: 100W RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: SHOCK HAZARD-DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR. CAUTION To reduce the risk of fire, replace with only the same type and rating of fuse. FUSE: T 1A L/250V AC Power Inlet DRAWING 30 DHT100/200 3. Control Panel and Remote Control 3-1 CONTRO PANELL AND REMOTE CONTROL You can control the projector's functions through the Control Panel and Remote Control. 3-1-1 1. 2. 3. 4. USING THE CONTROL PANEL MENU: Press once to display the OSD.Press again to exit the OSD. DRAWING 31 UP/SOURCE: This button is dual function. UP: Cursor function or make an adjustment based on your selection of a function. SOURCE: Selects "Composite Video", "S-Video", "Component-I Video (YCbCr)", "Analog YPbPr", "DVD Player", "Media player", "Computer", "TV" sources. DOWN/SYNC: This button is dual function. DOWN: Cursor function or make an adjustment based on your selection of a function. SYNC: Optimizes the signal from PC LEFT: Cursor function or make an adjustment based on your selection of a function. 5. RIGHT: Cursor function or make an adjustment based on your selection of a function. 6. ENTER: Confirms your selection item. 7. EJECT/ROTATE: This button is dual function. EJECT: Eject a DVD ROTATE: Rotates the photo 90 degrees clockwise on screen, but this function can't be accessed when Slideshow is playing. 8. II/PAUSE: This button is dual function. II: Pauses when playing the DVD disc. PAUSE: Pauses when playing photos. 9. PLAY/SLIDE: This button is dual function. 10 11 PLAY: Plays a DVD. SLIDE: Displays the photos on your memory card as a slide show, with (MP3) music if available on your memory card. DHT100/200 10. ECO: Using the projector in this mode will save lamp life and reduce fan noise. You can use this mode for watching video in a room with reduced ambient lighting. USER CONTROLS 3-1-2 USING THE REMOTE CONTROL LED indicator 10m Section A 30 30 Section B Section C Section D 30 O 30 O Section E 10m DRAWING 32 DRAWING 33 DHT100/200 USER CONTROLS There are five sections on the Remote Control as described below. LED indicator: The LED will light when the Remote Control is functioning. If not, please check your batteries. Section A: BLUE characters, for PROJECTOR use 1. POWER: Powers On/Off the projector 2. ZOOM-: Reduces the image size (For projecto r use) 3. ZOOM+: Increases the image size (For projector use) 4. MUTE: Mutes the audio output. Press once for Mute on ,press again for mute off. 5. SLEEP: Turns off the projector after a period. (So the time you need---0ff, 15min, 30min, 45min, 60min) 6. FREEZE: Freezes the image. 7. SYNC: Optimizes the signal from PC 8. SOURCE: Selects "Composite Video", "S-Video", "Component-I Video (YCbCr)", "Analog YPbPr", "DVD Player", "Media player", "Computer", "TV" sources. 9. KEYSTONE: Adjusts image distortion caused by tilting the projector (+/- 12 degree) 10. ASPECT: Selects the aspect ratio.(4:3,16:9,1:1) 11. IMAGE MODE: Three modes can be selected. (Theater/Computer, Standard, User) 12. MENU: Displays the MENU of your playing device. Press once to display, twice to disappear. Section B: RED characters, for MEDIA PLAYER use 13. PLAY and PAUSE: PLAY: Plays program PAUSE: Pauses the program. When playing slideshow with music, press once to pause the slideshow, press again to pause the MP3 music. 14. MUSIC SLIDE: Plays slideshow with music 15. PHOTO: Plays the photos 16. PREV/RW PREV: Selects the previous photo RW: Rewinds the program 17. STOP: Stops the program 18. SETUP: Enters the OSD of the Media player. (If you are playing a program, please stop it first). 19. ROTATE: Rotates the photo (This function can't be executed when playing a slideshow) 20. NEXT and FW: NEXT: Selects the previous photo FW: Forward the program 21. INFORMATION : Shows the information (resolution) of the displaying photo. 22. SELECT: a. Selects the card you want when different cards are inserted simultaneously. DHT100/200 b. Return to start-up screen. USER CONTROLS Section C: BLACK Characters, for ANY SOURCE use These are "Common Keys". They can be used with any source. 23. VOL -: Decreases the volume of either the internal speaker or the external speaker. 24. VOL +: Increases the volume of either the internal speaker or the external speaker. 25. UP: Moves up when selecting item. 26. LEFT: Moves left when selecting item. 27. RIGHT: Moves right when selecting item. 28. DOWN: Moves down when selecting item. 29. ENTER: Confirms your selection. Section D: GREEN characters, for DVD PLAYER use 30. PLAY: Plays the program. 31. STOP: Stops the program. 32. FF: Fast-forwards the program. 33. FR: Fast-rewinds the program. 34. SF: Slow-forwards the program. 35. SR: Slow-rewinds the program. 36. NEXT: Selects the next song or chapter. 37. PREV: Selects the previous song or chapter. 38. YCbCr : This key can't be used on this model. 39. YPbPr: This key can't be used on this model. 40. PAUSE/STEP: PAUSE: Pauses the program. STEP: Plays the disc step by step. 41. VCD AUDIO: Selects a VCD language. (if the VCD is recorded in two languages) This function can't work while playing a DVD. 42. EJECT: Ejects the disc from the DVD player. 43. SUBTITLE: Selects the language of the subtitle. 44. LANGUAGE: Selects the language of the dub. (If the disc is recorded with multi-language) 45. MENU: Enters the menu of the DVD disc. 46. SETUP: Stops the program, press this button to enter the OSD of the DVD player, and then set the function you need. Section E: BROWN characters, for TV TUNER use 47. SAP: Second audio program. 48. AV/TV: Changes the mode between AV and TV 49. CH JUMP: Channel jump. 50. CH +: Next channel 51. CH -: Previous channel 52. Fine tune: Fine tune the TV signal 53. 0-9 KEYS: Selects the TV channel. DHT100/200 USER CONTROLS ON-SCREEN DISPLAY MENUS 3-2-1 HOW TO OPERATE 1. To Open the ON-Screen Display (OSD) menu, press the "Menu" button on the Remote Control or Control Panel . 2. When the OSD is displayed, use "Cursor" buttons on the Control Panel or on the Remote Control to choose the item you need. 3. Press the "Menu" button again to exit. 3-2-2 PROJECTOR'S OSD IMAGE DISPLAY SYSTEM OSD Location Projection Lamp Hours Lamp Reset Int/Ext Speaker Auto Source Factory Reset LANGUAGE English Deutsch Francais Espanol 繁體中文 簡體中文 TV Auto Search Channel Add/Del Channel Fine Tune Volume Mode TV System NTSC sys. setting PAL sys. setting DHT100/200 AUDIO SYSTEM LANGUAGE TV COMPUTER IMAGE Brightness Contrast Frequency Tracking Hor. Position Ver. Position Image Mode VIDEO IMAGE Brightness Contrast Color Satur. Sharpness Tint Image Mode DISPLAY Aspect Ratio Zoom Keystone Color Temperature AUDIO Volume Treble Bass Mute Int/Ext Speaker Wireless Channel set High Brightness Gamma High Brightness Gamma Red Color Temperature Green Color Temperature Blue Color Temperature Wireless Channel setting 3-2 USER CONTROLS 3-2-2-1 MAIN MENU Press the “Enter" button to enter the submenu, press it again to return to the main menu. Main Menu includes: Image Display Audio System Language TV DRAWING 34 3-2-2-2 IMAGE Computer Image Brightness: Adjusts the brightness of the image. Contrast: Adjusts the contrast of the image Frequency: Adjusts the frequency to match the frequency of your computer's graphic card. Tracking: Synchronizes the signal timing with your computer's graphic card. Hor. Position: Moves the image's horizontal position. DRAWING 35 Ver. Position: Moves the image's vertical position. Image Mode: Choose a mode Computer: This mode is good for computer signals. Standard: This mode is good for movie pictures. User: This mode allows you to adjust High Brightness and/or Gamma. Press the "Right" button to enter the submenu. High Brightness: Sets the white peaking level of the DMD chip. If you prefer a stronger image, press the "Right" button to increase the value. If you want a more natural image, press the" Left" button to decrease the value. DRAWING 36 Gamma: Adjusts the Gamma (mid-tone brightness) curve. DHT100/200 USER CONTROLS Video Image Brightness: Adjusts the brightness of the image. Contrast: Adjusts the contrast of the image Color Satur. : Adjusts color saturation of the image. Sharpness: Adjusts the sharpness of the image. Tint: Adjusts the color balance of red and green . Image Mode: See "Image Mode" in the "Computer Image" section. 3-2-2-3 DRAWING 37 DISPLAY Aspect Ratio: Selects your desired aspect ratio. Zoom: Increases or reduces the size of the image. Keystone: Adjusts image distortion caused by tilting the projection. Color Temperature: Adjusts the color temperature of the image. A higher color temperature looks colder. A lower color temperature looks warmer. When the color temperature is set to User mode, press "Down" button to select Red, Green, or Blue adjustment. DHT100/200 DRAWING 38 Red, Green, Blue: Increases or decreases the value to find the desired color temperature. USER CONTROLS 3-2-2-4 AUDIO Volume: Adjusts the volume of the internal or wireless speaker. Treble: Adjusts the treble audio of the internal or wireless speaker Bass: Adjusts the Bass audio of the internal or wireless speaker. Mute: Mutes the internal or wireless speaker. Int/Ext Speaker: Selects the internal or wireless speaker. If you select wireless speaker, press the "Down" button to get the wireless channel selection. Set the wireless speaker channel to match the wireless speaker channel set on the projector. Press the " Enter " button to return to the main menu. Wireless CH.: Sets the wireless channel. DRAWING 39 3-2-2-5 DRAWING 40 SYSTEM OSD Location:Chooses the OSD location on the display screen. Projection: Selects the projector's orientation. Front: The factory default setting. For "tabletop" projection. Front Ceiling: Inverts the image. For "ceiling mounted" projection. Rear: Reverses the image. For "tabletop"rear projection Rear Ceiling: Reverses and inverts the image. For "ceiling mounted" rear projection. DRAWING 41 Lamp Hours: Displays the cumulative lamp operation time. Lamp Reset: Resets the lamp operation time after changing lamps.. Auto Source: Detects the input source automatically. Factory Reset: Resets all items in all menus to their default settings. DHT100/200 USER CONTROLS 3-2-2-6 LANGUAGE Selects the Language you need. DRAWING 42 3-2-2-7 TV Auto Search: Searches channels automatically. Add Channel: Adds the channel you need. Del Channel: Deletes the channel you don't need. Fine Tune: Mutes the internal speaker of projector or wireless speaker. Volume Mode: Mono: Outputs the mono sound. Stereo: Outputs the stereo sound. Sub-Language: Changes the main language to the sub-language. DRAWING 43 TV System: Selects the NTSC or PAL system. NTSC: Selects Country. PAL: Selects region and volume system DHT100/200 DRAWING 45 DRAWING 44 USER CONTROLS 3-2-3 MEDIA PLAYER'S OSD Press the "Setup"(red) button on the Remote Control to enter the Media Player's OSD. PHOTO SETUP MUSIC SETUP PHOTO SETUP Thumbnail digest On, Off MUSIC SETUP Repeat mode One, All, Off SLIDESHOW SETUP Slideshow mode Folder repeat Interval time Transition Auto start SLIDESHOW SETUP MOVIE SETUP PREFERENCE MOVIE SETUP Interval time Repeat mode PREFERENCE OSD Language Defaults Firmware Auto, Manual One, All, Off One, Three, Five, Ten seconds Full Screen TOP -> BOTTOM BOTTOM -> TOP TB -> CENTER CENTER -> TB BLIND: T -> B LEFT -> RIGHT RIGHT -> LEFT L/R -> CENTER On, Off Fast, Normal Off, One, All English Chinese Chinese F French German Japanese Spanish Reset Edition Update DHT100/200 USER CONTROLS 3-2-3-1 MAIN MENU The Menu can only be accessed from the Remote Control. 1. Press "Setup" button to show the main menu on screen 2. Press "Up" / "Down" button to select the item. 3. Press "Enter" button to enter the sub-menu. 4. Press "Right" button to set the function. 5. Press "Enter" button to confirm the setting 6. Press "Left" button to return the function item. 7. Select "EXIT SETUP" to exit the setup main. Main Menu includes: DRAWING 46 PHOTO SETUP MUSIC SETUP SLIDESHOW SETUP MOVIE SETUP PREFERENCES 3-2-3-2 PHOTO SETUP Digital cameras automatically store a thumbnail of each picture taken. These thumbnails load faster and allow you to browse photos more easily. The Media Player can detect and display these thumbnails. The PHOTO SETUP function lets you turn the THUMBNAIL DIGEST on or off. If you select on, you can view your photos more quickly. Submenu DHT100/200 DRAWING 48 DRAWING 47 USER CONTROLS 3-2-3-3 MUSIC SETUP Submenu DRAWING 49 DRAWING 50 Repeat Mode ONE—Repeats the selected song. ALL—Repeats all the songs in the memory card. OFF—Does not repeat any songs. 3-2-3-4 SLIDESHOW SETUP DISPLAY MODE — Set to cause the slideshow to start automatically. REPEAT MODE —Set to cause all photos in a folder to display consecutively and continuously (in a loop). INTERVAL TIME —Set the show time of each photo. (One, Three, Five, or Ten sec). TRANSITION — Set the transition mode between slides. FULL SCREEN —Image appears full screen TOP -> BOTTOM —Image rolls in from top to bottom DRAWING 51 BOTTOM -> TOP —Image rolls in from bottom to top TB -> CENTER —Image rolls in from top and bottom to center Submenu CENTER -> TB —Image rolls from center to top and bottom BLIND: T -> B— Image rolls in blinds from top to bottom LEFT -> RIGHT—Image rolls in from left to right RIGHT -> LEFT—Image rolls in from right to left L/R -> CENTER—Image rolls in from left and right to center DRAWING 52 DHT100/200 USER CONTROLS AUTO START — When turned on, any media in the memory card plays automatically when the card is inserted. 3-2-3-5 MOVIE SETUP INTERVAL TIME FAST: A short preview of movie plays in Thumbnail view. NORMAL: The whole movie plays in Thumbnail view. REPEAT MODE OFF: REPEAT MODE is turned off. ONE: Plays the selected movie continuously (loop). ALL: Plays all movies on the memory card continuously(loop). Submenu DRAWING 53 3-2-3-6 DRAWING 54 PREFERENCE OSD LANG: Selects the OSD language. DEFAULTS: Returns to the default value. FIRMWARE: Updates the firmware. (For service person use only) DHT100/200 DRAWING 56 DRAWING 55 USER CONTROLS 3-2-4 DVD PLAYER'S OSD Press the "Setup"(green) button on the Remote Control to enter the DVD player's OSD. LANGUAGE LANGUAGE OSD Menu English, 簡體中文, 繁體中文, Francais 日本語, Deutsch, Spanish Subtitle English, 簡體中文, 繁體中文, Francais 日本語, Auto, Off Audio VIDEO DVD menu AUDIO 1 VIDEO TV Shape TV System AUDIO AC3 AUDIO 2 DTS MP3/WMA Others MORE AUDIO Prologic Subwoofer Factory Set English, Chinese S, Chinese T, Francais Japanese, German, Spanish English, Chinese S, Chinese T, Francais Japanese, German, Spanish 4:3, 16:9 NTSC, PAL, PAL60, AUTO Analog Out - 2 Channels, 6 Channels Digital Out - PCM, RAW, OFF Analog Out - 2 Channels, 6 Channels Digital Out - PCM, RAW, OFF Analog Out - 2 Channels, 6 Channels Digital Out - PCM, RAW, OFF Analog Out - 2 Channels, 6 Channels Digital Out - PCM, RAW, OFF Auto, On, Off On, Off On, Off DHT100/200 USER CONTROLS 3-2-4-1 MAIN MENU The Menu can only be accessed from the Remote Control. 1. Press "Setup" button to show the main menu on screen 2. Press "Right" or "Left" button to select the item you want. 3. Press "Enter" button to enter the sub-menu. 4. Press "Up" button to return the main menu 5. Press "Setup" button to exit the menu 3-2-4-2 DRAWING 57 LANGUAGE 㪦㪪㪛 㪤㪼㫅㫌 㪪㪼㫃㪼㪺㫋㫊㩷㫋㪿㪼㩷㪣㪸㫅㪾㫌㪸㪾㪼㩷㫆㪽㩷㪦㪪㪛㩷㪤㪼㫅㫌㪅 㩿㪜㫅㪾㫃㫀㫊㪿㪃㩷◲㜚ਛᢥ㪃 ❥㜚ਛᢥ㪃 㪝㫉㪸㫅㪺㪸㫀㫊㪃㩷ᣣᧄ⺆㪃 㪛㪼㫌㫋㫊㪺㪿㪃㩷 㪪㫇㪸㫅㫀㫊㪿㪀 㪪㫌㪹㫋㫀㫋㫃㪼 㪪㪼㫃㪼㪺㫋㫊㩷㫋㪿㪼㩷㪣㪸㫅㪾㫌㪸㪾㪼㩷㫆㪽㩷㫊㫌㪹㫋㫀㫋㫃㪼㪅 㩿㪜㫅㪾㫃㫀㫊㪿㪃㩷◲㜚ਛᢥ㪃㩷❥㜚ਛᢥ㪃㩷㪝㫉㪸㫅㪺㪸㫀㫊㪃㩷ᣣᧄ⺆㪃㩷㪘㫌㫋㫆㪃㩷㪦㪽㪽㪀 㪘㫌㪻㫀㫆 㪪㪼㫃㪼㪺㫋㫊㩷㫋㪿㪼㩷㪣㪸㫅㪾㫌㪸㪾㪼㩷㫆㪽㩷㪻㫌㪹㪅 㩿㪜㫅㪾㫃㫀㫊㪿㪃㩷◲㜚ਛᢥ㪃㩷❥㜚ਛᢥ㪃㩷㪝㫉㪸㫅㪺㪸㫀㫊㪃㩷ᣣᧄ⺆㪃㩷㪛㪼㫌㫋㫊㪺㪿㪃㩷 㪪㫇㪸㫅㫀㫊㪿㪀 DHT100/200 DRAWING 58 㪛㪭㪛㩷㪤㪼㫅㫌 㪪㪼㫃㪼㪺㫋㫊㩷㫋㪿㪼㩷㪣㪸㫅㪾㫌㪸㪾㪼㩷㫆㪽㩷㪛㪭㪛㩷㪤㪼㫅㫌㪅 㩿㪜㫅㪾㫃㫀㫊㪿㪃㩷◲㜚ਛᢥ㪃㩷❥㜚ਛᢥ㪃㩷㪝㫉㪸㫅㪺㪸㫀㫊㪃㩷ᣣᧄ⺆㪃㩷㪛㪼㫌㫋㫊㪺㪿㪃㩷 㪪㫇㪸㫅㫀㫊㪿㪀 USER CONTROLS 3-2-4-3 VIDEO TV Shape There are two aspect ratios to choose from: 4:3: The image will be displayed in 4:3 aspect. 16:9: The image will be displayed in 16:9 wide screen. TV System Selects system you need. DRAWING 59 3-2-4-4 AUDIO 1 AC3, DTS, MP3/WMA, Others: Analog Out:Selects the channels you need (2 or 6 channels) Digital Out: PCM, RAW, OFF RAW: Digital output PCM: Analog output Please set 2 channels and PCM when playing wireless stereo speaker. DRAWING 60 DHT100/200 USER CONTROLS 3-2-4-5 AUDIO 2 Prologic: Auto: Default setting. The DVD player will automatically change the output from 2 channels to 6 channels. On: Sets the function always on. Off: Sets the function off. Subwoofer: On: Sets the subwoofer on. Off: Sets the subwoofer off. Factory Set: On: Restores the default setting. Off: Keeps the user ' s setting. DHT100/200 DRAWING 61 4. APPENDICES 4-1 1. TROUBLESHOOTING No Images appears Check the power cable connection at the power inlet of the projector and at the wall outlet. Confirm that the main power switch at the rear of the projector is in the on position. Check the Standby/on button indicator. (Section 3-1) Confirm that the lens cap has been removed. Make sure the source device is properly connected to the projector, and is outputing a signal. Press "Source" button on either the projector or the Remote Control to ensure that correct source is selected. 2. Image is blurred Ensure the distance between the projector and the screen is within the focus range of the lens. (Section 2-2) Adjust the focus ring. 3. Image is too dark Adjust the contrast or brightness in the image menu of projector properly. Adjust the brightness in the setup menu of DVD player. Has the lamp reached the end of its life? If so replace the lamp. 4. Computer Image is unstable or the projector isn't projecting the whole image. Press "SYNC" button either on the projector or the Remote Control to synchronize the computer output signal. Use "Image" menu to adjust the tracking or frequency. Verify that the computer's output resolution to the projector is less than or equal to 1024 x 768. 5. Image is stretched when displaying 16:9 DVD. Adjust the "Aspect Ratio" in the OSD of projector. Adjust the "TV Shape" in the OSD of DVD player. DHT100/200 APPENDICES 6. No sound Make sure the Mute option in Audio menu is off. Make sure the Audio menu in DVD player's OSD is set properly. Make sure the Internal/External speaker option in audio menu is set as required. Make sure the channel of wireless transmitter selected in projector is the same as the channel of wireless receiver selected in the wireless speaker. 7. Wireless speaker noisy Change the channels on the projector and wireless speaker simultaneously. There are 8 channels selectable.(refer to the Section 3-2-2-4) 8. Remote control does not work Install new batteries. Make sure there are no obstacles between you and the projector's receivers. Make sure you are attempting to operate it within its usable range. 9. Can't read the memory card Make sure the Media Player's LED indicator (beside the card slot) is lighting.. Check the compatibility of memory card (refer to section 2-3-2) Re-insert the memory card. 10. Can't play DVD Make sure the DVD player's LED indicator (on the control panel of the projector) is lighting Confirm that the disc is an original edition. Eject the disc and play again. 11. The disc can't play or is automatically ejected after loading Make sure the disc is free from dirt and dust and is not damaged. Make sure the disc is loaded with the label side face-up and aligned properly in the disc tray guide. Make sure the disc format is compatible with the DVD player of the projector. Please refer to the specification. 12. The color of Image is not correct DHT100/200 Please reset all settings. APPENDICES 4-2 4-2-1 MAINTENANCE REPLACING THE LAMP When the lamp's total working time accumulates to over 1850 hours, the on-screen display (OSD) will deliver a message recommending that you replace the lamp. Please contact a service center to replace the lamp as soon as possible, or refer to the following instructions to replace it yourself. TO REPLACE THE LAMP 1. Turn off the projector by pressing the "Power" button 2. Allow the projector to cool down for at least one hour. 3. Switch off the power and disconnect the power cord. 4. Loosen the screw on the lamp cover and remove the lamp cover. (Drawing 62) 5. Loosen two screws on the lamp module (Drawing 63) remove the lamp module by pulling on the handle (Drawing 64) 6. Insert a new lamp module (Drawing 65) into the socket: make sure it is in position. 7. Reverse steps 4 and 5 8. Ensure that the lamp cover is securely attached and flush with the bottom of the unit. The unit will not operate with the cover incorrectly installed. 9. Reset the lamp timer DRAWING 62 DRAWING 63 DRAWING 64 DRAWING65 DHT100/200 APPENDICES To reset the lamp timer 1. Press the Menu button on control panel or remote controller. 2. Go into the system menu and move the cursor to the lamp reset item. 3. Select "Yes" to execute the lamp reset and the lamp hours will reset to 0 hour. DRAWING 66 Important * Do not touch the lamp immediately after it has been used: it will be extremely hot. Allow the fan to finish its cooling process, then turn the projector off, and disconnect the power cord. Then allow at least one hour for the lamp to cool down before handling. * Do not remove any screws other than the lamp cover screw and the lamp housing screws. Removing other screws could result in electric shock. * Although the mercury content of the lamp is minuscule, spent lamps should be treated as hazardous waste. Consult federal, state/provincial or local regulations for proper disposal. CAUTION Continuing to use the lamp after the replace the lamp message has been displayed on the screen may result in the lamp exploding. If this occurs, pieces of glass may scatter inside the projector, and out into the room. If this occurs, do not touch them, as the pieces of glass may cause injury. The bulb contains a small amount of mercury: ventilate the area well. Contact your dealer for servicing: do not attempt to service the DHT100/200 projector yourself. APPENDICES 4-2-2 CLEANING THE PROJECTOR Cleaning the cabinet Wipe lightly with a soft, dry cloth. If the cabinet is very dirty, clean it with a soft, dampened cloth using mild commercial cleaner and finish with a dry cloth. Do not use liquid or aerosol cleaners. Cleaning the lens Clean the lens carefully by using a blower or lens paper to prevent creating any scratches on lens. DHT100/200 APPENDICES SPECIFICATION Color system Computer compatibility Screen size (diagonal) Throw distance Brightness Contrast ratio DMD panel Color wheel Number of pixels Horizontal resolution Projection lens Lens shift (U/D ratio) Projection lamp Digital Zoom Digital Keystone Picture Reverse Scan Front Elevation / Maximum tilt angle NTSC/PAL/SECAM/NTSC4.43 SXGA (Compression) /XGA/SVGA/VGA/Mac Adjustable from 35” to 300” 1.5m – 10m 1800 ANSI lumens 2000 : 1 Single 0.7” DDR XGA DMD 4 segmentations 786,432 (1024 x 768) 480 TV Lines (S-Video) F2.8~ 3.1, f = 25.8 ~ 30 mm, Zoom ratio: 1.2:1 10 : 0 250 W, Lamp life: 2000 hours (Normal mode) / 3500 hours (Eco mode) Max. X32 for XGA mode +/- 12 degrees (Vertical) Left/Right and Top/Bottom Up to 15 degrees / 45 degrees up and down Scanning frequency Automatic frequency control H sync. 15kHz~82kHz, V sync. 50Hz~85Hz 5°C to +35° 32dBA Dsub 15 x1 Dsub 15 x1 Operating temperature Fan noise Computer Input Computer Output Video Audio Out Built-in Speaker Wireless Speaker Power Supply Power consumption Dimensions (WxDxH) Net weight Regulations Standard Accessories Optional Accessories DHT100/200 Component (HDTV, EDTV) input: RCA Jack x3, RCA x1 (Composite), Mini DIN 4-pin x1, RCA x2 (R, L-mono) 3.5mm mini Jack x 1: Audio Out 3.5mm mini Jack x 3: Audio 5.1 channel output 2W x 1 Stereo 25W x 2 Dimension (WxDxH): 170x180x270 mm(6.7" x 7.1" x 10.6") Weight: 8.35 Kg 100 - 240V, 50 - 60Hz 330W 374 x 290 x 92mm (14.7" x 11.4" x 3.6") 4.5 kg (10 lb) 1. EMC - FCC Class B, CE Class B, CCC 2. Safety - cUL, TUV, CB Power cord VGA Cable Audio Cable Mac Adapter Remote Control Soft Carry Bag for projector 25W x 2 Wireless speakers TV tuner Deluxe speaker Satellite speaker Soft Carry Case for Wireless Speakers 4-3 ALL-IN-ONE PROJECTOR MODEL DHT100/200 OWNER'S MANUAL Meiloon Industrial Co., Ltd.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2004:04:26 12:26:23-07:00 Create Date : 2004:04:26 12:25:52-07:00 Title : DHT100 UserMan.pdf Author : choque Creator : PScript5.dll Version 5.2 Producer : Acrobat Distiller 5.0.5 (Windows) Page Count : 26 Mod Date : 2004:04:26 12:26:23-07:00 Creation Date : 2004:04:26 12:25:52-07:00 Metadata Date : 2004:04:26 12:26:23-07:00EXIF Metadata provided by EXIF.tools