MUL T LOCK TECHNOLOGIES ENTRRC00 ENTR Remote Control User Manual ENTRR Fingerprint Reader FCC IC

Download:
Mirror Download [FCC.gov]
Document ID	3259986
Application ID	dsinfhCdOsdcnM1Djuvp8Q==
Document Description	Users Manual-Part 2 (21-35).pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	308.67kB (3858367 bits)
Date Submitted	2017-01-16 00:00:00
Date Available	2017-07-15 00:00:00
Creation Date	2016-12-28 10:54:59
Producing Software	PDF-XChange Viewer [Version: 2.0 (Build 40.7) (Nov 25 2008; 17:31:42)]
Document Lastmod	2016-12-28 13:42:35
Document Title	ENTRR Fingerprint Reader_user manual_FCC,IC.pdf
Document Creator	PDFCreator Version 1.2.3
Document Author:	suhsiao

Y I ENTR‘ I
.MUL-T-Locx'
mm; mm
5. Touchpad Reader Operation
5.1 Operation
To turn the Touchpad Reader 0N press [it] for 5 seconds. The reader will perform a
self test followed by series of beeps. LED blinks Green, Red, Blue.
5.2 Pairing Touchpad Reader
This procedure is done via the ENTR® lock. See also: Pairing Remote Control.
1 III‘ 2 ill. 3
Touch ENTR' lock screen with palm Press [Add] Numeric buttons illuminated.
or fingers for 3 seconds to active, Type [PIN code] ill‘ [it]
Numeric buttons blinking.
Mute Cig Del Mute qu Flute f :i 1 ,1 [‘el
1 2 3 1 2 3
4 5 #
tiude d
4’ 51? yr
4 In» 5
Press [1] to add Touchpad. Touch the Touchpad Reader screen
illuminated buttons turn off. with palm or fingers.
[OK] indication blinks for 15 seconds Press [711iiiQm
waiting for the Touchpad. Blue LED blinking rapidly.
Mute Cfg Lei
22 ENTR® Dead Bolt User Manual
I, MUL-T-LDCK‘
I ENTR' I
mm; mm
Pairing OK
Pairing failed
[0K] indication blinks once,
2 short beeps emitted.
Touchpad Reader added.
I‘Iv-i—: Cfg [,4
OK] indication blinks for 15 seconds,
No beeps emitted.
In wall reader: Green LED Illuminated
and 2 beeps emitted.
Start the process from Stage 1.
I Hang the Touchpad Reader on the base plate.
I Tighten fixing screw.
Fixing screw
ENTR® Dead Bolt User Manual
23
Y I ENTR’ I
aMuL-T-LDCK‘
mm; mm
5.3 Touchpad Reader Master PIN Code
1 III’ 2 III. 3
Touch screen with palm or fingers. Enter [New master PIN code] Reenter:
Press [11] in. [ll] (440 digits) lIIQ [a] [New master PIN code] lIIQ [ll]
For Example:1231234#
Master PIN code added Master PIN code not added
Green [OK] illuminated for 1 second. Red [Error] illumlnated for 1 second.
2 short beeps emltted. 1 long beep emltted.
5.4 Menu Mode
Entering menu mode: Press [*] n. [Master PIN code] n. [#1
5.5 Adding PIN Code (up to 20 different codes)
1 III‘ 2 III» 3
Touch Reader screen with palm Enter [Personal PIN code] Retype;
or fingers [440 dlglts) u» [at] [Personal PIN code] an [ll]
Press [*1 III. [Master PIN code] For example: 123123491
up [a]
Press [11] III’ [II]
PIN code added PIN code not added
Green [0K] illuminated for 1 second, Red [Error] illumlneted for 1 second,
2 short beeps emitted 1 long beep emitted.
24 ENTR® Dead Bolt User Manual
Y I ENTR‘ I
.MUL-T-ann'
mm; mm
5.6 Open Door
1 l» 2
Touch Reader screen wuh palm or fingers. Press [Personal pm code] in’ [3] Red [Error] illuminated for 1 second,
1 long beep emitted.
5.7 Lock Door
1 III‘ 2 Not locking
Touch Reader screen with palm or fingers. press [1] r..‘ [a] Red [Error] illuminated for 1 second,
1 long beep emitted
5.8 Delete PIN Code
1 HQ 2
Touch Reader screen with palm or fingers. For delen'on enter:
Press [*1 III’ [Master PIN code] III’ [:1] [Personal PIN code] rrlQ [tr]
Press [as] in. [u]
Personal code deleted Personal code not deleted
Green [OK] illuminated for 1 second, Red [Error] illumlnated for 1 second,
2 short beeps emitted. 1 long beep emitted.
5.9 Delete all PIN Codes
1 ”IQ 2
Touch Reader screen WIth palm or fingers. Enter [Masfier PIN code] ill‘ [:1]
Press [*1 n» [Master PIN code] n» [It] Reamer; [Master pm code] rer [3:]
Press [22] lll‘ [“1
Personal PIN codes deleted Personal PIN codes not deleted
Green [0K] illuminated for 1 second, Red [Error] illuminated for 1 second,
2 short beeps emitted, 1 long beep emitted.
Note: Master PIN code can not be deleted.
ENTR® Dead Bolt User Manual 25
In MUL-T-LDCK'
5.10 Volume Control
1 ”IQ 2
I ENTR‘ I
«mm mm
Touch Reader screen With palm or fingers. Press [2] to increase the volume, or [B] to
press [*1er [Master pm Code] in [a] decrease the volume
press [55] in. [k] press [a] to confirm volume level.
5.11 Factory Reset
The reset action will delete a_H PIN codes (master and personal) and will cut off the
Touchpad Reader from the ENTR® lock.
1 ”IQ 2
Touch Reader screen with palm or fingers. Enrer [Master PIN code] in. [a]
press [*1 n. [Master PIN code] nr. [3:]
press [as] in. [k]
Personal and master PIN
codes deleted
Personal and master PIN
codes not deleted
Green [0K] illuminated for 1 second.
2 short beeps emitted.
Device performing self test & Is factory reset.
Red [Error] illuminated for 1 second.
1 long been emitted.
26
ENTR® Dead Bolt User Manual
Y I ENTR‘ I
.MUL-T-ann' m.
6. Fingerprint Reader
6.1 Mounting the Fingerprint Reader
Prior to starting, select the location where
the Fingerprint Reader is to be mounted.
Avoid direct sun light to the front panel.
- Attach the Fingerprint Reader base plate
to the wall.
0 Use 4 screws and screw anchors or
double sided glued tape.
6.2 Battery Replacement
1. Using a 2mm Allen key release the lid
screw and open the lid.
2. Insert batteries (2xAA) according to the m
"+" "-" signs. Green LED will illuminate U
for 2 seconds. :
3. Close the lid and tighten the screw.
4. Press [#] for 5 seconds. a
The reader will self calibrate, which will be followed Li "
by a series of beeps and blinking LEDs.
6.3 Adjust Date & Time
DEVICE --I--I-- - - 24/09/16
DATE/TIME i|lil
DD/MMIYY : 11:00
Enter Date Enter Time Press [OK]
Press [OK] Press [OK]
ENTR® Dead Bolt User Manual 27
Y I ENTR‘ I
EMUL-T-LDCK'
«mm mm
6.4 Pairing Fingerprint Reader
This procedure is done via the ENTR® lock.
See also: Pairing Touchpad Reader.
1 In» 2 lll‘ 3
Touch ENTR‘ lock screen with palm Press [Add] Numeric buttons illuminated.
or fingers for 3 seconds to active Type [PIN code] lll‘ [it]
Numeric buttons blinking,
Mule Gig Del
Mule Gig
4 HQ 5
Press [11m add the reader Touch Flngerprlm Reader screen.
llluminaled buttons turn Off, 2 Short beeps emitted.
[OK] indication blinks for 15 seconds Press [OK] for YES or [*] to cancel.
waiting for the reader
Ii-Ih Cfg i—‘l PAIR LOCK?
| 5. '
4| = : *-NO OK-YES
i. I II.» . ll
ll [l | [I
a v a e r
Pairing 0K Pairing failed
0K] Indication bllnks once 1 “”3 PEEP emitted.
2 short beeps emitted. Red LED illuminated for 2 seconds.
Fingerprint Reader added.
LOCK FAILED
PAIR PAIR
Note: At the end of the initial pairing process,
a short notice will be displayed.
28 ENTR® Dead Bolt User Manual
? I ENTR‘ I
.MUL-T-ann' my... .me
6.4.1 Add Master User
Setting a Master User requires both fingerprint and PIN code. It is possible to have up to
two Master Users.
MASTERNAME
Q)
JOHN
Type in [Master name] Ill. [OK]
6.4.2 Set Finger
Blue LED Illumlnates. Green LED blinking.
SUCCESS
1ST FINGER
ADD USER
SET FINGER
1ST FINGER
Press [OK] Place finger on scanner, wait
for beep, then swipe finger
down several times over
fingerprint scanner until two
Confirmation beeps emitted.
Green LED bllflklflg.
SWIPE
2nd FINGER
SUCCESS
2nd FINGER
Place finger on scanner, wait
for beep, then swme finger
down several times over
fingerprint scanner until two
confirmation beeps emitted.
6.4.3 Set PIN Code
Type in [PIN Code], (4 to 10 digits) Retype [PIN Code]
ADD USER ENTER CODE RETYPE CODE
SET CODE my,“ my,“
4-10 digits 4-10 digits
Press [OK] Press [on] Press [ox]
Matched Codes Mismatched Codes
SUCCESS FAILED
@ A
SET CODE INVALID
ENTR® Dead Bolt User Manual 29
Y I ENTR‘ I
.MUL-T-ann'
mm; “er:
- Hang the reader on the base plate.
- Tighten fixing screw.
Fixingscrew . I
6.5 Unlock the Door
OPTION 1: OPTION 2:
Place finger on fingerprint scanner. Touch the Fingerprint Touchpad.
Short beep emitted & white LED is on. Screen shows user code.
Swipe finger overfingerprint scanner Enter your code uIQ [0K]
Fingerprint authorized: Blue LED blinking
and unlock command is sent.
Fingerprint not authorixed: Red LED is ON.
The device goes to standby.
USER CODE
23:49 03/01
FAILED
Note: In case ENTR® lock hasn’t succeed to unlock the door,
unlock failed message appear on the screen.
UNLOCK
3° ENTR® Dead Bolt User Manual
Y I ENTR’ I
,MUL-T-Locw
mm mm
6.6 Lock the Door
Touch the Fingerprint Touchpad.
Press [1] m [tr]
6.7 Low Battery Indication
Warning signal blinking.
Fingerprint Reader low battery indication
Red LED illuminate for 15 after wake-up,
2 long beeps emitted.
l]
G]
BATTERY LOW
15 2.3: 35;; ,‘
m 5.“ on? j‘
5 7m 8;“; ,
6.8 Setting Menu
USER CODE MASTER CODE [SETTING
Touch screen ”I‘ mm 1- USERS
23:49 03/01 23:49 03/01
Press [*1 Enter [Master PIN code] lll‘ [OK] or
Swlpe finger over fingerprint scanner
ENTR® Dead Bolt User Manual 31
Y I ENTR‘ I
.MUL-T-ann'
«mm IErKEE
6.9 Add User
The unit allows adding up to 20 users. For each user two different fingerprints and
one PIN code. Use different user name for each user.
’SETTING S USERS 2nd MASTER? USERNAME USER #08
& USERS ADD USER A JENNIFER @
*-NO OK-YES JENNIFER
Vress [0K] Press [OK] Choose [OK] to add 2nd User name added. Type [USER NAME]
Master User or[*]to ir|.[OK]
adda user.
Note: This screen Will not
appear if two Master Users
are defined.
5 6 lst finger added 7
USERNAME ADD USER SWIPE SUCCESS SWIPE
SET FINGER E Q) fl
1ST FINGER 1ST FINGER 2"d FINGER
Same user name. Press [OK] to set a finger Swrpe lst finger several SWipe 2nd finger several
Choose different user or use [3'] or [2A] in times over fingerprint times over fingerprint
name. order to set a code only. scanner until two scanner until two
confirmation beeps emitted. confirmation beeps emitted.
2nd finger added 8 9 10
SUCCESS ADD USER ENTER CODE RETYPE CODE
Q) s—ET CODE
2"“ FINGER "-NO OK-YES 4-10 digits 4-10 digits
Press [OK] for v5 or [is] Type [cone] in» [OK] Retype [cone] in. [OK]
for NO.
Mismatched
Matched codes
codes
SUCCESS
Q)
FAILED
INVALID
SET CODE
Process did not complete.
Ail data typed in will be
erased from memory.
32 ENTR® Dead Bolt User Manual
Y I ENTR’ I
.IIIIUL-T-Loclr
mm; .mse
6.10 Delete User
USER CODE MASTER CODE [SETTING
Touch screen III‘ mm
23:49 03/01 23:49 03/01
Press [*1 Enter [Master PIN Code] rm [OK] or
swipe finger over fingerprint scanner
1 2
[SETTING .1 USERS DELETE USER DELETED
.1 USERS DELETE USER JENNIFER A A
‘-NO OK-YES *-NO OK-YES JENNIFER
Press [OK] Use [8V ] or [2‘] to Press [OK] Confirm deletion. Two beeps emitted,
select user for/deletion: Green LED Illuminates.
[DELETE USER] ”IQ [OK]
Note: The first Master User can't be deleted without doing a factory reset.
6.11 Enable/Disable User
USER CODE MASTER CODE [SETTING
Touch screen III» mm
23:49 03/01 23:49 03/01
Press [*1 Enter [Master PIN Code] III. [OK] or
swipe finger over fingerprini scanner.
1 2 3
[SETTING .1 USERS ENABLE USER
.1 USERS ENABLE USER JENNIFER
Disabled ENABLED
Press [OK] Use [Svloru‘ho Use [8'] or [2‘]to Two beeps emitted.
select user: toggle between Users. Green LED Illuminales.
[ENABLE USER] In. [UK] Press [OK]
Note: Repeat this procedure to disable a user.
ENTR® Dead Bolt User Manual 33
Y I ENTR‘ I
.MUL-T-ann'
mm; mm
6.12 Delete All Users
USER CODE MASTER CODE [SETTING
Touch screen III» ****** Ill» .1 USERS
23:49 03/01 23:49 03/01
Press [*1 Enter [Master PIN Code] r... [UK] or
swipe finger over fingerprint scanner.
[SETTING .1 USERS DELETE ALL? SUCCESS
.1 USERS DELETE ALL A A @
*-NO OK-YES *-NO OK-YES DELETED ALL
Press [OK] Use [8'] or [2‘] to Press [OK] Press [OK] Two beeps emitted.
select: Green LED illuminates.
[DELETE ALL] ill. [OK]
6.13 Add Time Schedule
1 2 3 4 5
[SETTING .1 USERS ADD SCHED CHOOSE DAY SUNDAY
J. USERS ADD SCHED SARAH [‘ FROM
Sun-Sat(1-7) 12:00
Press [OK] Use [3V] or [2A] to Use [3'] or [2A] to Press 1-7 m choose a day. Entersmmfimem. [on
select: select a user m. [0K] Example: 1 for Sunday.
[ADD SCHED] ”IQ [OK]
6 7
SUNDAY
12:00-13:00
*-No OK-YeS
Schedule
Q)
Enter END time Iil’ [OK] Press [OK] for YES or [*1
for NO
Notes:
1. Define up to 7 different time schedules for the same user.
2. Press [*] to go back on every menu.
3. Press [*] for 3 seconds to exit setting menu.
34 ENTR® Dead Bolt User Manual
Y I ENTR’ I
.MUL-T-Locw
mm; mm
6.14 Edit Time Schedule
1 2 3 4 5
[SETTING S USERS EDIT SCHED SUNDAY FRIDAY
& USERS EDIT SCHED SARAH 12:00-13:00 12. 0-13100
*-Back OK-Yes V DAY A
Press [OK] Use [3V1er[2A1te Use [3V1or12A1ro Use [3V1or12A1ro Use [8V1ar[2A1te
select: toggle between users choose the desired change schedule day
[EDIT SCHED] Ill‘ [OK] ru¢10i<1 schedule to be edited. n. [0K]
Presslng on [44] for
3 seconds shall delete
the specific schedule.
6 7 8 9
FRIDAY FRIDAY FRIDAY FRIDAY FRIDAY
11:00-13:00 12:15-13:00 12:15-17:00 12:15-17:45 12:15-17:45
--:mm'HH:MM HH:--'HH:mm HH:mm'--:mm HH:mm'HH:—- *-NO OK-Yes
UseiaV]or[zA1te Use [sVlorizAne Use [s']or[zA]to Usels'lmlelto Press [OK]forVESor[*]
change the START hour change START minutes change END hour setting. change END mlnutes for N0.
settrng. Use [6 >1 to move settlng. Use [6 >1 to move Use [6 >1 to move to the setting.
to START minutes, to the END hour, END minutes,
6.15 Volume Control
USER CODE MASTER CODE [SETTING
Touch screen |ll¢ mm .1 USERS
23:49 03/01 23:49 03/01
Press [*1 Enter [Master pm Code] rm [ox] or
SWIpe finger over fingerprint scanner.
1 2 3
[SETTING g DEVICE VOLUME VOLUME SUCCESS
§ DEVICE VOLUME @
SET VOLUME
Use [3'] m [2A1te Use [8V] or [2‘] to Use [3V] or [2A1to Press [OK] Two beeps emltted.
select: select: toggle between HIGH, Green LED illuminates.
[DEVICE] Ill’ [OK] [VOLUME] lll‘ [0K] MEDIUM or LOW.
ENTR® Dead Bolt User Manual 35
Y I ENTR‘ I
.MUL-T-ann'
mm; Inns:
6.16 Double Security
After activating the double security option use both methods - swiping a fingerprint
and inserting a PIN code to unlock the door.
Note: User set up with only one of the settings (fingerprint or PIN code) will not be
able to unlock the door.
USER CODE MASTER CODE [SETTING
Touch screen III» mm
23:49 03/01 23:49 03/01
Press [*1 Enter [Master PIN Code] iii. [OK] or
swipe finger over fingerprint scanner.
1 2 3 4
,SETTING n DEVICE ENABLE? 2X Security
g DEVICE 2x Security @
‘-N0 OK-YES 0N
Use [3'] or [2‘] to Use [8'] or [2‘] to Press [OK] Two beeps emitted.
select: select: Green LED illuminates.
[DEVICE] iiiQ [OK] [211 Security] iiiQ [UK]
6.17 Factory Reset
Warning: A factory reset action will delete all information stored in the memory,
including users and paired locks.
USER CODE MASTER CODE [SETTING
Touch screen Ill» ****** In» .1 USERS
23:49 03/01 23:49 03/01
Press [*1 Enter [Master PIN Code] iii. [OK] or
swipe finger over fingerprint scanner.
[SETTING § DEVICE RESET? SUCCESS
— —_ x;
g DEVICE FACTORY c A @
*-N0 OK-YES *-NO OK-YES FACTORY 0
Use [3'] or an to Use [3V] or [2A] in Press [ox] Press [OK] Two beeps emitted.
select: select: Green LED illuminates,
[DEVICE] Ill. [OK] [FACTORY] ill. [OK]
35 ENTR® Dead Bolt User Manual

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2016:12:28 13:42:35+08:00
Create Date                     : 2016:12:28 10:54:59+08:00
Metadata Date                   : 2016:12:28 13:42:35+08:00
Creator Tool                    : PDFCreator Version 1.2.3
Format                          : application/pdf
Title                           : ENTRR Fingerprint Reader_user manual_FCC,IC.pdf
Creator                         : suhsiao
Document ID                     : uuid:6f5480a7-a843-4008-8969-4a00ae265f2d
Instance ID                     : uuid:c769ce65-1ef8-4e66-866d-dc2be77488eb
Producer                        : PDF-XChange Viewer [Version: 2.0 (Build 40.7) (Nov 25 2008; 17:31:42)]
Page Count                      : 15
Author                          : suhsiao

EXIF Metadata provided by EXIF.tools