Macro Image Technology MDP-130 HDTV Receiving PC Card User Manual DTV
Macro Image Technology, Inc HDTV Receiving PC Card Users Manual DTV
Contents
- 1. Users Manual DTV
- 2. Users Manual DVI
Users Manual DTV
FCC RF INTERFERENCE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio, TV technical for help. Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment, To achieve optimum performance of the MyHD Board, your PC requires a following minimum configuration. CPU : Pentium-II 333MHz or faster DRAM : 64 Megabytes or more System Bus : PCI OS : Windows 98SE, Windows ME , Windows 2000, Windows XP Other Software : DirectX Media 7.0 or Higher Graphic Card : DirectX compatible VGA card(8 MB memory or more recommended) One Available PCI Slot One 9-pin serial port *For digital transport stream(ATSC) recording and playback, minimum system requirements are as follows: CPU : Pentium-III 800MHz or faster All the other requirements are the same as the above configuration. This package is including : - MyHD PCI Card - Quick Installation Guide - VGA Loop through Cable with External A/V Connector - Remote Control Handset - Remote Control Receiver - Installation CD - Audio Card Jumper Cable - Two 1.5V AAA Batteries To install MyHD on your Windows 98SE, Windows ME, Windows 2000, or Windows XP system: Turn off your PC, install the MyHD PCI card, connect the audio jumper cable as needed, and connect the Remote Control Receiver to a serial port on your PC. Connect the MyHD PCI card to an external video source and display devices as desired. Turn on your PC and install the MyHD Windows device driver from the installation CD, then install the MyHD application software. If DirectX 7.0 or higher version is not installed on your PC, install the latest version of DirectX before the installation of the MyHD device driver. Antenna 1 Recommend to connect the antenna lead from your rooftop antenna Antenna 2 Recommend to connect the antenna lead from your cable antenna A/V Connector Connector to connect A/V cable SPDIF Output Allows the digital audio output of the MyHD card to be connected to an external audio amplifier. Audio Output Allows the analog audio output of the MyHD card to be connected to the LINE IN, AUX or CD input of your PC sound card or motherboard (using the enclosed jumper cable). VIP 1.1 Connector This connector is not currently working. Warning - Static Sensitive Components To avoid possible damage to MyHD Board and/or other system components from static discharge, always discharge your body's static electricity prior to handling MyHD Board or other system components. Discharging can be done either by using a properly grounded anti-static wrist strap or by simply touching the chassis of a grounded (plugged-in) computer. In addition, always handle the card by its edges whenever possible, to avoid mechanical damage to delicate components on the board. To install the MyHD board, follow the steps listed below: 1. With the power off, remove your computer cover and locate an available PCI slot. 2. Remove the screw attached to the slot cover and remove the slot cover plate. 3. Before handling the MyHD card, ground yourself by touching the power supply box inside your computer 4. Position your card directly above the PCI slot and insert the card firmly into the slot. Care should be taken to press it evenly and snugly into its slot. 5. Use the enclosed jumper cable to connect the audio output of the MyHD card to the LINE IN, AUX or CD input of your PC sound card or motherboard. **If the audio output is set by the jumper cable in the MyHD application program, you have to connect the jumper cable between the MyHD card and a sound card. However, you do not need to do it when the audio output is set by wave in the MyHD application program.(Refer to Audio Configuration ). 6. Replace the cover on the computer. 7. Attach the antenna lead from your rooftop antenna or cable system to the antenna input of the MyHD card. 8. Connect the remote control receiver to 9-pin serial port. Choose your display configuration A dual monitor configuration displays the standard Windows desktop on your PC monitor along with full-screen output from your MyHD card on a separate HDTV or VGA monitor. MyHD supports the following resolutions and horizontal frequencies on any monitor equipped with standard RGBHV or YPbPr inputs: - 1080i(1920x1080 interlaced, 33.7kHz) - 1024p(1024x768 progressive, 48.3kHz) - 720p(1280x720 progressive, 44.9kHz) - 480p(720x480 progressive, 31.5kHz) - 480i(720x480 interlaced, 15.75kHz) A single monitor configuration displays the output of your MyHD card in either a resizable window or full-screen(giving you the ability to switch between the regular Windows desktop and MyHD's full-screen display), by using the enclosed VGA loop through cable with external A/V connector as shown(connecting the VGA output of your PC to the MyHD card, which then passes the combined video signals to your PC monitor). You can watch and capture video from any external source (including VCR, DVD, laserdisc, etc.) by connecting them to the VGA loop through cable with external A/V connector. Simply connect the video and audio outputs from your external source to the S-Video and/or RCA input jacks. MyHD also supports SPDIF for digital audio output. Simply connect a digital audio cable from the RCA output jack on the MyHD card to the SPDIF input of any Dolby AC-3 5.1 channel audio amplifier. After your hardware installation has completed, turn on your PC and insert the installation CD. As Windows begins to boot, it will automatically open the "Add New Hardware Wizard" once it detects your addition of the MyHD card: Click on "Next >". Choose "Search for the best driver for your device.(Recommended)" and click on "Next >". Choose "Specify a location" and then click on "Browse" to open the contents of the installation CD, navigate to the DRIVER folder, and choose the subdirectory for the version of Windows currently installed on your computer and click on "Next >". Note: you must choose the driver which matches your operating system as software designed for one version of Windows may not operate properly on another. Click on "Next >" if MyHD driver is searched. Copying Files... After the installation has completed, click on "Finish". To confirm the installing MyHD in device manager, 1. Choose "Control Panel"/"System"/"Device Manager". 2. Click "Sound, video and game controllers" and then confirm the category of "MDP100 Video Capture". Choose; 1. "MDP100 Video Capture Properties" 2. "General" Confirm the phrase of "This device is working properly" in device status. If the phrase is not shown, please install the MyHD device driver again. 1. Choose "Control Panel"/"System"/ "Disk drives" 2. Click "GENERIC IDE DISK...". Choose; 1. "GENERIC IDE DISK...Properties" 2. "Settings" Confirm the "DMA" in options. If the "DMA" is not checked, please check the "DMA". If the monitor is connected to VGA card through VGA loop through cable with external A/V connector, confirm display properties. 1. Choose "Control Panel"/"Display". 2. Choose "Settings"/"Advanced" in display properties. 3. Choose "Monitor" and then uncheck "Automatically detect Plug & Play monitors". Warning Don't change resolution of screen area in "display properties"/"settings" while the MyHD program is executing. You can download new device driver in our homepage(www.DTVsolution.com). 1. Choose "Control Panel"/"System"/"Device Manager". 2. Click "Sound, video and game controllers"and then confirm the category of "MDP100 Video Capture". Choose 1. "MDP100 Video Capture Properties" 2. "Driver" Click on "Update Driver...". As "Update Device Driver Wizard" is displayed, click on "Next >". Choose "Display a list of all the drivers in a specific location, so you can select the driver you want." and click on "Next >". Choose "Show compatible hardware" and then click on "Have Disk..." to browse to the driver folder and click on "Next >". Choose "Show compatible devices" and then click on "Next >". If location of driver is correct, click on "Next >". When the installation is complete, click on "Finish." After your hardware installation has completed, turn on your PC and insert the installation CD. As Windows begins to boot, it will automatically open the "Found New Hardware Wizard" once it detects your addition of the MyHD card: Choose "Install from a list or specific location (Advanced)" and click on "Next >". Choose "Search for the best driver in these locations" and "Include this location in the search," then click on "Browse" to open the contents of the installation CD, navigate to the DRIVER folder, and choose the subdirectory for the version of Windows currently installed on your computer and click on "Next >". Note: you must choose the driver which matches your operating system as software designed for one version of Windows may not operate properly on another. Click on "Next >" to install the driver. Next massage box can appear while installing the driver. Since its not a setup error, Press Continue Anyway button. After the installation has completed, click on "Finish". To confirm the installing MyHD in device manager, 1. Choose "Control Panel"/"System/"Device Manager". 2. Click "Sound, video and game controllers" then confirm the category of "MDP100 Video Capture". Choose; 1. "MDP100 Video Capture Properties" 2. "General" Confirm the phrase of "This device is working properly" in device status. If the phrase is not shown, please install the MyHD device driver again. To confirm the DMA settings. DMA is default "Transfer Mode" in Windows XP, 1. Choose "Control Panel"/"System" /"Device Manager". 2. Select "IDE ATA/ATAPI Controllers"/"Primary IDE Channel". 3. Click "Advanced Settings" then, confirm DMA is selected in "Transfer Mode". With the installation CD still loaded in your PC, open the Windows Explorer, navigate to the APP folder on the CD, and double-click on SETUP.EXE to launch the software installation, following the on-screen prompts until installation is completed. Click on "Next >". Choose Destination Folder, click on "Next >". Choose a program folder, click on "Next >". Installation process starts. Installation of the program is completed, then click on "Next >". After the installation has completed, click on "Finish". To run the MyHD program immediately, check the check box and click on "Finish". The below window will be appeared when you execute the MyHD program. Overlay window for watching TV Press mouse right button on MyHD application program. Pop-up menu will appear like this. antenna1 (Ctrl+1) : Change input to antenna 1 antenna2 (Ctrl+2) : Change input to antenna2 Favorite (Shift+M) : Favorite channel mode on Composite(Ctrl+V) : Change input to Composite. S-Video(Shift+V) : Change input to S-Video. File (Ctrl+F) : File play mode on. When this menu is selected, Active Channel changes to Active File and Channel List changes to File List in the menu. DVD (Shift+D): DVD input mode. Sub-menu(Move, Audio, and Sbutitle) will be displayed on the "Pop-up menu" if DVD input is selected. Tape (Ctrl+D) : Record and playback with AV/C Tape Recorder through IEEE 1394 interface. Active channel : As shown on the right, current active channel is shown. Select one of them, then channel will change what you select. Channel list (Ctrl+L) : Execute channel list configuration window. ( refer to channel settings) Active File : As shown on the right, file that is in the file list is shown. Select one of them, you will play the file you selected. File List (Ctrl+L) : Execute File list dialog box. (refer to file play setup) Move, Audio and Subtitle menu, as shown below, will be display when you open the "pop-up menu" if DVD input mode is selected. Move : Select and play new DVD title. Audio(Ctrl + A) :Select an Audio Type or a Language that you want to play. Subtitle(Ctrl + T) Select a Subtitle to play. Pause/Play : Selecting Pause will pause current display. The letter on menu now switches to Play. Selecting Play will play the paused display. then, the letter on menu switches back to Pause. Stop : Stop display Channel_Up (UpArrow) : Change channel up Channel_Down (DownArrow) : Change channel down Hide Control Panel: Hide control panel. If control panel does not displayed on the screen by pressing Hide Control Panel, Hide Control Panel changes to Show Control Panel. If you select Show Control Panel, then the control panel hidden by pressing Hide Control Panel will show up. HD mode(Ctrl+H) : Change to Full Screen Mode. Capture (Ctrl+C) : Start capturing stream, moving picture or image as referred to configure Add Reservation : Show Add Reservation dialogue . (refer to Capture settings ) Config panel (Ctrl+P) : Execute environment configure window. (refer to AV settings) Exit Program (Ctrl+X) : Exit MyHD About MyHD : Shows program information . MyIRC is the control program of MyHD through inputs of Remote Control Signal. Right State Do not use IR receiver state Error State MyIRC supports the functions of Remote Control and some functions of " Reservation Capture". MyIRC must be executed to run the automatic execution of MyHD and changeover to suspend mode automatically. The "Reservation Capture" can be executed even though the Remote Control Receiver is not connected. If error is occurred on the Remote Control Receiver, please exit the MyIRC program, then reconnect the receiver correctly and run Config MyIRC dialogue. When you click right mouse button that is pointing MyIRC icon, the above pop-up menu will be displayed. When you select Reservation Capture Information on the pop-up menu, Reservation Capture Information is shown. Please set up the reservation capture function in "Config Panel/Capture Settings/Reservation Capture Option. ”(refer to Capture Settings) MyIRC supports the learning function for an external remote controller. It means you can use your remote controller of TV or VTR to execute the MyHD program and add "hot keys" on unused buttons of the MyHD's Remote Control Handset. ? GDo not use IR recevier :MyIRC program does not use IR fumction. It only support reservation capture function. ? GDo not use MyHD remote controller : Decide whether to use the MyHD's remote control handset. When it is not selected, button operation of MyHD remote control are not related to Learning External Remote controller . When Do not use MyHD remote controller selected, MyHD remote controller won't work anymore. Button operation of external remote controller can now be learned. ? GUse external remote controller ; Decide to use another remote controller - Learning external remote controller (1) Click the right mouse button on the icon of MyIRC, then select "Config MyIRC ". (2) Check the "Use external remote controller". (3) Select a button name that you want to use, then click "Learn". (4) Press the button five times (the code value of remote controller is inputted. (5) Click "Apply", then click "OK". Even if you do Learning external remote controller , the buttons of MyHD Remote Controller work normally when you don't select Do not use MyHD remote controller. *Note : Few remote controller can not be recognized the MyHD's remote control receiver. To set up the TV channels and to display the window of "Channel Setting" 1. Select Expanded main control panel/Channel List . 2. Click right mouse button/pop up menu/channel list. 1. Select Ant1(Antenna 1) or Ant2(Antenna 2). 2. Choose Air(terrestrial broadcast) or Cable. * Select Auto if you are not sure of which one to choose. If Auto is selected, the program will automatically detect either Air or Cable. 3. Click on Auto Scan. Scanned channels will appear in the window after searching analog and digital broadcasting channels. A channel is selected from the scanned channels when the channels are up and down. To add channels by manual mode: 1. Input a channel number in the channel box. 2. Choose either analog or digital in the mode box. (If Auto is selected, the program will detect a channel either Air or Cable automatically.) 3. Click on Add , then the channel will be added in the "Scanned Channel" box. To delete channels: 1. Choose a channel that you want to delete from the °Scanned Channel" box. 2. Click on Delete, then the channel is deleted from the "Scanned Channel" box. 1. Check the Show Details to edit a memorized channel name. 2. Highlight a channel that you want to edit, then click Edit button. 3. The below window wil be shown. Type a name that you want to input, and click OK. If you want to display the channel name on the main control panel, go to "Config Panel/VGA Setup/Miscellaneous" to choose "Show Channel Name". ( refer to VGA Settings) . Favorite Channel Mode : This switches to Favorite Channel Mode, Pressing Up/Down button will only change channels in the "favorite channel box ". To add/delete channels to favorite channel box: 1. Choose a channel number in the "Scanned Channel" box. 2. Click on >> button. The channel is added in the favorite channel box. To delete a channel from the favorite channels: 1. Choose a channel number in the "favorite channel box". 2. Click on << button. The channel will be deleted from the "favorite channel" box. To change the sequence of favorite channel list, click up/down in the "favorite channel" box. To set the configure of MyHD program: 1. Click "Config" in the expanded main control or 2. Click right mouse button/pop-up menu/Config Panel then, Config Panel window will be displayed. Multi-mode on an Antenna : One Antenna input may receive both cable channel and air channel. In this case, after option checking, press auto search to investigate all air and cable channel. - Virtual Channel mode can be setup and canceled by "Virtual Channel Mode" button in the Channel Box - When using virtual channel mode, virtual channel number is used rather than physical number in digital broadcasting. Furthermore, Select channel's name automatically by channel name in virtual channel information -Channel number is classified in "virtual" and "physical" for both Memory Channel and Preferred channel in Channel List. - In case of analog channel, physical channel number become virtual channel number -Both kinds of channel can be set only for digital channels. - Virtual channel number and name can be correctly selected only when PSIP information is received. Otherwise, virtual channel number is set as physical channel and channel name is not settled. -In virtual channel mode, if each digital broadcast channel has multiple sub-channels, each sub channels will be set as independent channel. When virtual channel information is not being transmitted properly, channel number will be set by adding extra number such as -1, -2, etc. - After scanning every channel by virtual channel mode, if virtual channel mode is aborted, a channel with multiple sub-chennels will eliminate all the sub-channels except for one sub-channel left. When the user selects virtual channel mode again, Auto-scan has to be redone. Making selection relate to File Play. Play File List shows the list of files to be played. Clicking on "Add Item" button or "Delete Item" button allows you to add or delete files in the Play File List . Click on "Delete Files" button If you want to delete files from your hard disk as well as the Play File List. You can change the order of the Play File List by clicking on "Up" and "Down" button. ? Play list is to manage Play File List (*.mpl). This allows to change and to make new files according to the file format. Example for the "Play List". Messages Explain MYHDPLIST1 MyHD's Play List #1- Indicates a listed file to replay. (Header) <# Generated by MyHD, Date: 2002/11/05 Replay date. <#Sample File. '<#' option means comment. D:\TpStream\1102\documentary.tp files in the list D:\TpStream\1102\HDdrama.tp File not in the list, if file doesn't exist. or ESC button to switch back to the previous channel when OSD is not displayed. (In Full Screen Mode, for channel selection ,refer to Channel Selection of Running MyHD in Full Screen Mode) To control volume: 1. Dragging the knob in the main control panel. 2. Using left/right arrow keys in a keyboard. 3. Handling volume button in the remote control handset. 8 types of input is possible for MyHD. 2 antenna including favorite channel is available. Input(Composite, S-Video) can be received from external A/V. Also, Saved Stream File of Digital TV from Computer hard disk and D-VHS VCR that is connected by IEEE1394 can be played. Futhermore, it can play DVD rom of a computer. To change the input Type; 1. Using input button in the remote control handset. 2. Click "In" key in the main control panel. 3. Click right side button of a mouse. (In Full Screen Mode, for changing input type, refer to Input Mode Setting of Running MyHD in Full Screen Mode) From VGA mode 1. Using file open in the main control panel. 2. Clicking the right button of a mouse, and selecting "File" in the pop up menu. 3. Using Drag & Drop method. From HD mode Using the remote control handset to replay the files when HD mode is played. 1. Add files in "Play File List" from "Config Panel"/"Capture File List". 2. Push the FAV button button in the remote control handset. On Full Screen Mode press FAV button of remote contol to display file list for play. Use Channel Up or Channel Down button to choose one and then press OK to actually play the file. If you wish to cancel press ESC button. ( refer to File Play Setting of Running MyHD in Full Screen Mode) FF/REW : When playing a file, use remote control or number keys on keyboard to control Multiple FF/FF. key board number keys 1(REW*1sec) 2(FF*1sec) 3(FF*2sec) 4(REW*2sec) 5(FF*4sec) 6(FF*sec) For example if FF is set as 10 sec, pressing #5 will move the file to 40sec after. MyHD supports capturing Transport Stream and stores the stream into a HDD to display images any time. If audio is not working properly during capturing, DMA mode should be selected in a HDD. For the perfect capture, we recommend the PC system that is Pentium III 800MHz or higher specifications. During capturing, if size of a file exceed its set value(refer to Capture Mode Detail Options), the file creates a new file by adding "_number" to original file name. ( ex, Capture.tp, Capture_01.tp, Capture_02.tp, and so on. The captured files will be continuously played by order of numbers when they are replayed. To storing Transport Stream, Transport Stream Capture must be selected from "Config Panel"/"Capture Setup"/"Capture Mode". Capturing Pressing Capture button of control panel or Rec button of remote control will save a file to directory that is assigned by capture directory. The file name will be saved as assigned by capture detail option. (refer to Capture Settings) When "Add catured file to list" option in File Play Setting is selected, captured file will be automatically added to file list.During capturing, capture time can be set by pressing Capture button of control panel or Rec button of remote control. Each time you press the buttons, the time will be set in order of 10min, 30min, 60min, 90min, 120min, 180min, infinite. Press Stop button to stop the capturing.Also, press Play/Pause button to pause the capturing. Press Play/Pause button to re-capture the file.Do the same for Full Screen Mode While watching digital broadcast in HD mode, transport stream can be saved by pressing Rec button. Transport Stream Capture after setting Capture time To decide a capturing time, select Capture from the below pop-up menu. 1. Type a desired capturing time in the Capture time box. 2. If you type "0", the capturing will be executed as long as possible. 3. To stop the capture, use Stop button. To execute Motion Video capture, select "Config Panel"/"Capture Setup"/"Motion Video Capture". Capturing .Pressing Capture button of control panel or Rec button of remote control will save a file to directory that is assigned by capture directory. The file name will be saved as assigned by capture detail option. (refer to Capture Settings) When Add catured file to list option in File Play Setting is selected, captured file will be automatically added to file list.During capturing, capture time can be set by pressing Capture button of control panel or Rec button of remote control. Each time you press the buttons, the time will be set in order of 10min, 30min, 60min, 90min, 120min, 180min, infinite. Press Stop button to stop the capturing. Do the same for Full Screen Mode. Motion Video Capture after Capture time is selected Execute same method with Transport Stream Capture after Capture time is selected . During Motion Video Capture, the size of file cannot be limited. The captured files can be replayed through Windows Media Player. Still Image Capture is to capture a still image as a Bitmap (.bmp) or JPEG (.jpg) file To execute Still Image Capture, select "Config Panel"/"Capture Setup" then select "Still Image Capture" in Captue Mode. In detailed options, either Field or Frame Mode can be selected. Saving the still captue image after previewing When you press Capture from popup menu, captured image will display as small image like below. Press Capture button of control panel or Rec button of remote control to keep on adding still image to capture list To view a large image, double click on the small image. ? Click Save button, then the below window will be displayed. ? If you want to save image in JPEG file, please change the format from "Save as type" box. Saving the still captue image directly Pressing Capture button of control panel or Rec button of remote control will save a file to directory that is assigned by capture directory. Press (Shift+S) to capture still Image For Installation of Tape device drvier refer to Tape record and playback Settings For recording 1. Excute MyHD program,then click right button of the mouse. 2. Select "Config Panel>>Capture Setup>>Capture Mode>>Tape". 3. Click on "apply" and "OK". Then choose either a or b method during broadcasting. a. Click "recording button" on the remote controller or main panel. b. Click right button of the mouse, then select "menu>>Capture(Ctrl+C)". Popup window will appear, Click "Recording" after searching a right position of recording tape by the "Rew/FF" button. For replaying 1. Select "menu>>Tape(Ctrl+D)," then "Tape" will be displayed in the main control panel. 2. Use Play/FF/REW buttons for playback. -When video output does not work because programs or settings are changed during playing, click "stop" then "play" button. -If record/playback excutes on MyHD program, the power of VCR will be "ON" even though it is "OFF". -"Time Record" is available even though the power of VCR is "OFF". To be able to use TitanTV Epg, make sure to slect Using TItan TV Epg from Config Panel of VGA Setup MyHD is supporting the functions of watching TV and adding schedule through TitanTV program. The following window is displayed when you press the GUIDE on the Remote Controller or click the Program Guide on Configuration of main control panel while the MyHD is running. When you click button on the window, MyHD will be executed. If MyHD is already executing, a channel is changed to a selected channel. The following window is displayed when you click button on the TitanTV's window. Set "Add Schedule Recording" that you want to record , then click "OK." The setting will be automatically added in "Config Panel/Capture Setup/Capture Reservation.” To record a TV program while watching a program, just click "REC" button on the Remote Controller or click " Capture" button on the main control panel after finishing the "Capture Settings". VGA mode when you disable Using TitanTV Epg from Config Panel of VGA Setup, press the GUIDE on the Remote Controller or click the Program Guide on Configuration of main control panel to show Program Guide like below. In this case, program guide of digital channel that transport PSIP can be viewed, and it can simply add wanted program to reservation capture list. Add to Reservation List : Add to Reservation dialog appears. Choose a brocast program to capture and select Add to Reservation List button. Old broadcast program can not be add to reservation capture list. - Show Reservation List :Show the reservation list. - Press Update button to update program guide. Full Screen mode - Refer to Program Guide of Running MyHD in Full Screen Mode. MyHD supports DVD play function. To play a DVD : 1. Insert a DVD title in your DVD drive. 2. Click the play button on the main control panel. Or 1. Drag a VOB or IFO file from file open window into the MyHD’s overlay window. To set Audio and Subtitle : 1. Use the “Pop -up menu/Audio/Subtitle” Or 1. Use the remote control handset “AUDIO ”button for the Audio and "CAPTION" button for the Subtitle. ? You can eject the DVD title from the drive using by the "eject" button on the main control panel. If audio is DTS format, only SDPIF output work. Note : The functions of Menu, Title and Chapter play are not supported by MyHD, and if the DVD title has copy protection, the HD (Full Screen) Mode is not supported. MyHD supports output of graphic card and HD output in a monitor (refer to monitor configuration ) To view the HD mode; 1. Select HD mode from the pop-up menu, or 2. Click HD button in the main control panel, or 3. Double click the left button of a mouse on the overlay window To exit the HD mode; 1. Double click the left button of a mouse, or 2. Hit Esc key in a keyboard To use the remote control handset; HD mode and an overlay window mode can be activated by HD button on the remote control handset. MyHD.exe /f : execute file mode MyHD.exe /t :execute tape mode MyHD.exe /v : execute Composite mode MyHD.exe /s : execute S-Video mode MyHD.exe file name (TP file or VOB file) : Files will be played after MyHD start to run. MyHD.exe /d : execute DVD mode MyHD.exe /h : execute HD (Full screen) mode * It is working on Windows XP only. For settings of VCR driver 1. Found New Hardware Wizard boxes will be displayed when a D-VHS is connected to your XP machine via firewire. 2. Install software for "AV/C Tape Recorder>>Player". Do not install software for "AV/C Tuners". 3. Choose "Install from a list or specific location(Advaced)". 4. Click on "Next >". 5. Choose "Don't search, I will choose the driver to install". 6. Click on "Next >". 7. Select "Sound, video and game controllers" option and click on "Next >". 8. If you have a JVC Victor HM-DH30000, select "JVC" as the manufacturer and "JVC Tape Device" as the model and click on "Next >". 9. Click on "Finish". 10. JVC D-VHS tape deck is ready to be used by DirectShow applications. For recording 1. Excute MyHD program,then click right button of a mouse. 2. Select "Config Panel>>Capture Setup>>Capture Mode>>Tape ". 3. Click on "apply" and "OK". Then choose either a or b method during broadcasting. a. Click "recording" button on the remote controller or main panel. b. Click right button of a mouse, then select "menu>>Capture(Ctrl+C)". Popup window will be appeared, Use "Rew/FF" to search a right position from tape, then press "Recording" to start tape recording. For replaying 1. Select "menu>>Tape(Ctrl+D)," then "Tape" will be displayed in the main control panel. 2. Use Play/FF/REW buttons for playback. - Try clicking "stop" / "play" button, if problem occurs while playing a video. - MyHD has control over power of Tape Device that has connection to MyHD. - "Time Record" is available even though the power of VCR is "OFF". Hot Key List for MyHD program Information Hot Key File Open Display a file open window Ctrl + O Exit Exit from MyHD Program Ctrl + X Play and stop video Play and Stop The selected file will be played if a file list is shown in HD mode. (To view the Space file list, press “NEXT ” button on the remote control handset) Previous File Play the previous file in the file list Ctrl + ← Next File Play the next file in the file list Ctrl + → Previous File Next File (same as “PREV ” button on Remote Control Handset) Open and select the file list in HD mode (same as “NEXT” button on Remote Control Handset) Open and select the file list in HD mode Ctrl + Shift + ← Ctrl + Shift + → Fast Forward Forward the playing file by a selected skip time (refer to ‘File Play Setup’) Shift + → Rewind Backward the playing file by a selected skip time Shift + ← Number Keys (0~9) Change a channel using by numbers 0~9 Change channels in memorized channels Move Channels If “Favorite Channel Mode” is selected, changing channels in favorite ↑,↓ channels Information Show information of current state Ctrl + Enter Return Exit from the file list in HD mode Shift + ESC Mute Press to temporarily cut off the sound Ctrl + U CAPTION Display available captions (It will be supported in next version) Ctrl + T GUIDE Audio Display the on-screen Electronic Program Guide (EPG). (It will be supported in next version) Select an analog audio among Stereo, Mono, and Bilingual. If several digital audio signals exist, one of audio will be selected in the order. Ctrl + G Ctrl + A MENU Display menu on HD mode(It will be supported in next version). Ctrl + E Aspect Ratio Select an aspect ratio among Letter Box, Full and Zoom Ctrl + R HD mode (Full Screen) Select the HD or Overlay window mode Ctrl + H Stop Stop the play Ctrl + Space Record (same as the “REC” button on the remote control handset) Record the current broadcast according as “Capture Mode.” Shift + C Capture Display “Capture window” to input file name and capture time. Ctrl + C Channel Setting Display “Channel Setting ” window to set up channels. Ctrl + L Input Mode Select the input of Antenna1, Antenna2, Composite, S- Video, DVD or Tape (only for Windows XP) in the order Ctrl + I Antenna1 Select antenna1 as input Ctrl + 1 Antenna2 Select antenna2 as input Ctrl + 2 Composite Select Composite as input Ctrl + v S-Video Select S-Video as input Shift+ v File Select an input to play files Ctrl + f DVD Select an input to play DVD Shift + d Tape Select an input to interface with a D-VHS device Ctrl + d Favorite Channel Select or cancel the current channel as a favorite channel Shfit + M Sub-channel Select sub-channels in the order if there are sub -channel on broadcast Ctrl + S Previous Channel Still Image Capture Using Separate Monitor Overlay Window Mode Alternate between the current channels and the last channel that was displayed. Capture Still Image Select or cancel the settings of separate monitor. It is the shortcut for “Config Panel/VGA Setup/Using Separate Monitor.” Display the overlay window on your display device. It is the shortcut for “Config Panel/VGA Setup/Show Overlay Window.” Shift + p Shift + S Ctrl + Shift + M Ctrl + Shift + O Select a resolution by a number. 1. 1920x1080I 2. 1280x720P 3. 720x480P 4. 720x480I Video Resolution 5. 1440x1080I 6. 1024x768P Ctrl+Shift+# 7. 1360x768P 8. 1280x1024P 9. 800x600P 10. 864x480P It is the shortcut for “Config Panel/AV Setup/Video Resolution.” Next Resolution Select a next resolution in the order. It is shortcut for “Config Panel/AV Setup/Video Resolution.” Ctrl+N
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 67 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:65b6022c-569a-49e3-98f7-8b275f64838d Producer : Acrobat PDFWriter 4.0 Windows NT¿ë Modify Date : 2005:01:13 14:16:41+09:00 Create Date : 2003:04:29 18:53:19Z Creator Tool : MDP100 - Microsoft Internet Explorer Metadata Date : 2005:01:13 14:16:41+09:00 Document ID : uuid:c45272d5-b135-4c4d-9c57-96fcb0f81f51 Format : application/pdf Title : file://D:\user\sunny\project\pc_dtv\document\FCC%20Certificatio Creator : Owner Author : OwnerEXIF Metadata provided by EXIF.tools