Macro Image Technology MDP-130 HDTV Receiving PC Card User Manual print job
Macro Image Technology, Inc HDTV Receiving PC Card print job
Contents
- 1. Users Manual DTV
- 2. Users Manual DVI
Users Manual DVI
DVI—D Adaptor for MyHD MDP-130 MyHD DVI Card Enjoy M yHD on Digital Monitors ’ f MDP—ISODVI ' ) % Macro Image Technology y II DVI Card l Package List Thll package [8 Including : - MyHDMDP-130DVI adaptor - PCB spacer - Installation guide - DVI-D Ioop-Qhrough cable My ll DVl Card l Installation of MDP-1300VI adaptor WARNING - Static Sensitive Components To avoid possible demege toMDP-130DVI adaptor and/or other system components from seed: dimarge, always discharge your body's static electnoity prior to handling MDP- 13oDVI adaptor or other system components. Discharging can be done either by using a properly grounded anti—static wrist strap or by simply touching the chassis of e grounded(plugged—in) computer. In addition, always handle we adaptor with care by holding its edges end not touching its metal connectors whenever possible, to avoid mechanical and electrical damage to delicate components on the adaptor. To install theMDP-1300VI adaptor. follow the slaps listed below: 1. With the power off, remove your computer cover and detach the installed Mop-130 t A ‘i card or take the brand new MDP-130 card out of the relail box. (Before handling the _ x card or adaptor, ground yourself by ' touching the power supply box inside your computer.) . Remove the screw attached to the corner of the MOP-130 card and screw the spacer on the screw hole where the removed screw was installed. y II DVI Card 3. Position the digital interface connector (male headers) of the MDP-1SODVI adapter to the digital interlace connector (female connectors) of the MDP-130wrdt (WARNING : Be sure to match the connector pins on the conect position. Mie—rnamhing oi pin positions will give the permanent damage to the adaptor and/or to other system components when you turn on the computer.) 4. Make sure that the pins of the digital interface connectors are connected correctly and make sure that the screw hole of the spacer on the MDP-130cerd and the hole of the MDP-130DVI adaptor are matched correctly And then install the screw which has been removed from the MDP-130 card on the screw hole of the spacer. 5. The MDP-130 card with theMDP-1soDVl adaptor needs two PCI slots, so remove thaslotcuverotthe PCI slot nexttotha slot at which the MDP-13o card was placed. . Position the MDP-130 card directly above the PCI slot and Insert the card firmly into the slot. Special care should be taken to press It evenly and snugly Into Its slot. .Inata|ledtheacrewsontheslotcoveraot the MDP-130 card and MDP-130DVI adapter. My ID DVI Card I Connecting the DVI monitor to MyHD 1. Connect the one conneflor oi the DVI-D cable to the DVI input connector oi the monitor. 2. Connect the other connector of the cable to the DVI output connector (next to the optical SPDIF connector) of the MyHD MOP-130W! adaptor. (WARNING: Be sure to connect the cable to the DVI output connector of the adaptor. do not connect the monitor cabia to the DVI input connector of the adaptor.) y II DVI Card I Loop through the DVI video of the graphic card 1. You can view the DVi video of VGA on the monitor which is connected to the MDP- 1300Vl adaptor it you have the graphic card which has DVI output. .Canect the one connector of the DVI-D hop-through cable to the DVI output connector of the graphic wcd‘ . Connect the other connector of the cable to the DVI input conneaor (opposite side to the optical SPDIF connector) of the MyHDMDP-13ODVI adaptor. (WARNING : Be sure to connect the cable to the DVI input connector of the adaptor, Do not connect the loop- through cable to the DVI output connector of the adaptor or the permanent damage may be caused on the adaptor and/or the graphic card.) .VoucanswimhthevideobetweenthegraphtcwrdandtheMyHDusingtt'leMyHD software. (Refer to the user guide of MyHD) My ID DVl Card I Connecting SPDIF output to the external receiver 1, Connect one connector of the optical cable to the optical SPDIF input connector of the extemel receiver. 2. Connect the other connector of the cable to the SPDIF output connector of the MD MDP-1SODVI adaptor‘ ; m mnmao FCC Information This deVice complies with Part 15 of the FCC Results. Operation is subject to the followmg two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply With the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to proVide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This eqUipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference Will not occur in a particular installation. If this equipment does cause harmful interference to radio or telewsion reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1, Reorient or relocate the receivmg antenna. 1.2. Increase the sepamtion between the equipment and receiver. 13. Connect the equipment into an outlet on a circuit different from that to which receiver is connected 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could VOId the user's authority to operate the equipment. Q Macro Image Technology For product service. product information or assistance. Please refer to our website. Send an e-mail, or call us 6th Floor, East Bldg. I'I'Venture Tower. 78 Gerekbon-Dong, Songpe-Gu, Seoul, Korea, 1384803 TEL : +82-2~2142~4000 FAX : +82-2-2142-4099 Website : www.DTVso|ufion.oom e—mail : sales@mitinc.oo.kr
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 9 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:28bfdca0-68c9-4ece-99a9-8a280292265e Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2005:02:01 20:23:02+09:00 Create Date : 2005:02:01 20:11:33+09:00 Metadata Date : 2005:02:01 20:23:02+09:00 Document ID : uuid:107067fd-3b03-40b5-be30-4ca37dd9ea19 Format : application/pdf Title : print job Creator : schong Author : schongEXIF Metadata provided by EXIF.tools