Mandolyn Electronic Technology RT601 Light Sensor User Manual RT100RT601 Manual

Mandolyn Electronic Technology Inc. Light Sensor RT100RT601 Manual

Users Manual

GETTING STARTED battery installationCOUNTDOWN TIMER RANDOM FUNCTION TROUBLESHOOTING12remove the battery cover from the back of the timerplace two button cell batteries between terminals observing proper polarity then replace coverPROGRAMON/OFF CDSETRANDOMRESET357 92 4 6 8101PROGRAMON/OFF CDSETRANDOMRESET321short/long randomprogrammable randomPROGRAMON/OFF CDSETRANDOMRESET2143LCD display seems “frozen”. Buttons won’t respond.Timer loses programs when unpluggedProgrammed ON/OFF times don’t executeProgrammed ON/OFF times don’t execute at specified times.Transmitter stops turning receiver on and off.Press reset button to reset timer.Replace batteries.Ensure that the program disable feature is not enabled.Ensure that the random function is not enabled.Use the LEARN function to reprogram the receiver or check the batteries.problem solutionTECHNICAL SPECIFICATIONSProgrammable Timer RCT100Ratings: 120V AC, 15AMax Load: 1800W resistive; 600W tungstenPhotocell Transmitter RT601Transmission Range: up to 40m in open areaTransmission Frequency: 433.92 MHz1425678Press SETStart ON or OFF select with Press SETHour select withPress SETMinute select with9103Press SETSecond select withPress SETThe to-the-second countdown feature of this timer starts from the ON or OFF position and counts down to zero when activated.Press once fromLEARNPROGRAMON/OFF CDSETRANDOMRESETStop countdown timer function with CD or ON/OFFremove the battery cover from the transmitterplace two AA size batteries into compartment observing proper polarity then replace cover 12button descriptionsRANDOMRESETPHOTOCELL TRANSMITTER2Repeat and for additional timers (available at your local retailer).Press and hold ON/OFF and together on timer while simultaneously pressing the RF button on the transmitter. (The green LED indicator on the transmitter will flash when RF is pressed).11Plug timer into wall socket2LEARNPROGRAMON/OFF CDSETRANDOMRESET1*1PROGRAM SETTINGSdisable program/master disablePROGRAMON/OFF CDSETRANDOMRESET 13572 4 6 8PROGRAMON/OFF CDSETRANDOMRESET 143Press SETDay select with Press SETHour select withPress SETMinute select withPress SETProgram select with Press SETPress ON/OFF to disable ( X )For single disable select PROGRAM with For master disable go to using2Press SET 3 times to exit (single disable)OR press SET 4 times to exit (master)CLOCKPrograms are arranged in a circular pattern with the clock and countdown functions:CLOCK Program 1-20 CDRepeat steps to to undo disable ( X )14Press CD to start the countdown functionTIMING CONTROL DIALMODE SWITCH BRIGHTNESS DIALNEW CODE BUTTONRF “TRANSMIT” BUTTONLED INDICATORPHOTOCELLThe transmitter uses an intelligent code system to prevent interference from other sources. But if you do experience such interference, you can press the NEW CODE button to generate a new random house code. However, after pressing the NEW CODE button, you will need to redo the LEARNING procedure as described above.The photocell transmitter can control multiple remote programmable timers.PHOTOCELL TRANSMITTER*The LED INDICATOR of the transmitter will:1Once you insert batteries into the transmitter, you will automatically enter the user setting mode. This mode will last for two minutes in which you can easily adjust the brightness or light sensitivity of the photocell sensor.Alternately, you can press the RF button on the transmitter to enter the user setting mode.2In user setting mode, turn the BRIGHTNESS DIAL to adjust the light sensitivity of the photocell sensor.2user setting mode> TURN ON - when the photocell sensor detects that it is brightUse the LED INDICATOR (on front of transmitter) as a reference, so that you can fine tune the light sensitivity as desired.> TURN OFF - when the photocell sensor detects that it is dark*12*1learn functionPHOTOCELL TRANSMITTERTransmits an “ON” command to the timer when photocell senses a change from dark to bright. Transmits an “OFF” command after the time delay as set by the Timing Control Dial or when it turns from bright to dark.3Once the learn function has been successfully executed, the symbol will flash on the top right corner of the LCD on the timer, every time the transmitter sends a signal or when the RF button is pressed.3day mode / night modeThe photocell transmitter works by detecting the brightness level of its surroundings and sends ON or OFF commands to the timer. The transmitter can be set to trigger the timer to run for 30mins, 1, 2, 4, 6, 8, 10hrs or continuously, and will automatically turn the timer OFF when the photocell senses a change from dark to bright (in NIGHT mode) or bright to dark (in DAY mode).Transmits an “ON” command to the timer when photocell senses a change from bright to dark. Transmits an “OFF” command after the time delay as set by the Timing Control Dial or when it turns from dark to bright.DAY MODE:NIGHT MODE:Turn TIMING CONTROL DIAL to select delay off time.(30 minutes, 1, 2, 4, 6, 8, 10 hours, or continuous)Slide MODE SWITCH: up for DAY mode and down for NIGHT mode22This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions:FCC / RSS-210 COMPLIANCE1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation.Flashing for short randomFlashing for long random12Press RANDOM3Short random from OR Long random from CDRNDLRND-* Short random 1-2 hours, long random 2-3 hours12Press RANDOMSet program 20 to desired random time33Select program 20 withSolid for programmable randomRND* Programmable random only works with program 20; 1-2 hours4Deactivate random function with RANDOM or ON/OFFPROGRAMON/OFF CDSETRANDOMRESET112357 92 4 6 810CLOCKGo to usingCLOCKTo activate/deactivate Daylight Saving Time (DST) function, press and hold both and together for 3 seconds in mode; solid for DST.To toggle between 12/24 hour format, press RANDOM during clock setting.123COUNTDOWNSETON/OFFPROGRAMTIMER OPERATIONProgrammable Timer Photocell TransmitterRCT100 + RT601Programmable Timer withWireless Photocell Transmitter142567831234LEARNPROGRAMON/OFF CDSETRANDOMRESETsetting the clockINSTRUCTION TO THE USERThis equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions , may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:PHOTOCELL TRANSMITTER•••••For safety, set the photocell transmitter to trigger the lights ON inside your doorway at dusk.For convenience, set the photocell transmitter to start your coffee maker at first light.For security, set the transmitter to activate lights in your home while you are away (day or night).For energy savings, set the transmitter to trigger your timer for controlled periods of time.To maximize functionality, combine the time settings of the photocell transmitter with those of the programmable timer to achieve your desired ON/OFF applications.20 ON/OFF settingsCountdown timer3 random functions12/24 hour clock15A, 1800W (resistive)433 MHz RF technologyActivates timer at dusk or at dawnTiming Control Dial - (30mins, 1, 2, 4, 6, 8, 10hrs, or continuous operation)Brightness Dial - for light sensitivity adjustmentTransmission range: up to 40m in open area1425678Press SETDay select with Press SETHour select with9103Press SETSecond select withPress SETPress SETMinute select withOWNERS MANUALCongratulations on your purchase of a UPM remote control product. Please take the time to read and understand this manual so you can begin to enjoy the convenience and energy saving benefits this product has to offer.PROGRAMMABLE TIMERPHOTOCELL TRANSMITTERapplicationsReorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.

Navigation menu