Master Lock 3681 3681 User Manual Exhibit D Users Manual per 2 1033 b3
Master Lock Company 3681 Exhibit D Users Manual per 2 1033 b3
Exhibit D Users Manual per 2 1033 b3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3391398 |
| Application ID | xjbumn4JlBgPg/vl/35+BQ== |
| Document Description | Exhibit D Users Manual per 2 1033 b3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 37.83kB (472914 bits) |
| Date Submitted | 2017-05-15 00:00:00 |
| Date Available | 2017-05-15 00:00:00 |
| Creation Date | 2017-02-20 10:44:33 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-02-20 11:12:58 |
| Document Title | Exhibit D Users Manual per 2 1033 b3 |
| Document Creator | Adobe InDesign CC 2017 (Macintosh) |
Electronic Built-In Lock • Spanish Electronic Built-In Lock • French Electronic Built-In Lock Installation Instructions • Instructions d’installation Instrucciones de instalación 3681 • 3685 1. Open box • To prevent damage to the lock, DO NOT USE a sharp object to open packaging • Keypad module and lock module will be in same package 2. Remove keypad module and lock module from package 3. Open locker door 4. With one hand, align front housing through 2 mounting holes on the front of the locker door. (A) • Pull the connection ribbon through the large middle mounting hole • Note: The diameter of the mounting holes must be 7/32in minimum for proper installation and fit. If the holes are undersized, a 7/32in drill bit can be used to widen them. 5. With your other hand, line up the lock module on the back of the door and attach the connection ribbon (B) 6. Feed excess ribbon cable back into center mounting hole (C) 7. Line up the threaded screws from the keypad module with the holes in the lock module (D) 8. Install nuts on the threaded screw and tighten with 3/8in nut driver (E) • Note: Tighten fastener to a maximum torque of 3N-m (20-25in-lbs) to avoid product damage or lock failure 9. Close locker door 10. Test lock for functionality (Refer to Multi-User and Single-User Instructions) (A) Notes: 1. Battery included 2. Lock is configured to work on 1/32in, 1/2in, and 3/4in door depths 3. Lock is configured to work on left and right hinged doors 1. Open box • To prevent damage to the lock, DO NOT USE a sharp object to open packaging • Keypad module and lock module will be in same package 2. Remove keypad module and lock module from package 3. Open locker door 4. With one hand, align front housing through 2 mounting holes on the front of the locker door. (A) • Pull the connection ribbon through the large middle mounting hole • Note: the diameter of the mounting holes must be 7/32in minimum for proper installation and fit. If the holes are undersized, a 7/32in drill bit can be used to widen them. 5. With your other hand, line up the lock module on the back of the door and attach the connection ribbon (B) 6. Feed excess ribbon cable back into center mounting hole (C) 7. Line up the threaded screws from the keypad module with the holes in the lock module (D) 8. Install nuts on the threaded screw and tighten with 3/8in nut driver (E) • Note: tighten fastener to a maximum torque of 3N-m (20-25in-lbs) to avoid product damage or lock failure 9. Close locker door 10. Test lock for functionality (Refer to Multi-User and Single-User Instructions) (B) (C) Notes: 1. Battery included 2. Lock is configured to work on 1/32in, 1/2in, and 3/4in door depths 3. Lock is configured to work on left and right hinged doors continued on other side / continué a l’autre côté / continuado al otro lado 1. Open box • To prevent damage to the lock, DO NOT USE a sharp object to open packaging • Keypad module and lock module will be in same package 2. Remove keypad module and lock module from package 3. Open locker door 4. With one hand, align front housing through 2 mounting holes on the front of the locker door. (A) • Pull the connection ribbon through the large middle mounting hole • Note: The diameter of the mounting holes must be 7/32in minimum for proper installation and fit. If the holes are undersized, a 7/32in drill bit can be used to widen them. 5. With your other hand, line up the lock module on the back of the door and attach the connection ribbon (B) 6. Feed excess ribbon cable back into center mounting hole (C) 7. Line up the threaded screws from the keypad module with the holes in the lock module (D) 8. Install nuts on the threaded screw and tighten with 3/8in nut driver (E) • Note: Tighten fastener to a maximum torque of 3N-m (20-25in-lbs) to avoid product damage or lock failure 9. Close locker door 10. Test lock for functionality (Refer to Multi-User and Single-User Instructions) (D) Notes: 1. Battery included 2. Lock is configured to work on 1/32in, 1/2in, and 3/4in door depths 3. Lock is configured to work on left and right hinged doors (E) Display Screen Key Display Screen Key Display Screen Key 1. Low Battery 2. Settings Mode 3. Locked 4. Unlocked 5. Single-User Mode 6. Bluetooth Mode ADA Model Only (FOB Required) 7. Invalid Code 8. Bolt Jam 9. Entered Code 10. Awaiting Code 1. Low Battery 2. Settings Mode 3. Locked 4. Unlocked 5. Single-User Mode 6. Bluetooth Mode ADA Model Only (FOB Required) 7. Invalid Code 8. Bolt Jam 9. Entered Code 10. Awaiting Code 1. Low Battery 2. Settings Mode 3. Locked 4. Unlocked 5. Single-User Mode 6. Bluetooth Mode ADA Model Only (FOB Required) 7. Invalid Code 8. Bolt Jam 9. Entered Code 10. Awaiting Code 10 The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and used under license by Master Lock Company LLC. ® Le mot servant de marque Bluetooth et les logos sont des marques enregistrétés de Bluetooth SIG, Inc. et, utilisés sous license par Master Lock Company LLC. ® La palabra marca Bluetooth y los logos son marcas registradas de propiedad de Bluetooth SIG, Inc. y utilizadas bajo licencia por Master Lock Company LLC. ® Notice: This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device. Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Notice: This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device. Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Notice: This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device. Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. w w w.masterlock. c o m © 2017 Master Lock Company | All Rights Reserved Master Lock Company LLC, Milwaukee, WI 53210 U.S.A. | 800-308-9244 Master Lock Canada, Oakville, Ontario L6H 5S7 Canada | 800-227-9599 P52953
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Create Date : 2017:02:20 10:44:33-06:00 Metadata Date : 2017:02:20 11:12:58-06:00 Modify Date : 2017:02:20 11:12:58-06:00 Creator Tool : Adobe InDesign CC 2017 (Macintosh) Instance ID : uuid:f17eab57-de3e-40de-aa8d-fe9ef9ad13cc Original Document ID : xmp.did:CE19C9B5902068118BA38F5F5C399DE1 Document ID : xmp.id:d679d749-c6d8-4bfa-8785-9a4531e084f2 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:269fd019-f801-4f6c-a57c-22c56c6b2586 Derived From Document ID : xmp.did:2ad68a7c-7510-45de-b11d-fa12158cdc6b Derived From Original Document ID: xmp.did:CE19C9B5902068118BA38F5F5C399DE1 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Macintosh) History Changed : / History When : 2017:02:20 10:44:33-06:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CC 2017 (Macintosh)EXIF Metadata provided by EXIF.tools