Maxon Electronics Australia MM-5500PRO Wireless CDMA 1XEVDO Ethernet Modem User Manual MM 5100 Control Box
Maxon Electronics Australia Pty. Ltd. Wireless CDMA 1XEVDO Ethernet Modem MM 5100 Control Box
Users Manual
MM-5500PRO Quick Start Manual Wireless CDMA 1x EVDO Ethernet modem Technical Support: engineering@maxon.com.au TEL : 61 2 9707 2000 FAX : 61 2 9707 3328 www.maxon.com.au 2 FCC RF EXPOSURE COMPLIANCE In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. This MM-5500PRO Wireless Ethernet modem has been tested for FCC exposure compliance with the MM-5500PRO wireless ethernet modem form factor. In order to comply with FCC RF exposure requirements, the MM-5500PRO Wireless Ethernet modem must be operated with the MM-5500PRO wireless ethernet modem form factor. The use of this device in any other type of host configuration may not comply with FCC RF exposure requirements and should be avoided. During operation, a 20cm separation distance should be maintained between the antenna, whether extended or retracted, and the user’s/bystander’s body (excluding hands, wrists, feet, and ankles) to ensure FCC RF exposure compliance. CAUTION Change or modification without the express consent of Maxon Electronics Australia Pty. Ltd. voids the user’s authority to use the equipment. This equipment has been tested and found to comply with the limits pursuant to Part 22 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in an appropriate installation. This equipment generates, uses, and can radiate radio frequency energy and, if not used in accordance with instructions, can cause harmful radiation to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference in radio and television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna 3 Table of Contents Copyright………………………………………………………………………………………………………………….4 Purpose…………………………………………………………….………………………………………………………4 1. Introduction.………………………………………………….…………………………………………………………5 1.1 MM-5500PRO Overview………………………………………………………………………………….5 1.2 Features……………………….………………………………………………………………………………….5 2. Operation Process……………………………………………………………………………………………………6 2.1 PPP mode……………………………………………………………………………………………………….6 2.2 PPPoE mode…………………………………………………………………………………………………….6 3. Factory Default…………………………………………………………………………………………………………7 3.1 Connecting Internet…….………………………………………………………………………………….7 4. MM-5500PRO Configuration………….………………………………………………………………………..9 5. PPP mode Configuration…………………………………………………………………………………………11 6. PPPoE mode Configuration…………………………………………………………………………………12 7. Firmware Upgrade…………………………………………………………………………………………………21 8. Radius Test………….…………………………………………………………………………………………………22 9. Appendix…………………………………………………………………………………………………………………24 4 Copyright Advance product information describes products which are in development and subject to development changes. INEWDC has made best effort to ensure that the information contained in this document is accurate and reliable. This document is the property of INEWDC and implies no license under patents, copyrights, trade secrets. No part of this publication may be copied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic, mechanical, photographic, or otherwise) without the prior permission of INEWDC. Purpose This manual includes how to configure and use the MM-5500PRO. 5 1. Introduction 1.1 MM-5500PRO Overview There are a lot of connections for Internet. Figure 1 shows one of the connectivity on the internet using a normal ADSL modem. [Figure 1. Normal Network using an ADSL Modem] MM-5500PRO is an wireless ethernet modem that supports the connection between LAN (Local Area Network) to WAN(Wide Area Network) wirelessly in Small Office Home Office. Figure 2 shows the MM-5500PRO’s shape. [Figure 2. Each part name of MM-5500PRO] MM-5500PRO supports WAN protocol like PPP, HDLC etc. using CDMA 1x EVDO modem, routing and bridging functions internally for the high speed data transfer. 1.2 Features 6 2. Operation Process There are two-way of MM-5500PRO operation. One is PPP (Point to Point Protocol) mode and the other one is PPPoE(PPP over Ethernet) mode. 2.1 PPP mode On PPP mode MM-5500PRO has the IP from ISP (Internet Service Provider) itself, so MM5500PRO can share the IP with many Host PCs. Below figure 3 shows PPP mode operation. [Figure 3. PPP mode operation] First, Host PCs get each private IP(hereby IP-1) from MM-5500PRO via DHCP server. Second MM-5500PRO gets public/Private IP(hereby IP-2) from ISP via CDMA 1x EVDO modem. Now MM-5500PRO has two kinds of IP, one is from ISP and the other ones are to Host PCs. Third, MM-5500PRO convert network data between IP-1 and IP-2 via NAT. 2.2 PPPoE mode On PPPoE mode MM-5500PRO has no IP, just the Host PC gets IP from ISP. [Figure 4. PPPoE mode operation] Different on PPP mode, the IP from ISP goes to Host PC directly. MM-5500PRO converts protocol from PPP to PPPoE or on reverse direction, the Host PC processes all network protocols. 7 3. Factory Default MM-5500PRO is already set for normal operation. So just connect between PC and MM5500PRO. Check the network environment of Host PC. 3.1 Connecting Internet For accessing Internet, should obtain IP automatically so refer below steps. (1) Assumed the user uses the Windows XP. For connect between PC and MM-5100PRO, click “My Network Places” choose the [properties]. [Figure 5. First step of setting the Host PC] (2) Check the “Local Area Connection”, click the mouse right button then [Properties]. [Figure 6. Second step of setting the Host PC] (3) Chose “Internet Protocol [TCP/IP]” Tab and double click the item. 8 [Figure 7. Third step of setting the Host PC] (4) Check the “Obtain an IP address automatically” then click the [OK] button. [Figure 8. Forth step of setting the Host PC] (5) Host PC’s setting is finished. Connect Power and Ethernet cable on MM-5500PRO. Wait for about 10 seconds or until the LED of PKT blinks. Connect your PC on Internet. 9 4. MM-5500PRO Configuration User can change the function of MM-5500PRO by configuring it for user’s purpose. Supports the web based configuration pages for simplified installation and setup. Figure 9 shows connection on MM-5500PRO’s configuration. [Figure 9. Configuration of MM-5500PRO] (1) Connect Power cable on MM-5500PRO. (2) Connect LAN cable between Host PC and MM-5500PRO. (3) Set Host PC network environment below. - Host PC IP : 192.168.0.2(except 1: 1 is MM-5500PRO) - Subnet mask : 255.255.255.0 - DNS : (omit) Figure 10 shows the window of Internet Protocol(TCP/IP) Properties. (if don’t know how to find below window, go to page 5) [Figure 10. Setting Host PC] (4) Start web browser like Internet explore then write IP address, 192.168.0.1 (by default) for connecting web page of configuration in MM-5500PRO. 10 (5) The pop-up window of login page appears like figure 11. - User name: admin - Password: admin (6) “Home” page shows the system information of MM-5500PRO. [Figure 11. Home Page] ITEM System Name Up Time Description Product Name Operation time from power on eth0 : Status of Ethernet0 IP Interface ppp0 : Status of CDMA0 IP (After getting IP from ISP, this IP appears) (7) We saw the connecting web page of configuration in MM-5500PRO, now try to set each configurations for each mode. 11 5. PPP mode Configuration We assume that MM-5500PRO current mode is not PPP mode in this chapter. (1) Connect Power cable on MM-5500PRO. (2) Follow the chapter 4, connect MM-5500PRO’s configuration web page. (3) Click “PPP/PPPOE” menu then PPP/PPPOE page appears like figure 12. [Figure 12. PPP/PPPOE Page] ITEM Select Mode User ID User Password Tel Number Description PPP user@telstra.internet (or others) Password #777 1 : 1x, EVDO (By default) CRM 150 : 1x only 160 : EVDO only (4) All setting finished then Click the button. (5) Disconnect power cable then reconnect it. (6) Follow the chapter 3, change the Host PC’s network environment. (7) Execute web browser and explore internet. 12 6. PPPoE mode Configuration We assume that MM-5500PRO current mode is not PPPoE mode in this chapter. (1) Connect Power cable on MM-5500PRO. (2) Follow the chapter 4, connect MM-5500PRO’s configuration web page. (3) Click “PPP/PPPOE” menu then PPP/PPPOE page appears like figure 13. [Figure 13. PPP/PPPOE Page] ITEM Select Mode Description PPPoE User ID Not effect User Password Not effect Tel Number Not effect 1 : 1x, EVDO (By default) CRM 150 : 1x only 160 : EVDO only (4) All setting finished then Click the button. (5) Disconnect power cable then reconnect it. (6) Follow the chapter 3, change the Host PC’s network environment. 13 (7) In this example we assumed the user uses the Windows XP. If it is not Windows XP, the user should install PPPoE connection application program. For connect between PC and MM-5500PRO click the “My Network Places” choose the [properties]. [Figure 14. First step of setting the Host PC] (8) Check the “Local Area Connection”, click the mouse right button then [Properties]. 14 [Figure 15. Second step of setting the Host PC] (9) Chose Internet Protocol[TCP/IP] Tab and double click the item. [Figure 16. Third step of setting the Host PC] (10) Check the “Obtain an IP address automatically” then click the [OK] button. 15 [Figure 17. Forth step of setting the Host PC] (11) You should make PPPoE connection so click the “Create a nee connection” [Figure 18. First step of creating a PPPoE connection] (12) New Connection Wizard appears, click [Next] button. 16 [Figure 19. Second step of creating a PPPoE connection] (13) Check “Connect to the Internet” then click [Next] button. [Figure 20. Third step of creating a PPPoE connection] (14) Check “Set up my connection manually” then click [Next] button. 17 [Figure 21. Forth step of creating a PPPoE connection] (15) Check “Connect using a broadband connection that requires a user name and password” then click [Next] button. [Figure 22. Fifth step of creating a PPPoE connection] 18 (16) Write the ISP Name what you want. In this example write ISP name then click [Next] button. [Figure 23. Sixth step of creating a PPPoE connection] (17) Write User name/Password/Confirm password what you use. Then click [Next] button. [Figure 24. Sixth step of creating a PPPoE connection] 19 (18) All setting is finished, check “Add a shortcut to connection and close this wizard, click Finish” then click [Finish] button. [Figure 25. Seventh step of creating a PPPoE connection] (19) PPPoE connection program appears then click [Connect] button. [Figure 26. PPPoE connection application program] 20 (20) Connecting window appears, trying to connect MM-5500PRO. [Figure 27. Connecting between PC and MM-5500PRO] (21) After connection between PC and MM-5500PRO, then go to the verifying stage. [Figure 28. Verifying username and password] (22) Changing Registering stage, the Host PC connecting on the network. [Figure 29. Registering PC on the network] (23) Click the [Start] button then choose Internet Explorer. 21 [Figure 30. Starting Internet Explorer] 7. Firmware Upgrade Firmware is for MM-5500PRO. When the firmware is to be upgrade or to be download, use like this. (1) Connect Power cable on MM-5500PRO. (2) Follow the chapter 4, connect MM-5500PRO’s configuration web page. (3) Click “Upgrade” menu then PPP/PPPOE page appears. (4) Click the button and search the firmware file. (5) Select the firmware file then “OK”. 22 [Figure 31. Firmware Upgrade] (6) Click the button then below Figure 31 appears. [Figure 32. Firmware Upgrade finished] (7) Execute web browser and explore internet. 8. Radius Test There is no needed RADIUS on normal using wireless AP but if connect user PC using RADIUS protocol, there are some needed to define below. (1) Wireless AP supports RADIUS protocol to communicate with MM-5500PRO. (2) ISP(Internet Service Provider) supports subnet mask 255.255.255.xxx (because Client PCs should get their IP from RADIUS Server). (3) RADIUS Client Software is installed on Client PC. 23 (4) Get the RADIUS Server information including Authentication Server IP/Port and Accounting Server IP/Port. (5) IP of MM-5500PRO should be registered in advance.(But now MM-5500PRO gets Dynamic IP from ISP so after get the IP from MM-5500PRO then let the RADIUS server know the MM-5500PRO’s IP. In the future if MM-5500PRO using RADIUS protocol, MM5500PRO needed Static IP from ISP). [Figure 33. RADIUS Authentication and Accounting Network] (6) Connect Power cable on MM-5500PRO. (7) Follow the chapter 4, connect MM-5500PRO’s configuration web page. (8) Click “RADIUS” menu then RADIUS page appears. 24 [Figure 34. RADIUS Setting Page] ITEM Description Server IP : xxx.xxx.x.x Authentication Server Server Port : xxxx Shared Secret : depend on Authentication Server Server IP : xxx.xxx.x.x Accounting Server Server Port : xxxx Shared Secret : depend on Authentication Server Server Timeout Max.Request Second of time out (depend on network speed) Time of Request (normal 2~3 times) Session Timeout Default by server Idle Timeout Default by server Interim Interval Default by server (9) All setting finished, execute the RADIUS Client Software that is installed on Client PC then connect on Internet. 25 9. Appendix Below pages are descriptions of other configuration pages. (1) “Status” page shows current protocol status. [Figure 35. Status Page] ITEM Description Information of Target - Device - ARP Select Statistics - IP - ICMP - TCP - UDP - ROUTE 26 Device Statistics Each status & Information (2) “Ethernet” page shows the information of Ethernet interface. [Figure 36. Ethernet Page] ITEM Connect Type IP Address Subnet Mask Gateway DHCP Hostname Description Static: Should be Always (Dynamic: Will be omit) eth0 IP Subnet mask IP Address Gateway Address (Will be omit) 27 (3) “PPP” page shows the information of PPP authentication. [Figure 37. PPP Page] ITEM User ID User Password Tel Number Description Received ID from ISP Password Calling number (4) “DNS” page shows the information of setting DNS IP Address. [Figure 38. DNS Page] 28 ITEM Description 1st DNS IP Address First DSN IP (Optional) 2nd DNS IP Address Second DSN IP (Optional) (5) “DHCP” page shows the information of setting DHCP. [Figure 39. DHCP Page] ITEM Activate Description Enable/Disable: DHCP server on-off Start IP Address Start address local IP(start range) End IP Address End address local IP(End range) Subnet Mask Default Lease Time Subnet mask IP Address Default Time of assigning IP Max Lease Time Maximum Time of assigning IP Default Gateway Gateway IP Address 29 (6) “NAT” page shows the information of setting NAT. [Figure 40. NAT Page] ITEM Operation Virtual Sever Access Control DMZ Host IP VPN Pass-Through IP Description Enable/Disable: NAT on-off User can select/configure NAT option End address local IP(End range) Setting DMZ Host IP Address VPN IP Address 30 (7) “RADIUS” page shows the information of setting RADIUS. [Figure 41. RADIUS Page] ITEM Server IP Shared Secret Server IP Shared Secret Description Authentication Server IP & Port RADIUS Secret Key Accounting Server IP & Port Accounting Secret Key Server TimeOut Waiting Time of Accounting Server Max Request Repeat time of accounting request Session Timeout Idle Timeout Available time of session status Available time of Idle status 31 Interim Interval Frequent time of accounting packet (8) “SNMP” page shows the information of setting SNMP. [Figure 42. SNMP Page] ITEM Activate Description Enable/Disable Read Community Name Setting Reading authority Write Community Name Setting Writing authority System Name Setting system name System Contact Setting system contact System Location Setting system location Trap Community Name Setting Trap community 32 1st Trap Server IP Setting 1st Trap Server IP 2nd Trap Server IP Setting 2nd Trap Server IP Auth. Fall Trap Warning message to Trap server Cold Start Trap First booting message to Trap server Link UP Trap Normal status message to Trap server Link Down Trap Abnormal status message to Trap server (9) “SNTP” page shows the information of setting SNTP. [Figure 43. SNTP Page] ITEM Operation SNTP Sever Address Time Zone Description Enable/Disable: SNTP on-off Setting SNTP server Setting SNTP time zone 33 (10) “System” page shows the information of System. [Figure 44. System Page] ITEM Admin Name Admin Password HTTP Port Telnet Daemon Description Name of Administrator Setting Admin password HTTP Port number Enable/Disable Telnet (11) “Reboot” page makes MM-5500PRO reboot. 34 [Figure 45. Reboot Page] ITEM Description Reboot System Reboot MM-5500PRO (All document finished) 35 Thank you.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 35 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:19e0bf4f-a65e-41c9-afc2-e836dba9e41f Producer : Acrobat Distiller 6.0.1 (Windows) Company : fortran Source Modified : D:20050829224036 Headline : Creator Tool : Acrobat PDFMaker 6.0 for Word Modify Date : 2005:08:29 17:24:31-07:00 Create Date : 2005:08:30 08:40:44+10:00 Metadata Date : 2005:08:29 17:24:31-07:00 Document ID : uuid:605c7e33-a721-4d66-97c2-c1dc33b15494 Version ID : 5 Format : application/pdf Title : MM-5100 Control Box Creator : ljgun Subject : Tagged PDF : Yes Author : ljgunEXIF Metadata provided by EXIF.tools