Maxtronic Co INDY2600 Disk Array User Manual Indy2600 Ch5

Download:
Mirror Download [FCC.gov]
Document ID	261106
Application ID	rqkYGrEpstpgpNmSDEq/LQ==
Document Description	users manual 6
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	88.16kB (1102014 bits)
Date Submitted	2002-08-05 00:00:00
Date Available	2002-08-02 00:00:00
Creation Date	2002-07-03 11:47:33
Producing Software	Corel PDF Engine Version 9.397
Document Lastmod	2002-07-24 15:08:59
Document Title	Indy2600-Ch5
Document Creator	CorelDRAW Version 9.397
Document Author:	Maxtronic

Advanced Information
Capacity Expansion
The RAID capacity can be expanded by add one or more Disk
Drive into the existing RAID group and properly setup procedures.
1. Add new HDD into the RAID system.
2. Configuration through the RS-232 Terminal mode, move the
cursor to " On-Line Expand " and " Enable " and press " Enter "
to confirm it.
( If you have not add any new HDD into the RAID group the
" Enable " item will not show up. )
4-22
Chapter 5 : " Hot Swap "
This chapter explains how to remove and install the "Hot-Swap" parts
without interrupting the data access while the disk array is on.
The "Hot-Swap" parts include :
Hard Disk Drives
Redundant Power Supply Units
Cooling Fans
Follow the steps below and refer to the diagrams to remove and
install the "Hot-Swap" parts.
5-1
Hot Swap
Removing / Installing Hard Disk drives
a. Unlock the HDD tray
(When a HDD error occurs, the HDD LED indicator lights up "RED")
ESC
Enter
Figure : Swap HDD ( Unlock )
5-2
Hot Swap
b. Gently pull-out the HDD tray
ESC
Enter
Figure : Swap HDD ( Pull-out )
5-3
Hot Swap
c. Unscrew and unplug the cables
Unplug
Cables
Unscrew
Figure : Swap HDD ( Unplug cables )
5-4
Hot Swap
d. Replace with a new Hard Disk Drive
It must be same capacity or greater than the faulty drive, if you
replace with a Hard disk Drive of insufficient capacity, the Disk
Array's built-in buzzer will sound and the intelligent Auto-Rebuild
function will not be started.
* For best performance, we recommend you swap with an
identical Hard Disk Drive.
e. Gently Slide-in the HDD tray and lock up to start
the Auto-Rebuild
When you have installed the replacement disk drive, screw in all
the screws and plug in the cables, you may now gently slide in
the HDD tray into the chassis and lock up it.
* Data Auto-Rebuild will be started automatically when you lock
up the HDD tray.
ESC
Enter
Figure : Swap HDD ( Lock Up )
5-5
Hot Swap
Removing / Installing the Redundant P/S Unit
There are two LED indicators on the front panel which display the
status of the redundant power supplies. While the power supply
is power-on the #1st LED indicators lights up " Green ", if any one
them fail, the #2nd LED indicator will lights up " Red " and the
power supply's buzzer alarm will sound.
When you need to replace the redundant power supply unit ,
refer to the redundant power supply status LED indicator on the
power supply to find the failed power supply unit ( LED indicator
go off ) and follow these steps to swap it.
a. Unscrew the faulty unit
(For Safety reasons, you should switch off the faulty unit's
power switch)
Unscrew
Switch off
Figure : Swap P/S unit ( Unscrew )
5-6
Hot Swap
b. Replace with a new power supply unit
Figure : Swap P/S unit ( swap with a new unit )
5-7
Hot Swap
c. Press the Power Supply Alarm Reset switch
When you replace a new power supply unit, you should then
push the power supply reset switch to stop the buzzer alarm and
link the two power supply units together.
The new power supply unit will link with the other unit
immediately and will start working after you press the power
supply reset switch, and the buzzer warning noise will stop.
Reset from the rear panel
Reset Here
5-8
Hot Swap
Removing / Installing Cooling Fans
Unscrew the Fan door and open the door.
! Caution : Be careful , the high speed rotating fans may harm
you. Don't touch the rotating Fans, If necessary,
Unplug the Fan power connector first.
Unscrew
Figure : Swap cooling Fan ( Unscrew )
5-9
Hot Swap
Unplug the Fan connector
Unscrew the faulty cooling fan and replace with a
good one
Important ! The cooling fan's air flow must point to the fan
door, please refer to the label on the cooling fan.
Plug in the fan connector, close the fan door
and screw it in
! Caution : The cooling fan will rotate immediately when you
plug in the fan power connector.
The Cooling Fan will only fit in one orientation.
Figure : Swap Cooling Fan ( swap with a new Fan )
5-10
Appendix
Technical Specifications
Microprocessor
Intel i80303 (64-bit RISC processor)
Cache Memory
128MB*
Maximum 512MB
DRAM Slots
Module Type
DRAM Type
DRAM Speed
Parity
Read Cache
Write Cache
One
144 Pin DIMM
SDRAM
PC100/133
Non-Parity
Read-Ahead
Write Back*
Firmware
Flash EEPROM ,256K x 8
SCSI I/O Processor
LSI SYM53C1010
Serial Port
Ba ud Rate
Da ta Bits
Sto p Bit
Pari ty
1x RS232 (Asynchronous) Port
115,200 (Bits Per Second)
None
RAID Levels
0 , 1 , 0+1, 3 or 5
Data Transfer Rate
Up to 160MB/s (Synchronous)
SCSI ID Assignment
0 ~ 14 ( 0* )
Tagged-command queuing
Up to 255 simultaneous data
requests
A-1
Appendix
Interface : Host Channel
Disk Channels
2* Ultra 160 LVD SCSI (68 pin)
16* EIDE ATA-100
Drives
Hot Swap, User Replaceable
Up to Sixteen 3.5" drives ( 1" height )
>2TB
Maximum Fault
Tolerant Capacity
Drive MTBF
>1,000,000 hrs
Host Requirement
Host Independent
Operating Systems
O/S Independent and Transparent
Data Rebuild
Automatic Data Regeneration
LCD Display Panel
2 x 16 Characters
Cooling Fans
12cm DC-Blower
2 Fans
Power Supply Capacity
320W *3 Independent Power
Supplies
AC Input Voltage
90V ~ 260 V ( +/10% ) , 60/50 Hz
Environmental
Relative Humidity
Temperature Operating :
Storage :
Safety testing
Dimensions
Weight
10% to 85% Non-condensing
5 ~ 40
-25 ~ 60
Under apply UL, CE and FCC Class B
483mm(W) * 500mm(D) * 176mm(H)
25 kgs ( W/O Disk Drive )
" * " Default Settings
*** Various trademarks belong to their respective owners.
A-2
Appendix
How to Setup Active Terminator
For better data integrity, we suggest you always add an active
terminator on the Disk Array.
Please follow the Steps below :
1. Plug-in the Terminator before Power-On :
You can find two ports for the host channel adapter on the back
of Disk Array. You can connect the top one with your Host
Computer, and plug in the active terminator on the second one.
2. Turn the Software Termination OFF :
You must "disable" the SCSI terminator on the Disk Array built-in
configuration program.
A. Press the "Enter" button on the front panel to access the built
-in configuration program.
B. Go to " Termination " and select "Disable" than "Save & Restart"
the Disk Array.
Active Terminator
Figure : Active Terminator
2-7
A-3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:07:03 11:47:33
Modify Date                     : 2002:07:24 15:08:59+08:00
Producer                        : Corel PDF Engine Version 9.397
Author                          : Maxtronic
Creator                         : CorelDRAW Version 9.397
Title                           : Indy2600-Ch5
Page Count                      : 14

EXIF Metadata provided by EXIF.tools