Maxtronic Co INDY2600 Disk Array User Manual Indy2600 Ch4

Download:
Mirror Download [FCC.gov]
Document ID	261093
Application ID	rqkYGrEpstpgpNmSDEq/LQ==
Document Description	users manual 5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	132.22kB (1652706 bits)
Date Submitted	2002-08-05 00:00:00
Date Available	2002-08-02 00:00:00
Creation Date	2002-07-03 11:47:10
Producing Software	Corel PDF Engine Version 9.397
Document Lastmod	2002-07-24 15:07:27
Document Title	Indy2600-Ch4
Document Creator	CorelDRAW Version 9.397
Document Author:	Maxtronic

Chapter 4 : " Advanced Information "
This chapter describes more information about your Disk Array. The
following items are describes in detail.
Memory Expansion
RAID Controller
Updating Firmware
Capacity Expansion (On-Line Expand)
4-1
Advanced Information
Memory Expansion
Your Disk Array comes with 128MB of memory that is expandable
to a maximum of 512MB.
These expansion memory module can be purchased from your
dealer.
Memory Type : 3.3V PC100/133 SDRAM 144pin DIMM.
Memory Size : Supports 144pin DIMMs of 64MB, 128MB, 256MB
or 512MB.
Height : 1.15 Inches ( 29.2 mm ).
64MB
8(8Mx8), 8(4Mx16) or 4(8Mx16)
128MB
16(8Mx8), 8(16Mx8), 8(8Mx16) or 4(16Mx16)
256MB
16(16Mx8), 8(32Mx8) or 8(16Mx16)
512MB
16(32Mx8)
1.15"
(29.2mm)
4-2
Advanced Information
Installing Memory Module :
1. Unscrew & Remove cover
Unscrews
ESC
Enter
Figure : Remove Cover
2. Remove the Internal SCSI Host Cable
Internal SCSI
Host 2 Cable
Internal SCSI
Host 1 Cable
Figure : Remove SCSI Cable
4-3
Advanced Information
3. Remove the RAID Controller Set
a. Remove the RAID Controller's Holder screws
b. Push the RAID Controller Set toward to the front panel to
release the Controller Set from the Back Panel PCB.
Figure : Remove the RAID Controller
4-4
Advanced Information
4. Separate the Controller
a. Separated the Controller's main board and the daughter
board.
b. Remove the DIMM Memory from the RAM socket.
Daughter Board
RAM Socket
Main Board
Figure : Separate RAID Controller
4-5
Advanced Information
5. Install the memory
a. The DIMM memory modules will only fit in one orientation.
b. Press the memory module firmly into socket from a 45 degree
angle, make sure that all the contacts are aligned with the
socket.
c. Push the memory module forward to a horizontal position.
RAM Socket
Main Board
Host Channel #2
Host Channel #1
Figure : RAID Controller
4-6
Advanced Information
Disk Array Controller Block Diagram
i80303
RISC
Microprocessor
Main
memory
Flash
EPROM
i80303 Local BUS
NVRAM
LCD
PCI
Bridge
RS232
Terminal
Port
PCI BUS
Dual
Ultra 160
Wide
SCSI
controller
Dual Dual Dual Dual Dual Dual Dual Dual
Channel
Channel
Channel
Channel
Channel
Channel
Channel
Channel
IDE IDE IDE IDE IDE IDE IDE IDE
Controller
Controller
Controller
Controller
Controller
Controller
Controller
Controller
DiskDiskDiskDiskDiskDisk
#1 #2 #3 #4 #5 #6
Dual
Host
Channel
4-7
Disk Disk
# 15 # 16
Advanced Information
Updating Firmware
1. Setup your VT100 Terminal
Please configure the VT100 terminal setting to the values shown
below :
VT100 terminal ( or compatible ) set up
Connection
Serial Port ( COM1 or COM2 )
Protocol
RS232 ( Asynchronous )
Cabling
Null-Modem cable
Baud Rate
115,200
Data Bits
Stop Bit
Parity
None
4-8
Advanced Information
Setup VT100 Terminal
Example : Setup VT100 Terminal in Windows 95
Step 1.
4-9
Advanced Information
Step 2.
4-10
Advanced Information
Step 3. Enter a name for your Terminal.
4-11
Advanced Information
Step 4. Select a connecting port in your Terminal.
4-12
Advanced Information
Step 5. Port parameter settings
4-13
Advanced Information
Step 6.
4-14
Advanced Information
Step 7. Select emulate VT100 mode
After you have finished the VT100 Terminal setup, you may restart
your Disk Array and press " Ctrl + D " keys ( in your Terminal )to link
the Disk Array and Terminal together.
Press
Ctrl
to display the disk array Monitor Utility
screen on your VT100 Terminal.
4-15
Advanced Information
Start to Update Firmware
1. Move the cursor to " Update ROM " and press "Enter".
Warning !
Unpredictable results will occur if firmware update is attempted
during Host computer and Disk Array activity. All activity to the
controller should be stopped before updating firmware.
4-16
Advanced Information
2. Press " Y " to download the new firmware and
press " Y " again to confirm the Update.
4-17
Advanced Information
3. Select transfer " Send Text File " and press Enter.
4-18
Advanced Information
4. Locate the new Firmware file on your PC.
4-19
Advanced Information
5. Press " Go " to confirm to download the new firmware.
4-20
Advanced Information
6. Type " Go " to reconfirm and the firmware will begin to be
reprogrammed.
7. After verifying, please Restart the Disk Array to activate the
new firmware.
4-21

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:07:03 11:47:10
Modify Date                     : 2002:07:24 15:07:27+08:00
Producer                        : Corel PDF Engine Version 9.397
Author                          : Maxtronic
Creator                         : CorelDRAW Version 9.397
Title                           : Indy2600-Ch4
Page Count                      : 21

EXIF Metadata provided by EXIF.tools