Merrytek Technology MC603S Microwave Motion Sensor User Manual 2AI53 MC603S MC603S Manual

Download:
Mirror Download [FCC.gov]
Document ID	3815118
Application ID	2g+3Ft/drxCvLl0tVKqhuA==
Document Description	2AI53-MC603S_MC603S Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.72kB (546562 bits)
Date Submitted	2018-04-12 00:00:00
Date Available	2018-04-13 00:00:00
Creation Date	2018-03-27 14:51:17
Producing Software	Corel PDF Engine Version 17.4.0.887
Document Lastmod	2018-03-27 14:51:17
Document Title	MC603S 说明书---开发用.cdr
Document Creator	CorelDRAW X7
Document Author:	Administrator

MC603S
FCC Warnning:
MICROWAVE MOTION SENSOR USER’S MANUAL
Model No.: MC603S
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator &
your body.
US
GENERAL
GUIDELINES
FOR
INSTALLATION
FEATURES
Automatic switching based on motion and light level.
1, The sensor should be installed by a qualified electrician. And ensure
Zero-crossing point operation helps protect the sensor against
that the electricity supply is switched off before installing or servicing
in-rush current.
the product.
Super Compact size makes it suitable to fix within most
luminaires.
2, The sensor should not be modified in any way. Any modifications
4-pole press-in terminal (L, N, N, L'), easy assembly.
made for this product will immediately invalidate any warranties issued.
Detection area, time delay and daylight threshold can be
precisely set via DIP switch.
3, The company does not accept responsibility for any consequences
resulting from unauthorized modification of the product.
4, The sensor should be connected to a stable power supply of 220240Vac 50Hz/60Hz.
5, Microwaves cannot pass through metal or brick walls if thicker than
20cm. They will pass through thinner walls but there will be some
attenuation.
Operating voltage
120/277Vac, 50/60Hz
Rated load
200W@120Vac 400W@277Vac-Ballast
6, Installation inside a glass or plastic housing will result in a reduction of
400W@120Vac 800W@ 277Vac-Resistive
detection sensitivity. Expect a reduction of approximately 20% for every
HF system
5.8GHz±75MHz, ISM wave band
Transmitting power
<0.5mW
Power consumption

≤0.5W(standby)
Detection zone
Max.(D x H): 10m x 6m
Detection sensitivity
10% / 50% / 75% / 100%
Hold time
5s / 30s / 90s / 3min / 20min / 30min
Daylight sensor
2lux / 10lux / 25lux / 50lux / Disable
Mounting height
6m Max.
3mm of thickness.
INSTALLATION & WIRING
The sensor has 7-position terminal block as Pic 1:
L(Phase) N(Neutral) L
(Switched phase / control)
Motion detection
0.5~3m/s
1-10V (Connected to 1-10V interface) Sync
Detection angle
150°(wall installation)
(synchronization)
360°(ceiling installation)
Operating temperature
-25℃~60℃
IP rating
IP20
Pic 1
The sensor is designed for installation at 2.5-12m in height.
SETTINGS
WIRING SCHEME
Detection area, hold time and daylight sensor can be set by using DIP switches
on the sensor. Note that reducing the detection area will also reduce the sensitivity.
FOR ON/OFF FUNCTION :
Connect to normal control gears (normal LED drivers or ballasts), the wiring as
following:
1, Detection area
I: up to 100%
II: up to 75%
III: up to 50%
IV: up to 10%
Control gear
Control gear
Control gear
Max. 400W
L N
2, Hold time
Refers to the time period the lamp remains at
100% illumination after no motion is detected.
I: 5s
II: 30s
III: 90s
IV: 3min
V: 20min
VI:30min
1 2
ON
Ⅰ
Ⅱ
Ⅲ
Ⅳ
ON ON 100%
ON 75%
50%
ON
10%
3 4 5
ON
Ⅰ
Ⅱ
Ⅲ
Ⅳ
Ⅴ
Ⅳ
ON ON ON
5s
ON ON 30s
ON
ON 90s
ON 3min
ON ON
20min
30min
When set to 30min,The sensor function will be inactive,
the light will go back to normal one.
3,Daylight sensor
The sensor can be set to only allow the lamp to
illuminate below a defined ambient brightness
threshold. The settings are as follows:
DETECTION PATTERN
14
12
10
ON
100%
75%
100%
75%
50%
50%
10%
10%
10
12
14
I: 2lux, darkness operation only
II: 10lux, darkness operation only
III: 25lux, twilight operation
IV: 50lux, twilight operation
V: Disable
6 7 8
Ⅰ ON ON ON 2lux
10lux
Ⅱ ON ON
ON
Ⅲ
25lux
50lux
Ⅳ ON
Disable
Ⅴ
10
12
14
Wall mounting pattern (Unit: m)
Suggested installation height: 1-1.8m
Ceiling mounting pattern (Unit: m)
Suggested installation height: 2.5-6m
*When set to Disable, the daylight sensor will switch on the lamp when motion
is detected regardless of ambient light levels.
*It should be set to Disable mode if the motion sensor is connected to
stand-alone daylight sensors.
4,Stand-by dimming level
When set to “Const-ant ON”, the microwave
sensor function is inactive, lights turns on or
off by switch.
When set to Sensor, the microwave sensor
function is active.
ON
Constant ON
FAQ
Question
The load will
not illuminate
Incorrect daylight
sensor setting selected.
Adjust setting.
Load has failed.
Replace load.
Power is switched off.
Switch on.
Continuous movement in the
detection area.
Check detection area setting.
The load is
permanently The lamp (containing sensor) is
illuminated. installed in an area too close to
reflective surfaces, i.e. metal,
glass or concrete walls.
The load will
not illuminate
despite
movement.
Remedy
Cause
Speed of moving object is not in
the range of 0.5-3m/s or the
detection radius is too small.
1, Make sure installation area
suitable with at least 30cm space
between lamp and surrounding
reflective surfaces.
2, Reduce sensitivity (detection area).
Check detection area setting.
Shenzhen Merrytek Technology Co..Ltd
No.3 Building, 380 Xiangshan Avenue, No.3 Industrial Park Luotian, Songgang Town, Bao’an District, Shenzhen 518105, Guangdong, China
www.merrytek.com Email:sales@merrytek.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Profile CMM Type                : Linotronic
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : Hewlett-Packard
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : Hewlett-Packard
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 2
Create Date                     : 2018:03:27 14:51:17+08:00
Modify Date                     : 2018:03:27 14:51:17+08:00
Producer                        : Corel PDF Engine Version 17.4.0.887
Author                          : Administrator
Creator                         : CorelDRAW X7
Title                           : MC603S 说明书---开发用.cdr

EXIF Metadata provided by EXIF.tools