Meru Networks AP150 Wireless Access Point (Dual Radio Version) User Manual AP Install

Meru Networks Inc. Wireless Access Point (Dual Radio Version) AP Install

Contents

users manual

Meru Access PointInstallation GuideCopyright © Meru Networks, Inc., 2003–2005. All rights reserved.Other names and brands may be claimed as the property of others.Document Number: 882-70031 Rev. A
Contents iii ContentsAbout This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ixAudience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ixIn This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ixOther Sources of Information . . . . . . . . . . . . . . . . . . . . . . . . ixMeru Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . ixExternal References . . . . . . . . . . . . . . . . . . . . . . . . . . xTypographic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . xContacting Meru . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xCustomer Services and Support . . . . . . . . . . . . . . . . . . . . . . xFCC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiDeclaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . xiChapter 1About Meru Access Points . . . . . . . . . . . . . . . . . . . . . . . . . 1Meru Access Point Features . . . . . . . . . . . . . . . . . . . . . . . . . 1Meru Access Point Models . . . . . . . . . . . . . . . . . . . . . . . . . 2AP200. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2AP150. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Chapter 2Installing the AP200. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5FCC Safety Compliance Statement . . . . . . . . . . . . . . . . . . . . 5General Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . 5Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Unpacking the AP200 . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Installation Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 7Installing the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . 10Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . 10Attaching the AP200 Antennas . . . . . . . . . . . . . . . . . . . . . . 11Mounting the Access Point. . . . . . . . . . . . . . . . . . . . . . . . 11Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . 19Checking LED Activity . . . . . . . . . . . . . . . . . . . . . . . . . . 19Ethernet Connector LEDs . . . . . . . . . . . . . . . . . . . . . . . . 19AP200 Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 20Chapter 3Installing the AP150. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23FCC Safety Compliance Statement . . . . . . . . . . . . . . . . . . . . 23General Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . 23Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
iv Meru Access Point Installation Guide Unpacking the AP150 . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 26Installing the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . 29Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . . 29Attaching the AP150 Antennas . . . . . . . . . . . . . . . . . . . . . . 30Mounting the Access Point . . . . . . . . . . . . . . . . . . . . . . . 30Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . 38Checking LED Activity . . . . . . . . . . . . . . . . . . . . . . . . . . 38Ethernet Connector LEDs . . . . . . . . . . . . . . . . . . . . . . . . 38AP150 Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 39Appendix ASpecifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43FCC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Wireless Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Appendix BRegulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . 47Safety Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Federal Communications Commission (FCC) Declaration of Conformity (DoC) & Instructions48 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . 48Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49List of Regulatory Compliance Certifications Summary by Country . . . . . . . . . 50Appendix CTranslated Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . 53Dipole Antenna Installation Warning . . . . . . . . . . . . . . . . . . . . . 54Explosive Device Proximity Warning. . . . . . . . . . . . . . . . . . . . . 55Installation Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Circuit Breaker (15A) Warning . . . . . . . . . . . . . . . . . . . . . . . 57Appendix DChannels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59IEEE 802.11a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59IEEE 802.11b/g . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
List of Figures v List of Figures Figure 1 Meru Wireless LAN (WLAN) ..................................................................................1 Figure 2 AP200 .......................................................................................................................3 Figure 3 AP150 .......................................................................................................................4 Figure 4 AP200 Mounting Bracket .........................................................................................7 Figure 5 AP200 Antenna Connection .....................................................................................12 Figure 6 AP200 Connector Panel ............................................................................................12 Figure 7 AP200 Bracket ..........................................................................................................13 Figure 8 Aligning the AP200 with the Bracket .......................................................................14 Figure 9 Sliding the AP200 into the Bracket ..........................................................................14 Figure 10 Mounting the AP200 to a Suspended Ceiling Rail .................................................15 Figure 11 Mounting the AP200 Above a Suspended Ceiling .................................................17 Figure 12 Box Hanger Mounting Bracket Holes ....................................................................17 Figure 13 Attaching the Mounting Bracket to the Box Hanger ..............................................18 Figure 14 RJ-45 LEDs ............................................................................................................19 Figure 15 AP200 Status LEDs ................................................................................................20 Figure 16 AP150 with Mounting Bracket ...............................................................................26 Figure 17 AP150 Antenna Connection ...................................................................................31 Figure 18 AP150 Connector Panel ..........................................................................................31 Figure 19 AP150 Bracket ........................................................................................................32 Figure 20 Aligning the AP150 with the Bracket .....................................................................33 Figure 21 Sliding the AP150 into the Bracket ........................................................................33 Figure 22 Mounting the AP150 to a Suspended Ceiling Rail .................................................34 Figure 23 Mounting the AP150 Above a Suspended Ceiling .................................................36 Figure 24 Box Hanger Mounting Bracket Holes ....................................................................36 Figure 25 Attaching the Mounting Bracket to the Box Hanger ..............................................37 Figure 26 RJ-45 LEDs ............................................................................................................38 Figure 27 AP150 Status LEDs ................................................................................................39
vi Meru Access Point Installation Guide
List of Tables vii List of TablesTable 1 AP200 Installation Items.......................................................................................... 9Table 2 AP200 Installation Tools ......................................................................................... 9Table 3 AP200 LED Descriptions ........................................................................................ 21Table 4 AP200-Controller Status Information...................................................................... 21Table 5 AP150 Installation Items.......................................................................................... 28Table 6 AP150 Installation Tools ......................................................................................... 28Table 7 AP150 LED Descriptions ........................................................................................ 40Table 8 AP150-Controller Status Information...................................................................... 40Table 9 AP100 Wireless Interface Specifications................................................................. 44Table 10 AP200 Wireless Interface Specifications............................................................... 44Table 11 IEEE 802.11a Channels ......................................................................................... 59Table 12 IEEE 802.11b/g Channels...................................................................................... 60
viii Meru Controller Installation Guide
Audience About This Guide ix About This GuideThis guide describes the features of the Meru Access Point family, which includes the AP200 and AP100 models. This guide also includes the hardware installation for both access points. The term access point is used interchangeably throughout this document to apply to either model when there are no differences between the models.AudienceThis guide is intended for persons installing the Meru Access Point (AP).In This GuideThis guide includes the following chapters:zChapter 1, “About Meru Access Points”zChapter 2, “Installing the AP100”zChapter 2, “Installing the AP200”Other Sources of InformationAdditional information is available in the following Meru publications and external references.Meru PublicationszMeru Wireless LAN System Release NoteszMeru Wireless LAN System Getting Started GuidezMeru Controller Installation GuidezMeru Wireless LAN System Configuration GuidezMeru Wireless LAN System Command Reference
xMeru Access Point Installation GuideTypographic Conventions External ReferenceszStevens, W. R. 1994. TCP/IP Illustrated, Volume 1, The Protocols. Addison-Wesley, Reading, Mass.zGast, M.S. 2002. 802.11 Wireless Networks, The Definitive Guide. O’Reilly and Associates, Sebastopol, Calif.Typographic ConventionsThis document uses the following typographic conventions to help you locate and identify information: Contacting Meru You can visit Meru Networks on the Internet at this URL:http://www.merunetworks.comClick the Support menu button to view Meru Customer Services and Support information.Customer Services and SupportFor assistance, contact Meru Customer Services and Support 24 hours a day at 1-888-637-8952 (1-888-Meru-WLA(N)) or 1-408-215-5305. Email can be sent to support@merunetworks.com.Meru Customer Services and Support provide end users and channel partners with the following:zTelephone technical supportzSoftware update supportzSpare parts and repair serviceNote:Provides extra information, tips, and hints regarding the topic.Caution!Identifies important information about actions that could result in damage to or loss of data, or could cause the application to behave in unexpected ways.Warning! Identifies critical information about actions that could result in equipment failure or bodily harm.
FCC Compliance About This Guide xi RMA ProceduresContact Meru Customer Services and Support for a Return Material Authorization (RMA) for any Meru equipment.Please have the following available when making a call:zCompany and contact informationzEquipment model and serial numberszMeru software release and revision numbers (for example, 3.0.0-35)zA description of the symptoms the problem is manifestingzNetwork configurationFCC ComplianceThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Declaration of ConformityThe AP150 complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC by conforming to the following standards:zSafety: EN 60950:1992 + A1, A2zEMC: EN 55022, EN 50082-1The AP200 complies the with following standards:zRadio: EN 301.893zEMC: EN 301.489-1, EN 489-17zSafety: EN 60950The following CE mark is affixed to the AP100 802.11b with 100 mW radios:Caution!Changes or modifications to the Meru Access Point that are not expressly approved by Meru Networks will void your warranty and could void your authority to operate this equipment.
xii Meru Access Point Installation GuideFCC Compliance Note:This equipment can be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contract Meru Networks.Note:Combinations of power levels and antennas resulting in a radiated power level above 100 mW equivalent isotropic radiated power (EIRP) are considered as not compliant with the above mentioned directive and are not allowed for use with the European community and other countries that have adopted the European R&TTE directive 1999/5/EC or the CEPT recommendation Rec 70.03 or both. The following CE mark is affixed to the AP200 802.11a with 40 mW radios:
Meru Access Point Features About Meru Access Points 1 Chapter 1About Meru Access PointsThe Meru Access Point radio devices communicate with the Meru Controller and form the Wireless LAN (WLAN). The Meru Controller and Access Points connect to the site’s wired LAN through wired switches. Wireless clients associate with the Access Points as they roam throughout the WLAN. As such, the Meru WLAN is an extension of the wired LAN, providing the wireless benefits of client mobility, enhanced access, and dynamic network configuration. Figure 1: Meru Wireless LAN (WLAN)Meru Access Point FeaturesAll Meru Access Points provide the following features:zFive times more voice calls per Access PointMeru Access Points use Over-The-Air QoS to provide fine-grained quality of service on a per-application, per-user, and per-flow basis providing a robust platform for enterprise-quality voice, plus streaming media and data applications. It provides both uplink and downlink QoS between the client and the access point, which is then integrated into the wired QoS mechanisms to provide Meru AP
2Meru Access Point Installation GuideMeru Access Point Models end-to-end QoS. Meru Access points deliver a 5-fold increase in voice carrying capacity from the current 5-8 calls per access point to over 30 calls per Meru Access Point with no change to the 802.11 client.zOver five times the scalability of alternate Access PointsMeru Access Points are unique in their ability to dramatically increase performance over alternate APs, even as client density increases. Meru Access Points, can serve over 100 standard 802.11 active data and voice clients per access point, whereas today's systems are limited to about 10-15 data-only clients. This scalability allows corporations to plan for a wireless usage growth without forklift upgrades to the WLAN infrastructure.zZero-loss handoff means applications are not interruptedMultiple Access Points can be aggregated into a Virtual AP, creating a single wireless network with a wide coverage area that can encompass the entire enterprise campus and provide unparalleled performance and manageability. This breakthrough technology works with any standard 802.11 client device and enables application and security policy persistence while roaming, without requiring the user to re-login or re-authenticate throughout the network coverage area.zEmbedded RF monitor for enhanced securityTraditional approaches to wireless security involve separate devices to monitor the air or legacy APs, or access points that periodically become air monitors. Meru Access Points provide continuous RF monitoring, as well as capture information about all devices that the AP can hear, including clients associated with the access point. Meru WLAN Radar—a third generation rogue AP detection software, provides rogue detection and suppression continuously and without any interruption to the VPN sessions and time-sensitive voice applications that operate on the converged wireless LAN in an enterprise. This constant monitoring enables enhanced security with rogue device detection and prevention that is less disruptive and more cost effective than traditional approaches. Meru Access Point ModelsThe Meru Radio Access Point is available in two model families: the Access Point 200 and the Access Point 100.AP200The Meru Dual Radio Access Point 200 family provides two models that conform to the specifications provided by the IEEE 802.11a and 802.11g protocols and provide backward compatibility for the 802.11b protocol. A Meru AP200 works with most standard WiFi clients.zThe AP201 houses a single 802.11a/b/g radio devicezThe AP208 supports a maximum of two radio devices that can simultaneously run two protocols (802.11b, g or bg on interface 1 and 802.11a on interface 2). Alternately the second radio can be configured to run as an RF monitor to the Meru controller, providing real-time status of RF activity to optimize the wireless network.
Meru Access Point Models About Meru Access Points 3 The Access Point 200 (referred hereafter as the AP200, unless specifically referring to the AP201 or AP208) is housed in a metal case with a plastic removable cover. As such, it can be used for plenum installations when the plastic cover is removed.Figure 2: AP200AP150The Meru Access Point 150 family (referred to hereafter as the AP150, unless specifically referring to the AP150-P) consists of the non-plenum AP150 and plenum-rated AP150-P. Both models that conform to the specifications provided by the IEEE 802.11b protocol and work with all standard WiFi clients. The AP150 also serves as an RF monitor to the Meru controller and provides real-time status of RF activity to optimize the wireless network.AP20000109
4Meru Access Point Installation GuideMeru Access Point Models Figure 3: AP150 00030
Safety Precautions Installing the AP200 5 Chapter 2Installing the AP200This chapter describes how to physically install the Meru AP200. It contains the following sections:zSafety PrecautionszUnpacking the AP200zInstallation RequirementszInstalling the Access PointzWhere to Go From HerezChecking LED ActivitySafety PrecautionsFollow the guidelines in this section to ensure proper operation and safe use of the access point.FCC Safety Compliance StatementThe FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved Meru access point antennas, Meru AP200 products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.General Safety GuidelineszDo not touch or move antenna(s) while the unit is transmitting or receiving.zDo not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.zThe use of wireless devices in hazardous locations is limited to the constraints posed by the local codes, the national codes, and the safety directors of such environments.
6Meru Access Point Installation GuideUnpacking the AP200 WarningsTranslated versions of the following safety warnings are provided in Appendix C.Unpacking the AP200The AP200 ships with a mounting bracket and mounting hardware for standard wall mounting. Optional mounting kits are available for mounting the AP200 above or below a hanging ceiling. The AP200 mounting studs are placed so they can be used with brackets supplied by other vendors or to replace an AP100.Note:The AP200 has a security cable slot so you can secure the AP200 with a standard security cable, such as those used to secure laptop computers.Warning! In order to comply with FCC radio frequency (RF) exposure limits, dipole antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.Warning! Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.Warning! Do not work on the system or connect or disconnect cables during periods of lightning activity.Warning! Read the installation instructions before you connect the system to its power source.Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).Warning! Inside antennas must be positioned to observe minimum separation of 20 cm. (~ 8 in.) from all users and bystanders. For the protection of personnel working in the vicinity of inside (downlink) antennas, the following guidelines for minimum distances between the human body and the antenna must be observed. The installation of the indoor antenna must be such that, under normal conditions, all personnel cannot come within 20 cm. (~ 8.0 in.) from any inside antenna. Exceeding this minimum separation will ensure that the employee or bystander does not receive RF-exposure beyond the Maximum Permissible Exposure according to FCC CFR 47, section 1.1310 i.e. limits for General Population/Uncontrolled Exposure.
Installation Requirements Installing the AP200 7 An array of holes on the mounting bracket (see Figure 4) allow it to be mounted on the wall and over junction boxes or molly bolts. There are also holes for passing the PoE Ethernet or external power supply cable through the bracket if the bracket is mounted on a junction box or over the ceiling T-bar box hanger. Confirm that the AP200 shipping package contains the following items:zAccess point zMounting bracket with two mounting screwszCD-ROM of Meru Wireless LAN System documentationzOptional suspended ceiling mounting hardware kitzOptional T-bar box hanger hardware kit for mounting above a suspended ceilingFigure 4: AP200 Mounting BracketInstallation RequirementsThe following recommended mounting locations provide the best reception for the AP200:zOn a horizontal surface, such as a table or a deskzOn a vertical surface, usually a wallzBelow a hanging ceilingAccess point mountCeiling mount holeCeiling mount holeAccess point mountAccess point mountLocking detentWall cable accessSuspended ceilingcable access00100
8Meru Access Point Installation GuideInstallation Requirements zAbove a hanging ceiling tiles (this installation is supported only for the AP200 with the plastic enclosure removed)Suitable for use in environmental air space in accordance with the Section 300-22(c) of the National Electric Code and Sections 2- 128.12 - 010 (3) and 12 - 100 of the Canadian Electrical Code. Part 1. C22. 1. (For AP200 with plastic enclosure removed.)To complete this installation, you need the items listed in Tabl e 1.
Installation Requirements Installing the AP200 9 Table 1: AP200 Installation ItemsYou need the tools listed in Table 2 .Table 2: AP200 Installation ToolsInstallation Type Consumable Items RequiredHorizontal mounting NoneVertical mounting over a wall stud zTwo #6 x 2" wood screws for a wood stud; or zTwo #6 x 1½" metal screws for a metal studzMounting bracketVertical mounting on sheetrock zTwo #6 x 1" screwszTwo #4-6 x 7/8" ribbed plastic wall anchorszMounting bracketHorizontal mounting below a hanging ceilingzTwo caddy fastenerszTwo plastic spacerszTwo keps nuts (with attached lock washer)zMounting bracketMounting above a ceiling tile (AP200 metal enclosure only)zTwo T-rail clipszOne T-box hangerzOne bracket mounting clipzMounting bracketInstallation Type Tools RequiredHorizontal mounting NoneVertical mounting over a wall stud zDrill z1/8"drill bitzScrewdriverVertical mounting on sheetrock zDrillz3/16" drill bitzScrewdriver
10 Meru Access Point Installation GuideInstalling the Access Point Installing the Access PointSelecting a LocationThe AP200 requires a location that meets the following:zRelatively unobstructed access to the stations the AP serveszPower over Ethernet (PoE) connection to the network switch servicing the controller.APs can obtain their power from 802.3af standard Power over Ethernet (PoE) or external power supply. If an external power supply is utilized to power the AP200, ensure that it is a Listed power supply, marked "Class 2" or "LPS" (Limited Power Source), and rated a minimum of 3.3 V, 4 A. For PoE, the power can be supplied by a PoE-compatible network switch or PoE power injector installed between the switch and the AP200. Select a location with minimal physical obstructions between the AP and the wireless stations. In an office with cubicles, mounting the APs below a hanging ceiling or the wall near the ceiling provides the least obstructed communications path. For an external power supply connection, ensure the power source is near to where the AP200 will be mounted.Most installations receive the best coverage using the following guidelines:Install APs toward the center of the building.zDo not install APs near metal objects, such as heating ducts, metal doors, or electric service panels.zRelative to the ground, orient the antenna up or down, not sideways.The AP200 is only intended for installation in Environment A as defined in IEEE 802.3af. All interconnected equipment must be contained within the same building, including the interconnected equipment's associated LAN connection.Horizontal mounting below a hanging ceilingzScrewdriverzWrench or pliersMounting above a hanging ceiling (AP200 metal enclosure only)zWrench or plierszScrewdriverInstallation Type Tools RequiredNote:The previous guidelines are general guidelines. Each site has its own unique environment. Place access points accordingly.
Installing the Access Point Installing the AP200 11 Attaching the AP200 AntennasThe AP200 is provided with external antenna ports. Make sure that all external antennas and their associated wiring are located entirely indoors. The external antennas are not suitable for outside use.If the AP200 does not have external antennas, attach the antennas to the connectors on the AP200 (see Figure 5). Rotate the knurled ring at the base of the antenna clockwise to attach the antenna. The ring should be finger-tight.Mounting the Access PointYou can mount an AP200 in the following ways:zHorizontally, as described in the “Horizontal Mounting” section.zVertically, as described in the “Vertical Mounting” section.zBelow a hanging ceiling, as described in the “Mounting Below a Suspended Ceiling” section.zAbove a tiled hanging ceiling, as described in the “Mounting Above a Suspended Ceiling” section.Horizontal MountingTo horizontally mount an AP200:1. Place the AP200 flat on the horizontal surface.2. For each antenna, loosen the knurled ring at the base of the antenna (see Figure 5), point the antenna straight up, then retighten the ring.Caution!When changing the orientation of the antennas, be sure to slightly loosen the knurled ring before moving the antenna. Retighten the ring afterward. Otherwise, you might damage the internal cabling in the AP.
12 Meru Access Point Installation GuideInstalling the Access Point Figure 5: AP200 Antenna Connection3. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in Figure 6.Figure 6: AP200 Connector PanelVertical MountingTo vertically mount an AP:1. Using the bracket holes as a template, mark the location on the wall for the two AP bracket mounting screws. They are placed 4 ½ inches apart, center-to-center, one above the other. If you are not using plastic wall anchors, you must center the mounting screws on a wall stud. If you do not center the mounting screws on a wall stud, you must use plastic wall anchors.Turn clockwiseto tightenAntennaAccess Point 200ETHERNET3.3 VDC ANT 200110Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.CONSOLEANT 1 ANT 23.3 VDCETHERNET00108100/1000Ethernet(Reserved) ConsoleportAntenna 1 Antenna 2PowerinletReset (Push to restore default settings) (Reserved)
Installing the Access Point Installing the AP200 13 Figure 7: AP200 Bracket2. Drill holes at the locations you marked:—3/16-inch holes if you are using plastic anchors—1/8-inch holes if you are using only the screws3. If you are using plastic anchors, install them in the holes.4. Screw in the screws most of the way, so that the screw head is about 1/16 of an inch from the wall.5. Mount the bracket on the screws, placing the circular portion of the keyhole mounts over the screw heads and sliding the bracket down.6. Tighten the screws to secure the bracket.7. Align the AP200 mounting posts over the circular portion of the keyhole mounts, push the AP in and slide the AP down until it engages with the locking detents. You should hear it snap in place.Access point mountCeiling mount holeCeiling mount holeAccess point mountAccess point mountLocking detentWall cable accessSuspended ceilingcable access00100
14 Meru Access Point Installation GuideInstalling the Access Point Figure 8: Aligning the AP200 with the BracketFigure 9: Sliding the AP200 into the Bracket8. For external antennas, loosen the knurled ring at the base of each antenna (see Figure 5), point the antenna straight up, then retighten the ring.00115Mounting bracket attached to wallAP20000112Mounting bracket
Installing the Access Point Installing the AP200 15 9. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in Figure 6.Mounting Below a Suspended CeilingThe optional suspended ceiling mounting kit allows the AP200 mounting bracket to attach to suspended ceiling T-rails (see Figure 10).Note:To comply with NEC code, attach a grounding wire to any of the screws used to attach the AP200 to the mounting bracket.Figure 10: Mounting the AP200 to a Suspended Ceiling RailTo mount an AP200 below a suspended ceiling:1. Determine the location on the ceiling rail where the AP will be mounted and remove the ceiling tiles.2. Place each of the two caddy fasteners on the ceiling T-rail and twist to attach to the rail.3. Adjust the distance between the caddy fasteners by using the mounting bracket holes as a guide.4. Tighten the caddy fasteners in place using a standard screwdriver. Do not overtighten.5. Place each spacer on the caddy fastener stud. The spacer legs should contact the ceiling T-rail.6. Align the mounting bracket keyholes with the caddy fastener studs and slide the AP200 to the narrow end of the hole.Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.Suspended ceiling T-railMounting bracketKeps nuts with attachedlocking washerCaddy fastener(s)Plastic spacer(s)00102
16 Meru Access Point Installation GuideInstalling the Access Point 7. Attach a keps nut to each caddy fastener stud and hand tighten. Do not overtighten.8. Align the AP200 mounting posts over the circular portion of the keyhole mounts, push the AP in and slide the AP down until it engages with the locking detents (see Figure 9). You should hear it snap in place.9. For each antenna, loosen the knurled ring at the base of the antenna (see Figure 5), point the antenna straight down, then retighten the ring.10. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in (see Figure 6).Mounting Above a Suspended CeilingThe optional T-bar box hanger mounting kit allows the AP200 to be mounted above suspended ceiling T-rails (see Figure 11). The installation attaches the T-bar box hanger to the ceiling rails using clips. The AP200 attaches to the mounting bracket that is attached to the T-bar box hanger. The AP200 antennas should point straight down for this type of installation. You may need to modify thicker tiles to support this installation.Any Fast Ethernet (FE) cables installed in air-handling spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP (Multi Purpose Plenum), or CMP (Communications Plenum).Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.Note:When installed in air-handling spaces, such as above a suspended ceiling, the AP200 is to be powered via PoE only (PoE is required).Note:The AP200 with the metal enclosure exposed meets the requirements for fire resistance and low smoke-generating characteristics required by Section 300-22(C) of the National Electrical Code (NEC) for installation in a building’s environmental air space. You must remove the plastic enclosure to reveal the plenum-rated AP200 metal case for installations above a suspended ceiling. Additionally, you must use Ethernet cable that meets the requirements for operating in environmental air space (in accordance with Section 300-22(C) of the NEC).
Installing the Access Point Installing the AP200 17 Figure 11: Mounting the AP200 Above a Suspended CeilingTo mount an AP200 above suspended ceiling rails:1. Determine the location on the ceiling rails where the AP will be mounted and remove the ceiling tile.2. Unpack the T-bar hanger kit and unfold the legs of the T-bar hanger.3. Locate the bracket mounting clip holes on the mounting bracket (see Figure 12). One hole attaches the bracket perpendicular to the box hanger. The other mounts the bracket parallel to the box hanger.Figure 12: Box Hanger Mounting Bracket Holes4. Attach the U-joint of the clip to the T-bar and snap in place (see Figure 13).Bracket mounting clipMounting bracketT-bar hanger Height adjustment screwHeight adjustment screwSuspended ceiling T-rail T-rail clipsAntennasAccess Point 20000103Mounting bracket holes00101
18 Meru Access Point Installation GuideInstalling the Access Point .Figure 13: Attaching the Mounting Bracket to the Box Hanger5. Pass the long end clip through the large center hole to the underside of the the mounting bracket clip and then attach the bracket to the clip using the supplied screw (see Figure 13 for orientation). 6. Hold the AP200 next to the mounting bracket to estimate the height of the T-bar box hanger to provide enough clearance for the external antennas, which should be pointing down.7. Adjust the height of the box hanger using the height adjusting screws (see Figure 10).8. Clip the box hanger T-rail clips to the ceiling rails, making sure they are securely attached. 9. Connect a drop wire to a building structural element and through the hold provided in the bracket mounting clip. The U.S. National Electrical Safety Code requires this additional support.10. Connect the posts of the AP200 to the three keyholes of the mounting bracket and slide into the keyhole (see Figure 9), ensuring the locking detent is engaged. You will hear a click.11. For each antenna, loosen the knurled ring at the base of the antenna (see Figure 5), point the antenna down, then retighten the ring.12. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in Figure 6. 13. Check that the AP200 is operating correctly before replacing the ceiling tile to the ceiling. Verify correct operating using the LEDs, as shown in the next section.00104Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.
Where to Go From Here Installing the AP200 19 Where to Go From HereNow that the AP200 is installed, go to the Meru Wireless LAN Getting Started Guide for instructions on initializing the controller and connecting the controller and APs to the Ethernet switch to form the WLAN. Return to this section to check the status of the LEDs once the WLAN is operational.Checking LED ActivityAccess point status LEDs are provided on the Ethernet connector and on the face of the AP200. Ethernet Connector LEDsAfter the AP200 is connected, the LEDs near the RJ-45 connector should light, as shown in Figure 14. Figure 14: RJ-45 LEDsThe green LED on the left blinks if any Ethernet activity is taking place. If there is no Ethernet activity, the LED is off. The LED on the right is solid green if an Ethernet link is present. If no Ethernet link is present or connectivity is lost, the LED is off.Ethernet activityLink present00129
20 Meru Access Point Installation GuideChecking LED Activity AP200 Status LEDsFour status LEDs on the face of the AP200 also light, as shown in Figure 15.. Figure 15: AP200 Status LEDsThe functions of the status LEDs are described in Table 4.When the AP200 is first connected to the controller and any time the access point is rebooted there-after, the AP initializes with and then is programmed by the controller. When the AP is first powered up, all LEDs are green. Thereafter, the Status LED (see Figure 15) color reflects the various operating states (Tabl e 4). AP200RF2RF1STATUSPOWER113
Checking LED Activity Installing the AP200 21 Table 3: AP200 LED DescriptionsTable 4: AP200-Controller Status InformationLED FunctionRF 2 The status LED for Radio 2 is a follows:off—no radio presentyellow—radio initializingred—radio failuresolid green—radio OKblinking green—radio activityRF 1 The status LED for Radio 1 is a follows:off—no radio presentyellow—radio initializingred—radio failuresolid green—radio OKblinking green—radio activityStatus AP-Controller operational status (see Table 4)Power green—presence of powerState Interpretation AP200 LED CycleAttempting to discover ControllerIn the process of discovering the controller. The AP is connected but not associated with the con-troller. If the AP does not associate with the con-troller after a period of time, verify that the connection between the AP and the switch or the switch and the controller is unbroken.Green/Red/Blue/RedConnected Normal operation without security. Blue/Blue/Blue/RedBlue/Blue/Blue/Red, for 2 seconds.Authenticated Normal operation with security. Blue blinkaDisconnected Access point was once connected to a controller and configured by the controller, but can no longer find that controllerGreen/Purple/Green/PurpleStandalone Access point is operating in a standalone mode Purple blink
22 Meru Access Point Installation GuideChecking LED Activity Downloading Downloading image or configuration from the controllerGreen/BlueGreen/BlueError State Access point is in an error state. Call Meru technical supportRed (blinking or solid)a. The AP200 LEDs cycle from bright to dim for each “blink.”State Interpretation AP200 LED Cycle
Safety Precautions Installing the AP150 23 Chapter 3Installing the AP150This chapter describes how to physically install the Meru AP150. It contains the following sections:zSafety PrecautionszUnpacking the AP150zInstallation RequirementszInstalling the Access PointzWhere to Go From HerezChecking LED ActivitySafety PrecautionsFollow the guidelines in this section to ensure proper operation and safe use of the access point.FCC Safety Compliance StatementThe FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved Meru access point antennas, Meru AP150 products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.General Safety GuidelineszDo not touch or move antenna(s) while the unit is transmitting or receiving.zDo not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.zThe use of wireless devices in hazardous locations is limited to the constraints posed by the local codes, the national codes, and the safety directors of such environments.
24 Meru Access Point Installation GuideUnpacking the AP150 WarningsTranslated versions of the following safety warnings are provided in Appendix C.Unpacking the AP150The AP150 ships with a mounting bracket and mounting hardware for standard wall mounting. Optional mounting kits are available for mounting the AP150 above or below a hanging ceiling. The AP150 mounting studs are placed so they can be used with brackets supplied by other vendors or to replace an AP100.Note:The AP150 has a security cable slot so you can secure the AP150 with a standard security cable, such as those used to secure laptop computers.Warning! In order to comply with FCC radio frequency (RF) exposure limits, dipole antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.Warning! Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.Warning! Do not work on the system or connect or disconnect cables during periods of lightning activity.Warning! Read the installation instructions before you connect the system to its power source.Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).Warning! Inside antennas must be positioned to observe minimum separation of 20 cm. (~ 8 in.) from all users and bystanders. For the protection of personnel working in the vicinity of inside (downlink) antennas, the following guidelines for minimum distances between the human body and the antenna must be observed. The installation of the indoor antenna must be such that, under normal conditions, all personnel cannot come within 20 cm. (~ 8.0 in.) from any inside antenna. Exceeding this minimum separation will ensure that the employee or bystander does not receive RF-exposure beyond the Maximum Permissible Exposure according to FCC CFR 47, section 1.1310 i.e. limits for General Population/Uncontrolled Exposure.
Unpacking the AP150 Installing the AP150 25 An array of holes on the mounting bracket (see Figure 16) allow it to be mounted on the wall and over junction boxes or molly bolts. There are also holes for passing the PoE Ethernet or external power supply cable through the bracket if the bracket is mounted on a junction box or over the ceiling T-bar box hanger. Confirm that the AP150 shipping package contains the following items:zAccess point zMounting bracket with two mounting screwszCD-ROM of Meru Wireless LAN System documentationzOptional suspended ceiling mounting hardware kitzOptional T-bar box hanger hardware kit for mounting above a suspended ceiling
26 Meru Access Point Installation GuideInstallation Requirements Figure 16: AP150 with Mounting BracketInstallation RequirementsThe following recommended mounting locations provide the best reception for the AP150:zOn a horizontal surface, such as a table or a deskzOn a vertical surface, usually a wallzBelow a hanging ceilingzAbove a hanging ceiling tiles (this installation is supported only for the AP150 with the plastic enclosure removed)00031
Installation Requirements Installing the AP150 27 Suitable for use in environmental air space in accordance with the Section 300-22(c) of the National Electric Code and Sections 2- 128.12 - 010 (3) and 12 - 100 of the Canadian Electrical Code. Part 1. C22. 1. (For AP150 with plastic enclosure removed.)To complete this installation, you need the items listed in Tabl e 5.
28 Meru Access Point Installation GuideInstallation Requirements Table 5: AP150 Installation ItemsYou need the tools listed in Table 6 .Table 6: AP150 Installation ToolsInstallation Type Consumable Items RequiredHorizontal mounting NoneVertical mounting over a wall stud zTwo #6 x 2" wood screws for a wood stud; or zTwo #6 x 1½" metal screws for a metal studzMounting bracketVertical mounting on sheetrock zTwo #6 x 1" screwszTwo #4-6 x 7/8" ribbed plastic wall anchorszMounting bracketHorizontal mounting below a hanging ceilingzTwo caddy fastenerszTwo plastic spacerszTwo keps nuts (with attached lock washer)zMounting bracketMounting above a ceiling tile (AP150 metal enclosure only)zTwo T-rail clipszOne T-box hangerzOne bracket mounting clipzMounting bracketInstallation Type Tools RequiredHorizontal mounting NoneVertical mounting over a wall stud zDrill z1/8"drill bitzScrewdriverVertical mounting on sheetrock zDrillz3/16" drill bitzScrewdriver
Installing the Access Point Installing the AP150 29 Installing the Access PointSelecting a LocationThe AP150 requires a location that meets the following:zRelatively unobstructed access to the stations the AP serveszPower over Ethernet (PoE) connection to the network switch servicing the controller.APs can obtain their power from 802.3af standard Power over Ethernet (PoE) or external power supply. If an external power supply is utilized to power the AP150, ensure that it is a Listed power supply, marked "Class 2" or "LPS" (Limited Power Source), and rated a minimum of 3.3 V, 4 A. For PoE, the power can be supplied by a PoE-compatible network switch or PoE power injector installed between the switch and the AP150. Select a location with minimal physical obstructions between the AP and the wireless stations. In an office with cubicles, mounting the APs below a hanging ceiling or the wall near the ceiling provides the least obstructed communications path. For an external power supply connection, ensure the power source is near to where the AP150 will be mounted.Most installations receive the best coverage using the following guidelines:Install APs toward the center of the building.zDo not install APs near metal objects, such as heating ducts, metal doors, or electric service panels.zRelative to the ground, orient the antenna up or down, not sideways.The AP150 is only intended for installation in Environment A as defined in IEEE 802.3af. All interconnected equipment must be contained within the same building, including the interconnected equipment's associated LAN connection.Horizontal mounting below a hanging ceilingzScrewdriverzWrench or pliersMounting above a hanging ceiling (AP150 metal enclosure only)zWrench or plierszScrewdriverInstallation Type Tools RequiredNote:The previous guidelines are general guidelines. Each site has its own unique environment. Place access points accordingly.
30 Meru Access Point Installation GuideInstalling the Access Point Attaching the AP150 AntennasThe AP150 is provided with external antenna ports. Make sure that all external antennas and their associated wiring are located entirely indoors. The external antennas are not suitable for outside use.If the AP150 does not have external antennas, attach the antennas to the connectors on the AP150 (see Figure 17). Rotate the knurled ring at the base of the antenna clockwise to attach the antenna. The ring should be finger-tight.Mounting the Access PointYou can mount an AP150 in the following ways:zHorizontally, as described in the “Horizontal Mounting” section.zVertically, as described in the “Vertical Mounting” section.zBelow a hanging ceiling, as described in the “Mounting Below a Suspended Ceiling” section.zAbove a tiled hanging ceiling, as described in the “Mounting Above a Suspended Ceiling” section.Horizontal MountingTo horizontally mount an AP150:1. Place the AP150 flat on the horizontal surface.2. For each antenna, loosen the knurled ring at the base of the antenna (see Figure 17), point the antenna straight up, then retighten the ring.Caution!When changing the orientation of the antennas, be sure to slightly loosen the knurled ring before moving the antenna. Retighten the ring afterward. Otherwise, you might damage the internal cabling in the AP.
Installing the Access Point Installing the AP150 31 Figure 17: AP150 Antenna Connection3. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in Figure 18.Figure 18: AP150 Connector PanelVertical MountingTo vertically mount an AP:1. Using the bracket holes as a template, mark the location on the wall for the two AP bracket mounting screws. They are placed 4 ½ inches apart, center-to-center, one above the other. If you are not using plastic wall anchors, you must center the mounting screws on a wall stud. If you do not center the mounting screws on a wall stud, you must use plastic wall anchors.Turn clockwiseto tightenAntennaAccess Point 200ETHERNET3.3 VDC ANT 200110Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.00032Antenna 1 Antenna 2Powerinlet(Reserved)100/1000Ethernet(Reserved) Consoleport Reset (Push to restore default settings)
32 Meru Access Point Installation GuideInstalling the Access Point Figure 19: AP150 Bracket2. Drill holes at the locations you marked:—3/16-inch holes if you are using plastic anchors—1/8-inch holes if you are using only the screws3. If you are using plastic anchors, install them in the holes.4. Screw in the screws most of the way, so that the screw head is about 1/16 of an inch from the wall.5. Mount the bracket on the screws, placing the circular portion of the keyhole mounts over the screw heads and sliding the bracket down.6. Tighten the screws to secure the bracket.7. Align the AP150 mounting posts over the circular portion of the keyhole mounts, push the AP in and slide the AP down until it engages with the locking detents. You should hear it snap in place.00033
Installing the Access Point Installing the AP150 33 Figure 20: Aligning the AP150 with the BracketFigure 21: Sliding the AP150 into the Bracket8. For external antennas, loosen the knurled ring at the base of each antenna (see Figure 17), point the antenna straight up, then retighten the ring.00115Mounting bracket attached to wallAP20000112Mounting bracket
34 Meru Access Point Installation GuideInstalling the Access Point 9. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in Figure 18.Mounting Below a Suspended CeilingThe optional suspended ceiling mounting kit allows the AP150 mounting bracket to attach to suspended ceiling T-rails (see Figure 22).Note:To comply with NEC code, attach a grounding wire to any of the screws used to attach the AP150 to the mounting bracket.Figure 22: Mounting the AP150 to a Suspended Ceiling RailTo mount an AP150 below a suspended ceiling:1. Determine the location on the ceiling rail where the AP will be mounted and remove the ceiling tiles.2. Place each of the two caddy fasteners on the ceiling T-rail and twist to attach to the rail.3. Adjust the distance between the caddy fasteners by using the mounting bracket holes as a guide.4. Tighten the caddy fasteners in place using a standard screwdriver. Do not overtighten.5. Place each spacer on the caddy fastener stud. The spacer legs should contact the ceiling T-rail.6. Align the mounting bracket keyholes with the caddy fastener studs and slide the AP150 to the narrow end of the hole.Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.Suspended ceiling T-railMounting bracketKeps nuts with attachedlocking washerCaddy fastener(s)Plastic spacer(s)00102
Installing the Access Point Installing the AP150 35 7. Attach a keps nut to each caddy fastener stud and hand tighten. Do not overtighten.8. Align the AP150 mounting posts over the circular portion of the keyhole mounts, push the AP in and slide the AP down until it engages with the locking detents (see Figure 21). You should hear it snap in place.9. For each antenna, loosen the knurled ring at the base of the antenna (see Figure 17), point the antenna straight down, then retighten the ring.10. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in (see Figure 18).Mounting Above a Suspended CeilingThe optional T-bar box hanger mounting kit allows the AP150 to be mounted above suspended ceiling T-rails (see Figure 23). The installation attaches the T-bar box hanger to the ceiling rails using clips. The AP150 attaches to the mounting bracket that is attached to the T-bar box hanger. The AP150 antennas should point straight down for this type of installation. You may need to modify thicker tiles to support this installation.Any Fast Ethernet (FE) cables installed in air-handling spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP (Multi Purpose Plenum), or CMP (Communications Plenum).Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.Note:When installed in air-handling spaces, such as above a suspended ceiling, the AP150 is to be powered via PoE only (PoE is required).Note:The AP150 with the metal enclosure exposed meets the requirements for fire resistance and low smoke-generating characteristics required by Section 300-22(C) of the National Electrical Code (NEC) for installation in a building’s environmental air space. You must remove the plastic enclosure to reveal the plenum-rated AP150 metal case for installations above a suspended ceiling. Additionally, you must use Ethernet cable that meets the requirements for operating in environmental air space (in accordance with Section 300-22(C) of the NEC).
36 Meru Access Point Installation GuideInstalling the Access Point Figure 23: Mounting the AP150 Above a Suspended CeilingTo mount an AP150 above suspended ceiling rails:1. Determine the location on the ceiling rails where the AP will be mounted and remove the ceiling tile.2. Unpack the T-bar hanger kit and unfold the legs of the T-bar hanger.3. Locate the bracket mounting clip holes on the mounting bracket (see Figure 24). One hole attaches the bracket perpendicular to the box hanger. The other mounts the bracket parallel to the box hanger.Figure 24: Box Hanger Mounting Bracket Holes4. Attach the U-joint of the clip to the T-bar and snap in place (see Figure 25).Bracket mounting clipMounting bracketT-bar hanger Height adjustment screwHeight adjustment screwSuspended ceiling T-rail T-rail clipsAntennasAccess Point 20000103Mounting bracket holes00101
Installing the Access Point Installing the AP150 37 .Figure 25: Attaching the Mounting Bracket to the Box Hanger5. Pass the long end clip through the large center hole to the underside of the the mounting bracket clip and then attach the bracket to the clip using the supplied screw (see Figure 25 for orientation). 6. Hold the AP150 next to the mounting bracket to estimate the height of the T-bar box hanger to provide enough clearance for the external antennas, which should be pointing down.7. Adjust the height of the box hanger using the height adjusting screws (see Figure 22).8. Clip the box hanger T-rail clips to the ceiling rails, making sure they are securely attached. 9. Connect a drop wire to a building structural element and through the hold provided in the bracket mounting clip. The U.S. National Electrical Safety Code requires this additional support.10. Connect the posts of the AP150 to the three keyholes of the mounting bracket and slide into the keyhole (see Figure 21), ensuring the locking detent is engaged. You will hear a click.11. For each antenna, loosen the knurled ring at the base of the antenna (see Figure 17), point the antenna down, then retighten the ring.12. Connect one end of the PoE 100BaseT Ethernet cable to the 100/1000 Ethernet connector, shown in Figure 18. 13. Check that the AP150 is operating correctly before replacing the ceiling tile to the ceiling. Verify correct operating using the LEDs, as shown in the next section.00104Caution!Be sure to connect the Ethernet cable to the Ethernet port; the cable can mistakenly be plugged into the Console port.
38 Meru Access Point Installation GuideWhere to Go From Here Where to Go From HereNow that the AP150 is installed, go to the Meru Wireless LAN Getting Started Guide for instructions on initializing the controller and connecting the controller and APs to the Ethernet switch to form the WLAN. Return to this section to check the status of the LEDs once the WLAN is operational.Checking LED ActivityAccess point status LEDs are provided on the Ethernet connector and on the face of the AP150. Ethernet Connector LEDsAfter the AP150 is connected, the LEDs near the RJ-45 connector should light, as shown in Figure 26. Figure 26: RJ-45 LEDsThe green LED on the left blinks if any Ethernet activity is taking place. If there is no Ethernet activity, the LED is off. The LED on the right is solid green if an Ethernet link is present. If no Ethernet link is present or connectivity is lost, the LED is off.Ethernet activityLink present00129
Checking LED Activity Installing the AP150 39 AP150 Status LEDsFour status LEDs on the face of the AP150 also light, as shown in Figure 27.. Figure 27: AP150 Status LEDsThe functions of the status LEDs are described in Table 8.When the AP150 is first connected to the controller and any time the access point is rebooted there-after, the AP initializes with and then is programmed by the controller. When the AP is first powered up, all LEDs are green. Thereafter, the Status LED (see Figure 27) color reflects the various operating states (Tabl e 8). AP200RF2RF1STATUSPOWER113
40 Meru Access Point Installation GuideChecking LED Activity Table 7: AP150 LED DescriptionsTable 8: AP150-Controller Status InformationLED FunctionRF 2 The status LED for Radio 2 is a follows:off—no radio presentyellow—radio initializingred—radio failuresolid green—radio OKblinking green—radio activityRF 1 The status LED for Radio 1 is a follows:off—no radio presentyellow—radio initializingred—radio failuresolid green—radio OKblinking green—radio activityStatus AP-Controller operational status (see Tab le 8)Power green—presence of powerState Interpretation AP150 LED CycleAttempting to discover ControllerIn the process of discovering the controller. The AP is connected but not associated with the con-troller. If the AP does not associate with the con-troller after a period of time, verify that the connection between the AP and the switch or the switch and the controller is unbroken.Green/Red/Blue/RedConnected Normal operation without security. Blue/Blue/Blue/RedBlue/Blue/Blue/Red, for 2 seconds.Authenticated Normal operation with security. Blue blinkaDisconnected Access point was once connected to a controller and configured by the controller, but can no longer find that controllerGreen/Purple/Green/PurpleStandalone Access point is operating in a standalone mode Purple blink
Checking LED Activity Installing the AP150 41 Downloading Downloading image or configuration from the controllerGreen/BlueGreen/BlueError State Access point is in an error state. Call Meru technical supportRed (blinking or solid)a. The AP150 LEDs cycle from bright to dim for each “blink.”State Interpretation AP150 LED Cycle
42 Meru Access Point Installation GuideChecking LED Activity
Specifications 43 Appendix ASpecificationsThis chapter provides specifications for the Meru Access Points and contains the following sections:zFCC CompliancezWireless InterfacezEthernet InterfacezPhysicalFCC ComplianceThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Caution!Changes or modifications to the Meru Access Point that are not expressly approved by Meru Networks will void your warranty and could void your authority to operate this equipment.
44 Meru Access Point Installation GuideWireless Interface Wireless InterfaceTable 9: AP100 Wireless Interface SpecificationsTable 10: AP200 Wireless Interface SpecificationsEthernet InterfaceFeature DetailsWireless Standards z802.11bAntennas zTwo external antennas. Omnidirectional and directional antennas for specific coverage requirementsWireless Medium Access zWiFi Compliant 802.11 MAC standardPower Management zPower-save mode for clients in both QoS mode and non-QoS modeFrame Size zPeak frame size of > 2346 byteszFragmentation and reassembly of 802.11/Ethernet framesClient Activities SupportedzActive scanning and passive scanningzPre-authenticationzPower-save mode supportedFeature DetailsWireless Standards z802.11a, 802.11b, 802.11gAntennas zTwo external antennas. Omnidirectional and directional antennas for specific coverage requirementsWireless Medium Access zWiFi Compliant 802.11 MAC standardPower Management zPower-save mode for clients in both QoS mode and non-QoS modeFrame Size zPeak frame size of > 2346 byteszFragmentation and reassembly of 802.11/Ethernet framesClient Activities SupportedzActive scanning and passive scanningzPre-authenticationzPower-save mode supported
Physical Specifications 45 PhysicalPhysical specifications for Meru Access Points are provided in the access point Data Sheet. Contact your Meru sales engineer for a copy of the document.Feature DetailWireline Standard zOne 10/100 Mbps Ethernet (IEEE 802.3) interface, supporting half-duplex and full-duplex modeszSupports the Power over Ethernet (PoE) IEEE 802.3af standard
46 Meru Access Point Installation GuidePhysical
Regulatory Information 47 Appendix BRegulatory InformationB-1This appendix has important regulatory compliance information for the following products:zWireless Access Point AP200, models AP202 and AP209Please read this appendix first before installing and operating your product, and follow all instructions provided in the installation chapter. Periodic updates to this document will be posted at www.merunetworks.com.This appendix contains the following sections:zSafety SectionzFederal Communications Commission (FCC) Declaration of Conformity (DoC) & InstructionszList of Regulatory Compliance Certifications Summary by CountrySafety SectionUSA and CanadaEuropean UnionThe products listed in this appendix have been evaluated to, and comply with, the U.S. and Canadian (Bi National) Standard for Safety of Information Technology Equipment, including Electrical Business Equipment, CAN CSA C22.2, No. 60950-00 * UL 60950 3rd edition, and IEC60950:1999, the Standard for the Safety of Information Technology Equipment.Your product is intended to be installed, operated, serviced, and maintained by experienced personnel only. When using this device, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons.
48 Meru Access Point Installation GuideFederal Communications Commission (FCC) Declaration of Conformity (DoC) & Instructions Note the following:zThese products have been evaluated for indoor use only. ?zInstallation and use should be in strict accordance with the instructions described in this manual and any supporting documentation. zEnd use installation must conform to local regulations and codes. zThese products are powered by Power Over Ethernet (PoE) only, refer to the installation section for more information. zNo user serviceable parts inside. All repairs and service must be performed by trained personnel only. Do not open or disassemble your product. By opening or removing any covers, you may expose yourself to energized parts. Incorrect reassembly of these products can cause a malfunction and/or electric shock when the units are subsequently used.zDo not insert any objects of any shape or size inside the units. Objects may contact energized parts that could result in a risk of fire or personal injury.zDo not remove, alter, or cover the marking label provided. zTo avoid the risk of electric shock from lightning, do not operate your unit during an electrical storm. zWhen using external antenna, refer to the manufacturer’s installation documentation provided with the antenna system, and follow all instructions promptly. Installation must also conform to local regulations and codes.Federal Communications Commission (FCC) Declaration of Conformity (DoC) & Instructions Declaration of ConformityThis device is in conformance with Part 15 of the FCC Rules and Regulations for Information Technology Equipment. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Company InformationTrade Name MeruProduct Description Wireless Access Point AP200 Rev. 2Model Nos. AP202 & AP209Responsible Party Meru Networks Inc.
Federal Communications Commission (FCC) Declaration of Conformity (DoC) & Instructions Regulatory Information 49 We, the responsible party, Meru Networks Inc., declare that the above-listed product, Wireless Access Point AP200 Rev. 2 Model Nos. 202 & 209, was tested to conform to the applicable FCC Rules and regulations. The method of testing was in accordance to the most accurate measurement standards possible, and that all necessary steps have been enforced to assure that all production units of the same equipment will continue to comply with the Federal Communications Commission’s requirements.Issue Date: [TBD]Srinath Sarang VP, Product ManagementInstructionsWarnings This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, these products may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna.2. Increase the distance between the equipment and the receiver. 3. Connect the equipment to an AC outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Address 1309 S. Mary Ave. Sunnyvale, CA 94087Contact Person/Title Mohammad Sa-id Senior Regulatory Compliance Manager Phone - (408) 215-5300 Fax - (408) 215-5301EUT Certification SummaryEquipment Class Class BReport References [TBD] Issue Date [TBD] Tested by Bay Area Compliance LabCompany Information
50 Meru Access Point Installation GuideList of Regulatory Compliance Certifications Summary by Country In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may, for example, include the use of wireless equipment on board airplanes, or in any other environment where the risk of interference to other devices or services is perceived or identified as harmful. If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (such as airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment. CautionsExposure to radio frequency radiationTo comply with the FCC radio frequency exposure requirements, the following antenna installation and device operating configurations must be satisfied:zFor client devices using an integral antenna, the separation distance between the antenna(s) and any person’s body (including hands, wrists, feet and ankles) must be at least 2.5 cm (1 inch).zFor Base Stations and configurations using an approved external antenna, the separation distance between the antenna and any person’s body (including hands, wrists, feet and ankles) must be at least 20 cm (8 inch). zThe transmitter shall not be collocated with other transmitters or antennas.Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The correction of interference caused by unauthorized modification, substitution or attachment will be the responsibility of the user. The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to comply with these guidelines.List of Regulatory Compliance Certifications Summary by CountryEU In progress Japan In progressSafety approvals—US & Canada UL file no. E239453 USA/FCC ID RE7-AP200R2
List of Regulatory Compliance Certifications Summary by Country Regulatory Information 51
52 Meru Access Point Installation GuideList of Regulatory Compliance Certifications Summary by Country
Translated Safety Warnings 53 Appendix CTranslated Safety WarningsB-1This appendix provides translations of the safety warnings that appear in this publication. These translated warnings apply to other documents in which they appear in English. The following safety warnings appear in this appendix:zDipole Antenna Installation WarningzExplosive Device Proximity WarningzInstallation WarningzCircuit Breaker (15A) Warning
54 Meru Access Point Installation GuideDipole Antenna Installation Warning Dipole Antenna Installation WarningWarning! In order to comply with FCC radio frequency (RF) exposure limits, dipole antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.
Explosive Device Proximity Warning Translated Safety Warnings 55 Explosive Device Proximity WarningWarning! Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.
56 Meru Access Point Installation GuideInstallation Warning Installation WarningWarning! Read the installation instructions before you connect the system to its power source.
Circuit Breaker (15A) Warning Translated Safety Warnings 57 Circuit Breaker (15A) WarningWarning! This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).
58 Meru Access Point Installation GuideCircuit Breaker (15A) Warning
Channels 59 Appendix DChannelsB-1This appendix provides the access point radio channels supported by the world’s regulatory domains.This appendix contains the following section:zChannelsChannelsIEEE 802.11aThe channel identifiers, channel center frequencies, and regulatory domains of each IEEE 802.11a 20-MHz-wide channel are listed in Table 11. Note:All channel sets are restricted to indoor usage except the Americas, which allow for indoor and outdoor use on channels 52 through 64 in the United States. Table 11: IEEE 802.11a Channels Channel NumberFrequency in MHzRegulatory DomainsAmericas Japan34 5170 - X36 5180 X -38 5190 - X40 5200 X -42 5210 - X
60 Meru Access Point Installation GuideChannels IEEE 802.11b/gThe channel identifiers, channel center frequencies, and regulatory domains of each IEEE 802.11b/g 22-MHz-wide channel are listed in Table 12.44 5220 X -46 5230 - X48 5240 X -52 5260 X -56 5280 X -60 5300 X -64 5320 X -149 5745 X -153 5765 X -157 5785 X -161 5805 X -165 5825 X -Table 11: IEEE 802.11a Channels (Continued)Channel NumberFrequency in MHzRegulatory DomainsAmericas JapanNote:Mexico is included in the Americas regulatory domain; however, channels 1 through 8 are for indoor use only while channels 9 through 11 can be used indoors and outdoors. Users are responsible for ensuring that the channel set configuration complies with the regulatory standards of Mexico.Table 12: IEEE 802.11b/g Channels Channel NumberFrequency in MHzRegulatory DomainsAmericas EMEA Israel China Japan1 2412 X X - X X2 2417 X X - X X
Channels Channels 61 3 2422 X X X X X4 2427 X X X X X5 2432 X X X X X6 2437 X X X X X7 2442 X X X X X8 2447 X X X X X9 2452 X X X X X10 2457 X X - X X11 2462 X X - X X12 2467 - X - - X13 2472 - X - - X14 2484 - - - - X (for 802.11b only)Table 12: IEEE 802.11b/g Channels (Continued)Channel NumberFrequency in MHzRegulatory DomainsAmericas EMEA Israel China Japan
62 Meru Access Point Installation GuideChannels
63 MERU NETWORKS, INC.Limited Product WarrantyThis Limited Product Warranty applies to the original end-user customer of the Meru product which you purchased for your own use, and not for resale (“Product”), from Meru Networks, Inc. (“Meru”) or its authorized reseller (“Reseller”). Limited Warranties—One-year limited hardware warranty: Meru warrants to you that Meru hardware (other than Third Party Products as described below) will be free from defects in materials and workmanship for a one-year period after the date of delivery of the applicable product to you from Meru or its Reseller (the “Hardware Warranty Period”). If Meru receives written notice from you of such defects during the Hardware Warranty Period, Meru will, at its option, either repair or replace Meru hardware that Meru determines to be defective. Replacement products may be remanufactured units, and will be warranted for the remainder of the original Hardware Warranty Period, or if greater, for thirty days from delivery of such replacement. Should Meru be unable to repair or replace the Meru hardware, Meru (or its Reseller, as applicable) will refund to you the purchase price of the Product. —90-Day Limited Software Warranty: Meru warrants to you that, for a 90-day period after the date of delivery of the applicable product to you from Meru or its Reseller (the “Software Warranty Period”), when properly installed and used, (a) the media on which the Meru software is provided will be free from defects in materials or workmanship; and (b) the Meru software will substantially conform to the functional specifications in the applicable documentation. If Meru receives written notice from you of a breach of this warranty during the Software Warranty Period and is able to repro-duce the defect, Meru will, at its option, either repair or replace the defective Meru software. Should Meru be unable to repair or replace the Meru software, Meru (or its Reseller, as applicable) will refund to you the purchase price of the Product.ExclusionsThe warranty on the Product shall not apply to defects resulting from the following:—Alteration or modification of the Product in any way, including without limitation configuration with software or components other than those supplied by Meru or integration with parts other than those supplied by Meru.—Abuse, damage or otherwise being subjected to problems caused by negligence or misapplication (including without limitation improper or inadequate maintenance or calibration), relocation of the products (including without limitation damage caused by use of other than Meru shipping containers), or use of the products other than as specified in the appli-cable Meru product documentation (including without limitation incompatible operating environments and systems), or improper site preparation or maintenance.—Damage as a result of accidents, extreme power surge, extreme electromagnetic field, acts of nature or other causes beyond the control of Meru.—Use of the Product with software, interfacing, parts or supplies not supplied by Meru.The warranty on the Product does not apply if the Product is sold, or in the case of software, licensed, for free for evaluation or demonstration purposes.Meru expressly disclaims any warranty or obligation to support the Product for all operating environments – for example, as illustration and not limitation, Meru does not warrant or ensure interoperability of the Product with future telecommunication systems or other future software or hardware.You understand and acknowledge that the Products may generate, use or radiate radio frequency energy and may interfere with radio communications and/or radio and television receptions if is not used and/or installed in accordance with the documentation for such products. WHILE MERU USES COMMERCIALLY REASONABLE EFFORTS TO ENSURE COMPLIANCE OF THE PRODUCTS WITH APPLICABLE UNITED STATES FEDERAL COMMUNICATIONS
64 Meru Access Point Installation Guide COMMISSION AND PROTECT AGAINST HARMFUL INTERFERENCES, YOU ACKNOWLEDGE AND AGREE THAT INTERFERENCES WITH RADIO COMMUNICATIONS AND/OR RADIO AND TELEVISION RECEPTIONS MAY OCCUR AND THAT MERU WILL NOT BE LIABLE FOR ANY DAMAGES OR INCONVENIENCE BASED ON SUCH INTERFERENCES. Third Party Products - The above Limited Warranties are exclusive of products manufactured by third parties (“Third Party Products”). If such third party manufacturer provides a separate warranty with respect to the Third Party Product, Meru will include such warranty in the packaging of the Meru Product. Return proceduresTo obtain warranty service you must: (a) obtain a return materials authorization number (“RMA#”) from Meru by contacting support@merunetworks.com, and (b) deliver the Product, in accordance with the instructions provided by Meru, along with proof of purchase in the form of a copy of the bill of sale including the Product’s serial number, contact information, RMA# and detailed description of the defect, in either its original package or packaging providing the Product with a degree of protection equivalent to that of the original packaging, to Meru at the address below. You agree to obtain adequate insurance to cover loss or damage to the Product during shipment. If you obtain an RMA# and return the defective Product as described above, Meru will pay the cost of returning the Product to Meru. Otherwise, you agree to bear such cost, and prior to receipt by Meru, you assume risk of any loss or damage to the Product. Meru is responsible for the cost of return shipment to you if the Meru Product is defective.Returned products which are found by Meru to be not defective, returned out-of-warranty or otherwise ineligible for warranty service will be repaired or replaced at Meru’s standard charges and shipped back to you at your expense.At Meru’s sole option, Meru may perform repair service on the Product at your facility, and you agree to provide Meru with all reasonable access to such facility and the Product, as required by Meru. On-site repair service may be available and is governed by the specific terms of your purchase.All replaced parts, whether under warranty or not, are the property of Meru. Warranty limitationsTHE WARRANTIES SET FORTH ABOVE ARE EXCLUSIVE AND NO OTHER WARRANTY, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED BY MERU, TO THE MAXIMUM EXTENT PERMITTED BY LAW. THERE ARE NO OTHER WARRANTIES RESPECTING THE PRODUCT AND DOCUMENTATION AND SERVICES PROVIDED UNDER THIS AGREEMENT, INCLUDING WITHOUT LIMITATION ANY WARRANTY OF DESIGN, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (EVEN IF MERU HAS BEEN INFORMED OF SUCH PURPOSE), TITLE OR AGAINST INFRINGEMENT OF THIRD PARTY RIGHTS. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED UNDER APPLICABLE LAW, THEN SUCH IMPLIED WARRANTY SHALL BE LIMITED IN DURATION TO THE HARDWARE AND SOFTWARE WARRANTY PERIODS DESCRIBED ABOVE. NO AGENT OF MERU IS AUTHORIZED TO ALTER OR EXCEED THE WARRANTY OBLIGATIONS OF MERU.MERU SPECIFICALLY DOES NOT WARRANT THAT THE MERU SOFTWARE WILL BE ERROR FREE OR OPERATE WITHOUT INTERRUPTION.
65 THE REMEDIES IN THIS LIMITED PRODUCT WARRANTY ARE YOUR SOLE AND EXCLUSIVE REME-DIES, AND MERU’S SOLE AND EXCLUSIVE LIABILITY, FOR BREACH OF THE HARDWARE OR SOFT-WARE WARRANTY SET FORTH ABOVE.Limitations of LiabilityYou acknowledge and agree that the consideration which you paid to Meru does not include any consideration by Meru of the risk of consequential, indirect or incidental damages which may arise in connection with your use of, or inability to use, the Product. THUS, MERU AND ITS RESELLER WILL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION LOST PROFITS, LOST BUSINESS, LOST DATA, LOSS OF USE, OR COST OF COVER INCURRED BY YOU ARISING OUT OF OR RELATED TO YOUR PURCHASE OR USE OF, OR INABILITY TO USE, THIS PRODUCT OR THE SERVICES, UNDER ANY THEORY OF LIABILITY, WHETHER IN AN ACTION IN CONTRACT, STRICT LIABILITY, TORT (INCLUDING NEGLIGENCE) OR OTHER LEGAL OR EQUITABLE THEORY, EVEN IF MERU OR ITS RESELLER KNEW OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY EVENT, THE CUMULATIVE LIABILITY OF MERU OR ITS RESELLER FOR ALL CLAIMS WHATSOEVER RELATED TO THE PRODUCT OR THE SERVICE WILL NOT EXCEED THE PRICE YOU PAID FOR THE PRODUCT OR SERVICES GIVING RISE TO SUCH CLAIMS.THE LIMITATIONS SET FORTH HEREIN ARE INTENDED TO LIMIT THE LIABILITY OF MERU AND ITS RESELLERS AND SHALL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY.The jurisdiction applicable to you may not allow the limitations of liability or damages set forth above, in which case such limitation shall only apply to you to the extent permitted in such jurisdiction.Additional InformationThis Limited Product Warranty shall be governed by and construed in accordance with the laws of the State of California, U.S.A., exclusive of its conflict of laws principles. The U.N. Convention on Contracts for the International Sale of Goods shall not apply.This Limited Product Warranty is the entire and exclusive agreement between you and Meru with respect to its subject matter, and any modification or waiver of any provision of this statement is not effective unless expressly set forth in writing by an authorized representative of Meru.All inquiries or claims made under this Limited Product Warranty must be sent to Meru at the following address:Meru Networks Inc.,1309 South Mary Avenue, Sunnyvale, CA 94087, USATel: 408-215-5300Fax: 408-215-5301Email: support@merunetworks.com
66 Meru Access Point Installation Guide
Meru Networks, Inc.1309 South Mary AvenueSunnyvale, CA 94087408-215-5300www.merunetworks.com

Navigation menu