Microair Avionics T2000UAV-L UAV AIRCRAFT TRANSPONDER User Manual
Microair Avionics PTY LTD UAV AIRCRAFT TRANSPONDER Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1415826 |
| Application ID | eq3Cuh6c4k+CoR83ZmEKpA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 137.96kB (1724532 bits) |
| Date Submitted | 2011-02-11 00:00:00 |
| Date Available | 2011-02-14 00:00:00 |
| Creation Date | 2010-08-12 17:31:22 |
| Producing Software | Acrobat Distiller 9.3.3 (Windows) |
| Document Lastmod | 2010-08-12 17:31:22 |
| Document Title | Microsoft Word - T2000UAV-L Installation and User Manual 01R1.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | ianm |
Microair Avionics Pty Ltd Airport Drive Bundaberg Queensland 4670 Australia Tel: +61 7 41 553048 Fax: +61 7 41 553049 e-mail: sales@microair.com.au Microair Avionics T2000UAV-L Install and User Manual About This Document This supplement describes the installation option, and software controls for the T2000UAV-L transponder, operating with software revision T2000UAV-L_01R6.5. Microair reserves the right to amend this supplement as required, to reflect any enhancements or upgrades to the T2000 transponder series. © Microair Avionics Pty Ltd REVISION STATUS Revision 01R1 Date 28/07/09 Change Initial release The T2000UAV-L Transponder is not a TSO’d product. T2000UAV-L Installation and User Manual 01R1.doc Page 2 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual TABLE OF CONTENTS 1.0 INTRODUCTION 2.0 T2000UAV-L DESCRIPTION 2.1 3.0 3.1 3.2 3.3 3.4 3.4.1 3.4.2 3.4.3 3.4.4 3.4.5 3.4.6 3.4.7 3.4.8 3.4.9 3.4.10 T2000UAV-L ANTENNA OPTIONS SOFTWARE CONTROL MICROAIR UAV TERMINAL SOFTWARE THE UAV COMMAND STRUCTURE DATA SPEED SERIAL DATA COMMAND SET Standby (s=t) Mode 3A (s=a) Mode C (s=c) Ident (i=s) Altitude (a=?) Altitude Source (d=?) Encoder Power (e=?) Voltage (v=?) Reply Annunciator (r=y) Ping Function (p=?) 10 10 10 10 4.0 T2000UAV-L TIE DOWN STRAP 11 5.0 MODE C ENCODER 11 6.0 ANTENNA 12 7.0 COAXIAL CABLE 12 8.0 WIRING 13 8.1 8.2 8.3 8.4 8.5 CABLING POWER ON/OFF SUPPRESSION IN / OUT EXTERNAL STANDBY EXTERNAL IDENT 13 14 14 14 14 9.0 TECHNICAL DRAWINGS 15 10.0 WIRING DIAGRAMS 17 11.0 PIN ASSIGNMENTS 22 12.0 SPECIFICATIONS 23 13.0 LIMITED WARRANTY 24 T2000UAV-L Installation and User Manual 01R1.doc Page 3 of 24 28th July 2009 Microair Avionics 1.0 T2000UAV-L Install and User Manual INTRODUCTION The T2000UAV-L is a special version of the T2000 Transponder, designed for operation in unmanned aircraft. This product is not TSO’d due to the OEM nature of the management software. The system consisting of the T2000UAV-L, and the OEM’s management software control should collectively be submitted for compliance to TSO C74c, as part of the OEM’s type certificate. The T2000UAV-L is based upon the certified T2000SFL transponder, and is known to comply with the following: Environmental: Software: Transponder Function: RTCA/DO-160D RTCA/DO-178B RTCA/DO-144A Transmitter Operation FCC Approval T2000UAV-L Installation and User Manual 01R1.doc Page 4 of 24 28th July 2009 Microair Avionics 2.0 T2000UAV-L Install and User Manual T2000UAV-L DESCRIPTION The UAV-L version of the T2000SFL has no display. The chassis has been truncated by having the display housing milled off. The front face is plated off and sealed. A command set allows the UAV’s flight management system to have full functional control over the transponder. The RS-232 interface is accessed from the DB-25 connector on the rear face of the chassis. The T2000UAV-L requires a standard Gillham code altitude encoder, to supply altitude data over a 10 line parallel interface. The T2000UAV-L features remote switching options, available from the rear DB-25 connector for remote standby and remote ident functions. 2.1 T2000UAV-L ANTENNA OPTIONS The T2000UAV-L can be supplied with a standard BNC connector located on the rear face of the chassis, adjacent to the DB-25. Part Number: T2000UAV-L_01R1 Order Number: T2000UAV-L_MA1358_01R1-0 The T2000UAV-L can be supplied with a standard TNC connector located on the rear face of the chassis, adjacent to the DB-25. Part Number: T2000UAV-L_01R1 Order Number: T2000UAV-L_MA1359_01R1-0 T2000UAV-L Installation and User Manual 01R1.doc Page 5 of 24 28th July 2009 Microair Avionics 3.0 T2000UAV-L Install and User Manual SOFTWARE CONTROL The T2000UAV-L can be controlled by issuing of commands in the form of ASCII characters, sent and received over an RS232 interface. The command set can be used to either poll the transponder of the status of a parameter, or to command a function to a particular setting. 3.1 MICROAIR UAV TERMINAL SOFTWARE The T2000UAV-L is supplied with UAV Control software to which it is capable of issuing all commands, and polling for all parameters. The terminal software is a simple EXE file, and is compatible with windows 98 through to windows XP operating systems. The terminal software is capable of issuing all of the commands, to either poll for any of the parameters, or to set any of the parameters to discrete values. T2000UAV-L Installation and User Manual 01R1.doc Page 6 of 24 28th July 2009 Microair Avionics 3.2 T2000UAV-L Install and User Manual THE UAV COMMAND STRUCTURE The T2000UAV-L is controlled by a series of simple commands. The T2000UAV-L can be commanded to set a code, and to operate in a particular mode. Once the code is set, and the operating mode decided, the T2000UAV-L will operate until another command is received. The status the T2000UAV-L’s various operating parameters can be queried. A query command returns a value for that particular parameter. The operator can address the T2000UAV with a command from the command set, via an RS232 interface. The command requires the correct syntax, to be valid. The command string will consist of STXx=ETX Where STX ETX 3.3 is the non-printable ASCII character (02) is the non-printable ASCII character (03) is a valid command maybe either ? or a string of ASCII characters, if the is a ?, this will evoke a response for that command DATA SPEED The RS232 interface for the T2000UAV-L has a data rate of: 9600,N,8,1,P where 9600 = 8= 1= P= baud rate of 9600 8 data bits 1 stop bit with XON / XOFF Refer to section 10.0 for wiring details and pin assignments. T2000UAV-L Installation and User Manual 01R1.doc Page 7 of 24 28th July 2009 Microair Avionics 3.4 T2000UAV-L Install and User Manual SERIAL DATA COMMAND SET CMD Action Write String Response Altitude (Read/Write) a=? a=xxxxx where xxxxx=altitude in feet a=#$*& where #$*&=altitude in feet a= eg 1234F a=xxxxx (writes altitude data in feet to T2000UAV) a=? (invalid altitude data) Assigned Code (Read/Write) c=2212 (set code to 2212) c=? (ask for assigned code) c=2212 (code write successful) c= Assign altitude source (Read/Write) d=g (set altitude source = Gillham) d=s (set altitude source = Serial) d=? d=g (altitude source = Gillham) d=s (altitude source = Serial) d= Encoder power control (Read/Write) e=o (set encoder power always ON) e=c (set encoder power mode C only) e=? e=o (Encoder power on in both mode A and C) e=c (Encoder power on in mode C only) e= Ident (Read/Write) i=s (Squawk Ident) i=? (ask for current ident status) i=1 (1 = Ident active, 0 = Ident inactive) i= Ping Function p=? p=y (yes – ping cycle was successful) p=n (no – ping was not successful) Reply Annunciator r=y r=n r=? * is sent if a reply was made in the last 3.6 seconds no annunciation character is sent r= Operational Status (Read/Write) s=t (command standby mode) s=a (command Mode A operation) s=c (command Mode C operation) s=? (ask for current operational mode) s=t (command successful, mode = standby) s=a (command successful, mode = Mode 3A) s=c (command successful, mode = Mode C) s= Bus Voltage (Read/Write) v=1 (set bus voltage to 14V) v=2 (set bus voltage to 28V) v=13.6 (write successful, current voltage returned) v=24.8 (write successful, current voltage returned) Software Revision z=? z= eg T2000U xx-x.x.x T2000UAV-L Installation and User Manual 01R1.doc Page 8 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual 3.4.1 STANDBY (S=T) To bring the T2000UAV-L to the standby condition, the “s” parameter is set to value “t”. Then the transponder can then be powered down. When the T2000UAV-L is restarted, it will return in standby The transponder should be commanded to the standby condition, when the vehicle is on the ground. The transponder is typically set to mode 3A or mode 3A/C operation once airborne. 3.4.2 MODE 3A (S=A) The T2000UAV-L transponder will respond to all mode A interrogations with the identity code set by the “c” parameter. The transponder will also reply to all mode C interrogations with just the framing pulse (no altitude data). This ensures visibility to TCAS operators, while the transponder is operating in mode A. 3.4.3 MODE C (S=C) The T2000UAV-L will respond to all mode A interrogations with the identity code set by the “c” parameter, and all mode C interrogations with the encoder’s altitude data, as defined by the “a” parameter. The transponder will reply to both SSR and TCAS interrogations. 3.4.4 IDENT (I=S) The ident function is performed at the request of ATC to “squawk ident”. To initiate the ident function the “i” parameter is set to s. The T2000UAV-L will switch to ident mode, which will add an additional data bit to the outgoing replies. The additional data bit makes the transponder return on the ATC display flash to assist the controller with identification. The transponder will remain in ident mode for 18 seconds, and then return to the previous mode of operation. 3.4.5 ALTITUDE (A=?) The T2000UAV-L will reply with the current mode C value. If the T2000UAV-L is configured to operate with an altitude encoder the T2000UAV-L will reply with the current barometric altitude from the encoder. If the T2000UAV-L is configured to operate with a serial altitude data source, the T2000UAV-L will reply with the last received altitude data value. 3.4.6 ALTITUDE SOURCE (D=?) The T2000UAV-L can accept altitude data for the mode C response either from a Gillham (d=g for 10 line parallel) source or from a serial (d=s for RS232) source. When d=g is selected the T2000UAV-L will look to the 10 line Gillham input for data from an altitude encoder. When d=s is selected the T2000UAV-L will look for altitude data to be passed via the “a” command on the RS232 serial data link. The altitude data source shall send the a= where the altitude value is between -1000 and 62000 feet, in increments of 100 feet. The altitude data source should issue this data report to the T2000UAV-L no slower than 1Hz. Where the altitude data cannot be detected from the assigned source or the data cannot be encoded, no altitude data will be outputted. The mode C response will be framing pulses only. The T2000UAV-L will question the altitude data with a=?, via the RS232 serial interface. T2000UAV-L Installation and User Manual 01R1.doc Page 9 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual 3.4.7 ENCODER POWER (E=?) When using an altitude encoder, it may be desirable to only have it powered up when the transponder is operating in mode C. This may save power, as most encoders will typically draw 125 to 150mA when operating. The operator should allow up to 7 minutes for the encoder to “warm up” before valid altitude data is outputted from the encoder. 3.4.8 VOLTAGE (V=?) The T2000UAV-L will report the current vehicle bus voltage by polling the “v” parameter. To use this function operator must first set the reference bus voltage by setting v=1 for 14V operation, or v=2 for 28V operation. 3.4.9 REPLY ANNUNCIATOR (R=Y) A conventional transponder normally has an annunciator of some type (typically a flashing LED) to indicate the rate of reply to SSR interrogations. This indication represents whether the transponder has made a reply to a “sweep”. The rotational speed of the radar is 100 deg/sec, hence the Annunciator should flash every 3.6 seconds. The equivalent function for the T2000UAV-L is the “r” command which activates the reply annunciator. When activated (r=y), the T2000UAV-L will send a single * character, if there was a reply made in the preceding 3.6 seconds. When not activated (r=n), no character is sent. The operator can query the status of the reply annunciator function (r=?), and the T2000UAV-L will reply with the current function state. 3.4.10 PING FUNCTION (P=?) The ping function is a self test of the RF sections of the transponder, without the need for a transponder test set. The T2000UAV-L will respond to the “ping” command (p=?) by emitting a narrow (invalid) pulse from the transmitter, and detecting the same pulse back through the receiver. If the T2000UAV-L is able to complete the transmission cycle, p=y is returned to the operator. If the T2000UAV-L is not able to complete the transmission cycle, p=n is returned to the operator. The ping function will only operate if the transponder is in mode a or c. The ping function will not operate while the transponder is in standby mode. T2000UAV-L Installation and User Manual 01R1.doc Page 10 of 24 28th July 2009 Microair Avionics 4.0 T2000UAV-L Install and User Manual T2000UAV-L TIE DOWN STRAP Microair recommends a simple tie down strap, to hold the transponder in place. Drawing MA1156 shows the layout and use of a simple example. Never use the case screws as part of the mounting system for the transponder. Always locate the strap over the chassis at a point which remains clear of the filter lock nuts. Part Number: 5.0 T2000UAV-L_MA1156_01R1-1 MODE C ENCODER Mount the mode C blind encoder as per the manufacturer’s installation instructions. All wiring can be run back to the T2000UAV-L for connection (refer wiring diagram). The power for the encoder is supplied from the T2000UAV-L. This power is switched when the T2000UAV-L is turned on. IMPORTANT NOTE Most encoder manufacturers advise of a warm up period for their product before altitude data is supplied. The period can typically be up to 10 minutes. Where the OEM intends to use their own barometric altitude data source, it should comply to TSO C88a standard, to be sure of compatibility with the T2000UAV-L. Although it is unlikely that the encoder source in a UAV installation will require switched power from the T2000UAV-L, it is recommended that the ground be wired with the data lines in all cases. This will ensure correct signal operation of the Gillham code. T2000UAV-L Installation and User Manual 01R1.doc Page 11 of 24 28th July 2009 Microair Avionics 6.0 T2000UAV-L Install and User Manual ANTENNA Mount the transponder antenna as per the manufacturer’s installation instructions. Try and keep the cable runs as short as possible. In a composite airframe a suitable ground plane will be required. Avoid mounting the antenna inside a fuselage that is all metal or carbon fibre. For fiberglass fuselages the antenna may be mounted internally, but must still point downwards and have an adequate ground plane. Alternatively an approved dipole strip antenna may be used. The dipole strip must be installed in accordance with the manufacturer’s instructions. To avoid possible interference the antenna must be mounted a minimum of 200mm (8 inches) from the T2000UAV-L main unit. The transponder antenna should be mounted 2metres (78 inches) from the DME antenna, 1.5 metres (58 inches) from the ADF sense antenna, and 1metre (39 inches) from TCAS antennas. 7.0 COAXIAL CABLE The T2000UAV-L allows for 1.5dB cable loss from the unit to the antenna. The installer should consider carefully what type of coaxial cable is to be used, so that this loss limit is not exceeded. The cable should be terminated with silver plated BNC connectors where possible. Microair recommends the following: Cable RG58/C/U (Mil Spec) RG213/A/U (Mil Spec) RG223/U (Mil Spec) RG400 (Mil Spec) Belden 8262 URM-43 Bending Radius 50mm (2”) 125mm (5”) 100mm (4”) 50mm (2”) 50mm (2”) 50mm (2”) Loss @ 1Ghz dB/m 0.76dB/m 0.21dB/ft 0.26dB/m 0.08dB/ft 0.47dB/m 0.14dB/ft 0.60dB/m 0.18dB/ft 0.68dB/m 0.21dB/ft 0.47dB/m 0.14dB/ft Max Length 2.0m 7ft 5.75m 19ft 3.2m 10ft 2.5m 8ft 2.2m 7ft 3.2m 10ft TX Power RX Sensitivity 142W -70dBm 142W -70dBm 142W -70dBm 142W -70dBm 142W -70dBm 142W -70dBm The loss figures in this table are a guideline only. When installed the power output at the antenna shall be greater than 125W and receiver sensitivity shall be better than -68dBm, to be compliant with RTCA/DO-144A. IMPORTANT NOTE Do not exceed the minimum bending radius. Tight bends will introduce losses in the cable, which may affect the performance of the transponder. When fixing the coax cable in the airframe, do not “strangle” the cable with tight cable ties. This can distort or damage the coax screen. T2000UAV-L Installation and User Manual 01R1.doc Page 12 of 24 28th July 2009 Microair Avionics 8.0 T2000UAV-L Install and User Manual WIRING The T2000UAV-L Transponder receives primary power (14V or 28V dc) from the aircraft’s power source. Power connections, voltage, and circuit breaker requirements are shown on the wiring diagram. The length of the power supply wires to parallel pins should be approximately the same length, so that the best distribution of current can be effected. Microair recommends that the encoder be installed and wired in accordance with the manufacturer’s installation instructions. It is very important to secure all D series plugs via their security screws before operation. Aircraft vibration may disconnect a D series plug if it not secured. Where possible, the antenna coaxial cable should be run separately to all other wiring on the aircraft from the transponder. 8.1 CABLING Microair recommends that wiring for all of the T2000UAV-L’s functions and connections be run at the time of installation, even though they may not be required at this stage. Adding additional wiring to the loom at a later stage may be very difficult. All wiring should be installed in accordance with FAA AC43.13-1A Chapter 11 or equivalent. Microair recommends the following cable types for connection of the T2000UAV-L: Power Input 18 AWG TEFZEL 22759/16-16 Red and Black Wire External Connections 22 AWG TEFZEL 22759/16-22 22 AWG TEFZEL 27500-22TG1T14 Wire or Single core shielded Encoder Power 22 AWG TEFZEL 22759/16-22 Red and Black Wire Encoder Data 22 AWG TEFZEL 22759/16-22 White Wire When terminating the DB plugs for connection to the T2000UAV-L, ensure that the wires are securely soldered to the pins, and that each wire is separately insulated with heatshrink tubing. “Tinned” wire Soldered with heatshrink Locking bolts tightened The DB-25 plug is secured to the T2000UAV-L with machine screws or thumb screws. The DB-15 should also be secured to the encoder, either with screws, or mechanical sliding lock (if fitted to some types of encoder). If your encoder is fitted with a slide locking mechanism, the encoder manufacturer’s plug should be used, to ensure correct locking action. T2000UAV-L Installation and User Manual 01R1.doc Page 13 of 24 28th July 2009 Microair Avionics 8.2 T2000UAV-L Install and User Manual POWER ON/OFF The T2000UAV-L has no ON/OFF control function. The unit is on from the moment power is applied to the unit. There is no software OFF command. When power is removed from the T2000UAV-L, it will not respond to any software command. When the T2000UAV-L is turned on, it is always in standby mode. The mode A code will default to the last mode A code used. IMPORTANT NOTE Always bring the T2000UAV-L to standby before turning off the power. If the transponder is powered off while it is in the process of transmitting, damage may occur to the internal power supply and/or the transmitter. Damage of this type is not covered by the warranty. No mode C code will be outputted until the T2000UAV-L is supplied with altitude data (either serial or Gillham) which can be encoded by the transponder. 8.3 SUPPRESSION IN / OUT The suppression IN line is wired to other avionics such as DME, to “suppress” the transponder’s transmissions, at times critical to the other equipment’s operation. The suppression OUT line does the reverse of the IN line. It is wired to other avionic equipment to allow the T2000UAV-L to “suppress” their transmissions at times critical to the T2000UAV-L’s operation. Seek the advice of a qualified Avionics Technician before attempting to wire out these functions. If certified equipment is modified to operate in conjunction with the T2000UAV-L installation, then the installation of that equipment must be re-inspected and re-approved before operation. 8.4 EXTERNAL STANDBY The external standby can be wired to a remote switch. When the line is taken to ground the T2000UAV-L will return to standby mode, and stay there regardless of the value for “s” parameter. The “s” parameter cannot be queried while the external standby line is grounded. Once the external standby line has been “released” from ground, the T2000UAV-L will revert to the last “s” parameter setting. 8.5 EXTERNAL IDENT Future development. T2000UAV-L Installation and User Manual 01R1.doc Page 14 of 24 28th July 2009 Microair Avionics 9.0 T2000UAV-L Install and User Manual TECHNICAL DRAWINGS T2000UAV-L Installation and User Manual 01R1.doc Page 15 of 24 28th July 2009 Microair Avionics T2000UAV-L Installation and User Manual 01R1.doc T2000UAV-L Page 16 of 24 Install and User Manual 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual 10.0 WIRING DIAGRAMS T2000UAV-L with EC2002 Altitude Encoder T2000UAV-L with AK-350 Altitude Encoder T2000UAV-L with A-30 Altitude Encoder T2000UAV-L with serial altitude data interface T2000UAV-L Installation and User Manual 01R1.doc Page 17 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH EC2002 ALTITUDE ENCODER T2000UAV-L Installation and User Manual 01R1.doc Page 18 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH AK-350 ALTITUDE ENCODER T2000UAV-L Installation and User Manual 01R1.doc Page 19 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH A-30 ALTITUDE ENCODER T2000UAV-L Installation and User Manual 01R1.doc Page 20 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH SERIAL ALTITUDE DTA INPUT T2000UAV-L Installation and User Manual 01R1.doc Page 21 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual 11.0 PIN ASSIGNMENTS The DB plugs for use with the T2000 series Transponders, require the following pin assignments. PIN 1 NOT WIRED PIN 2 SWITCHED MODE C ENCODER POWER OUTPUT PIN 3 GROUND PIN 4 RS232 RX PIN 5 RS232 TX PIN 6 NOT WIRED PIN 7 NOT WIRED PIN 8 SUPPRESSION IN PIN 9 GILLHAM ALTITUDE A1 PIN 10 GILLHAM ALTITUDE A2 PIN 11 GILLHAM ALTITUDE A4 PIN 12 GILLHAM ALTITUDE B1 PIN 13 GILLHAM ALTITUDE B2 PIN 14 SUPPRESSION OUT PIN 15 EXTERNAL STANDBY IN PIN 16 EXTERNAL IDENT PIN 17 GILLHAM ALTITUDE B4 PIN 18 GILLHAM ALTITUDE C1 PIN 19 GILLHAM ALTITUDE C2 PIN 20 GILLHAM ALTITUDE C4 PIN 21 GILLHAM ALTITUDE D4 PIN 22 POWER GROUND PIN 23 POWER GROUND PIN 24 POWER 14 OR 28 VOLTS DC (10-33 VOLTS) PIN 25 POWER 14 OR 28 VOLTS DC (10-33 VOLTS) T2000UAV-L Installation and User Manual 01R1.doc Page 22 of 24 28th July 2009 Microair Avionics T2000UAV-L Install and User Manual 12.0 SPECIFICATIONS RTCA Compliance DO-144A DO-160D DO-178B Level C Transmitter 1090MHz +/-0.2MHz 200W Pulse Output 80nS Rise Time 120nS Fall Time Receiver +10 to –72dBm Dynamic Range 1030MHz Centre Frequency +/-5MHz Pass band @ -3dB Input Power 10-33Vdc 100-150mA @ 28V 150-200mA @ 14V Operational Modes Standby Mode 3A (4096 codes) Mode 3A/C Temperature -20° C to +55°C Dimensions Width 61mm Height 61mm Length 134mm Weight 454 g (16 oz) Specifications are subject to change without notice. T2000UAV-L Installation and User Manual 01R1.doc Page 23 of 24 28th July 2009 13.0 LIMITED WARRANTY T2000UAV-L Installation and User Manual 01R1.doc Page 24 of 24 24th April, 2009
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : ianm Create Date : 2010:08:12 17:31:22+10:00 Modify Date : 2010:08:12 17:31:22+10:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : Microsoft Word - T2000UAV-L Installation and User Manual 01R1.doc Creator : ianm Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.3.3 (Windows) Document ID : uuid:3f8fba90-19d0-43b3-aec7-3212c70b80a5 Instance ID : uuid:e8175b65-04b2-47eb-b2e2-dcbff99a0ac6 Page Count : 24EXIF Metadata provided by EXIF.tools