Midea Smart Technology 0003 Zigbee module User Manual UserManual

Download:
Mirror Download [FCC.gov]
Document ID	3224978
Application ID	VSBzF3EqqtmRqkYshNdrYw==
Document Description	UserManual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.77kB (984632 bits)
Date Submitted	2016-12-12 00:00:00
Date Available	2016-12-12 00:00:00
Creation Date	2016-11-28 15:47:21
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2016-11-29 16:33:14
Document Title	UserManual
Document Creator	Microsoft® Office Word 2007
Document Author:	Huanghai

MM875033-11
zigbee Module
Datasheet
Revision
Date
Description
1.0
2016-11-11
initial release
Author
contents
1.
Introduction ........................................................................................................................... 3
1.1
1.1 Module System Block Diagram ...................................................................... 4
1.2
Module technical specifications ......................................................................... 5
Structure specification ........................................................................................................ 5
2.1 Module structure size .................................................................................................... 5
2.2 Hardware interface definition.................................................................................... 7
Wireless Specification ......................................................................................................... 8
1. Introduction
MM875033-11 is a low-power Zigbee module for the Internet of
Things,making the terminal more reliable, convenient and easy to
use.
The MM875033-11
module contains a NXP JN5169 single-chip
solution. the chip in software and hardware are used in low-power
technology, the purpose is to lower the power consumption of the
entire board, the product more competitive. The module makes up with
rf circuit, antenna, zigebee SOC, power supply, crystals and other
auxiliary circuit。At present, the module provides a complete serial
interface functions and equipment to communicate, so you can
through the serial port and mobile client to connect the cloud and
equipment.

2.4 GHz IEEE802.15.4 compliant

On-board antenna

2.0 V to 3.6 V battery operation

Power saving technology with low consumption

RX current 14.7 mA, in low power receive mode 13 mA

Configurable transmit power

Deep sleep current 140 nA (wake-up from IO)

Compensation for temperature drift of crystal oscillator frequency

The JN5169 features 512 kB embedded Flash, 32 kB RAM and 4 kB
EEPROM memoryand radio outputs up to 10 dBm.
1.1 1.1 Module System Block Diagram
As shown in Figure 1, The MM875033-11 module contains a NXP
JN5169 single-chip solution, the chip highly integrated CPU, PMU, RAM,
Transceiver, LNA, PA, memmory, and other major parts, thus greatly
reducing the machine power, Amplitude reduces the layout area. The
module uses the internal antenna design in PCB, both for customers to
reduce the cost of the antenna, but also eliminates the need to
consider the antenna assembly space.
figure 1. Module System Block Diagram
1.2 Module technical specifications
Main chip
JN5169
Working frequency
2.40~2.485GHz
Supported standard
IEEE802.15.4
Modulation
O-QPSK MODEM
communication interface
UART
PCB layer structure
4 Layer
PCB size
22mm(L)x17mm(W)x2.0mm(H)
Antenna
PCB internal antennas
Operation temperature
0℃~+85℃
Storage temperature
-40℃~+125℃
Hardware version number
Msmart-Zigbee(JN5169)-A[V1.1]
2 Structure specification
2.1 Module structure size
The size of the module as shown above, length 22mm, width 17mm, thickness
2.0mm (error +/- 0.2mm)
2.2 Hardware interface definition
ADC1
ADC INPUT 1
15
GND
Ground
SPICLK
SPI BUS master clock out
16
VCC
Supply Input Pin
SPIMISO
SPI BUS master in,slave out
17
VCC
Supply Input Pin
18
GND
Ground
input
SPIMOSI
SPI BUS master out,slave in
output
SSZ
SPI BUS master select output 0
19
DIO11
GPIO
DIO0
GPIO&ADC INPUT 3
20
DIO12
GPIO
DIO1
GPIO& ADC INPUT 4
21
DIO13
GPIO
DIO2
GPIO& ADC INPUT 5
22
RESETN
Reset pin，Active Low
DIO3
GPIO& ADC INPUT 6
23
DIO14
UART1-TX&I2C-SCL
10
DIO4
GPIO
24
DIO15
UART1-RX&I2C-SDA
11
DIO5
GPIO
25
DIO16
I2C-SCL &GPIO
12
DIO6
UART0-TX
26
DIO17
I2C-SDA &GPIO
13
DIO7
UART0-RX
27
ADC2
ADC INPUT 2
14
DIO8
GPIO
3 Wireless Specification
reference
section
limit
TX Maximum Power
ETSI EN 300 328 4.3.2.1
20dBm
TX Spurious 30Mhz-1Ghz
ETSI EN 300 328 4.3.2.8
-36 or -54dbm(depends on
frequency)(100khz BW)
ETSI EN 300 328 4.3.2.8
-30 dBm
802.15.4
802.15.4
802.15.4
No reference
ETSI EN 300 328
ETSI EN 300 328
802.15.4
10.3.8
10.3.9
10.3.10
35%
+/-40 ppm
-3dBm
4.3.2.9.2
4.3.2.9.2
10.3.4
-57dBm(100 Khz)
-47 dBm(1 Mhz)
-85dBm
802.15.4
10.3.5
0dB
802.15.4
10.3.5
30dB
802.15.4_2011
10.3.11
-20dBm
Transmission
Reception
ECM
TX Frequency Tolerance
min of max power
phase noise(unspread)
RX spurious 30Mhz - 1GHz
RX spurious 1G - 12.5GHz
RX sensitivity
Interference rejection
N+/-1(adjacent)
Interference rejection
N+/-2(alternate)
RX Max input
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, p
ursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection again
st harmful interference in a residential installation. This equipment generates and can radiate radi
o frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to rad
io or television reception, which can be determined by turning the equipment off and on, the use
r is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is con
nected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditio
ns: (1) This device may not cause harmful interference, and (2) This device must accept any interf
erence received, including interference that may cause undesired operation.
"Contains Transmitter Module FCC ID:2AIRV0003" or "Contains FCC ID:2AIRV0003" must be used.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Warning                         : Invalid secondary xref table
Language                        : zh-CN
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Huanghai
Create Date                     : 2016:11:28 15:47:21Z
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2016:11:29 16:33:14+08:00
Metadata Date                   : 2016:11:29 16:33:14+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:b866517e-da19-4cbc-826d-e0e201b1932b
Instance ID                     : uuid:10642f8a-41cb-41b1-8e13-9144d954ad77
Page Count                      : 9
Author                          : Huanghai

EXIF Metadata provided by EXIF.tools