field. 4.4.2.2.1 Attach Decode No. "OFF" format Pressing the PTT lever first automatically selects the DTMF encoding format and allows direct entry of DTMF tones. Hold the PTT lever on the microphone depressed while pressing the required DTMF tones. The tones will be transmitted as the keys are being pressed. 4.4.2.2.2 Attach Decode No. "ON" format Attach Decode No. "ON" automatically encodes the users DTMF decode number after the encode number. This can be used for ANI purposes. Enter the required DTMF tones (up to sixteen tones except "B" tone) and then transmit the total tone sequence (including the users decode number) by pressing the [#] key. All tones will be transmitted in one continuous sequence after pressing the [#] key. Pressing the [ ] key will delete the last entered number. Always confirm that the LCD is clear before proceeding as it may take up to 5 seconds for the tones to be sent. e.g. Assume that your decode number is 12345, and that you wish to encode number 12346. You will input 12346, and then press the [#] key. The KG510 will encode 12346B12345. The called radio will display 12345 in their LCD indicating the calling party's number is 12345. NOTE: The "B" tone is used as the delimiter in this encoding format and therefore CANNOT be used as a DTMF tone. Pressing the [SHIFT] key and then the [#] will encode ONLY the encode number (and not the decode number). 133838 Page #12 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.4.2.3 Redialling with DTMF If during the programming of the KG510, the field has been set to "OFF", the redialling function operates as follows: Press [SHIFT], then press [#] and the KG510 will redial the last encoded DTMF number. If during the programming of the KG510, the field has been set to "ON", the redialling function operates as follows: Press [#] and the KG510 will redial the last encoded DTMF number with the KG510's programmed decode number. Press [SHIFT], and then press [#] and the KG510 will redial the last encoded DTMF number without the KG510's programmed decode number. 4.4.2.4 Restoring the last DTMF number to the LCD Display It is possible to restore the last encoded DTMF number to the LCD display, provided the field has been set to "ON" during the programming of the KG510 transceiver. Confirm that the LCD is NOT displaying any DTMF numbers, then press [✶] and the last encoded DTMF number will be displayed in the LCD display. It is possible to edit this number at this time by pressing the [✶] key (which will erase the last number) or by pressing the required keys to add additional numbers. 4.4.2.5 Encoding DTMF numbers with the 5-Tone system enabled It is possible to enter DTMF numbers even with the 5-Tone system enabled. This function must be enabled during the programming of the KG510 by setting the field in the <5Tone Encode Menu> to "ENABLE". To enter a DTMF number (with 5-Tone signalling enabled), the user must press the PTT lever while entering the first DTMF number. Second and subsequent numbers do NOT require the PTT lever to be pressed provided all numbers are entered within a few seconds (before the display reverts to 5-Tone mode and displays "5TON" in the LCD display). 4.4.3 Single Tone Encoding The KG510 has the ability to encode one of six single tone frequencies for 1, 2, 3, or 4 seconds. This function is enabled during programming of the KG510 by selecting the field in the and setting the encode period. Press the [SHIFT] and the [4] keys to put the KG510 into Single Tone Encoding mode. "S1" and the tone frequency ("xxxxHz") will be displayed in the tone area of the LCD display for about 4 seconds until the KG510 reverts back to the normal signalling mode. While the KG510 is in Single Tone Encoding mode, it is possible to advance to the next tone frequency by pressing the [A] key, or to return to the previous tone by pressing the [B] key. Pressing the [#] key will encode the displayed tone (for the programmed time period) and automatically exits the Single Tone Encoding mode and returns the KG510 to the normal signalling mode. 133838 Page #13 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.4.4 KILL Signalling The KG510 has the ability to transmit a specially coded signalling sequence that will disable ("KILL") another radio. This feature is particularly useful when transceivers become misplaced, are stolen, if they are used in an incorrect manner, or if they are used for the wrong purposes. To prevent accidental or mischievous "KILLING" of radios, several security features are in place. Firstly, the KG510 must have this function enabled during programming. Secondly, the user must know the required password and enter it correctly into the KG510, and, Thirdly, the user must know the required "KILL" number (of the radio to be "KILLED", and enter it correctly into the KG510. The "KILL" password has four numerical digits. [0] to [9]. With 5-Tone signalling systems, the "KILL" number for a particular radio comprises of the radio's decode number + D + the radio's KILL number. With DTMF signalling systems, the "KILL" number for a particular radio comprises of the radio's decode number + A + the radio's KILL number. In the case of DTMF signalling, both the decode number and the KILL number must have more than four digits. 4.4.4.1 Kill Signalling Operation Press [SHIFT] and the press [6] to place the KG510 into the KILL mode. The LCD display will indicate that the KG510 is in the KILL mode RX TX CH01 Kyodo-co Kill Pass -- Enter the required password by entering the correct four digit number. If the password has been correctly entered, the LCD display will show this message: RX TX CH01 Kyodo-co Kill Pass OK Then enter the "KILL" data from the keyboard that comprises of the decode number + D + the KILL number of the radio to be "KILLED". (In the case of DTMF signalling, it will be necessary to substitute the "A" tone instead of the "D" tone). Then press [#] to transmit the data. 133838 Page #14 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL If the incorrect password has been entered, the LCD display will show the following message: RX TX CH01 Kyodo-co Kill Pass NG If you enter the "KILL" data prior to entering the KILL password, and then press the [#] key, the LCD display will show the following message: RX TX CH01 Kyodo-co Input Password If the incorrect password has been entered more than the allowed number of tries, then the KG510 becomes disabled and the following message is displayed in the LCD display: Not Ready In such cases, it is necessary to return the KG510 to your radio supplier to have the KG510 repaired. 4.5 Scanning The KG510 is supplied with two scanning modes. These are All Channel Scan mode in which the KG510 will scan all channels that are programmed into the KG510, and the Program Channel Scan mode in which the KG510 will scan only the channels that have been designated during the programming of the KG510 transceiver. Furthermore, one HIGH priority, and one LOW priority scan channel can be set for each scan mode during the programming of the radio. 4.5.1 All Channel Scan Operation Pressing the [SCAN] key places the KG510 into All Channel Scan mode and the Scan mode symbol " " is displayed in the LCD display. Also the LCD will display "All Scan Mode-in" for two seconds as shown below: RX ====== TX CH01 Kyodo-co • All Scan Mode-in 133838 Page #15 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.5.2 Program Channel Scan Operation Pressing the [SHIFT] and then the [SCAN] key places the KG510 into Program Channel Scan mode and the Scan mode symbol " " is displayed in the LCD display. Also the LCD will display "PRG Scan Mode-in" for two seconds as shown below: RX ====== TX CH01 Kyodo-co • Prg Scan Mode-in 4.5.3 Exiting All Channel Scan and Program Channel Scan modes Pressing the [SCAN] key will take the KG510 out of either scanning mode and return the KG510 to normal mode. The scan symbol " " will be removed from the LCD display and the LCD will display "Scan Mode-out" for two seconds as shown below: RX ====== TX CH01 Kyodo-co Scan Mode-out 4.5.4 Priority Scanning The KG510 allows users to firstly enter the required scanning mode, and then they can enable Priority Scanning for the particular scanning mode chosen. Pressing the [SHIFT] key and then the [9] key places the KG510 into Priority Scanning mode as shown below: RX ====== TX CH01 Kyodo-co • Priority Scan Pressing the [SHIFT] and the [9] keys again will take the KG510 out of Priority Scan mode and return to the Normal Scan mode as shown below: RX ===== TX CH01 Kyodo-co • Normal Scan 133838 Page #16 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.5.5 Removing an Active Channel from the Scan List It is possible to temporarily delete an active channel from the scan list by pressing [SHIFT] and the [ ] key and holding the [SHIFT] and the [ ] keys depressed for more than one second. More than one channel can be deleted from the Scan list, provided that at least one channel remains in the Scan List. A "beep" sound from the radio confirms correct deletion of the channel from the scan list. This function CANNOT be used in the Priority Scan mode. The KG510 automatically restores all channels to their respective scanning list as soon as the KG510 exits from the scan mode. 4.5.6 Restoring Channels to the Scan List Channels can be restored to the scanning list without exiting from the scan mode by pressing the [SHIFT] key and pressing and holding the [A] key depressed for more than one second. This action will restore all channels to the scan list. This action CANNOT be used in the Priority Scan mode. 4.6 Locking the Keypad Pressing the [SHIFT] key and then the [8] key will lock all keys (except the [SHIFT] and [MON] keys) on the KG510's keypad to prevent accidental or inadvertent entry of data. After pressing the [SHIFT] and [8] keys the keypad becomes locked and the Key-Lock symbol is displayed in the LCD display. The display also shows "Key-Lock" for two seconds as shown below: RX ====== TX CH01 Kyodo-co • Key Lock Pressing [SHIFT] and [8] again will Unlock the keypad, remove the Key-Lock symbol from the LCD display, and display "Key-Unlock" in the LCD display for two seconds as shown below: RX ====== TX CH01 Kyodo-co Key Unlock 133838 Page #17 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.7 Changing Tone Signalling Systems It is possible to switch the KG510's tone signalling system among 5-Tone sequential signalling, DTMF signalling and Non(No-Tone system) (providing the field was set to "ENABLE" during the programming of the KG510). Press [SHIFT] and keep depressed the [0] key for more than one second to change among 5-Tone system, DTMF system and Non and indicate new signalling system in the LCD display as follows: RX ====== TX CH01 Kyodo-co System is DTMF Pressing [SHIFT] and pressing the [0] key for more than one second again will change next the signalling system and indicate new signalling system in the LCD display as shown below: RX ======= TX CH01 Kyodo-co System is Non 4.8 Displaying the Channel Information The KG510 can display information pertaining to the selected channel (provided that the field was set to "ENABLE" during the programming of the radio. This information is: The RX frequency of the selected channel. The TX frequency of the selected channel. The channel spacing for the selected channel (Wide or Narrow). The operating mode for the selected channel (Base, Repeater, simplex, duplex) The RX CTCSS/DCS tone for the selected channel (provided CTCSS/DCS has been programmed for use on the selected channel). The TX CTCSS/DCS tone for the selected channel (provided CTCSS/DCS has been programmed for use on the selected channel). The tone encoding format (providing 5-Tone signalling was selected during programming of the KG510). The tone set (providing 5-Tone signalling was selected during programming of the KG510). The ANI mode. The tone decoding set (provided 5-Tone or DTMF signalling was selected during programming of the KG510). The decode number (provided 5-Tone or DTMF signalling was selected during programming of the KG510). 133838 Page #18 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL To view this information in the LCD display, firstly select the required channel. Then press the [SHIFT] key and then the [7] key. You will need to keep the [7] key pressed until the KG510 has cycled through the information steps. This function is NOT available if the field has been set to "DISABLE" during the programming of the KG510. 4.9 Display of Received Tone Frequencies. It is possible to set the KG510 to display the received tone frequencies in the LCD display in the area normally used to display the strength of the received signals. Press [SHIFT] and then press [D] to enable this function. Once enabled, the LCD will show "RCV" in the area of the LCD display that normally shows the strength of the received signal, as well as "Tone Display on" for two seconds as shown below: RCV TX CH01 Kyodo-co Tone Display On Then, whenever a tone frequency is decoded, the frequency number will be displayed in the LCD display to the right of "RCV" as shown below: RCV 12345 TX CH01 Kyodo-co 5TON Pressing the [SHIFT] key and then the [D] key once again will disable this function and return the LCD display to normal as shown below: RX TX CH01 Kyodo-co Tone Display Off 133838 Page #19 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.10 Bar Graph Displays The KG510 will normally show the strength of the received signal to the right of "RX" in the LCD display, and the strength of the transmitted signal to the right of "TX" in the LCD display, both in the form of a bar graph. This function can be disabled by pressing the [SHIFT] key and then the [CH] key. The LCD display will indicate "RX Display Off" and "TX Display Off" as shown below: RX Display Off TX Display Off CH01 Kyodo-co Pressing the [SHIFT] key and then the [CH] key once again will return the KG510 to normal and the LCD display will show the normal bar graph display for both the RX signal strength and TX signal strength. 4.11 LCD Display Back Light The LCD Display has a Back-Light to illuminate the display. It normally switches "ON" whenever any key or the PTT lever is pressed, and will remain illuminated for five seconds after the most recent key press. Some users may prefer the Back-Light to remain illuminated to assist viewing the LCD display in poor viewing situations. Press the [SHIFT] key and then press the [1] key for more than one second and the LCD Back-light will remain illuminated. Once again, press the [SHIFT] key and then press the [1] key for more than one second and the LCD Back-light will revert to normal operation. 4.12 Transmit Power Change It is possible to change the KG510's transmit power from the high power setting to the low power setting from the keypad and vice versa (provided that this function has been enabled during the programming of the KG510). To enable this function, the field must be set to "ENABLE". Press the [SHIFT] key and the [2] key and the KG510 will change from the high transmit power setting to the low transmit power setting, and the " “symbol will be removed from the third line of the LCD display. Press the [SHIFT] key and the [2] key a second time, and the KG510 will change from the low transmit power setting to the high transmit power setting, and the " " symbol will be displayed in the third line of the LCD display. If this function is NOT required, the field must be set to "DISABLE". 133838 Page #20 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.13 Calling Party ID Display The KG510 has the capability to display a calling radio's ID (ANI) number after being called. When the KG510 is called, "CALL" will be displayed on the fourth line of the LCD display (and continue to flash) and the calling radio's ID number will be displayed to the right of "CALL" as shown below: RX TX CH01 Kyodo-co CALL 12346 If the KG510 user presses the [#] key (when "CALL" is flashing and the caller's ID number is displayed), the KG510 will automatically call the identified radio. In the case of 5-Tone signalling systems, this function is enabled in the <5Tone Encode Menu> field, by selecting one of the following parameters: "Encode + B + Decode" "Encode + A.Pause + Decode" "Decode + A.Pause + Encode" "Encode + ANI" In the case of DTMF signalling systems, this function is enabled by setting the field to "ON" during the programming of the KG510. 4.14 Displaying any Radio's ID Number The KG510 has the capability to display any calling radio's ID (ANI) number. When the KG510 receives an ANI number, "DISP" will be displayed on the fourth line of the LCD display (and continue to flash) and the radio's ID number will be displayed to the right of "DISP" as shown below: RX TX CH01 Kyodo-co DISP 1234 In the case of 5-Tone signalling systems, this function is enabled by setting the <5Tone Decode Menu> field to "ON" during the programming of the KG510. In the case of DTMF signalling systems, this function is enabled by setting the field to "ON" during the programming of the KG510. 133838 Page #21 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.15 Emergency Caller Display The KG510 has the ability to accept and display emergency calls from other radios within the radio system This function is enabled by setting the field to "ON" in the <5Tone Decode Menu> or during the programming of the radio. The calling (Emergency) radio must encode its emergency data in the following format: "000" + the calling radio's ID (decode number). This format applies to both 5 Tone and DTMF signalling systems. When the KG510 receives an emergency call, the KG510 will sound a warning tone from the speaker, display "EMG" (flashing) in the fourth line of the LCD display, and display the emergency radio's ID to the right of "EMG" as shown below: RX TX CH01 Kyodo-co EMG 12346 Upon receipt of an emergency call, the KG510 will automatically respond to the emergency radio by sending the emergency radio's ID number to it. If the KG510 user presses the [#] key, the KG510 will resend the emergency radio's ID number. While the KG510 is in the Emergency Mode, all keys (except the [#] key) on the keyboard become disabled. Pressing the [SHIFT] key and the [ ] key will return the KG510 to the normal operating mode. 4.16 Automatic Transmit in Repeater Mode The KG510 can be programmed to automatically repeat valid incoming messages. Firstly, the active channel of the KG510 must be programmed to operate as a repeater. It must then receive a carrier frequency on the designated channel. If the KG510 has been programmed for CTCSS or DCS operation, it must also receive a valid CTCSS or DCS tone. It will then automatically retransmit any received signals. When the KG510 ceases to receive a carrier frequency, or a valid CTCSS or DCS tone, it activates the timer. This will keep the KG510 repeating (for up to 9.9 seconds depending on the programming of the KG510), and allow other users with a valid CTCSS or DCS tone to access the repeater. 133838 Page #22 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.17 TX Test Mode The KG510 is provided with a TX (Transmit) Test Mode. When the KG510 is placed in the TX Test Mode, it will transmit a carrier frequency modulated with a 1KHz tone on the selected active channel. It is possible to change channels while in TX Test Mode. Pressing the [SHIFT] key and then the [B] key places the KG510 in TX Test Mode and displays the message in the LCD as shown below: RX TX CH01 Kyodo-co TXT TX Test Mode-in Pressing the [SHIFT] key and the [B] key a second time will return the KG510 to normal mode and displays the message in the LCD as shown below: RX TX CH01 Kyodo-co TXT TX Test Mode-out 4.18 Keypad Test Mode The KG510 is provided with a Keypad Test Mode that allows the user to electrically test all keypad keys as well as the PTT Key. Holding the [C] key pressed while switching the POWER SWITCH "ON" places the KG510 in Keypad Test Mode and displays the message in the LCD Display as shown below: KEY TEST Please Key-in Then press the keys to be tested one at a time. The respective key will be displayed in the LCD when the key is operating correctly. e.g. If you press the [CH] key, the LCD Display will indicate correct operation as shown below: KEY TEST CH Key Switch the KG510 "OFF" to exit this Keypad Test Mode. 133838 Page #23 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.19 Frequency Band Test Mode It is possible to display the KG510's operating Frequency Band in the LCD display when in Frequency Band Test Mode. Holding the [B] key pressed while switching the POWER SWITCH "ON" places the KG510 in Frequency Band Test Mode and displays the operating Frequency Band in the LCD Display as shown below: > 40D OK "40D" indicates the frequency band for a particular KG510 radio. Switch the KG510 "OFF" to exit the Frequency Band Test Mode. 4.20 Starting Message When the KG510 is Switched "ON", it will display a Starting Message in the LCD display for two seconds. The default Starting Message (using all dots) is shown below: ••••••••••• ••••••••••• • <51BS V095 510>• ••••••••••• A personalised message for your business may be shown as the Starting Message. If you require a personalised message, then it should be entered in the field during the programming of the radio. Such a message is shown below: Kyodo-co Japan <51BS V095 510> 133838 Page #24 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.21 Serial Number Display It is possible to display the KG510's Serial Number in the LCD Display. To do so, the Serial Number must be entered into the field during the programming of the radio. The serial number can be up to eight characters long and can comprise of any of these characters: "A - Z" & "0 - 9". Holding the [D] key pressed while switching the POWER SWITCH "ON" places the KG510 in Serial Number Display Mode and displays the KG510's Serial Number in the LCD Display as shown below: Serial KY000727 Switch the KG510 "OFF" to exit from the Serial Number Display Mode. 4.22 EEROM Data Check Mode As soon as the KG510 is switched "ON", it will automatically read and check all the data in the EEROM. If this check finds damaged or corrupted data, the KG510 will automatically enter the Programming Mode and display the following message in the LCD Display: EROM Data Error Should this happen, it is necessary to return the KG510 to your radio supplier or to a competent radio trades-person who has the facilities to reprogram the KG510. 133838 Page #25 of 26 Pages 24 January, 2001 KYODO KG510 OPERATORS MANUAL 4.23 Hardware Error Detection The KG510 automatically tests for certain hardware faults or failures, and when a fault is found, it will blink the "ALM" LED display above the LCD Display and indicate the nature of the fault in the LCD Display as shown below: RX TX CH01 Kyodo-co RX PLL Error This figure indicates an RX PLL error. RX TX CH01 Kyodo-co TX PLL Error This figure indicates a TX PLL error. RX TX CH01 Kyodo-co PA Error This figure indicates a PA error. Should the KG510 indicate any of these errors, then it is necessary to return the KG510 to your radio supplier or to a competent radio trades-person to have the fault remedied. 4.24 RS232C Communications Error If a fault is encountered during programming of the KG510, one of the following messages may be displayed in the LCD Display: ! Over Run Error ! Framing Error ! Parity Error ! Unknown Command ! Data Unmatch ! Send Error ! Answer Timeout ! Receive Timeout Please switch the KG510 "OFF", and then back "ON", and retry reprogramming the KG510 again, should any of the above error messages be displayed in the LCD Display. 133838 Page #26 of 26 Pages 24 January, 2001