MilDef Crete RT9 13" Notebook User Manual UM
MilDef Crete Inc. 13" Notebook UM
Users Manual
NOTEBOOK COMPUTER RT9 Preliminary User’s Guide Notice The company reserves the right to revise this publication or to change its contents without any notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. Any of the software described in this manual is sold or licensed "as is". Should the programs prove defective following purchase, the buyer (and not the manufacturer, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any software defects. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intender as an endorsement of that product or its manufacturer. Copyright © 2010 CReTE Systems Inc Trademarks All other brand and product names are trademarks or registered trademarks of their respective companies. Regulatory Information/ Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. II FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If not being installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC Caution To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). III FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. III CE Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN55022 EN55024 LVD (CISPR 22) Radio Frequency Interference (EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61000-3-2, EN61000-3-3) Generic Immunity Standard EN 60950 Product Safety, IEC 60950-1: 2005 R&TTE (CE) Manual Regulatory Requirement WLAN - IEEE 802.11a/b/g/n 802.11a/b/g/n Restrictions: European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz. In France, the equipment must be restricted to the 2.4465-2.4835 GHz frequency range and must be restricted to indoor use. III CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (89/336/EEC), Low-voltage Directive (73/23/EEC), the Amendment Directive (93/68/EEC), and the procedures given in European Council Directive (99/5/EC and 89/3360EEC). The equipment was passed, and the equipment test was performed according to the following European standards: EN 300 328 V1.7.1:2006 EN 301 893 V1.4.1(2007-07) EN 301 V1.8.1 2008-04 / EN 301 489-17 V1.3.2 2008-04 EN 50371:2002 EN 60950-1: 2005 UL, TÜV AC Adapter (TÜV includes EN60950 LVD) VI Environmental Information, Material Safety & Recycling All materials used in the manufacturing of this equipment are recyclable or environmentally friendly. Please recycle the packing materials by the local regulations at the end of the product's service life. Notice: z The equipment may still contain tiny amount of hazardous substances for health and environment, though those are below control level. z To avoid spreading such substances into the eco system, and to minimize the pressure on the natural, you are encouraged to use the appropriate take-back for reusing or recycling most of the materials in a safe way after the service life. z The crossed bin symbol indicates proper disposal is required. z For more information on collection, reuse and recycling, please consult the local or regional waste administration for more information. z You can also contact with the dealer for more information on the environmental details of the equipment. VII CONTENTS CHAPTER ONE- GETTING STARTED ................................................. 1 UNPACKING ..............................................................................................................................1 QUICK OPERATION ...................................................................................................................2 APPEARANCE OVERVIEW .........................................................................................................3 CHAPTER TWO- OPERATING INFORMATION ................................... 8 WORKPLACE.............................................................................................................................8 RUGGEDNESS ..........................................................................................................................8 SHUT DOWN ...........................................................................................................................10 SLEEP/ HIBERNATE ................................................................................................................10 HARD DISK DRIVE (HDD)......................................................................................................12 ODD (OPTICAL DISK DEVICE)...............................................................................................12 EXPRESS AND PCMCIA CARDS............................................................................................13 RTC .......................................................................................................................................13 REPLACING MODULES ...........................................................................................................14 WIRELESS DEVICES (OPTIONAL) (TBD) ...............................................................................15 AC ADAPTER..........................................................................................................................21 BATTERY ................................................................................................................................22 CHAPTER FOUR- BIOS SETUP ......................................................... 26 MAIN MENU ............................................................................................................................26 SATA PORT 1 SUB-MENU.....................................................................................................28 SATA PORT 2 SUB-MENU.....................................................................................................29 ADVANCED MENU ..................................................................................................................30 SIO SMC27 CONFIGURATION SUB-MENU .....................................................................33 SECURITY MENU ....................................................................................................................35 RF INTERFACE CONTROL SUB-MENU ...................................................................................37 BOOT MENU ...........................................................................................................................38 EXIT MENU .............................................................................................................................39 CHAPTER FIVE- SPECIFICATION ..................................................... 40 CPU .......................................................................................................................................40 MEMORY.................................................................................................................................40 DISPLAY..................................................................................................................................40 KEYBOARD .............................................................................................................................41 TOUCHPAD .............................................................................................................................41 HARD DISK DRIVE ..................................................................................................................41 DVD SUPER MULTI DRIVE.....................................................................................................41 AC ADAPTER..........................................................................................................................42 BATTERY ................................................................................................................................43 SYSTEM UNIT DIMENSIONS AND WEIGHT..............................................................................43 MATERIALS AND RECYCLING .................................................................................................44 ENVIRONMENTAL ....................................................................................................................44 CHAPTER SIX- OPTIONAL DEVICES ................................................ 45 MEMORY CARD ......................................................................................................................45 VEHICLE ADAPTER .................................................................................................................45 2ND BATTERY ..........................................................................................................................45 2ND HDD .................................................................................................................................45 ODD (OPTICAL DISK DRIVE) .................................................................................................46 HEATER ..................................................................................................................................46 LAN AND MODEM CARD ........................................................................................................46 WIRELESS LAN CARD ...........................................................................................................46 KB DUST COVER ...................................................................................................................47 PCMCIA COVER ...................................................................................................................47 BUILT-IN VEHICLE ADAPTER ..................................................................................................47 DUAL-BAY BATTERY CHARGER .............................................................................................48 CHAPTER SEVEN- UTILITIES AND DRIVERS .................................. 49 CHIPSET DRIVER ....................................................................................................................50 GRAPHIC CONTROLLER .........................................................................................................50 AUDIO .....................................................................................................................................50 MINI PCI-E 1G RTL8111B LAN DRIVER.............................................................................50 MINI PCI INT8100 LAN DRIVER...........................................................................................51 MODEM DRIVER (OPTIONAL) .................................................................................................51 TOUCH PANEL (OPTIONAL)....................................................................................................51 WIRELESS LAN DRIVER (TBD) (OPTIONAL).........................................................................51 GPS DRIVER (TBD) (OPTIONAL) ..........................................................................................51 WWAN DRIVER (TBD) (OPTIONAL) .....................................................................................51 WIRELESS MANAGER .............................................................................................................52 CHAPTER EIGHT– MAINTENANCE AND SERVICE ......................... 53 CLEANING ...............................................................................................................................53 TROUBLESHOOTING ...............................................................................................................53 RMA SERVICE .......................................................................................................................54 Getting Started Chapter One- Getting Started Unpacking The following components are along with your notebook computer. If there is any missing or damaged, please contact with your dealer immediately. Computer Unit Removable HDD (Hard Disk Drive) Removable ODD (Optical Disk Drive) AC Adapter AC Power Cord Utility DVD User Guide Carrying Bag Chapter One - 1 Getting Started Quick Operation Loosen the battery screw, remove the battery insulation sheet, and mount the battery. Connect the AC adapter with the computer and start charging the battery for at least 10 minutes. Turn ON the computer by pressing the Power Switch. Notice: z When ambient temperature is under +5℃ (This is the default setting for this computer.), the system may not boot up immediately. System will beep with LED heater light flashing to remind the user while heater working. Also, the frequency of the LED will become faster to remind the user while the temperature is approaching to be suitable. After 5~15 minutes, the system will boot up automatically. z Under an emergency situation, it is able to skip heating for booting up the system immediately by pressing the power switch for >9 seconds. The speaker will also beep with a special sound. (It is not guaranteed all devices on the computer are possible to work properly.) z Press the power switch again during the heating process will shut down the computer. z Driver or application software installation may be necessary for further operation. z The following procedures will help to Turn OFF the computer: 1. Press power switch to “Shut Down”, “Sleep”* or “Hibernate”* dependending on operating system (OS) and power management settings. 2. Press power switch for 4 seconds for a “Hard” power off. But the system will shut down immediately without saving any data or parameters. 3. Click Start → Shut Down in Windows to Turn OFF. Note: ¾ Some operating systems may not support the above-mentioned functions. Chapter One - 2 Getting Started Appearance Overview LCD Panel Open 1. 2. 3. 4. 5. 6. 7. Heater BT/WLAN/GPS Keyboard Number Lock Keyboard Caps Lock Keyboard Scroll Lock HDD in Use Secondary Battery Charge 8. 9. 10. 11. 12. 13. Primary Battery Charge Power Indicator Power Switch Touchpad Left Button Touchpad Touchpad Right Button Chapter One - 3 Getting Started Right View ○ 2 ○ ○ 1. Flex Bay: a. Standard: SATA ODD b. Optional: 2nd SATA HDD or 2nd Battery 2. Eject Button 3. In-use Indicator Light 4. 1st SATA HDD Chapter One - 4 ○ Getting Started Left View 1. PS/2 Port (KB + Mouse) 2. IEEE1394 Port (Fire Wire) 3. Optional: Modem Jack RJ11 4. LAN RJ45 5. USB Port (Universal Serial Bus) 6. External Speaker & Ear phone Jack 7. USB Port (Universal Serial Bus) 8. Line In Jack 9. USB Port (Universal Serial Bus) 10. Microphone Jack 11. Optional: Serial Port DB9 (COM 3) 12. Express Card Slot x 1 & PCMCIA II Slot x 1 (Optional: PCMCIA x 2) 13. Optional: Serial Port DB9 (COM 4) Chapter One - 5 Getting Started Rear View 1. 2. 3. 4. 5. 6. 7. Optional: Military Connector Port DC Power Jack Serial Port DB9 (COM1) RGB DB15 Port Docking Port Printer Port Serial Port DB9 (COM2) Chapter One - 6 Getting Started Bottom View ○ ○ ○ ○ ○ 1. Primary Battery 2. ODD Latch 3. HDD Latch Chapter One - 7 Operating Information Chapter Two- Operating Information Workplace A clean and moisture-free environment is preferred. Make room for air circulation. Remember to avoid areas from: Sudden or extreme changes in temperature. Extreme heat. Strong electromagnetic fields (near television set, motor rotation area, etc.). Dust or high humidity. If it is necessary to work in a hostile environment, please regularly maintain your notebook computer by cleaning dust, water, and etc. to keep it in an optimal condition. Ruggedness This notebook computer is designed with rugged features such as vibration, shock, dust, and rain/ water protection. However, it is still necessary to provide appropriate protection while operating in harsh environments. The notebook computer is also designed to withstand rainfall from top with mild wind blowing only. Please keep the keyboard facing up, i.e. normal operating direction, to maintain water resistance. NEVER immerse the unit in water, or spray water at an upside-down system. Doing so may cause permanent damage. The D-sub connector caps on the rear of the computer are for dust and shock protection. The connectors are sealed internally. Other I/O ports Chapter Two - 8 Operating Information and devices on the left or right must have caps tightly closed or cable inlets sealed while being exposed to water or dust. There are optional gaskets for DB-9 and DB-25 connectors. You may install them to improve rain/ dust/ moisture resistance on your commercial type cable. Insert the packing into the male connector (with pins) and fasten the screws. All connectors will be corroded if being exposed to water or moisture. Corrosion is accelerated if the power is ON. Please take proper water-resistant measures for cable connections. The DC jack and cables are sealed and may be operated with water splashing while attached. All port covers should be in place when no cable is attached. Operating System This notebook computer is compatible with most operating systems (OS). However, not all functions are 100% compatible. For example, ACPI, Smart Battery, and etc. are not available on DOS, and other non-Microsoft OS. Consequently “Standby”, “Hibernation”, “Battery Gauge”, and etc. would not work under such operating systems. Boot Up and POST Boot up The computer turns ON and loads the operating system (such as Windows) into the system memory. This start-up procedure is called “boot up”. The ROM BIOS Power on Self-Test (POST) Each time the computer powers on, it automatically performs a self-test of its memory and hardware devices. Chapter Two - 9 Operating Information Shut down Before shutting down, please always remember to save the unfinished works and close the application for preventing from any possible data loss or HDD damage. “Shut down” will totally turn OFF the power of your notebook computer. If you want to start your notebook computer again, you need to press the power switch. Sleep/ Hibernate Sleep Under “Sleep” mode, the system will temporarily save your work into RAM. You are able to do enter “Sleep” mode by directly clicking from your OS. Or, you can do the “Sleep” Mode settings in your OS. If you want to start your notebook computer again, all you need to press any key. Hibernate Under “Hibernate” mode, the system will save your work into HDD. You are able to do enter “Hibernate” mode by directly clicking from your OS. Or, you can do the “Hibernate” Mode in your OS. If you want to start your handheld computer again, you need to press the power switch. Note: ¾ Standby/Hibernate/Resume works with both AC adapter and battery. The power management functions may not work under non-ACPI operating systems. ¾ If you work under Windows 7 (64 bit) with external KB or mouse, please do the Windows Setting as follows: 1. External Mouse: Device Manager → Mice and other pointing devices → HID- compliant → Power Management → Disable “Allow this device to wake the computer” 2. External KB: Device Manager → Keyboards → HIDcompliant → Power Management → Disable “Allow this device to wake the computer” Chapter Two - 10 Operating Information Keyboard The keyboard is functionally equivalent to a full size desktop keyboard. A sample layout is shown below. The Numeric Keypad The numeric keypad functions are the same as an electronic calculator. It is embedded in the main keyboard, with the numeric figures printed on the upper right of their respective keys. There are keys for the digits 0~9, the decimal point ( . ), addition ( + ), subtraction ( - ), multiplication ( * ), and division ( / ) in the keypad. To activate the keypad, press the Num Lock key. There are 15 keys switching from alphabetic to numeric. Press Num Lock again to return. Chapter Two - 11 Operating Information Keyboard Backlight (Optional) Press [Fn] [F5] key for approximately 1 second to turn the keyboard backlight ON or OFF. Hard Disk Drive (HDD) The Hard Disk Drive (HDD) is a 2.5” type/ 9.5mm height standard SATA interface data storage device. HDD and ODD are removable. This design provides convenience and security. They can ONLY be removed when the power is OFF. Note: NEVER drop your HDD, ODD or expose them to high temperature, high humidity, or any hazardous environment. NEVER try to disassemble the module. Static discharge may destroy your device and data. Always pick up the modules by touching the case only. ODD (Optical Disk Device) There is a 5.25” type/ 12.7mm height standard SATA interface ODD. The actual device will depend on the model you purchased. The ODD may be used as a boot device if properly set in the BIOS. The ODD accepts a variety of standard 12cm CDs, DVD-ROM (Single Layer, Dual Layer), DVD-Video, DVD-R*10 (1.4 GB, 2.8 GB, 4.7GB), DVD-RW (Ver.1.1/1.2 1.4 Gx`B, 2.8 GB, 4.7 GB, 9.4 GB), DVD-R DL (8.5 GB), DVD-RAM (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB), +R (4.7 GB), +R DL (8.5 GB), +RW (4.7 GB), CD-Audio, CD-ROM (XA compatible), CD-R, Photo CD (multiple session compatible), Video CD, CD EXTRA, CD-RW, CD-TEXT and etc. Do not use the IDE-interface ODD; it may cause the computer malfunction. Chapter Two - 12 Operating Information The following procedure assumes that all the necessary ODD utilities were installed on the computer. For ODD utility installation, please refer to “Utilities and Drivers”. ODD also can be removed and swapped with the 2nd battery or 2nd SATA HDD. Put disk into the ODD While the power is ON, push the ejecting button of ODD. The tray will release. Then gently pull the tray out. Put the disk with its label facing up on the holder and push the tray back into the cabinet. Any dirt on the data side of the disk may cause to the erroneous read. Please avoid touching the data side. Read from the ODD The ODD may be designated as drive D: or higher depending on your configuration. You may access to it in DOS or Windows. Please avoid shock or vibration when the optical device is active. Express and PCMCIA Cards The computer supports one PCMCIA II and one Express card or two PCMCIA II cards. To remove the card, push the button on the right of the card to eject it. The ejecting button can hide into the compartment by pushing it inward gently. RTC Battery backed up RTC (Real Time Clock/Calendar) is built in an on-board CMOS (Complementary Metal Oxide Semiconductor) chip. The RTC keeps track of the time and date while the computer is off. The CMOS chip also stores system setup information. RTC battery is also recharged when AC adapter is attached. Recharge the computer approximately once per month to ensure RTC operation. Chapter Two - 13 Operating Information Replacing Modules To remove the modules: 1. Turn OFF the computer or hibernate. 2. Disconnect all cables from the computer. 3. Use a coin to turn and loose the screws on the modules. 4. Remove the battery from the compartment. 5. Push the latch knob to release the ODD or HDD module and push them outward. 6. Remove the module from the computer. To re-install the modules: Gently push the module into the slot. Fasten the screw to fix the module. Caution You must turn the power OFF before replacing the ODD and HDD modules. Chapter Two - 14 Operating Information Wireless Devices (Optional) (TBD) Before using wireless devices, please turn “ON” the Wireless Devices All ON/OFF Switch, and then use the Wireless Manager to do the rest settings. The following instructions are only for the models with optional Wireless Devices (Wireless LAN/ Bluetooth/ WWAN/ GPS) and taking the systems working under Windows 7/ 64-bit OS for example. Wireless LAN 1. Driver & Utility Installation: a. Install the Chipset Driver first: Insert the Utility DVD into the ODD. Click infinst_autol.exe in the directory of “RX9\Drivers\Chipset\Win7(64-bit)”, and then follow the prompt to complete installation. b. Then, install the Wireless Manager utility: Insert the Utility DVD into the ODD. Click setup.exe in the directory of Utilities\Wireless Manager then follow the prompt to complete installation. 2. Launch the Wireless Manager: a. Launch the Wireless Manager. b. Click “Wireless LAN” for enabling the Wireless LAN function (click again for disabling the WLAN function). Once the Wireless LAN starts up, the RF LED will turn on accordingly. Please see the illustration as below (with Wireless LAN function “ON”): Chapter Two - 15 Operating Information 2. Driver & Utility Installation: a. Install the WWAN driver first: Insert the Utility DVD into the ODD. Click Autorun.exe in the directory of “RF9\Drivers\WWAN\Win7(64-bit)”, and then follow the prompt to complete installation. b. Then, install the Wireless Manager utility: Insert the Utility DVD into the ODD. Click setup.exe in the directory of Utilities\Wireless Manager then follow the prompt to complete installation. 3. Launch the Wireless Manager: a. Launch the Wireless Manager. b. Click “WWAN” for enabling the WWAN function (click again for disabling the WWAN function). Once the WWAN starts up, the RF LED will turn on accordingly. Please see the illustration as below (with WWAN function “ON”): Chapter Two - 16 Operating Information DockUnder DockUnder is utilized for system unit docking. AC adapter or vehicle adapter should attach directly to DockUnder and automatically charge the computer while docked. Ports 1. 2. 3. 4. 5. 6. 7. 8. 9. Serial Port DB9 (COM2) Serial Port DB9 (COM1) PS/2 (KB with Mouse) USB #1 & #2 RGB DB15 DVI Port LAN RJ45 (10M/100M) Antenna Hole (Reserved for Wireless Signals) DC Jack Chapter Two - 17 Operating Information Mounting the DockUnder: 1. 2. 3. 4. Turn OFF the power. Open the rubber cap of the docking connector. Align the docking connector. Push the computer to join the guiding pins. Do not lift the computer up while docking. 5. Metal bar is drawn outward. Note: ¾ Do not lift up the computer while engaging. Chapter Two - 18 Operating Information 1. 2. 3. 4. Pull up the metal bar. Move forward inside. Lock along the direction of the clock. Key Locked with Electric Power ON/OFF. While turn on the power of DockUnder with the Key that can use all the functions on DockUnder. Meantime Computer will also have the power. There are 1*PCI+1*PCIe slots on the DockUnder. Maximum card dimensions are 260mm (L: length, including L-bracket thickness) x 115mm (W: width, including gold fingers) x 25 mm (H: height). The total power rating of 2 PCI slots is +5V 3A, +3.3V 3A, +12V 300mA, and -12V 300mA. 5. Power On/Off with Computer. The Power On/Off can be replaced for Computer itself. Chapter Two - 19 Operating Information To install expansion card in DockUnder: 1. Unplug the AC adapter. 2. Release and remove the computer. 3. Remove the screws on the upper and lower covers. 4. Open the upper cover. 5. Install the expansion card into the slot and fix the L-bracket. 6. Assemble the upper cover. 7. Attach the computer and perform functions test. Note: ¾ Please check IRQ conflict before installing cards and drivers. ¾ Never dock or un-dock the computer while power is ON. IRQ DMA 0. 1. 2. Timer output 0 Sound KB Sound 8 RTC FDD 9 ACPI (or Free) Reserved (or ECP/EPP) 10 Free (16-bit PCMCIA, or COM3*) 11 PCI devices or Card Bus 0/1 (Sound, LAN*, 32-bit PCMCIA, etc.) 12 Touch pad (PS/2 mouse) 13 Co-processor 14 HDD 15 DVD-ROM drive 3. COM2 (or Fax/Modem*, IrDA) 4. COM1 (or Touch screen) 5. Free (COM4*) 6. FDD 7. Parallel port 1 *: Optional devices. Chapter Two - 20 Managing Power Chapter Three- Managing Power AC Adapter The AC adapter performs two functions: It powers the computer from an external AC source. It charges the computer battery. The adapter automatically detects the AC line voltage (100V or 240V) and adjusts accordingly. The following are recommended when using the AC adapter: Use a properly grounded AC outlet. Use one AC outlet exclusively for the computer. Having other appliances on the same line may cause interference. Use a power strip with built-in surge protection. Connecting the AC adapter: Plug the AC cord to the adapter. Plug the other end of the AC cord into the wall outlet. Make sure the green LED on the adapter turns on. Attach the DC plug into the power jack of the computer; turn the lock ring clockwise to secure it. AC Adapter Indicator: The green LED indicates that AC power is ready. Chapter Two - 21 Managing Power Battery The power source will automatically switch to battery when the external power source (AC adapter or optional vehicle adapter) is disconnected. Battery Low When the battery is nearly exhausted, the computer gives the following “Battery Low” warnings: z Windows battery low warning (when operating system is Windows) z The power LED flashes. Once the Battery Low warning occurs, please: z Save and close the files you are currently working on. z Plug in the AC adapter to recharge the battery. Charging the Battery Plug in the AC adapter (or optional vehicle adapter) to start the battery charging. If the battery is already full, the sense circuitry will stop high current charge within several minutes. There are two LED indicators next to the power indicator for the Primary and Secondary battery respectively. Indicator turns ON when the battery is charging and turns OFF when the battery charging is completed. To charge the Secondary battery, simply install it into the computer and attach the AC adapter. The internal charger will charge the Primary battery first. The Secondary battery will be charged once the Primary battery charges full. Optional Dual Battery Charger can charge the Primary and Secondary batteries externally. Chapter Two - 22 Managing Power Battery Charging Notice The followings are the detailed information for charging the Primary and Secondary batteries under AC and DC modes: AC mode: z When the Power Status is changed and AC mode is detected, the Primary battery will be charged. z Until the Primary Battery is finished charging, then it will continue to charge the Secondary Battery fully also. z When batteries are all full, the EC (embedded controller) will be turned off. z If there is no Power Status change, until the capacity is down below 90%, a natural discharging occurs, and then recharge again. DC mode: z When DC mode is detected, it will discharge the Secondary Battery until the capacity is below 10%, and then switch to the Primary Battery for continuing discharging. z When the capacity of the Primary Battery is below 10%, the Low Battery LED will flash. Battery Gauge You may check battery status from battery gauge in Windows. Click the power/battery icon to reveal the battery gauge window. Chapter Two - 23 Managing Power Battery Power Saving Tips The computer comes with an intelligent power-saving feature. You may extend the battery life by: z Setup power saving functions in Operating System Power Management options (e.g. Windows Power Options). z Lower the intensity of the display by brightness control. z Use standby option when computer is temporarily not in use. z Shut down the computer when it will not be for a long-time use. Replacing Battery When the battery is nearly exhausted, there are two ways to keep your handheld computer working. Connect the AC adapter and the power cord designed for this handheld computer to start charging is one method; directly replace a charged battery designed for this handheld computer may be the other one. Note: ¾ Always remember to turn OFF the power before replacing the battery. Power Conservation This computer consumes much less power than conventional computers. However, power consumption may be reduced by configuring the Power Management Setup properly. It is recommended the power saving functions to be enabled even when not running on battery power. Power Management will not degrade performance while saving power. Chapter Three - 24 Managing Power Supporting ACPI Your notebook computer supports ACPI (Advanced Configuration and Power Interface) for power management. With ACPI and an ACPI-compliant operating system such as Windows, the feature will allow you to reduce the power consumption for energy saving. By supporting ACPI, the AC adapter LED and the Power indicator LED will show in different ways. The followings are the detailed description. Sleep: AC adapter LED is ON (while connecting with power) Power LED indicator is ON; Other LED indicators are OFF Under Hibernation: AC adapter LED is ON (while connecting with power) Power LED indicator is OFF; Other LED indicators are OFF Shutdown: AC adapter LED is ON (while connecting with power) Power LED indicator is OFF; Other LED indicators are OFF Chapter Three - 25 BIOS Setup Chapter Four- BIOS Setup Press [F2] at boot up to enter BIOS setup. Use arrow keys to select options and [+/-] to modify them. When finished, move to” Exit” and press [Enter] then confirm save by pressing [Y]. Main Menu Phoenix SecureCore (tm) Setup Utility Advanced Security Boot Main ► SATA Port 1 ► SATA Port 2, , or selects field. [Auto] [Auto] System Memory: Extended Memory: F1 Help Esc Exit Item Specific Help [15:48:04] [10/02/2010] System Time: System Date: ↑↓ Select ↔ Menu Exit 632 KB 1012736KB Item –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Note: ¾ The contents may vary depending on computer configurations. Main Menu Selections You can make the following selections on the Main Menu. Use the sub-menus for other selections. Feature System Time System Date SATA Port 1~2 Options HH:MM:SS MM/DD/YYYY None Description Set the system time Hour, Minute, Second. Set the system date Month, Day, Year. Auto-detect the device, then show the device. Chapter Four - 26 BIOS Setup General Help Window Pressing or at any menu brings up the General Help window that describes the detailed keys and functions for setup. The scroll bar on the right of any window indicates that there is more than one page of information in the window. Use and to display all the pages. Pressing and displays the first and last page. Pressing displays each page and then exits the window. Press to exit the current window. Chapter Four - 27 BIOS Setup SATA Port 1 Sub-Menu Phoenix SecureCore (tm) Setup Utility Main SATA Port 1 Item Specific Help [Auto)] User = you enter parameters of hard-disk drive installed at this connection. Auto = autotypes hard-disk drive installed here. CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. [Auto] LBA Format Total Sectors: 78140160 Maximum Capacity: 40008MB Type: Multi-Sector Transfers: LBA Mode Control: 32 Bit I/O: Transfer Mode: Ultra DMA Mode: F1 Help Esc Exit ↑↓ Select ↔ Menu [16 Sectors] [Enabled] [Disabled] [FPIO 4/ DMA 2 ] [Mode 5] Item –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit SATA Port 1 Sub-Menu Selections You can make the following selections on the SATA Port 1 Sub-Menu. Feature 32 Bit I/O: Options Enabled Disabled Description This setting enables or disables 32 bit IDE data transfers. Chapter Four - 28 BIOS Setup SATA Port 2 Sub-Menu Phoenix SecureCore (tm) Setup Utility Main SATA Port 2 Item Specific Help [Auto] User = you enter parameters of hard-disk Multi-Sector Transfers: [Disabled] drive installed at this LBA Mode Control: [Disabled] connection. 32 Bit I/O: [Disabled] Auto = autotypes Transfer Mode: [Standard ] hard-disk drive installed Ultra DMA Mode: [Mode 5] here. SMART Monitoring: Disabled CD-ROM = a CD-ROM drive is installed here. ATAPI Removable = removable disk drive is installed here. F1 Help ↑↓ Select Item –/+ Change Values F9 Setup Defaults Esc Exit ↔ Menu Enter Select ► Sub-Menu F10 Save and Exit Type: [Auto] SATA Port 2 Sub-Menu Selections You can make the following selections on the SATA Port 2 Sub-Menu. Feature 32 Bit I/O Options Enabled Disabled Description This setting enables or disables 32 bit IDE data transfers. Chapter Four - 29 BIOS Setup Advanced Menu Phoenix SecureCore (tm) Setup Utility Advanced Security Boot Main Boot-time Diagnostic Screen: [Enabled] QuickBoot Mode: [Enabled] IGD - Boot Type: [VBT Default] PS/2 Mouse [Auto Detect] PCI Express Port #1 [Enabled] Device 29 USB 2.0 Enable: [Enabled] Passive Cooling Trip Point: [87 C] Core Multi-Processing: [Enabled] Intel(R) SpeedStep (tm) [Enabled] CX States [Enabled] PCI Hot-Plug Resources [Enabled] ► SIO SMC227 CONFIGURATION F1 Help Esc Exit ↑↓ Select ↔ Menu Item –/+ Enter Exit Item Specific Help Display the diagnostic screen during boot Change Values Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Warning Incorrect settings may cause system malfunction. To correct it, restore the Setup Default with . Chapter Four - 30 BIOS Setup Advanced Menu Selections You can make the following selections on the Advanced Menu. Feature Options Boot-time Diagnostic Screen QuickBoot Mode Enable Disabled Enable Disabled IGD - Boot Type VBT Default CRT LFP CRT+LFP EFP CRT+EFP Auto Detect Disabled Enabled PS/2 Mouse PCI Express Port #1 Enabled Auto Disabled Device 29 USB 2.0 Enable Passive Cooling Trip Point Enable Disabled 15 C/23 C/31 C/39 C/ 47 C/55 C/63 C/71 C/ 79 C/87 C/95 C/103 C/ 109 C/111C Disabled Core Multi-Processing Enable Disabled Description Display the diagnostic screen during boot Allows the system to skip certain tests while booting. This will decrease the time needed to boot the system. Select the Video Device that will be activated during POST “Disabled” prevents any installed PS/2 mouse from functioning, but frees up IRQ 12. “Enabled” forces the PS/2 mouse port to be enabled regardless if a mouse is present. “Auto Detect” will enable the PS/2 mouse only if present. “OS Controlled” only displayed if the OS controls the mouse. Disabled – Port always disabled. (If Port #1 is disabled), then the rest of the Ports will also be disabled.) Enabled – Port always enabled. Auto – Only enable if card found. Enables Device 29 USB 2.0 functionality. This value controls the temperature of the ACPI Passive Trip Point – the point in which the OS will begin throttling the CPU. Note: When the DTS is enabled, only values below 97C are valid. Determines whether the 2nd core is enabled. Disabled = 2nd core is disabled. Enabled = 2nd core is enabled. Chapter Four - 31 BIOS Setup Feature Intel(R) SpeedStep (tm) CX States Options Enable Disabled Enabled Disabled SIO SMC227 CONFGURATION Description Allows more than two freq. range to be supported Enable CPU C-states: Main switch for C0, C1, C2, C3, C4, Deep C4, C6 These items control the configuration of various National 393 SIO devices. Warning Make sure internal COMx mode settings must be with the same type of the external connected devices. Otherwise it may cause serial components damage in either side. Chapter Four - 32 BIOS Setup SIO SMC27 CONFIGURATION Sub-Menu Phoenix SecureCore (tm) Setup Utility Advanced SIO SMC227 CONFIGURATION [3F8-IRQ 4] [COM1] [2F8-IRQ 3] [COM2] [3E8-IRQ 10] [COM3] [2E8-IRQ 5] [COM4] [378-IRQ 3] [Standard] [Disabled] COM1 port: COM1 mode: COM2 port: COM2 mode: COM3 port: COM3 mode: COM4 port: COM4 mode: Printer1: Printer1 mode: Printer2: F1 Help Esc Exit ↑↓ Select ↔ Menu Item Specific Help Item –/+ Enter Configure COM1 using device options: [Disabled] No configuration [3F8-IRQ 4] Set the base I/O address for COM1 Change Values Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit SIO SMC27 CONFIGURATION Sub-Menu Selections You can make the following CONFIGURATION Sub-Menu. Feature Options COM1 port 3F8-IRQ 4 Disabled COM1 mode COM1 TTL1 COM2 port 2F8-IRQ 3 Disabled COM2 mode COM2 selections on the SIO SMC27 Description Configure COM1 using device options: [Disabled] No configuration [3F8-IRQ 4] Set the base I/O address for COM1 Configure UART mode options: [COM1]: External Device [TTL1]: Internal Device Configure COM2 using device options: [Disabled] No configuration [2F8-IRQ 3] Set the base I/O address for COM2 Configure UART mode options: Chapter Four - 33 BIOS Setup Feature Options TTL2 COM3 port 3E8-IRQ 10 Disabled COM3 mode COM3 TTL3 COM4 port 2E8-IRQ 5 Disabled COM4 mode COM4 TTL4 Printer1 378-IRQ 7 Disabled Printer1 mode Standard ECP EPP Printer2 Disabled 3BC Description [COM2]: External Device [TTL2]: Internal Device Configure COM3 using device options: [Disabled] No configuration [3E8-IRQ 10] Set the base I/O address for COM3 Configure UART mode options: [COM3]: External Device [TTL3]: Internal Device Configure COM4 using device options: [Disabled] No configuration [2E8-IRQ 5] Set the base I/O address for COM4 Configure UART mode options: [COM4]: External Device [TTL4]: Internal Device Configure Printer1 device options: [Disabled] No configuration [378-IRQ 7] Set the base I/O address for Printer1 Configure Printer1 mode options: Standard EPP ECP Configure Printer2 device options: [Disabled] No configuration [3BC] Set the base I/O address for Printer2 Chapter Four - 34 BIOS Setup Security Menu Warning If you forget user/supervisor password, the computer has to send back to manufacturer and replace Flash ROM to make it work again. Main Phoenix SecureCore (tm) Setup Utility Advanced Security Boot Supervisor Password Is: User Password Is: Clear Clear Set Supervisor Password Set User Password [Enter] [Enter] Diskette access: Fixed disk boot sector: [Normal] Password on boot: [Supervisor] AC97 Audio Interface: Cardbus/1394 Interface ►RF Interface Control [Auto] [Auto] F1 Help Esc Exit ↑↓ Select ↔ Menu Item Exit Item Specific Help Supervisor Password controls access to the setup utility. [Disabled] –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Note: ¾ Once you enter the incorrect password for three times, “System Disabled” will show on the screen. Please press the power switch for more than 5 seconds to shut down the computer. After shutting down, you are able to restart the system to enter the password again, Chapter Four - 35 BIOS Setup Security Menu Selections You can make the following selections on the Security Menu. Feature Set Supervisor Password Enter Description Supervisor Password controls access to the setup utility. Fixed disk boot sector Normal Write Protect Write protects the boot sector on the hard disk to protect against viruses. AC97 Audio Interface Auto Disabled Enabled Auto Disabled Enabled Control Detection of the AC97 Device. Cardbus/1394 Interface Options Cardbus Device Function Disable/ Enable USB Interface Control These items control various ICH USB Devices. PCIe Interface Control These items control various ICH PCI Express Devices. RF Interface Control RF Security Control: Wireless LAN WWAN GPS BlueTooth Chapter Four - 36 BIOS Setup RF Interface Control Sub-Menu Phoenix SecureCore (tm) Setup Utility Security RF Interface Control [Disabled] [Disabled] [Disabled] [Disabled] Wireless LAN: WWAN: GPS: BlueTooth: F1 Help Esc Exit Item Specific Help ↑↓ Select ↔ Menu Item –/+ Change Values Enter Select ► Sub-Menu Wireless LAN Control F9 F10 Setup Defaults Save and Exit RF Interface Control Sub-Menu Selections You can make the following selections on the RF Interface Control Sub-Menu. Feature Wireless LAN Options Enabled Disabled Description Wireless LAN Control WWAN Enabled Disabled WWAN Control GPS Enabled Disabled Enabled Disabled GPS Control BlueTooth BlueTooth Control Chapter Four - 37 BIOS Setup Boot Menu Main Phoenix SecureCore (tm) Setup Utility Advanced Security Boot Boot priority order: 1: USB FDC: 2: IDE CD: 3: USB KEY: 4: IDE HDD: FUJITSU MHW2040BH – (PM) 5: Legacy Network Card 6: PCI BEV: IBA GE Slot 00C8 v1322 7: 8: Excluded from boot order: : USB HDD: : USB CDROM: : USB ZIP: : USB LS120: : PCI SCSI: : Other USB: : PCI: : Legacy :1394 CDROM F1 Help Esc Exit ↑↓ Select ↔ Menu Item Exit Item Specific Help Keys used to view or configure devices: Up and Down arrows select a device. <+> and <–> moves the device up or down. and specifies the device fixed or removable. exclude or include the device to boot. enables or disables a device. <1 – 4> Loads default boot sequence. –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit The system will try to boot from device on top then the 2nd and so on. If there is more than one device in each category, only the device on top of sub-menu can boot up. Chapter Four - 38 BIOS Setup Exit Menu Main Phoenix SecureCore (tm) Setup Utility Advance Security Boot Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help Esc Exit ↑↓ Select ↔ Menu Exit Exit System Setup and save your changes to CMOS. Item –/+ Change Values Enter Select ► Sub-Menu F9 F10 Setup Defaults Save and Exit Exit Menu Selections You can make the following selections on the Exit Menu. Feature Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes Options Description Exit System Setup and save your changes to CMOS. Exit utility without saving Setup data to CMOS. Load default values for all SETUP items. Load previous values from CMOS for all SETUP items. Save Setup Data to CMOS Chapter Four - 39 Specification Chapter Five- Specification CPU Intel® Core™ Duo Processor (Penryn) T9400 2.26 GHz CPU runs at multiple speeds depending on the CPU type and operating system. Also, CPU speed switches automatically by detecting AC adapter/ battery operation and busy state. Memory System memory: Cache memory: Graphic memory: Standard: 1GB Expandable: 8GB Internal Level 3 MB Shared system memory from 32M to 1695 MB Chipset North Bridge: Mobile Intel® GM45 Express chipset Cantiga (G) MCH South Bridge: Intel® ICH9M-Enhanced Display Type: Resolution: Mode: Color: Brightness: 13.3” Active TFT Color 1024 x 768 pixels XGA 18 bit, 256K colors 384~480nits Chapter Five - 40 Specification Keyboard Number of keys: Key travel: 87 Keys (standard 87-key w/o backlight) 89 keys (optional rubber 89-key with backlight) 2.8 mm (standard 87-key w/o backlight) 1.5 mm (optional rubber 89-key with backlight) Touchpad Type: Compatible: Lifetime: Resistive type PS/2 Over 5,000,000 strokes lifetime Hard Disk Drive Type: Height: Interface: 2.5” (Removable) 9.5mm SATA DVD Super Multi Drive Type: Height: Interface: 5.25” (Removable) 12.7mm SATA Chapter Five - 41 Specification I/O Ports PS/2 x1 (KB + mouse) USB 2.0 x 3 IEEE1394 Fire Wire x 1 LAN RJ45 x 1 Optional: Modem RJ11 Port x 1 PCMCIA type I/II x 1;Express card (PCI-e) x 1 Optional: PCMCIA Type I/II x 2 Audio Jack x 3 (Mic/Line in/Earphone) DB9 x 2 (COM1/2) Optional: DB9 x 2 (COM3/4) Printer DB25 x 1 Docking Conn. x 1 (Optional: Military type) RGB DB15 x 1 Optional: Military Connector Port AC Adapter AC Input: Frequency: DC Output: Maximum Power: Dimension: Weight: 100 - 240 V 50/60 Hz 19V 90 Watts Max. Output 130mm (W) x 60mm (D) x 34mm (H) 430 g (0.9 lb.) Chapter Five - 42 Specification Battery Primary Battery: Type: Capacity: Dimension: Weight: 9 x 18650 cells Lithium Ion 11.1V 7200mAH 103 mm (W) x 73 mm (D) x 38 mm (H) 435 g 2nd Battery (Optional): Type: 9 x 18650 cells Lithium Ion Capacity: 11.1V 7200mAH Dimension: 150 mm(W) x 90 mm(D) x 20 mm(H) Weight: 560 g System Unit Dimensions and Weight Width: Depth: Height: Weight: 312 mm 246 mm 66.7 mm 4.3Kg Note: ¾ Weight varies depending on system configurations. Chapter Five - 43 Specification Materials and Recycling Materials of the computer are as follows: z Cabinet: Aluminum Alloy ADC-12, Magnesium Alloy AZ91D, UL grade PC+ABS GE C6200 or TN-3813BW z Bracket: Aluminum 5052, Steel with Nickel Plating, or Stainless Steel S304 z Cushion pad: Silicon Rubber, TPE z PCB: FR-4, UL 94V0 z Battery: Rechargeable Lithium Ion, 9 Cells per Pack z Packing: Carton- Unbleached Paper Cushion- Recyclable EPE Carrying bag- Recyclable PE Fiber User Guide- Recycled/Recyclable Paper Please recycle the parts according to the local regulations. Environmental Temperature: Humidity: Altitude: -20 ~ +50ºC (-4 ~ +122ºF) operating -40 ~ +70ºC (-40 ~ +158ºF) storage 5~95% Non-condensing operating 95% maximum storage 0 ~ 4,572 meters (0 ~ 15,000 feet) Chapter Five - 44 Optional Devices Chapter Six- Optional Devices Memory Card The memory card will expand your memory to facilitate better system performance. 1GB, 2GB, and 4GB SO-DIMM DDR3 memory cards are acceptable: Vehicle Adapter Input Voltage: Input Current: Output Voltage: Output Current: Wiring: Application: 12~32V 9A max 19V 4A Cigarette lighter/ Truck battery Car or Truck installation 2nd Battery A Lithium Ion rechargeable 2nd battery may install into the DVD Super Multi Drive-compartment. It shares the same capacity of primary battery and smart battery compliance. The computer’s internal charger can detect 2nd battery and perform charging accordingly. 2nd HDD Swappable with ODD, set as SATA primary slave drive. Chapter Six - 45 Optional Devices ODD (Optical Disk Drive) Swappable ODD for disks playing Compatible with VCD-ROM, DVD-ROM, and etc. Heater RT9 provides a heater kit for enabling the unit to work under the low temperature, the heater will first heat the HDD up to the temperature set by the user, and the system will boot after then. Also, the heater will keep monitoring the temperature of the HDD. Once the temperature becomes lower, the heater will heat up again to maintain the temperature set by the user. LAN and Modem Card 10Mb/100Mb/1Gb LAN Card 56Kbps V.92 Modem Card Wireless LAN Card IEEE 802.11 a/b/g/n wireless LAN card Bluetooth USB interface, Bluetooth® v2.1 + EDR system is backward compatible with v1.1/1.2/2.0 devices. WWAN USB interface, HSDPA/UMTS 3.5G Chapter Six - 46 Optional Devices GPS USB interface, Ublox LEA-5H KB Dust Cover KB Dust Cover is available for standard Keyboard. PCMCIA Cover Besides the attached PCMCIA rubber cover, there is an optional cover with a metal frame that can be fixed by using screws. The cover provides protection from dust or water for cabled PCMCIA cards. Users may seal the cable outlet after installation. Built-in Vehicle Adapter Converting power from car lighters or truck batteries to DC +19V, they are the same output ratings as AC adapters. It can power the system and charge the batteries simultaneously. Caution Remove or disconnect the adapter when leaving the vehicle to avoid battery exhaustion. Chapter Six - 47 Optional Devices Dual-Bay Battery Charger This charger provides two bays for the Primary and Secondary Batteries respectively. It accepts power from AC adapter or vehicle adapter and charged batteries. It takes approximately 6 hours to fully charge both batteries. COM 3/4 Card and Additional Serial Ports Supporting RS232, TTL, RS422, and RS485 formats. Military Connector/ Military Serial Connector Military connectors x 2 are available. 37-pin MIL-DTL-38999 military serial connector carrying max. 4 COM port signals is available. DockUnder RT8/9 Supporting Ports: DB9 x 2, USB 2.0 x 2, DVI x 1, PS/2 x 1, (KB with Mouse), RGB x 1, LAN RJ45 10M/100M, Antenna Hole (Reserved for Wireless Signals) Supporting Slots: PCI Slot x 1, PCIe Slot x 1 DC Input: 12~32V DC Power: 5V/ 2.5A, 3.3V/2.5A, ±12V/500mA Fan: Optional Dimensions: 302mm x 281mm x 109mm Weight: 4.8 kg Chapter Six - 48 Utilities & Drivers Chapter Seven- Utilities and Drivers The Utility DVD includes all the drivers for the installed devices in your notebook computer. Please consult the dealer if there is any driver missing. Also, through Device Manager in Windows, you are able to perform “Driver Update” or check if there are still drivers for the devices needed to be installed. Check readme.txt file on utility DVD to get the newest information before starting to install drivers. Note: ¾ Most device drivers are available in Windows. ¾ The Utility DVD includes most drivers of the computer’s installed devices. Consult dealer if any driver is missing. ¾ Re-install drivers or perform “Driver Update” to replace the Windows default drivers. ¾ Check readme.txt file on Utility DVD to get the newest information before starting to install drivers. Chapter Seven - 49 Utilities & Drivers Chipset Driver Windows 7/Enterprise 64-bit Drivers Installation: The Windows 7/Enterprise 64-bit will automatically install the driver. Graphic Controller RF9 supports Intel® GM45 giving you a flexible, programmable architecture that supports 2D, 3D and advanced 3D graphics, high-definition video decode, and image processing. Please follow the installation as below to use well with Intel® GM45. Insert the Utility DVD into the ODD. Click "setup.exe" in the directory of "RX9\Drivers\Win7(64bit)\VGA", and then follow prompt to complete driver installation. Windows may recommend using their driver, but you should confirm to change the factory bundled driver. Audio RF9 provides a high-quality audio sound effect for user to enjoy better sound quality. To activate this function, please follow the installation as below. Insert the Utility DVD into the ODD. Click"Vista_R221.exe" in the directory of "RX9\Drivers\Win7(64bit)\Audio", and then follow the prompt to complete installation. Mini PCI-E 1G RTL8111B LAN Driver The Windows 7/Enterprise 64-bit will automatically install the driver. Chapter Seven - 50 Utilities & Drivers Mini PCI INT8100 LAN Driver The Windows 7/Enterprise 64-bit will automatically install the driver. Modem Driver (Optional) The Windows 7/ Enterprise 64-bit will automatically install the driver. Touch Panel (Optional) There is a high sensitive touch panel for RF9 to be equipped with. Please follow the installation as below. Enter BIOS Setup screen and set COM1 port as “TTL1”. (COM1 has multiple connectivity, so it’s necessary to setup. The optional COM4 may be configured as touch screen and doesn’t need to configure the BIOS.) Afterwards, please cancel the prompt of installation wizard to setup the driver from the Utility DVD “RX9\Drivers\Win7(64bit)\PenMount Universal Driver v2.1.0.263\setup.exe), and follow the prompt to complete installation and then restart. Wireless LAN Driver (TBD) (Optional) Bluetooth Driver (TBD) (Optional) GPS Driver (TBD) (Optional) WWAN Driver (TBD) (Optional) Chapter Seven - 51 Utilities & Drivers Wireless Manager Wireless Manager is an exclusive utility designed and developed for the Wireless Devices of your notebook computer. Through Wireless Manager, turning the power ON or OFF become more convenient for being one of the power-saving tips. Read from the Utility DVD. Click Setup.exe in the directory of RX9\Utilities\Win7(64bit)Wirelessmanager then follow the prompt to complete installation. Chapter Seven - 52 Maintenance & Service Chapter Eight– Maintenance and Service Cleaning ALWAYS turn OFF the power, unplug the power cord and remove the battery before cleaning. The exterior of the system and display may be wiped with a clean, soft, and lint-free cloth. If there is difficulty removing dirt, apply non-ammonia, non-alcohol based glass cleaner to the cloth and wipe. An air gun is recommended for cleaning water and dust. For salty water please clean with fresh water then blow-dry with an air gun. Be sure not to turn the computer up side down while there is water being applied. Troubleshooting Should the computer fail to function properly, the troubleshooting steps below may be followed. Check AC/vehicle adapter, battery, and the power source. Minimize the configuration, i.e. remove extra peripherals and devices. Remove the modules one by one (HDD, CD-ROM, Battery, etc.). Remove the software suspected. Set BIOS fail-safe default. Re-install operating system and application software. Chapter Eight - 53 Maintenance & Service RMA Service If troubleshooting steps are unsuccessful, consult your dealer for RMA. Shipping instructions: 1. Remove any personal disks or other media. 2. Use the original shipping container and packing materials, if possible. 3. If the original packing materials are not available, wrap the equipment with soft material (e.g. PU/PE form) then put the wrapped equipment into a hard cardboard shipping box. 4. Include a sheet with the following information: (Note: Please keep a copy of this sheet for your records) Name Address Unit serial number Place and date of purchase or the original invoice number Date of failure A DETAILED Description of the problems you have encountered A list of the hardware/software configuration, if applicable. 5. Clearly mark the outside of the shipping box with the RMA #. If RMA # is not present on the shipping box, receiving will be unable to identify it and it might be returned. 6. Unless prior arrangements have been made, the customer is responsible for all shipping costs. Unauthorized use of the company’s shipping accounts is not permitted. Chapter Eight - 54 Recycled/ Recyclable Printed in Taiwan G630902000
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2010:07:20 13:32:08+08:00 Create Date : 2010:07:20 13:31:16+08:00 Metadata Date : 2010:07:20 13:32:08+08:00 Format : application/pdf Title : Microsoft Word - UM.doc Creator : Administrator Document ID : uuid:41faf240-db4a-4afc-8866-6e1e8cdf7c41 Instance ID : uuid:81b7e7c8-9361-4c99-8f1d-de67927c1a46 Page Count : 65 Author : AdministratorEXIF Metadata provided by EXIF.tools