Mitsumi Electric Co DWMW015 Wireless LAN Module User Manual Manual User

Download:
Mirror Download [FCC.gov]
Document ID	1234288
Application ID	fjwqsH8cEFvTs75OVS086g==
Document Description	Manual User
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.38kB (17220 bits)
Date Submitted	2010-01-28 00:00:00
Date Available	2010-06-30 00:00:00
Creation Date	2008-09-25 08:44:11
Producing Software	JUST PDF Driver
Document Lastmod	2008-09-25 08:44:13
Document Title	Microsoft Word - User_Manual_DWM-W015_r0_0_080924.doc
Document Creator	Microsoft Word - User_Manual_DWM-W015_r0_0_080924.doc
Document Author:	560058

User Manual
MITSUMI WiFi Module
MODEL DWM-W015
The purpose of this manual is to explain correct way how to integrate module DWM-W015 to the
end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual
presents information that shows how module and OEM product, where module integrated, complies
with regulations in certain regions. Any modifications, not expressly approved by the manufacturer
could void the authority to operate in these regions.
The MITSUMI WiFi Module, model DWM-W015 has to be installed and used in accordance with the
technical description/installation instructions provided by the manufacturer.
For detail information concerning type approval of this module (e.g. where this module is already
pre-approved) please contact the authorized local distributor or the manufacturer.
The system may only be implemented in the configuration that was authorized. Note that any
changes or modifications to this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
Regulatory Information
Operational Information
Wireless Interoperability
The end product integrating this module is designed to be interoperable with any wireless LAN
product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency
division multiplexing (OFDM) radio technology and to comply with the following standards.
・IEEE Std 802.11b Standard on 2.4GHz Wireless LAN
・IEEE Std 802.11g Standard on 2.4GHz Wireless LAN
・IEEE Std 802.11 Standard on 2.4GHz Wireless LAN
Safety
The end product integrating this module, like other radio devices, emits radio frequency
electromagnetic energy. The level of energy emitted by this device, however, is less than the
electromagnetic energy emitted by other wireless devices such as mobile phones. The end product
integrating this module operates within the guidelines found in radio frequency safety standards and
recommendations. These standards and recommendations reflect the consensus of the scientific
community and result from deliberations of panels and committees of scientists who continually
review and interpret the extensive research literature. In some situations or environments, the use of
the end product integrating this module may be restricted by the proprietor of the building or
responsible representatives of the applicable organization. Examples of such situations include the
following:
・Using the end product integrating this module onboard airplanes, or
・Using the end product integrating this module in any other environment where the risk of
interference with other devices or services is perceived or identified as being harmful.
If uncertain of the policy that applies to the use of wireless devices in a specific organization or
environment (an airplane, for example), ask for authorization to use the end product integrated into
this module before turning it on.
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by tuning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Labeling
MITSUMI WiFi module DWM-W015 labeled as below.
FCC ID: EW4DWMW015
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when
the module is installed into the system, “Contains FCC ID: EW4DWMW015” shall be placed on the
outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Canada-Industry Canada (IC)
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of this device.
L ‘ utilization de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le fomctionnement du dispositif.
The term “IC” before the equipment certification number only signifies that the Industry Canada
technical specifications were met.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropic radiated power (EIRP) is not more than that required for
successful communication.
To prevent radio interference to the licensed service, this device is intended to be operated indoors
and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is
installed outdoors is subject to licensing.
Pour empecher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit
etre utilize a l’interieur et devrait etre place loin des fenetres afinde Fournier un ecram de blindage
maximal. Si le matriel (ou son antenne d’emission) est installe a l’exterieur, il doit faire l’objet d’une
licence.
Caution: Exposure to Radio Frequency Radiation.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it
does not emit RF field in excess of Health Canada limits for the general population; consult Safety
Code 6, obtainable from Health Canada’s website at www.hc-sc.gc.ca/rpb.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Creator                         : Microsoft Word - User_Manual_DWM-W015_r0_0_080924.doc
Producer                        : JUST PDF Driver
Create Date                     : 2008:09:25 08:44:11+09:00
Modify Date                     : 2008:09:25 08:44:13-15:00
Author                          : 560058
Title                           : Microsoft Word - User_Manual_DWM-W015_r0_0_080924.doc
Page Count                      : 4
Page Mode                       : UseNone

EXIF Metadata provided by EXIF.tools