Mitsumi Electric Co DWMW028 Wireless LAN module User Manual Module Users Manual

Download:
Mirror Download [FCC.gov]
Document ID	1367236
Application ID	7/ZaSziHQwwCwBpW6EyGdw==
Document Description	Module Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.35kB (79413 bits)
Date Submitted	2010-10-28 00:00:00
Date Available	2011-05-03 00:00:00
Creation Date	2010-10-21 13:15:16
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2010-10-21 13:15:16
Document Title	Microsoft Word - User Manual MITSUMI WiFi Module MODE DWM-W028_20101020.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	N2458

User Manual
MITSUMI WiFi Module MODEL
DWM-W028
The purpose of this manual is to explain correct way how to integrate module DWM-W028
to the end product. It includes procedures that shall assist you to avoid unforeseen
problems. This manual presents information that shows how module and OEM product,
where module integrated, complies with regulations in certain regions. Any modifications,
not expressly approved by the manufacturer could void the authority to operate in these
regions.
The MITSUMI WiFi Module, model DWM-W028 has to be installed and used in accordance
with the technical description/installation instructions provided by the manufacturer.
For detail information concerning type approval of this module (e.g. where this module is
already pre-approved) please contact the authorized local distributor or the manufacturer.
The system may only be implemented in the configuration that was authorized. Note that
any changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
Regulatory Information
Operational Information
Wireless Interoperability
The end product integrating this module is designed to be interoperable with any wireless
LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal
frequency division multiplexing (OFDM) radio technology and to comply with the following
standards.
IEEE Std 802.11b Standard on 2.4GHz Wireless LAN
IEEE Std 802.11g Standard on 2.4GHz Wireless LAN
Safety
The end product integrating this module, like other radio devices, emits radio frequency
electromagnetic energy. The level of energy emitted by this device, however, is less than the
electromagnetic energy emitted by other wireless devices such as mobile phones. The end
product integrating this module operates within the guidelines found in radio frequency
safety standards and recommendations. These standards and recommendations reflect the
consensus of the scientific community and result from deliberations of panels and
committees of scientists who continually review and interpret the extensive research
literature. In some situations or environments, the use of the end product integrating this
module may be restricted by the proprietor of the building or responsible representatives of
the applicable organization. Examples of such situations include the following:
Using the end product integrating this module onboard airplanes, or
Using the end product integrating this module in any other environment where the
risk of interference with other devices or services is perceived or identified as being
harmful.
If uncertain of the policy that applies to the use of wireless devices in a specific organization
or environment (an airplane, for example), ask for authorization to use the end product
integrated into this module before turning it on.
USA-Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by tuning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
z Reorient or relocate the receiving antenna.
z Increase the distance between the equipment and the receiver.
z Connect the equipment to outlet on a circuit different from that to which the receiver is
connected.
z Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Labeling
MITSUMI WiFi module DWM-W028 labeled as below.
FCC ID: EW4DWMW028
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not
visible when the module is installed into the system, “Contains FCC ID: EW4DWMW028”
shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
Minimum 20cm safe separation distance warning required for the module which must
comply with RF exposure requirement.
Canada-Industry Canada (IC)
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of this device.
L ‘ utilization de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage adioélectrique reçu,
même si ce brouillage est susceptible de compromettre le fomctionnement du dispositif.
The term “IC” before the equipment certification number only signifies that the Industry
Canada technical specifications were met.
To reduce potential radio interference to other users, only the authorized antenna type and
its gain should be so chosen that the equivalent isotropic radiated power (EIRP) is not more
than that required for successful communication.
To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to licensing.
Pour empecher que cet appareil cause du brouillage au service faisant l’objet d’une licence,
il doit etre utilize a l’interieur et devrait etre place loin des fenetres afinde Fournier un
ecram de blindage maximal. Si le matriel (ou son antenne d’emission) est installe a
l’exterieur, il doit faire l’objet d’une licence.
Labeling
MITSUMI WiFi module DWM-W028 labeled as below.
IC: 4250A-DWMW028
The proposed with IC label format is to be placed on the module. If IC number is not visible
when the module is installed into the system, “Contains IC number: 4250A-DWMW028”
shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
Minimum 20cm safe separation distance warning required for the module which must
comply with RF exposure requirement.
The installer of this radio equipment must ensure that the antenna is located or pointed
such that it does not emit RF field in excess of Health Canada limits for the general
population; consult Safety Code 6, obtainable from Health Canada’s website at
www.hc-sc.gc.ca/rpb.
Antennas
According to RSS-Gen 7.1.4, if the detachable antenna DN57 2.4GHz SMA-PR is used with
the module DWMW028 for the hosts included PARTNER-CTR Debugger, PARTNER-CTR
Capture and PARTNER-CTR Capture Debugger, the following condition must be
considered:
This device has been designed to operate with the antennas listed below, and having a
maximum gain of 2.62dB. Antennas not included in this list or having a gain greater than
2.62dB are strictly prohibited for use with this device. The required antenna impedance is
50ohms.
Detachable antenna: DN57 2.4GHz SMA-PR
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that permitted for successful communication.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2010:10:21 13:15:16+09:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2010:10:21 13:15:16+09:00
Format                          : application/pdf
Title                           : Microsoft Word - User Manual MITSUMI  WiFi Module MODE DWM-W028_20101020.doc
Creator                         : N2458
Document ID                     : uuid:9ee4c404-3429-48a2-b92f-796889388200
Instance ID                     : uuid:b5f5a0a9-c466-4e2e-af79-6bb5d3fbd1e1
Page Count                      : 6
Author                          : N2458

EXIF Metadata provided by EXIF.tools