Mitsumi Electric WML-C68 Bluetooth Module User Manual

Mitsumi Electric Co., Ltd. Bluetooth Module

User Manual

Page 1 of 4 WML-C68_User_Manual 18. Jun. 2012 COMMERCIAL IN CONFIDENCE This material may not in whole or part be copied, stored electronically or communicated to third parties without MITSUMI ELECTRIC CO., LTD’s prior agreement in writing. WML- C68 User Manual The purpose of this manual is to explain correct way how to integrate module WML-68 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions. Any modifications, not expressly approved by the manufacturer could void the authority to operate in these regions. Content 1.General 2. European Community Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC 3. FCC Regulatory Information 4. Canada-Industry Canada (IC) 1. General This Bluetooth radio module has to be installed and used in accordance with the technical description/installation instructions provided by the manufacturer. This Bluetooth radio module is intended to be placed on the market in all States, where the Bluetooth™ technology and the used frequency band is released. For detail information concerning type approval of this module (e.g. where this module is already pre-approved) please contact the manufacturer. The system may only be implemented in the configuration that was authorized. Note that any changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
his material mawpean Comive 1999/TSUMI decnts and othement is marktes complianpecifications8, ElectromaData transmis; Harmonize9-17, Electroity (EMC) staHYPERLAN 1, Safety of Assessmengnetic fields (Exposure e must not beExposure evcal documen TSURUMAMI ELECTRNEERING DEODULE BUS81-42-310-5681-42-310-5ay not in whowithout MITSmmunity /5/EC clares that Tr relevant prked with the nce with the s: agnetic comssion equipmed EN coveromagnetic Candard for raEquipment. Information nt of electron(0 Hz-300 Gto Radio Fe co-locatedvaluation. ntation as reAKI, TAMA-SRIC CO.,LTDEPTMENT SINESS DIVI691 582 COMMEle or part be cSUMI ELECTDeclaratThe Mitsumirovisions of D symbR&TTE Direpatibility andment operatiring essentiaCompatibilityadio equipmTechnologynic and electGHz). Frequency d or operatinequired by thSHI, TOKYOD. ISION ERCIAL IN COcopied, stored TRIC CO., LT tion of Coi module WDirective 19bol and can ective 1999/d Radio speing in the 2,4al requiremey and Radio ment and sery Equipmenttrical equipmy Radiationng in conjunche ConformitO, 206-8567 ONFIDENCEelectronicallyTD’s prior agreonformityWML-C68 is 999/5/EC. be used thro/5/EC and mctrum Matte4 GHz ISM nts under arspectrum Mrvices; Part 1t. ment related n. ction with anty AssessmeJAPAN. E y or communiceement in wriy with Rein compliancoughout the meets the relers (ERM); Wband and usrticle 3.2 of tMatters (ERM17: Specific to human exny other anteent proceduWML-C68icated to third iting. egard to tce with the eEuropean clevant parts Wideband trasing wide bathe R&TTE DM); ElectromConditions fxposure resenna or transre is kept at Page 2 o8_User_Man18. Jun. 20parties the R&TTessential community.of following ansmission and modulatDirective agnetic for Widebanstrictions for smitter, withthe followinof 4 nual 012 TE tion nd out g
Page 3 of 4 WML-C68_User_Manual 18. Jun. 2012 COMMERCIAL IN CONFIDENCE This material may not in whole or part be copied, stored electronically or communicated to third parties without MITSUMI ELECTRIC CO., LTD’s prior agreement in writing. 3. FCC Regulatory Information Caution: Any changes or modifications not expressly approved by the party responsible for product compliance could void the user's authority to operate the equipment. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help Labelling MITSUMI Bluetooth module WML-C68 is labeled as below. FCC ID: POOWML-C68 If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: POOWML-C68” shall be placed on the outside of final host system.
Page 4 of 4 WML-C68_User_Manual 18. Jun. 2012 COMMERCIAL IN CONFIDENCE This material may not in whole or part be copied, stored electronically or communicated to third parties without MITSUMI ELECTRIC CO., LTD’s prior agreement in writing. 4. Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device. L ‘ utilization de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Labelling MITSUMI Bluetooth module WML-C68 is labeled as below. IC ID: 4250A-WMLC68 If IC ID is not visible when the module is installed into the system, “Contains IC ID: 4250A-WMLC68” shall be placed on the outside of final host system.

Navigation menu