Mobile Aspects IRISPRINT10 RFID Printer Module User Manual Product Requirements
Mobile Aspects Inc RFID Printer Module Product Requirements
User manual - Installation Instructions
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3330647 |
| Application ID | cbJgE4hc6DbGvb/pHfGUoQ== |
| Document Description | User manual - Installation Instructions |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | Yes |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 31.41kB (392648 bits) |
| Date Submitted | 2017-03-24 00:00:00 |
| Date Available | 2017-03-24 00:00:00 |
| Creation Date | 2017-02-27 13:42:34 |
| Producing Software | Microsoft® Word 2016 |
| Document Lastmod | 2017-02-27 13:42:34 |
| Document Title | Product Requirements Document |
| Document Creator | Microsoft® Word 2016 |
| Document Author: | tsriharto |
iRISPrint 1.0 Internal Installation Instructions Rev 0 3700 S. Water St Ste 310 Pittsburgh PA 15203 USA FCC Statement WARNING! This module is to be installed only in Mobile Aspects end products by Mobile Aspects personnel, and shall not be offered to 3rd party OEM integrators or the general public. Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The RF Module is labeled with its own FCC ID Number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: R4FIRISPRINT10 or Contains FCC ID: R4FIRISPRINT10 Mobile Aspects, 2017 Page 2 Table of Contents 1. INTRODUCTION............................................................................................................................................................................ 4 1.1 2. PURPOSE OF THE DOCUMENT ...................................................................................................................................................... 4 INSTALLATION INSTRUCTIONS .............................................................................................................................................. 4 2.1 2.2 2.3 PRINTER MAIN CONTROLLER ..................................................................................................................................................... 4 PRINTER ANTENNA ..................................................................................................................................................................... 5 CONSOLE TO PRINTER CONNECTION ........................................................................................................................................... 6 Mobile Aspects, 2017 Page 3 1. Introduction 1.1 Purpose of the document The purpose of this internal document is to provide work instructions on how to install the printer main controller and printer antenna inside a console and printer. 2. Installation Instructions 2.1 Printer Main Controller Printer main controller location inside the console 1) Motherboard 2) 3) Ribbon Cable With a hex driver, install the printer main controller using 6-32 button head screws. Connect the ribbon ribbon cable from the printer controller to the motherboard. Connect the 4-pin ATX cable from the power supply to the printer controller. Power Supply Printer Controller Mobile Aspects, 2017 Page 4 2.2 Printer Antenna 1) Install printer at this location inside the printer. 1) Attach the antenna cable at this this location in the back of the printer. Mobile Aspects, 2017 Page 5 2.3 Console to Printer Connection Connect the printer to the console as show below. RS232 Null Modem Cable SMA Coaxial Cable Mobile Aspects, 2017 Page 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 6 Language : en-US Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Microsoft® Word 2016 Title : Product Requirements Document Creator : tsriharto Description : Catheter Cabinet Creator Tool : Microsoft® Word 2016 Create Date : 2017:02:27 13:42:34-08:00 Modify Date : 2017:02:27 13:42:34-08:00 Document ID : uuid:E4B3BB95-D106-4E06-8CDE-27EBA263E9D7 Instance ID : uuid:E4B3BB95-D106-4E06-8CDE-27EBA263E9D7 Author : tsriharto Subject : Catheter CabinetEXIF Metadata provided by EXIF.tools