Mobility Sound Technology PTT-U Bluetooth PTT User Manual PTT U spec and manual

Mobility Sound Technology Ltd. Bluetooth PTT PTT U spec and manual

User manual

Download: Mobility Sound Technology PTT-U Bluetooth PTT User Manual PTT U spec and manual
Mirror Download [FCC.gov]Mobility Sound Technology PTT-U Bluetooth PTT User Manual PTT U spec and manual
Document ID3406410
Application IDRviKconcw/qz3wIORRr5XA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize198.87kB (2485895 bits)
Date Submitted2017-05-28 00:00:00
Date Available2017-05-28 00:00:00
Creation Date2017-05-23 17:51:36
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2017-05-23 17:51:36
Document TitleMicrosoft Word - PTT-U spec and manual
Document CreatorPScript5.dll Version 5.2.2
Document Author: kay

PTT‐U

PTT‐U1
•Bluetooth PTT button for iOS and Android
•Embedded power switch extends battery life.
•CR2032 battery provides at least 1 year battery
life
•Intended function: control your cell phone
through Bluetooth technology.

•Type: Bluetooth PTT button
•Operating Temp: ‐20℃±2℃ ~ 50℃±2℃
PTT‐U2
•Approx. Weight: 10g (PTT‐U1)
•Bluetooth version: Bluetooth V4.0 (BLE only)
•Battery: CR2032
•Battery life: at least 1 year
•Accessory:
a. None (PTT‐U1)
b. Vecro fastener strap (PTT‐U2)
c. Rubber ring (PTT‐U3)

•Zello iOS
PTT‐U3
2.5cm
1.7cm
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To
maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the
transmitting antenna during transmitting.
Notice : The changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority to operate the device.
Start paring PTT‐U1/U2/U3 with your smart phone
1. Power PTT‐U1/U2/U3
2. Start Bluetooth function on your smart phone
Pairing procedure for Zello iOS
Start Zello, go to options, tap Push‐To‐Talk button, tap Wireless Zello button, start Wireless button
service, find the device PTT‐Z and connect it.
Pairing procedure for WAVE iOS
Pairing procedure for WAVE Android
Start WAVE, go to settings, tap “App Settings”, tap and start“Use Bluetooth Device for PTT”, select
available device “PTT‐Z”, and then connect PTT‐Z.
Using EP31‐P12‐CEL or EP31‐P12N‐CEL with PTT‐UX
Mobility Sound releases 2 types acoustic tube earphone respectively for iPhone and Android phone. The
difference between these 2 solutions is the pickup phone button on the earphone. Both models are for POC
APP only.
EP31‐P12N‐CEL
No pick up button
EP31‐P12N‐CEL
With pick up button

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : kay
Create Date                     : 2017:05:23 17:51:36+08:00
Modify Date                     : 2017:05:23 17:51:36+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - PTT-U spec and manual
Creator                         : kay
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:db3ddef5-b356-40a5-9e5c-5ddba2741222
Instance ID                     : uuid:65188f03-b702-470e-a43d-caf57edecd99
Page Count                      : 6
EXIF Metadata provided by EXIF.tools
FCC ID Filing: XTS-PTT-U

Navigation menu