Mobix Wireless Solutions 400 Data Collection System User Manual MiniHub V1 3x

Mobix Wireless Solutions LTD Data Collection System MiniHub V1 3x

User Manual

Download: Mobix Wireless Solutions 400 Data Collection System User Manual MiniHub  V1 3x
Mirror Download [FCC.gov]Mobix Wireless Solutions 400 Data Collection System User Manual MiniHub  V1 3x
Document ID2189923
Application ID4bzD8MEzDPe28dEqQUawfQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize67.51kB (843889 bits)
Date Submitted2014-02-14 00:00:00
Date Available2014-02-19 00:00:00
Creation Date2014-02-10 16:26:28
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2014-02-10 16:26:28
Document TitleMicrosoft Word - MiniHub User Manual V1_3.docx
Document CreatorPScript5.dll Version 5.2
Document Author: ofir

n-DNet MiniHub
User Manual
Version 1.3
06-FEB-14
Table of Contents
1.
GENERAL DESCRIPTION.................................................................................................................... 3
2.
MINIHUB SPECIFICATIONS ............................................................................................................... 4
3.
CONNECTORS ................................................................................................................................... 5
4.
INSTALLATION ................................................................................................................................. 6
3.
INSTALLATION ................................................................................................................................. 8
4.
SAFETY ............................................................................................................................................. 9
5.
SUPPLY DISCONNECT SWITCH........................................................................................................ 10
5.
ENVIRONMENTAL CHARACTERISTICS ............................................................................................ 10
7.
MAINTENANCE .............................................................................................................................. 11
8.
DECLARATION OF CONFORMITY .................................................................................................... 12
APPENDIX 1 ........................................................................................................................................... 13
APPENDIX 2 ........................................................................................................................................... 14
Page 2
MiniHub User Guide
10/15/2013
1. General Description
The n-DNet™ MiniHub is a standalone network interface unit connecting endpoints to the Mobix
patented n-Dimensional Network (see box for n-DNet™ description) It is a feature rich MiniHub
designed to collect, store and forward data from up to 2 meters. Meters could be in any combination
of electric, gas and/or water with Pulse, RS-232 or RS-485. As a node on the patented n-Dimensional
mesh network, the n-DNet™ MiniHub communicates simultaneously in parallel over RF and PLC
there by guaranteeing continuous reliable two-way communications at the highest cost efficiency.
System tempering detection, parameter driven abnormal consumption and remote service
connect/disconnect are among the smart n-DNet™ MiniHub unique features.
Page 3
MiniHub User Guide
10/15/2013
2. MiniHub Specifications
The following tables list the Hub specifications:
Physical Specification:
Specification
Length
Width
Height
Value
121.85 mm
99.8 mm
35 mm
Electrical Specifications:
Specification
Input voltage
Input Frequency
Max Current
Value
110-230 VAC
50-60 HZ
20 mA
Environmental :
Specification
Operating temperature Range
RoHS standard
Value
-40°C to +70°C
Fully compliant
PLC Standards :
Specification
PLC standard
Value
Complies with FCC,ARIB and EN500651-CENELEC (EU) regulations
RF standard:
Specification
RF standard
Value
Complies with FCC, ETSI and ARIB Frequency
240–930 MHz
-118dBm
10dBm (complies with FCC)
Sensitivity
Max Output Power
Page 4
MiniHub User Guide
10/15/2013
Interfaces
Specification
Pulse/Alarm input port
Output port (for valve control)
Serial interface
AC switch control
Value
RS-232,RS-485
0-100ma/110-250VAC
LEDs
LED
LD1
LD2
LD3
LD4
LD5
LD6
LD7
Specification
SW LED
RF TX
PLC Function
PLC TX
RF RX
PLC RX
Valve capacitor ready
Color
Orange
Red
Green
Red
Green
Green
Green
Location on the board (top left side):
3. Connectors
AC Interface connector pin out
Pin
GND
Line SW
Page 5
MiniHub User Guide
Function
GND
AC switch output connection
10/15/2013
N
Neutral input
AC Line input
DC Interface connector pin out
Pin
GND
IN_2
IN_1
OUT_2
OUT_1
GND
TX
RX
Function
GND
Alarm input
Pulse input
Valve control (+)
Valve control (-)
GND
TX RS-232 / A RS-485
RX RS-232 / B RS-485
4. Installation
1. There are 2 options to mount the MiniHub:
• Mount on a DIN rail using the dedicated DIN mounting on the back of
the box.
• Using the mounting holes on the back of the box
See appendix 2
2. To prevent fire spreading in case of circuit faults, the Hub must be installed in a suitable fire
enclosure to the latest version of UL 61010-1, without any openings at the bottom.
Enclosure minimum size will be 300x250 mm.
3. Connect the 8 control wires to the bottom pitches according to the pin numbers. Use the
designated screws.
This is a view of the wire connections of the MiniHub:
4. According to the scheme of connection:
• Meter pulse wires (IN_1,IN_2,GND)
 The number indicates the meter’s number
 Each two meters have a joint ground connection
 Connect the (+) wire to the numbered input
 Connect the (-) wires to the joint GND connector
Page 6
MiniHub User Guide
10/15/2013
GND IN_2 IN_1 Out_2 Out_1 GND Tx
Rx
GND Line N
SW
5. Meter Pulse + Valve control (GND,IN_2,IN_1,Out_2,Out_1)
The output number indicates the controlled valve.
Out_2 – Connect the (+) wire of the valve control to the numbered output.
Out_1 – Connect the (-) wire of the valve control to the numbered output.
IN_2 – Connect the alarm wire of the Meter to the numbered input
IN_1 – Connect the (+) wire of the Meter to the numbered input
GND – Connect the ground wire of the Meter.
GND IN_2 IN_1 Out_2 Out_1 GND Tx
Rx
GND Line N
SW
6. Serial meter connection RS232/RS485
 Connect the meter wires to Tx, Rx and GND
Page 7
MiniHub User Guide
10/15/2013
7. Connect the power supply cable to a 230/110Vac power source.
3. Installation
1. Il ya 2 options pour monter le MiniHub:
• Montage sur un rail DIN à l'aide de la norme DIN dédié montage à l'arrière de la boîte.
• Utiliser les trous de montage à l'arrière de la boîte
2. Monter sur un rail DIN à l'aide de la DIN dédié sur le dos de la boîte.
3. Pour éviter la propagation du feu en cas de défauts du circuit, le moyeu doit être installé dans un
boîtier d'incendie adapté à la dernière version de la norme UL 61010-1, sans ouvertures au bas.
4. Connecter les fils de commande 8 pour les emplacements de fond selon l'une des numéros de
broche. Utilisez les vis désignées.
Il s'agit d'un point de vue des connexions du MiniHub:
5. Selon le schéma de connexion:
•
Page 8
Mètre d'impulsion fils (IN_1, IN_2, GND)
 fils de compteurs de sortie d'impulsions (IN_1,IN_2,GND)
 Le nombre indique le numéro du compteur
 Tous les deux mètres ont une connexion de masse commune
 Connecter le fil (+) à l'entrée numérotés
 Connecter le fil (-) à la commune connecteur GND
MiniHub User Guide
10/15/2013
GND IN_2 IN_1 Out_2 Out_1 GND Tx
Rx
GND Line N
SW
6. Mètre d'impulsions + Soupape de commande (GND,IN_2,IN_1,Out_2,Out_1)
 Le nombre de sortie indique la soupape commandée.
 Out_2 – Connecter le fil (+) de la soupape de commande à la sortie numérotée.
 Out_1 – Connecter le fil (-) de la commande de la vanne à la sortie numérotées.
 IN_2 – Connecter le fil d'alarme du Mètre à l'entrée numérotés.
 IN_1 – Connecter le fil (+) du mètre à l'entrée numérotés
 GND – Connecter le fil de terre du mètre
GND IN_2 IN_1 Out_2 Out_1 GND Tx
Rx
GND Line N
SW
4. Safety
•
•
•
•
•
Page 9
Connect the input and output wires only when mains are not connected
To prevent fire spreading in case of shortcut, the hub must be installed in a suitable
enclosure without any openings at the bottom.
Connect mains only to 110-230Vac power source
All AC connections should be done by an authorized electrician
The unit intends to be powered from building wiring in Overvoltage Category II. If
the unit is installed in Overvoltage Category higher than II, external overvoltage
MiniHub User Guide
10/15/2013
protective device compliant with IEC 61643 standard and NEC/CEC shall beprovided
in building installation to reduce mains transients to Overvoltage Category II.
Sûreté
•
•
•
•
•
Connectez les fils de l'entrée et sortie seulement quand les principale source
d'électricité ne sont pas connectés
Pour éviter la propagation du feu en cas de raccourci, le moyeu doit être installé
dans une enceinte appropriée sans ouvertures au bas.
Raccorder seulement aux source d'alimentation 110-230V
Toutes les connexions AC doit être effectuée par un électricien agréé
l'unité est destiné à être alimenté à partir de l'installation électrique dans les
catégorie de surtension 2. Si l'unité est installée dans la catégorie de surtension
supérieure à 2, externe conforme surtension dispositif de protection avec la IEC
61643 standard et NEC / CEC doivent être fournis dans la construction de
l'installation pour réduire les transitoires conduites à la catégorie de surtension 2.
5. Supply disconnect switch
A supply disconnect switch, or a circuit breaker must be installed at the connection point of the
power cable to the mains. Circuit breaker should be a standard device with the following
characteristics - 2A 110/230VAC 50/60Hz. An example - S201M-C4NA by ABB. The switch should
be in close proximity to the hub within easy reach for the operator. A marking should be added on
the switch identifying it as a disconnection device for the hub.
Fourniture Sectionneur
Un sectionneur d'alimentation, ou un disjoncteur doit être installé au point de connexion du câble
d'alimentation sur le secteur. Disjoncteur doit être un dispositif standard avec les caractéristiques
suivantes - 2A 110/230VAC 50/60Hz. Un exemple - S201M-C4NA par ABB. Le commutateur doit se
trouver à proximité du concentrateur à la portée de l'opérateur. Un marquage doit être ajouté sur
l'interrupteur de l'identifier comme un dispositif de déconnexion pour le concentrateur.
5. Environmental characteristics
•
•
•
•
•
Page 10
The Hub is intended for indoor use only. For outdoor application a weatherproof external
enclosure should be added.
Installation site altitude will be up to 2000m.
Temperature range should be -40- +70 deg C. For harsher temperatures an external
temperature controlled enclosure should be added.
Maximum relative humidity 80% for temperatures up to 31 deg C decreasing linearly to
50% relative humidity at 40 deg C.
Mains supply voltage fluctuations up to +-10% of the nominal voltage.
MiniHub User Guide
10/15/2013
•
•
Overvoltage category II
Pollution Degree 2
Caractéristiques de l'environnement
•
•
•
•
•
Le concentrateur est destiné à une utilisation en intérieur. Pour l'application extérieure
d'une enceinte étanche externe doit être ajouté.
altitude du site d'installation sera à 2000m.
Plage de température devrait être de -40 à +70 ° C. Pour des températures plus sévères une
température extérieure contrôlée enceinte doit être ajoutée.
Humidité relative maximale 80% pour des températures jusqu'à 31 ° C diminuant
linéairement jusqu'à une humidité relative de 50% à 40 degrés C.
Alimentation des fluctuations de tension à + -10% de la tension nominale.
Catégorie de surtension II
Degré de pollution • 2
7. Maintenance
WARNING: RISK OF ELECTRIC SHOCK
Do not touch live electrical parts.
• Verify that the system is properly installed and grounded according to its installation
manual and national, state, and local codes.
• Incorrect connections may cause electric shock.
• Disconnect input power before installing or servicing the equipment.
WARNING: No user-serviceable parts inside
If any component part is found to be damaged and/or in need of service, have all such
service performed by a certified electrical contractor or qualified Mobix personnel.
AVERTISSEMENT: RISQUE DE CHOC ÉLECTRIQUE
•
Ne toucher pas les pièces électriques.
• Vérifiez que le système est correctement installé et mis à la terre conformément à son
manuel d'installation et les codes fédéral, l'Etat, et local.
• Les connexions incorrectes peuvent causer un choc électrique.
• Débranchez la puissance d'entrée avant d'installer ou de réparer l'équipement.
AVERTISSEMENT: Pas de pièces réparables par l'utilisateur à l'intérieur
• Si une pièce composante se trouve à être endommagé et / ou dans le besoin de service, ont
tous effectué un service téléphonique par un électricien agréé ou du personnel qualifié de
Mobix.Alpha
Keep the Hub clean
Page 11
MiniHub User Guide
10/15/2013
•
Regularly check for and remove foreign objects or debris on or around your Hub.
Check cords
• If operating, disconnect the Hub from the power source.
• Inspect the Hub supply cord – look for nicks in the insulation or excessive rubs on the cord.
8. Declaration of Conformity
Manufacturer’s Name: Mobix
Declares under our sole responsibility that the products:
Product Names: MiniHub H400
Conform(s) to the following standard(s) or other normative document(s):
EMC: FCC Part 15B class B
Radio: FCC 15C.249
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• The device may not cause harmful interference
• This device must accept any interference received, including interference that may cause undesired
operation.
Modifications: Changes or modifications to this equipment not expressly approved by Mobix may
void the user’s authority to operate this equipment.
Page 12
MiniHub User Guide
10/15/2013
Appendix 1
MiniHub external box
Page 13
MiniHub User Guide
10/15/2013
Appendix 2
MiniHub installation points
Page 14
MiniHub User Guide
10/15/2013

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 14
Producer                        : GPL Ghostscript 8.64
Create Date                     : 2014:02:10 16:26:28+02:00
Modify Date                     : 2014:02:10 16:26:28+02:00
Title                           : Microsoft Word - MiniHub User Manual V1_3.docx
Creator                         : PScript5.dll Version 5.2
Author                          : ofir
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Z2K400

Navigation menu