Motorola Mobility P56KY1 i296 PORTABLE iDEN/MOTOTALK MOBILE WITH BLUETOOTH User Manual Exhibit 12

Motorola Mobility LLC i296 PORTABLE iDEN/MOTOTALK MOBILE WITH BLUETOOTH Exhibit 12

Users Manual

FCC Filing Package for Motorola i296 Transceiver FCC ID: IHDP56KY1 Motorola Confidential Restricted iDEN, Motorola Inc., 600 North US Hwy 45, Libertyville, IL 60048, USA WWW.MOT.COM/iDEN Exhibit 8: Draft User’s Manual -- 47 CFR 2.1033(b)(3) The attached User’s Manual is the final production-intended version of the generic Motorola International English User Manual. This guide will be adapted to carrier-specific versions, but the key information herein will be retained. Translations into other languages will also be done to support the needs of other markets. Minor revisions may be made to these manuals, prior to and subsequent to, placing this product onto the market. Selected portions of the User Guide can be found as indicated below: 8.1 Part 15B Declaration of Conformity: Page 4 8.2 Safety Section: Page 84 8.3 Specific Absorption Rate (SAR) Data: Page 92 8.4 Guidance for use with Hearing Aids: Page 47, 97
User’s Guidei294i296
DECLARATION OF CONFORMITYPer FCC CFR 47 Part 2 Section 2.1077(a)Responsible Party Name: Motorola, Inc.Address: 8000 West Sunrise BoulevardPlantation, FL 33322 USAPhone Number: 1 (800) 453-0920Hereby declares that the product:Product Name: i294, i296Model Number: H88XAH6JR2BN (i294), H88XAH6JR2AN (i296)FCC-ID: IHDP56KY2 (i294), IHDP56KY1 (i296)Conforms to the following regulations:FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)FCC Notice to UsersThe following statement applies to all products that have received FCC approval. Applicable products bear the FCC logo, and/or an FCC ID in the format FCC-ID: IHDP56KY2 (i294), IHDP56KY1 (i296) on the product label.Motorola has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. See 47 CFR Sec. 15.21.Class B Digital DeviceAs a personal computer peripheral, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Sec. 15.19(3).Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.Industry Canada Notice to UsersOperation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device. See RSS-GEN 7.1.5.
Motorola, Inc.Consumer Advocacy Office600 North US Highway 45Libertyville, IL 60048www.hellomoto.comNote: Do not ship your phone to the above address. If you need to return your phone for repairs, replacement, or warranty service, please contact the Motorola Customer Support Center at:1-800-453-0920 (United States)1-877-483-2840 (TTY/TDD United States for hearing impaired)Certain mobile phone features are dependent on the capabilities and settings of your service provider’s network. Additionally, certain features may not be activated by your service provider, and/or the provider's network settings may limit the feature’s functionality. Always contact your service provider about feature availability and functionality. All features, functionality, and other product specifications, as well as the information contained in this user's guide are based upon the latest available information and are believed to be accurate at the time of printing. Motorola reserves the right to change or modify any information or specifications without notice or obligation.MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. Java and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.© Motorola, Inc., 2009.Manual Number: NNTN7906A
1HELLOMOTOIntroducing your new Motorola wireless phone. Here’s a quick anatomy lesson.Left Soft KeyPerform function in lower left display.Right Soft KeyPerform function in lower right display.End/Power KeyEnd calls, exit menu system, turns phone on/off.Talk KeyMake &answer calls.OK KeyIn menus & lists, press to select highlighted option.4-Way Navigation KeyOn/Off KeyVolume ButtonsPTT Button2.5mm Audio JackMicro USB ConnectorConnects charger and accessories.Speaker KeyMenu KeyFrom home screen,open main menu.
2check it out1234Press and hold thePower Key for afew seconds, or untilthe screen lights up,to turn on your phone.Customizable r keythat can be usedto open theSettings screen.Press the Navigation Keyup, down, left or right to highlight a menu feature.Press the r key to select.10:05pm 10/23Ready
3contentscontentscheck it out . . . . . . . . . . . 2menu map. . . . . . . . . . . . 6use and care . . . . . . . . . . 8essentials . . . . . . . . . . . . 9about this guide . . . . . . 9SIM card. . . . . . . . . . . 10battery . . . . . . . . . . . . 10turn it on & off . . . . . . 13enable security . . . . . . 13make a phone call. . . . 13answer a phone call . . 13advanced calling . . . . . 14make a private call . . . 14answer a private call. . 15store a phone number or private ID . . . . . . . . 16contacts . . . . . . . . . . . 16call a stored phone number or private ID . 17find your phone number and private ID 17messaging . . . . . . . . . 17MMS features . . . . . . 18inbox. . . . . . . . . . . . . . 21outbox . . . . . . . . . . . . 26sent items . . . . . . . . . 26customize messaging. 28datebook. . . . . . . . . . . 34using your phone as a modem. . . . . . . . . . . . 35basics. . . . . . . . . . . . . . . 36display . . . . . . . . . . . . 36main menu . . . . . . . . . 37text entry . . . . . . . . . . 37volume . . . . . . . . . . . . 40navigation key. . . . . . . 41handsfree speaker . . . 41transmitters . . . . . . . . 41use GPS with map software . . . . . . . . . . . 41features for the hearing impaired. . . . . 42TTY . . . . . . . . . . . . . . . 43security features. . . . . 44main attractions . . . . . . 45media center . . . . . . . 45PTX features . . . . . . . . 46one touch PTT . . . . . . 53PT manager . . . . . . . . 54Bluetooth® . . . . . . . . . 55call features. . . . . . . . . . 58turn off a call alert . . . . 58recent calls . . . . . . . . . 58
4contentsredial . . . . . . . . . . . . . . 59caller ID . . . . . . . . . . . . 59call forward . . . . . . . . . 59voice names . . . . . . . . 60emergency calls . . . . . 61international calls. . . . . 61speed dial . . . . . . . . . . 62voice mail . . . . . . . . . . 62selective dynamic group (SDG) calls. . . . . 63MOTOtalkTM. . . . . . . . . . 67switch to MOTOtalk . . 68exit MOTOtalk . . . . . . . 68channels and codes . . . 68private MOTOtalk calls 71making emergency calls while in MOTOtalkTM mode . . . 72setup options. . . . . . . . 73customize. . . . . . . . . . . . 75ring tones . . . . . . . . . . 75backlight . . . . . . . . . . . 76wallpaper . . . . . . . . . . . 76hide or show location . 77Legal and Safety . . . . . . 79Safety and General Information . . . . . . . . . 79Operational Precautions . . . . . . . . . 80RF Energy Interference/Compatibility . . . . . . . . 80Caring for the Environment by Recycling . . . . . . . . . . . 81Driving Precautions . . . 82Operational Warnings . 82Service and Repairs. . . 84Export Law Assurances . . . . . . . . . 84Battery Use and Safety 85Battery Charging . . . . . 87Specific Absorption Rate . . . . . . . . . . . . . . . 87AGPS and Emergency Calls. . . . . . . . . . . . . . . 88Limited Warranty Motorola Communications Products (International) 89Hearing Aid Compatibility With Mobile Phones . . . . . . 92Information From the World Health Organization . . . . . . . . 92Product Registration . . 93Wireless: The New Recyclable . . . . . . . . . . 93California Perchlorate Label . . . . . . . . . . . . . . 93Patent and Trademark Information . . . . . . . . . 93Software Copyright Notice . . . . . . . . . . . . . 94
5contentsPrivacy and Data Security . . . . . . . . . . . 94Smart Practices While Driving . . . . . . . . . . . . 95index . . . . . . . . . . . . . . . 97
6menu mapmain menu1NetLJava Apps• Java SystemuSettings• (see next page)0VoiceRecord• [New VoiceRec]LContacts• [New Contact]• [New SDG List]• [New Msg Group]EMessages• [Create Message]•Voice Mail• Inbox•Drafts• Outbox•Fax Mail• Net Alert• Sent ItemsPCall ForwardDDatebooklMemoMCall Timers•Last Call• Phone Reset• Phone Lifetime•Prvt/Grp Reset• Prvt/Grp Life• Kbytes ResetBRecent CallsKShortcuts•[New Entry]• 1)Shortcuts• 2)Cntcs[New Contact]• 3)Recent Calls•4)Contacts• 5)Datebook• 6)Messages• 7)VoiceRecord•8)Net• 9)Call ForwardJMy Info•My Name• Line 1• Line 2• Private ID•Group ID•Carrier IP•IP1 Address•IP2 AddressLQuick PTToProfilespCall AlertcGPS• Position•Privacy•InterfacetRing To n e s• Vibrate All: On/Off• Ringer• Vibrate• SilentPMOTOtalk•Go To MOTOtalk• Setup•HelpjMedia CentercBluetooth (i296 only)• Hands Free• Link to Devices• Device History• Setup• Find MeNPT Manager•Quick PTT• Send Message• Send Picture• Send Event• Send My Info• Send Contact• ConfigureThis is the standard Main Menu layout. Your phone’s menu may be a little different.
7settings menuDisplay/Info• Wallpaper•Text Size• Theme• Home Icons• Backlight•Clock• Menu View• Large Dialing• LanguagePhone Calls• Set Line•Any Key Ans• Auto Redial• Call Waiting• Auto Ans• Minute Beep• Call Duration• TTY• Hearing Aid• Notifications• DTMF Dialing• Prepend2-Way Radio• Tkgrp Silent•Tkgrp Area• One Touch PTT•Alert Type• PTT Quick Notes•On/Off PTT• Store Rcvd InfoPersonalize• Menu Options•Up Key•Down Key•Left Key• Right Key• Center Key• Left Sftkey• Right Sftkey•Power UpVo l um e• Line 1• Line 2• Messages• Earpiece• Speaker•Keypad• Java Earpiece• Java Spkr•DataSecurity• Phone Lock• Keypad Lock• SIM PIN•GPS PIN• Change PasswdsAdvanced• Alert Timeout• Headset/Spkr• Connectivity• Reset Defaults• Return to Home• Transmitters• Phone Only• Baud Rate
8use and careUse and CareTo care for your Motorola phone, please keep it away from:liquids of any kind dust and dirtDon’t expose your phone to water, rain, extreme humidity, sweat, or other moisture. If it does get wet, don’t try to accelerate drying with the use of an oven or dryer, as this may damage the phone.Don’t expose your phone to dust, dirt, sand, food, or other inappropriate materials.extreme heat or cold cleaning solutionsAvoid temperatures below 0°C/32°F or above 45°C/113°F.To clean your phone, use only a dry soft cloth. Don’t use alcohol or other cleaning solutions.microwaves the groundDon’t try to dry your phone in a microwave oven.Don’t drop your phone.
9essentialsessentialsCaution: Before using the phone for the first time, read the Important Safety and Legal information included in the gray-edged pages at the back of this guide.about this guideThis guide shows how to locate a menu feature as follows:Find it: / > u > Phone CallsThis means that, from the home screen:1Press the menu key / and then press the Settings u menu option .2Press the navigation keys to scroll to Phone Calls, and press the center key r to select it.symbolsThis means a feature is network or subscription dependent and may not be available in all areas, or might not be offered by your service provider. Contact customer service for more information.This means a feature requires an optional accessory.
10essentialsSIM cardinsert the SIM cardWarning: To avoid loss or damage, do not remove your SIM card from your phone unless absolutely necessary.batteryNote: Please consult “Battery Use and Safety” on page 85 before using this product.battery installation1Press down on the battery door latch, and slide the battery door up.
11essentialsbattery chargingNew batteries are not fully charged. charge using the charger1Pull out the connector cover, and insert the charger into the micro USB connector on your phone as shown.2Remove the battery door.3Push the battery down until it clicks in place.4Replace the battery door, and slide it toward the base of the phone until it locks into place.
12essentialscharge from your computerYou can partially charge your phone’s battery by connecting a Motorola-approved USB cable from your phone’s micro USB port to a high power USB connector on a computer (not a low-power one, such as the USB connector on your keyboard or bus-powered USB hub). Typically, USB high-power connectors are located directly on your computer.battery indicatorsdThe battery is at approximately 100% to 90% capacity when the indicator is blue and displaying three bars.eThe battery is at approximately 65% capacity when the indicator is green and displaying two bars.fThe battery is at approximately 10% capacity when the indicator is yellow and displaying one bar.gThe battery is at approximately 5% capacity when the indicator is red and has a flashing red bar.hThe battery is charging.
13essentialsturn it on & offTo turn on your phone, press and hold @ for a few seconds or until the display turns on. If prompted, enter your four-digit unlock code.Note: If you press the @ for more than four seconds, the phone will turn on in Transmitters Off mode. See “transmitters” on page 41.To turn off your phone, press and hold @ for a few seconds.enable securityYou will need to enable security the first time you power on your phone or within 10 days of first activation of your phone.1Press K under Ok.2You are prompted to enable security. Press K under Yes and follow on screen instructions.3Press @ to return to the home screen.make a phone callEnter a phone number and press ` or use a voice command. See “place a call using a voice name” on page 60.To hang up press @.answer a phone call•If you want to answer the call on speaker phone, press the speaker key ).•If you want to answer the call using the phone, press `. To hang up press @.
14essentials•If you are using a Bluetooth headset, press the answer key on your headset. To hang up press the key again.advanced callingmake a private callYour Private ID is the number at which you receive one-to-one Private calls.Talkgroup numbers are numbers through which you receive one-to-many group calls.to make a Private call1Enter the Private ID you want to call.2Press and hold the PTT button. Begin talking after your phone emits a chirping sound.3Release the PTT button to listen.To end the call press @.featurecall waitingTo accept the second call and put the active call on hold press K under Yes.To accept the second call and end the active call press `.3-way callMake or receive a phone call and press / > 3 Way. Enter the second phone number, press ` and K under Join.You cannot make any other calls during a three-way call, even if one party hangs up.any key answerTo answer phone calls by pressing any key on the keypad press / > u > Phone Calls > Any Key Ans > On.feature
15essentialsNote: A Private call ends automatically if there is no activity on the call for a few seconds.send call alertsSending a call alert discretely lets the recipient know that you want to talk to him or her on a Private call.When you send a call alert, the recipient’s phone displays your name and emits a series of beeps or vibrations.to send a call alert1Enter the Private ID you want to call.2Press K under Alert.When the message Ready To Alert appears on the display, press the PTT button until the message Alert Successful appears.answer a private call1When your phone emits a chirping sound or vibrates to indicate you are receiving a Private call, wait for the caller to finish speaking.2Press and hold the PTT button and begin talking after your phone emits a chirping sound.3Release the PTT button to listen.To end the call press @.answer a call alertWhen you receive a call alert, you cannot receive phone calls or Private calls until you do one of the following:optionAnswerPress the PTT button to begin a Private call with the sender.
16essentialsstore a phone number or private IDYou can store a phone number or private ID in Contacts:Find it: / > L > [New Contact]1Enter a name for the new entry. Each entry’s name can contain 20 characters. 2Select a Ring Tone.3Select a type for the entry (Mobile, Private1, Private2, Work1, Work2, Home, Email1, Email2, Fax, Pager, Talkgroup, IP or Other). To store a private ID choose Private1 or Private2.4Enter the number for the entry and press K under Save when done.contactsQueuePress K under Queue to store the call alert to the call alert queue.ClearPress K under Clear to dismiss and delete the call alert.optionfeatureedit/delete contact entryPress K under Contcs. Select a contact and press / > Edit. Change the desired content and press r. Press K under Save.set ringer IDPress K under Contcs. Select a contact and press / > Edit. Select Ringer and chose your desired ring tone. Press K under Back.
17essentialscall a stored phone number or private IDFind it: / > L1Scroll to the Contacts entry.2If the Contacts entry contains more than one number, scroll left or right until the type of the number you want to call is displayed (Mobile, Private1, Private2, Work1, Work2, Home, etc.).3If you chose a phone number, press ` to call the entry, or if you chose a Private ID, Talkgroup ID, or SDG List, press and hold the PTT button to call the number.find your phone number and private IDFind it: / > My InfomessagingYour phone has the ability to use both SMS and Multimedia Messaging Service (MMS) messaging. The type of messaging your phone uses will be determined by your service provider. Additionally, MMS allows you to send and receive messages that may include text, pictures, and audio files. create and send messages1From the home screen press K under Msgs > [Create Message].2Enter the phone number of the person you want to send the message to and press r or press K under Search. Select Contacts or Recent Calls to find the number you want.
18essentials3Select Mesg: and enter the text of the message or to use a quick note press K under QNotes and scroll to the quick note you want then press r.4If you want to send the message, press K under Send or to delete the message without sending it, press K under Cancel.quick notesWhen you are filling in the Mesg and Subject fields, you can add ready-made words or short phrases called Quick Notes. After you add these words or phrases, you can edit them as you would any other text. 1While you are creating a message, scroll to or select Mesg or Subject. 2Press K under QNotes.3Select the quick note you want to insert into the message. 4Press K under Send.MMS featuresNote: The following features are available only when using MMS.more message options To view more message fields in a message you are creating, select ....More....The following options become available:optionSubjectCreate or edit the subject line.AttachAttach a picture, audio file, or voice record.CcSend a copy of this message to someone else.Auto RepliesAllows you to create a list of possible short answers for the recipient to choose when replying to your message.
19essentialsinsert a picture and audio recordingYou can insert one or more pictures, and audio files from the media center into the body of the message. You can include text in the body of your message in addition to these items. insert items While you are writing your message, press /, select Insert and choose from Add QNotes, Add Picture, Insert Audio, or Record Voice.Select the picture or audio recording you want to insert. You can only insert one item at a time.To remove an item from a message, highlight it and press K under Delete.attach a picture or audio recordingYou can attach one or more pictures, audio or voice recordings from your phone to a message. You can include text in the body of your message in addition to these items. 1While you are filling in the Attach field, press [New] > and select from Browse Pictures, Browse Audio, or Record Voice.A list of available pictures, audio files, or voice recordings appears. 2Select the picture, audio or voice record you want to attach. PrioritySet priority Normal or High.Valid Until Set a date after which attempts to deliver the message end, or press K under No Date.option
20essentialsIf you want to attach more items, select [New].3When finished, press K under Done.Note: You can only attach audio files and pictures if they are not forward locked and if their DRM settings do not prevent you from sending.Forward locked items are usually copyright protected, and you cannot share them with anyone, such as in Private calls or by uploading them from your phone.create a new voice recordYou can create a new voice record to send with a message:1Press / or select Attach > [New].2Select Record Voice.3Say the message you want to record into the microphone. 4When you are finished recording, press r.5When finished, press K under Done.6The voice record is attached to the message and saved to the media center and the list of voice records. remove an attachmentTo remove an attachment in a message you are creating: 1Select Attach.2Scroll to the attachment you want to remove. 3Press / > Unattach.use draftsWhen you save a message as a draft, it is saved in the drafts folder.Find it: Press / > E > Drafts
21essentials1Select the draft you want to edit. 2To edit the fields you want to change, follow step 2 through step 4 in “create and send messages”.delete a draftWhen you send a draft, it is removed from the Drafts folder.1To delete a message in the Drafts folder without sending it, scroll to the message you want to delete and press K under Delete.2Press K under Yes to confirm. inboxFind it: Press / > E > Inboxreceive a message•To view the message, press K under Read.•To dismiss the message notification press K under Exit.While reading a text and numeric message that contains a phone number, you can press ` to call that number.threaded inboxThe threaded Inbox allows you to organize your messages by subject or sender. From the Message Center, press / > Threading, and select from None, Subject, or Sender.Note: Threading by subject is dependant upon your service provider.
22essentialsread from the message center1From the home screen press K under Mesg > Inbox.2Select the message you want to read. 3To reply to the message, press K under Reply.delete unread messages 1Scroll to the message you want to delete.2Press K under Delete and K under Yes to confirm.forward a message 1Press / > Forward. 2Create and send your message. Embedded objects and attachments are included when you forward a message. lock and unlock messagesLocked messages cannot be deleted until you unlock them. 1View the message you want to lock or unlock. 2Press / > Lock Message or Unlock Message. call a number in a message If a message you receive contains a phone number, Private ID, or Talkgroup ID in the From field, the To field, the Cc field, the Subject field, or the body of the message, you can call or send a call alert to that number. send a call alert 1View the message.2Highlight the Private ID or Talkgroup ID you want to alert. 3Press / > Alert.
23essentials4Push the PTT button. make a group call 1View the message. 2Highlight the Talkgroup ID you want to call.3Press /.4Select Talkgroup. 5Push the PTT button. store message information to contacts If a message you receive contains a phone number, Private ID, Talkgroup ID, or an email address in the From field, the To field, the Cc field, the Subject field, or the body of the message, you can store this information to Contacts. 1View the message. 2Highlight the number or email address you want to save. 3Press / > Save Number or Save Address. 4To store the number or email address as a new entry, select [New Contact].To store the number or email address to an existing entry, select the entry. 5With the Contacts type field highlighted, press the navigation key left or right to display the Contacts type you want to assign the number or email address. 6Press K under Save. reply to a message 1View the message you want to reply to.2To reply to the sender only, press K under Reply or press / and select Reply All to reply to all recipients.
24essentials3A list of short phrases appears. Select any of these phrases to add it to your messages or select [Create Reply].4Edit any message fields you want to change. 5Press K under Send.use auto repliesIf the message you are replying to was sent with auto replies, it contains a numbered list of possible replies for you to send. Press the number of the reply you want to send. The reply is sent immediately without further action.go to a websiteIf a message contains one or more website URLs, you can go to that website.1View the message.2Highlight the website URL you want to go to.3Press / > Go To Website.Note: The entire URL must appear in the message to allow you to open the website.embedded objects and attachments If a message contains pictures or audio files in the body of the message, highlight each picture or audio recording to view or play it. If a message contains a picture or audio recording as an attachment, open the attachment to view the picture or play the audio recording.open attachments1View the message.
25essentials2Highlight the attachment you want to open. Attachments appear at the end of a message.3Press r. Attachments of an unknown type cannot be opened, but can be deleted.save an embedded picture or audio recording To save a picture or audio recording that is part of the body of a message you receive: 1View the message. 2Highlight the picture or audio recording you want to save. 3Press /. 4Select Save Picture or Save Audio. The item will save in the default storage location. delete an embedded picture or audio recording To delete a picture or audio recording that is part of the body of a message you receive: 1View the message. 2Highlight the picture or audio recording you want to delete and press /.3Select Delete Picture or Delete Audio.save attachments 1View the message.2Highlight the attachment you want to save. 3Press / > Save Attachment. Selected items save to the default storage location.
26essentialsdelete attachments 1View the message. 2Highlight the attachment you want to delete. 3Press / > Delete Attachment. 4Press K under Yes to confirm. outboxThe Outbox holds all unsent messages.Find it: Press / > E > Outboxresending failed messages from the outbox1Scroll to the message you want to resend or press the number of the message you want to resend.2Press K under Resend.cancel an unsent message1Highlight the message you want to cancel.2Press /.3Press K under Cancel.sent itemsThe Sent Items box holds sent messages.forward messages from sent items1Scroll to the message you want to forward.2Press / > Forward. 3Make edits if you wish, select the recipient and press K under Send.
27essentialssetting up delivery reportsWhile creating a message you can set up read receipts. Press / > Delivery Report to view the options.check delivery status If a message was successfully sent and you set the message to confirm delivery, you can check the delivery status: 1Scroll to the message you want to view.2Press / > Delivery Status. delete sent messages1Scroll to the message you want to delete.2Press K under Delete.3Press K under Yes to confirm.delete all unlocked sent messages1Press / > Delete All.2Press K under Yes to confirm.optionOffDelivery report will not be generated.OnDelivery report will be generated when a message is delivered.Note: Delivery reports are available with MMS only.
28essentialscustomize messagingFind it: / > E > / > SetupThis option is available from many menus.The following options are available: manage memoryYour text Inbox and Sent Items hold 200 messages each. The Outbox, and Drafts folder hold up to 30 messages each. If they are full, you cannot receive messages, send optionSignature Allows you to create a signature that is automatically inserted at the end of your messages. Signatures can be edited before sending the message. Quick NotesLets you create new Quick Notes and edit or delete Quick Notes you created. CleanupControls how long messages remain in the Inbox and Sent Items before being deleted. Delivery Rp: Allows you to be automatically notified when your message is delivered.Memory SizeShows a report on used and free memory in your phone.MMS SetupOpens a submenu to set MMS options. Note: Available with MMS only.Text Message Setup:Opens a submenu to set text messaging options. Note: Available with SMS only.option
29essentialsmessages, or save drafts until you delete some items.Note: Media files and Java applications can affect the available amount of memory on your phone. If you run out of memory and your Inbox, Sent Items, Outbox, and Drafts folder are empty, delete unwanted media files and Java applications to free up memory.To view the amount of memory available in your text inbox:Find it: Press / > E > / > Setup > Memory SizeMMS setupFind it: / > E > / > Setup > MMS Setup The following options become available: optionFriendly NameAllows you to create a friendly name. Your friendly name is displayed in the From field on other iDEN phones when your message is received. Downloads Downloads: Controls whether your phone downloads new messages. Set this option to Automatic if you want your phone to download new messages automatically. Select Manual if you want your phone to prompt you before downloading new messages.
30essentialstext message setupFind it: / > E > / > Setup > Text Msg setup The following options become available: new quick notes and reply phrases create quick notes or replies1From the Setup menu, select Quick Notes, or select MMS Setup > Replies. 2Select [New Quicknote], or [New Reply]. 3Enter text from the keypad and press r.edit quick notes or repliesYou can edit only Quick Note phrases you have created. 1From the Setup menu, select Quick Notes, or select MMS Setup > Replies. 2Select the quick note or reply you want to edit. 3Edit the text and press r. Replies Replies: Lets you create or edit and delete reply phrases you created. optionSrvc Cntr NoAllows you to enter a service center number. Expire AfterAllows you to set the number of days before a message expires.option
31essentialsdelete quick notes or replies you have created1From the Setup menu, select Quick Notes, or select MMS Setup > Replies. 2Scroll to the quick note you want to delete. 3Press K under Delete. 4Press K under Yes to confirm. delete all quick notes or replies you have created1From the Setup menu, select Quick Notes, or select MMS Setup > Replies. 2Press / > Delete All. 3Press K under Yes to confirm. cleanup optionsThe cleanup option controls how long and how many messages remain in the Inbox and Sent Items before they are deleted. You set the cleanup option for the Inbox and Sent Items separately. The clean up option deletes only read, unlocked messages and sent messages. Find it: / > E > / > Setup > Cleanup1Select Inbox or Sent Items.2Choose a clean up option from the following list:optionOffMessages are never automatically deleted.5 MessagesIf you have more than 5 messages, messages are deleted in the order they were received, starting with the oldest, until 5 are left.
32essentials3Press K under Yes to automatically delete messages now or press K under No to delete messages later. delete all messages Find it: / > E 1Select Inbox, Drafts, Sent Items, or Outbox.2Press / > Delete All. 3Press K under Yes to confirm.10 MessagesIf you have more than 10 messages, messages are deleted in the order they were received, starting with the oldest, until 10 are left.1 DayMessages are deleted if they are older than 1 day. 3 DaysMessages are deleted if they are older than 3 days. With these options, messages are deleted when you exit the message center after setting the option.F-In F-OutMessages are deleted as necessary on a FirstIn FirstOut basis.optionCustomLets you create a clean-up option of up to 199 messages or 99 days for the Inbox and Sent Items.option
33essentialsdelete a thread1From the Inbox, select a thread.2Press / > Delete Thread. 3Press K under Yes to confirm.message notificationsWhen you receive a message, your phone notifies you with text on the display, a notification tone or vibration.You can access the message or dismiss the notification.If you dismiss the notification, the message is not deleted. It can be accessed through the message center.If you are not on a phone call when you receive a message, your phone sounds a notification tone every 30 seconds until you access the message or dismiss the alert.If you are on a call when you receive a message, your phone may sound a notification tone during the call or after you end the call, depending on how you set your notification options.set notification optionsTo control whether your phone sounds message notification tones while you are on a phone call:Find it: / > u > Phone Calls> NotificationsSelect from these options:optionReceive AllTones sound during calls for all types of messages.Msg Mail OnlyTones sound during calls for mail messages; tones for all other types of messages are held until you end calls.
34essentialsTo set notification options during a call press / > Call Setup > Notifications.datebookDelay AllTones for all types of messages are held until you end calls.Note: Delay All is the default setting.featurecreate datebook eventsTo create a new Datebook event press / > Datebook > [New Event].see datebook eventTo see a calendar event press / > Datebook. Press the navigation key left or right to see the day and up or down to see the events.optionevent reminderWhen an event reminder occurs press K under View.Press K under Back to close the reminder.receive datebook events via PTTTo view the information while still in the Private call press r.The 5 most recent events received from a Private ID are stored with that Private ID on the recent calls list.To store events to the Datebook press K under Save while viewing the event you want to store.feature
35essentialsdatebook setupFind it: / > Datebook > / > SetupYou can view or change these options:using your phone as a modemYour phone can be connected to a computer via USB for use as a modem. For more specific information on how to setup your phone for use with your computer please visit www.motorola.com/support and look under the FAQ section.optionsStart ViewSets Datebook to start in day view, week view, or month view when you access Datebook.Daily BeginSets the beginning of your day. This is the earliest time of day displayed in week view, if you have a 12-hour day view.Delete AfterSets the amount of time Datebook waits to delete an event after it occurs.Time ShiftLets you shift the times of all Datebook events. This is useful if you are traveling to a different time zone.Alert TimeoutSets the amount of time a tone continues to sound when you receive a Datebook reminder.Clock Controls whether the time and date appear on the home screen; sets time and date format; sets year.options
36basicsbasicsSee page 1 for a basic phone diagram.displayThe home screen shows when you turn on the phone. To dial a number from the home screen, press number keys and `.Note: Your home screen may look different.Soft key labels show the current soft key functions. For soft key locations, see page 1.status indicatorsStatus indicators are shown at the top of the home screen:1Signal Strength Indicator: Vertical bars show the strength of the network connection. You can’t make or receive calls when ~ shows.10:05pm 10/23Ready DateRight Soft Key LabelLeft Soft Key Label Time10:05pm 10/23Ready DateRight Soft Key LabelLeft Soft Key Label Time1. 2. 3. 4. 5. 6. 7.
37basics2Active Phone Line: $ indicates phone line 1 is ready to make calls; ( indicates phone line 2 is ready to make calls.3Speaker On/Off: Sounds associated with Private calls and group calls can be set to come through the earpiece rather than through the speaker.4Ringer Vibe/Off: Your phone is set to not ring.5 Message Indicator: Shows when you receive a text message.6Packet Data: Your phone is ready to transfer packet data or is transferring packet data when it shows a blinking arrow.7Battery Charge Indicator: A fuller battery indicates a greater charge. Recharge the battery when your phone shows Low Battery.main menuAll your phone’s features can be accessed through the main menu. You can set the main menu to appear as List View or Icon View.Find it: / > u > Display/Info > Menu Viewtext entryYour phone provides convenient ways to enter words, letters, punctuation, and numbers whenever you are prompted to enter text (for example, when adding a Contacts entry or when using Text Messaging).change the character input mode1When you see a screen where you can enter text, press / to change the character input mode.
38basics2Select one of the following options:Tip: When entering text, press and hold # to change letter capitalization (Abc > ABC > abc).word methodThe Word text input method lets you enter text into your phone by pressing keys just once per letter.The Word text input method combines the groups of letters found on each phone key with a fast-access dictionary of words, and recognizes what you want to text as you type. It first offers the most commonly-used word for the key sequence you enter and lets you access other choices with one or more presses of the 0 key or ny pressing the navigation key up or down. You may also hold the navigation key down to display a pop-up list of choices.entry methodAlphaPress a key several times for different characters.WordEnter words using a predictive text entering system that lets you enter a word with fewer keypresses.SymbolsEnter symbols.NumericEnter numbers by pressing the numbers on the keypad.Text Input SettingsSelects the desired entry languages and Word Prediction features.InsertSelects a item to be inserted, such a picture, an audio clip or a voice recording. Note: available only when using MMS messaging.
39basicsenter a word using “word” method character input1Select the Word character input method. 2Press the corresponding keys once per letter to enter a word (for example, to enter the word Bill, press 2455). (If you make a mistake, press * to erase a single character. Press and hold * to delete an entire entry.)3To accept a word and insert a space, press#.To accept a word completion (such as Billion when you entered Bill), press ; right.If you get a word you don’t want, you can press the 0 key to see more word choices and pick the one you want.alpha methodTo enter characters by tapping the keypad: 1Select the Alpha method.2Press the corresponding keys repeatedly until the desired letter appears. (For example, to enter the word Bill, press 2 twice, 4 three times, 5 three times, and 5 three times again. If you make a mistake, press Delete to erase a single character. Press and hold Delete to erase an entire word.)By default, the first letter of an entry is capitalized and the following letters are lowercased. After a character is entered, the cursor automatically advances to the next space after two seconds or when you enter a character on a different key.Characters scroll in the following order: characters1Space . 1 ? ! , @ & : ; “ - ( ) ‘ ¿ ¡ % £ $ ¥2A B C 2 Á Ã Â À Ç
40basicsWhen entering text, press and hold # to switch between lowercase and uppercase letters. The icons in the upper left-hand corner of the screen show the character type.volume Press the volume keys up or down to:•change the earpiece volume during calls•change the ringer volume from the home screenTip: You can quickly set your ringer to Vibrate All by holding the down volume key in the home screen.3D E F 3 É Ê È4G H I 4 Í Ì5J K L 56M N O 6 ñ Ó Õ Ô Ò7P Q R S 7 ß8T U V 8 Ú Ü Û Ù9W X Y Z 90+ - 0 * / \ [ ] = > < # §#Space / Shift*Backcharacters character typeQ or TLowercaseR or UUppercaseS or VShift LockWNumericalXSymbols
41basicsnavigation keyPress the navigation key up, down, left, or right to scroll to items in the display. When you highlight the desired item, press r to select it.handsfree speakerYou can use your phone’s handsfree speaker to make calls without holding the phone to your ear.During a call, press K under Spkr to turn the handsfree speaker On.The handsfree speaker stays on until you press K under Spkr again.transmittersConsult airline staff about the use of the Transmitters Off feature during flight. Turn off your phone whenever instructed to do so by airline staff.Transmitters Off turns off your phone’s calling and Bluetooth features in situations where wireless phone use is prohibited, but you can use the phone’s other non-calling features when Transmitters is turned Off.Find it: / > u > Advanced > Transmitters > Offuse GPS with map softwareYour phone can be connected to a PC, laptop, or PDA via USB for use as a GPS receiver. For more specific information on how to setup your phone for use with your computer please
42basicsvisit www.motorola.com/support and look under the FAQ section.features for the hearing impairedusing your phone with a hearing aidFor best results use the following optimization procedures and phone setting. They generally apply as well for users with cochlear implants:optimize your phone position and orientationWhile in a phone call slide your phone up and down, then left and right until best microphone coupling is obtained. You also may need to adjust your hearing aid (HA) volume setting.If your HA has a telecoil, activate its switch, then also rotate the phone as illustrated to align the telecoils.Note: Some automatically switched hearing aids may need an auxiliary switching magnet.If you are unsure whether your HA is telecoil equipped or needs an auxiliary magnet, please refer to your HA user guide or contact a hearing aid professional or supplier.
43basicschoose your hearing aid settingFind it: / > u > Phone Calls > Hearing Aid1Set this option to Microphone. Microphone coupling is now optimized. or2Set this option to Telecoil. Phone meets US federal requirements for telecoil coupling sound or set this option to Off (factory default). This is the setting for non HA users.TTYApproximate telecoil location is just above the battery.Approximate telecoil location is within 6-13 mm of this location.Off - Shut offM - MicrophoneT - Telecoilfeatureturn On TTY featurePress / > u > Phone Calls > TTY > Use TTY > On.choose TTY modePress / > u > Phone Calls > TTY > Type.Select from TTY, VCO or HCO.change the TTY baud ratePress / > u > Phone Calls > TTY > Baud.Select 45.45 or 50.00.change TTY mode during a callWhile in the TTY call, press / > In Call Setup > TTY > Type.Select from TTY, VCO or HCO.
44basicssecurity featuresNote: You can make emergency calls on a locked phone (see page 61).featurephone lockTo lock the phone press / > u > Security > Phone Lock > Lock Now or Auto Lock.keypad lockTo lock the keypad press / > u > Security > Keypad Lock > Lock Now or Auto Lock.Shortcut: To l ock the keypad press / > *.enable SIM PINPress / > u > Security > SIM PIN > On.change SIM PIN Press / > u > Security > Change Passwords > SIM PIN.
45main attractionsmain attractionsmedia centerThe media center lets you access pictures and audio recordings stored in your phone’s memory.The following audio recordings can be accessed through the media center:•Voice records•Ringtones•Audio recordings saved from MMS messages•Audio recordings downloaded to your phoneItems in the media center can be sent in MMS messages and with Bluetooth. See “MMS features” on page 18 and “Bluetooth®” on page 55.Pictures in the media center can be sent in Private calls using Send via PTT. See “PTX features” on page 46.Audio files supported by the Media Center include:FormatSampling Rates/Bit Rates.au 8 KHz/8 kbps.midi 8 KHz.mp3 8 KHz/8 kbps.wav 8 KHz/64 kbps.amr 12kbps
46main attractionsImage files supported by the Media Center include:PTX featuresWith Push To View features, your phone can send and receive the following items through Private calls with other phones that have this capability:•Short text messages1•Pictures1•Datebook events•My Info•Contact informationYou can choose to send messages, pictures, events, My Info or Contacts information to the Private ID you are engaged in a Private call with, Private IDs on the Recent Calls list, and Private IDs stored in Contacts.When you make or receive a Private call, your phone automatically determines whether the phone you are engaged in a Private call with is able to receive each of these items. Your phone saves this information for as long as the Private ID is on your Recent Calls list or is saved in your Contacts. Your phone updates the saved information each time you make or receive a call to or from that Private ID.Note: You cannot send PTT feature items during Talkgroup calls or SDGC calls.FormatMax. Image Size (in pixels).png 128 x 160.gif 128 x 160.jpg 640 x 480.wbmp 128 x 1601. Additional charges may apply.
47main attractionssend messagesThe Push to Send Messages feature lets you send short text messages through Private calls.When you send a message, it appears on the display of the phone you are engaged in the Private call with.begin a message and choose a recipient You can begin a message during a Private call, from the Contacts list, the Recent Calls list, or from the PT Manager.begin a message during a Private callWhile in a Private call, press / > Use PTT Feature > Send Message.Note: The first time you send a message, Messaging Fees May Apply Continue? appears and you are prompted to respond. Press K under Yes to acknowledge the message.begin a message from the Contacts or the Recent Calls list1From the Contacts or the Recent Calls list, select the entry containing the Private ID you want to send the message to.2Press / > Use PTT Feature > Send Message.begin a message from the PT ManagerThe PT Manager lets you select the Private ID you want to send the message to from Contacts or the Recent Calls list.Find it: / > N > Send Contact > BrowseThen select Contacts or Recent Calls to see a list of entries from the Contacts or the Recent Calls list that can receive messages.
48main attractionscreate messagesAfter you have begun a message and chosen a recipient, a screen appears that lets you create the text of the message you want to send. Your message may be up to 400 characters long. You can choose from a list of ready-made words or short phrases called Quick Notes. You can use a Quick Note as it is or edit it before you send it. Editing a Quick Note changes the Quick Note for this message only and will not change the Quick Note on the list. send a completed messageAfter you have completed your message, press the PTT button to send it.receive messages When you receive a message, a message notification appears on the display. To view the message, press K under Read. To dismiss the message, press K under Dismiss.reply to a message1View the message.2Press K under Reply.3Create the message and press the PTT button to send it.send picturesYou can send pictures stored in the Media Center through Private calls. The picture you send appears on the Private call recipient’s display. If the recipient accepts the picture, their phone saves the picture. The picture then appears in that phone’s recent call list.
49main attractionsThe first time you send a stored picture after turning the phone on, Picture Fees May Apply Continue? appears and you are prompted to respond.Note: You cannot make or receive Private calls while transmitting or receiving a picture.send a picture during a call1While in a Private call, press K under Picture or press / > Use PTT Feature > Send Picture.A list of pictures that can be included in a Private call appears.2Select the picture you want to send.3Press the PTT button to send the picture. 4Wait while the picture is transmitted. The Private call is temporarily interrupted while a picture is transmitted. 5When prompted, press the PTT button to resume the Private call. start a call by sending a picturefrom the media centerFind it: / > Media Center1Scroll left or right to Media: Pictures.2Select the picture you want to send.3Press / > Send Via... > Send Via PTT.4Select A Contact or A Recent CallA list of contacts that have Private IDs and are able to receive pictures appears.5Select the name of the person you want to send the picture to.6Press the PTT button to send the picture. 7When prompted, press the PTT button to resume the Private call.
50main attractionsfrom the PT manager:Find it: / > N > Send Picture1Select A Contact or A Recent CallA list of contacts that have Private IDs and are able to receive pictures appears.2Select the name of the person you want to send the picture to.3Select Browse Picture.4Press the PTT button to send the picture.5Once picture has been sent, when prompted press the PTT button to resume the call.receive a picture When someone sends you a picture, your phone emits a tone or vibrates and a message appears asking if you want to accept the picture. Pictures you receive are saved to your phone’s memory. They are accessible through the media center. When you see a message asking if you want to accept the picture, press Yes to accept or No to decline.clear a picture from the displayIf you want to clear a picture from your phone’s display while still on a call, press / > Clear Screen. send a datebook eventTo send a datebook event during a private call:1While in a Private call press / > Use PTT Feature > Send Event. Note: If these options do not appear on the menu, the Private ID you are engaged
51main attractionsin a private call with is not able to receive Datebook events.2If you want to create a new datebook event, press K under New and create the event in your datebook. If you want to chose an existing event do so.3If the event is a recurring event: Select This Event Only to send only the event selected. Select Repeat Events to send all occurrences of the event.4Push the PTT button to send the event.send my info•While in a Private Call press / > Send via PTT > Send My Info, and push the PTT button to send.•From the home screen press / > My Info > / > Send via PTT. Enter a Private ID or press K under Browse to chose a recipient from Contacts, Recent Calls or Memo, and press r. Push the PTT button to send.set my info sending optionYou can control what portion of the information in My Info is sent and whether it is sent automatically in every call or only when you choose to send it. Find it: / > PT Manager > Configure > PTT My Info > Info to Send1Select or remove the fields you want to send.2Press K under Done.The information your phone sends always includes My Name, and Private. You may also send Line 1, Line 2, and Carrier IP, depending on your sending options.
52main attractionsautomatic sending To control whether you send your information automatically: Find it: / > PT Manager > Configure > PTT My Info > Auto Send1Select On or Off2When you make a call in which your information is sent automatically, the name you entered in the My Name field of My Info appears on the display of the recipient’s phone, even if your name and Private ID are not stored in the recipient’s Contacts.send contact informationsend contact during private call1While in a Private Call press / > Use PTT Feature.2Select Send Contact and select the contact information you want to send.3Push the PTT button to send.send contact from home screen1From the home screen press / > PT Manager > Send Contact.2Enter the Private ID number of the person you want to send the Contact information to or press K under Browse.3Select from Recent Calls, Contacts, or Memo.4Select the contact information you want to send and push the PTT button.turn PTT features on and off You can turn your phone’s ability to send and receive messages, pictures, and Datebook events on and off.
53main attractionsYou cannot turn your phone’s ability to send and receive My Info and contact information on and off. Find it: / > u > 2-Way Radio> On/Off PTT1Check or uncheck Messages, Pictures or Events.one touch PTTFind it: / > u > 2-Way Radio > One Touch PTTOne Touch PTT sets your phone to do any of the following each time you press the PTT button from the home screen:optionOffNothing happens when you press the PTT button from the home screen.Quick PTT Go to Quick PTT. See “quick PTT” on page 54.Last Call Call the most recent Private ID or Group on the recent calls list. Assigned No.Call a Private ID you assign. Enter the number using your keypad, or press K under Search. Select Contacts, Recent Calls, or Memo.Note: If you are entering a Talkgroup number, enter # before the number.PT ManagerGo to PT Manager. See “PT manager” on page 54.Send Message: Go to the first screen to send a message.Send Picture: Go to the first screen to send pictures. See “send pictures” on page 48.option
54main attractionsquick PTTQuick PTT lets you quickly make a call, create an SDG list or make an SDG call when accessing any Private IDs on your phone. To view a list of Contacts and SDG lists with Private IDs in Contacts: Find it: / > Quick PTTTo move between Contacts, Recent Calls, or Memo, press the navigation key left or right.To make a Private call or SDG call: 1Select the entries you want.2Press K under Done.3Push the PTT button.To save your selections as an SDG list press / > Save SDG. For more information about SDG lists, see “selective dynamic group (SDG) calls” on page 63.If you want to assign a name to the SDG list, enter the name.Note: If you do not assign a name, the SDG list is named SDG followed by the number of members in the SDG list. For example, SDG (8) for an SDG list with 8 members.PT managerThe PT Manager lets you quickly access PTT features, and other Private call features, from the main menu. Send EventGo to the first screen to send a Datebook event.Send My InfoGo to the first screen to send My Info. See “send my info” on page 51.Send ContactGo to the first screen to send a contact. See “send contact information” on page 52.option
55main attractionsFind it: / > PT Manager•Select Quick PTT, Send Message, Send Picture, Send Event, Send My Info, Send Contact, or Configure. After choosing what PTT item you are sending, select a contact and press the PTT button to send.•Select Configure to configure your PTT Quick Notes, PTT My Info, One Touch PTT, or On/Off PTT.Bluetooth® Note: Bluetooth supported on i296 only.Find it: / > cturn Bluetooth on or offYou can turn your phone’s Bluetooth feature on or off. While Bluetooth power is on, your phone can communicate with other devices.Find it: / > c > Setup > Power1Select On to power Bluetooth On.2Select Name if you wish to assign a name to your phone.3Select Find Me Time to determine the amount of time in which your phone can be found by other Bluetooth devices.You can turn off Bluetooth if you want to prolong battery life or if you enter an area where Bluetooth is prohibited.make a Bluetooth connectionconnect your phone with a Bluetooth headsetFind it: / > c > Hands Free1Follow the instructions on your Bluetooth headset to set it up to be found.2Once your Bluetooth headset is set to be found, select [Find Devices]. Your phone will scan for all Bluetooth devices in range.
56main attractionsSelect your Bluetooth headset from the list of devices and press r.3Your phone requires that you pair it with the Bluetooth headset in order to create a connection. Press K under Yes when you are prompted to pair with the headset.4Enter the Bluetooth pass key.Some Bluetooth devices ship with Bluetooth PINs. Please refer to your Bluetooth device’s user guide to locate this information.If a device ships without a Bluetooth PIN, then you can enter any PIN for that device.This phone offers the Bluetooth auto pair feature with auto pair compatible Motorola devices. When paired via Bluetooth with a certain device, the PIN will not be required.5Press K under Ok.Note: Once your phone and headset have been paired, it will be stored on your phone and you will not need to pair them again unless the device is removed from memory.connect your phone with another Bluetooth deviceFind it: / > c > Link To Devices1Select the device you want from the list of found devices on your screen.2Create a bond if you are prompted to do so.If you have previously connected to a device, the device will be stored on your phone so you can connect with it easily.use Bluetooth during a callYou can connect with available Bluetooth devices during a call.1While in a call, press / > Use Bluetooth.
57main attractions2Select the audio device you want to connect to from the list of Hands Free Devices.If the Audio Devices list contains only one device, your phone will try to connect to it.send information via BluetoothYour phone can transfer Contacts entries, Datebook events, audio files, and pictures to another Bluetooth device.The receiving device must be within 32 feet (10 meters) of your phone in order to connect.Note: Files sent or received may be up to 1 MB, depending on your service provider.sending information1From within Contacts, datebook, or Media Center, select the Contacts entry, Datebook event, audio file or picture you want to send.2Press / > Send Via... > Bluetooth.3Select the device you want to transfer the contact information to, or search for the device by selecting [Find Devices].4If prompted, bond with the device.Your phone connects with the devices and transfers the information.
58call featurescall featuresturn off a call alertYou can press the volume keys to turn off a call alert before answering the call.recent callsThe recent calls list contains information associated with calls you have made and received and call alerts you have received.When you send or receive Private calls, the recent call list contains the following PTX items with those calls:•contact information received•My Info received•short text messages received•pictures sent or received•Datebook events receivedThe recent calls list displays up to 20 of the most recent calls and call alerts.1Press / > Recent Calls.2Scroll through the list.3To view more details of the item press r.store an item to contacts from recent callsPhone calls, Private calls, My Info, Contacts or Location entries received from other phones can be stored to the Contacts list from the Recent Calls list.
59call featuresFind it: / > Recent Calls1Scroll to or select the item you want to store.2Press K under Save to store the information as a new entry in the Contacts list.or3Select an existing contact and update the information.4Press K under Done to save your changes.redialTo redial your last outgoing call, press and hold ` or push the PTT button if it was a private call.caller IDCaller ID allows people to identify a caller before answering the phone by displaying the number of the incoming call.To block your phone number from being displayed for a specific outgoing call:1Press *67.2Enter the number you want to call.3Press `.To permanently block your number, call your customer service provider.call forwardCall forwarding sends calls to the phone numbers you specify. You can forward all calls to one number or forward missed calls to different numbers depending on the reason
60call featuresyou missed the call. You can forward phone lines 1 and 2 independently.Find it: / > Call Forward1To forward all calls select All Calls and select To to enter the phone number you want all your calls forwarded to.or2You can specify a forwarding number for each type of missed call by selecting Detailed and choosing the following options:If Busy: When your phone is on a call or transferring data.If No Answer: When you do not answer on the first 4 rings.If Unreachable: When your phone is out of coverage or powered off.voice namesYou can place calls by speaking commands to your phone if you have previously assigned a voice name to your contacts.assign voice names to contacts1Press K under Contcs and select [New Contact].2Assign a name, phone number and select [Options].3Select Voice Name and follow the prompt to record the voice name.4Press K under Back and K under Save.place a call using a voice name1Press the speaker key ) until you are prompted to say the voice name.The phone will automatically place the call.
61call featuresemergency callsYour service provider programs one or more emergency phone numbers that you can call under any circumstances. Emergency calls can be made without a SIM card, when your phone is locked, or when the SIM card is blocked.Note: Emergency numbers vary by country. Your phone’s preprogrammed emergency number(s) may not work in all locations, and sometimes an emergency call cannot be placed due to network, environmental, or interference issues.Dial 911 or your local emergency number to be connected to an emergency response center. If you are on an active call, you must end it before making an emergency call. When you make an emergency call, your phone’s GPS Enabled feature can help emergency service personnel find you, if you are in a location where your phone's GPS antenna has established a clear view of the open sky and your local emergency response center has the equipment to process location information. Because of the limitations of this feature, always provide your location, to the best of your knowledge, to the emergency response center when you make an emergency call.Note: Emergency calls cannot be placed while the keypad is locked, or if your phone is displaying a No Service message on the screen. To unlock the keypad, press / > *.international callsIf your phone service includes international dialing, press and hold 0 to insert your local international access code (indicated by +). Then, press the keypad keys to dial the country code and phone number.
62call featuresspeed dialEach phone number stored in Contacts is assigned a Speed Dial number, which you can use to call that number.1From the home screen, use the keypad to enter the Speed Dial number assigned to the phone number you want to call.2Press #.3Press `.turbo dialThe first nine entries in your contacts are set for turbo dial. They can be called by pressing and holding the speed dial number (1 through 9).voice mailTo receive voice mail messages, you must first contact your service provider to set up a voice mail account.receiving a messageWhen you receive a voice mail message, New VoiceMail Message appears on the display.To call your service provider’s voice mail system and listen to the message:1Press K under Call.2To dismiss the message notification:•Press r or Back.If the caller leaves a message, 3 appears on the display.
63call featuresselective dynamic group (SDG) callsAn SDG call is similar to a Private call, but is made to all members of an SDG list at once. An SDG list is a group of Private IDs that you create. An SDG list must contain at least 2 members and can contain up to 20 members.You can create an SDG list for one call only or store it to Contacts so you can call it any time.Note: In order to store SDG lists on your phone, you you will need an SDG-capable SIM card. For more information about SDG-capable SIM cards, contact your service provider. SDG lists created with your phone are not readable by an older iDEN SIM-based phone.You can use Send via PTT to send SDG lists to other phones that have this capability.create SDG lists in contactsFind it: / > L1Select [New SDG List].2If you want to assign a name to the SDG list, enter the name.If you do not assign a name, the SDG list is named “SDG” followed by the number of members in the SDG list. For example, “SDG (8)” for an SDG list with 8 members.3Add Private IDs. See “Add Private Numbers” below.4Press K under Save.add private numbersYou can add Private IDs to an SDG list by selecting them from Contacts, the recent calls list, or memo. You can add all members in an existing SDG list by selecting the list.
64call featuresYou can select more than one member from Contacts and the recent calls list. A checkmark appears next to each selected item.add members from contacts, the recent calls list, or memo1While creating an SDG list, select [Add Member] or select [Add Number] and press K under Browse.2Scroll to the members you want from Contacts, the recent calls list, or Memo, and press r. A checkmark appears next to each selected member. If you chose [Add Number] in step one, you can enter a Private ID number from the keypad. 3Press K under Done.remove members or SDG listsremove a member from an SDG list1From Contacts, scroll to the SDG list you want to delete the member from.2Press K under Edit.3Scroll to the member you want to remove. 4Press / > Remove Member.5Press K under Save.remove all members from an SDG list1From Contacts, scroll to the SDG list you want to delete the member from.2Press K under Edit.3Press / > Remove All.4Press K under Yes to confirm.delete an SDG list from Contacts1Scroll to the SDG list you want to delete.
65call features2Press / > Delete SDG List.make SDG calls1From Contacts or the recent calls list, scroll to or select the SDG list you want.2Push the PTT button.start an SDG call with a private ID1From the home screen, enter the Private ID, or from the Contacts list or the recent Calls List, scroll to an entry containing the Private ID.2Press / > Call SDG.3Add more Private IDs. See “add private numbers” on page 63.If you want to save the SDG list you have created press / > Save SDG, or if you do not want to save the SDG list, press K under Done.4Push the PTT button to make the call. SDG call informationWhile you are in an SDG call, the following appears on the screen:•The name of the SDG list•The name or the Private ID of the person speaking•The number of participants in the SDG callSDG Call DetailsDuring an SDG call, you can view details about the other SDG list members, such as their name or Private ID, and their status on the call. To view SDG call details, press K under Details.
66call featuresIn the SDG Call Details view, these icons appear next to member names or Private IDs:FThe member of the SDG list who is speaking.EA member of the SDG list who is active on the SDG call, but not speaking.DA member of the SDG list who has exited the call.HA member of the SDG list who could not be reached on the SDG call.GA member of the SDG list whose status is unknown.
67MOTOtalkTMMOTOtalkTM Note: This feature may not be offered by your service provider.With MOTOtalk, you can make and receive Two-Way Radio calls without network coverage. If you are travelling outside your service provider's coverage area, receiving a poor signal, or otherwise want to temporarily avoid using your service provider's network, you can switch to MOTOtalk and talk with anyone on your code and channel who is within range.Note: Range will vary based on terrain, man-made structures and atmospheric conditions.MOTOtalk lets you:•Use code or private mode operation•Use up to 10 channels•Communicate with standalone MOTOtalk radiosNote: You cannot use MOTOtalk with older Family Radio Services products.The following features and main menu items are unavailable while in MOTOtalk:•On-network phone or Private calls•Data transmission•Incoming message notification•Datebook•Call forwarding•Call Timers•Call alerts
68MOTOtalkTMswitch to MOTOtalkTo set your phone to MOTOtalk:1From the home screen press / > MOTOtalk and press r.2Select Go to MOTOtalk.Switching to MOTOtalk Please Wait displays.After a few seconds, the MOTOtalk home screen displays. When MT Ready displays, you can begin using MOTOtalk. While in MOTOtalk, this icon 4 displays.exit MOTOtalkTo switch to network mode:1From the MOTOtalk home screen, press / > MT Options and press r.2Select Exit MOTOtalk.Switching to Network Please Wait displays. After a few seconds, the network home screen appears.talk rangeWhile in MOTOtalk mode, phones should be a minimum of 6 feet apart to maximize performance and improve transmission range. channels and codesYour phone has 10 channels and 15 codes. Channels are divided into sets of frequencies. Other parties may be talking on the same channel. Codes minimize interference from other parties when you are sharing the same channel.MOTOtalk opens to the last code and channel used on your phone. You can view the code and channel your phone is currently set to on the MOTOtalk home screen.
69MOTOtalkTMFor code calls, all parties must be on the same channel and code. For private MOTOtalk calls, the person you are calling must be in MOTOtalk and on the same channel to receive your call.Note: When making a code call, all parties that are on your code and channel can hear your conversation.setting channels and codesTo set a channel:1From the MOTOtalk home screen, press K under Edit.2Scroll to Channel.3Press K under Edit.4Select a channel.5When you are finished, press K under Back to return to the MOTOtalk home screen.To set a code:1From the MOTOtalk home screen, press K under Edit.2Scroll to Code.3Press K under Edit.4Select a code.5When you are finished, press K under Back to return to the MOTOtalk home screen.making code callsTo make a code call:1From the MOTOtalk home screen or the channel and code edit screen, press and hold the PTT button. Transmit appears on the first line of display. Begin speaking after your phone emits the MOTOtalk tone.
70MOTOtalkTMNote: The MOTOtalk tone consists of 4 rapid beeps.2Release the PTT button to listen.If you receive an error message:•No one is on your channel or code.•You are out of range.receiving code callsWhen you receive a code call, Receive will appear on the display. After hearing the MOTOtalk tone, you have 6 seconds to reply before the call times out.To reply to the call, press the PTT button.Note: An incoming MOTOtalk call can be terminated at any time by pressing @.receiving all MOTOtalk callsIf you set the code to Receive All, your phone can receive MOTOtalk transmissions from any phone that is set to the same channel, regardless of the code (1-15). When you receive transmissions with the code set to Receive All, the code that the transmission was received on will replace Receive All on the display. Note: You cannot initiate a code call when the code is set to Receive All.To set the code to Receive All:1From the MOTOtalk home screen, press K under Edit.2Scroll to Code.3Press K under Edit.4Select Receive All.5When you are finished, press K under Back to return to the MOTOtalk home screen.To reply to a call with the code set to Receive All:
71MOTOtalkTM•Press the PTT button.private MOTOtalk callsIf you want to have a private conversation without other parties listening in, you can make a private MOTOtalk call. The person you are calling must be in MOTOtalk and set to the same channel to receive your call.private onlyTo set MOTOtalk to ignore code calls, so that you only make or receive private MOTOtalk calls, set your code to Pvt Only.To set the code to Pvt Only:1From the MOTOtalk home screen, press K under Edit.2Scroll to Code.3Press K under Edit.4Select Pvt Only.5When you are finished, press K under Back to return to the MOTOtalk home screen.making a private MOTOtalk call1Enter the PTN of the person you want to call on your channel. If the PTN is more than 10-digits, enter the last 10-digits of the PTN, or scroll to a number or name in Contacts or the Recent Calls List.2Press and hold the PTT button. Begin speaking after your phone emits the MOTOtalk tone.3Release the PTT button to listen.The number or name of the person you are calling will appear in the display.If you receive an error message:•The PTN you entered is invalid.
72MOTOtalkTM•The person that you are trying to reach is in network mode.•The person that you are trying to reach is set to a different channel.•The person that you are trying to reach is out of range.receiving a private MOTOtalk callThe number or name of the person who is calling will appear in the display.To reply, press the PTT button.ending code calls and private MOTOtalk callsCode calls and private MOTOtalk calls will end automatically after 6 seconds of inactivity. The MOTOtalk home screen will display.Note: A private or code MOTOtalk call can be interrupted during the 6 second idle time by another code call or private call.making emergency calls while in MOTOtalkTM modeIf you attempt to make an Emergency 911 call while in MOTOtalk mode, your phone will automatically exit MOTOtalk mode and attempt to find a network signal. If you are out of network coverage your phone will not be able to make an emergency 911 cellular call until you go back into the network coverage area. You must wait until the phone reconnects to the network before attempting to make an emergency 911 cellular call.
73MOTOtalkTMsetup optionsYou can set up MOTOtalk options on the MT Options screen. You can access this screen in both network and MOTOtalk modes.To access setup options:1Press / > MOTOtalk or MT Options.2Select Setup.You can set the following MOTOtalk options:•Direct Launch: Launch directly into MOTOtalk when you select MOTOtalk from the main menu. •State Tone: Have an alert sound notify you that you have used MOTOtalk for a specified interval.using direct launchTo set your phone to launch MOTOtalk when you select MOTOtalk from the main menu:1From the Setup screen, scroll to Direct Launch and press r.2Select On.Note: If Direct Launch is set to On, the MOTOtalk setup options will be unavailable from the main menu. However, you can still access setup options while in MOTOtalk by pressing / and selecting > MT Options > Setup.To turn off Direct Launch:1From the Setup screen, scroll to Direct Launch and press r.2Select Off.MT Options will now display when you select MOTOtalk from the main menu.using state toneTo set your phone to alert you after you have used MOTOtalk for a specified interval:
74MOTOtalkTM1From the Setup screen, scroll to State Tone and press r.2Select the interval after which you want the tone to sound.For example, if you select 1 hour, you will be notified every hour that you are in MOTOtalk.To turn off State Tone:1From the Setup screen, scroll to State Tone and press r.2Select Off.
75customizecustomizering tonesTo set the ring tone your phone makes when you receive phone calls, call alerts, message notifications, pictures sent using Send via PTT or Datebook reminders:Find it: / > Ring Tones1Make sure Vibrate All is set to Off.2Scroll through the list of ring tones and select the one you want to assign. Vibrate sets your phone to vibrate instead of making a sound. Silent sets your phone to neither vibrate nor make a sound.3Select the features you want to assign the ring tone to.4When you are finished, press K under Done.Note: This icon , appears on the display if you set your phone to Silent. This icon 5 appears on the display if you set the phone to Vibrate All.set your phone to vibrateYou can set your phone to vibrate for all calls and alerts.Find it: / > Ring Tones > Vibrate AllSet this option to On or Locked.Setting this option to On lets you turn Vibrate All off by pressing the up volume control. Setting this option to Locked requires you to press and hold the up volume control to turn Vibrate All off.
76customizeThe Locked option helps prevent you from accidentally turning Vibrate All off.To set Vibrate All to On or Locked using the volume controls: Press the volume controls to turn down the volume as far as possible to set Vibrate All to On. Continue to hold the down volume control to set Vibrate All to Locked.To set your phone to vibrate instead of making a sound for some features but not others:Find it: / > Ring Tones1Make sure Vibrate All is set to Off.2Select Vibrate from the list of ring tones.3Select the features you want to set to make no sound.4When you are finished, press K under Done.backlightSet the amount of time that the display and java apps. backlights remain on, or turn off the backlight feature to extend battery life.Find it: / > u > Display/Info > BacklightwallpaperSet a previously saved photo or picture as a wallpaper (background) image on your phone’s display screen or throughout all menu screens.Find it: / > u > Display/Info > Wallpaper1Select Wallpaper.2Scroll through the list of pictures and press r to select a picture.You can set the wallpapers to change automatically after a certain period of time by turning on the Auto Cycle feature located in the
77customizeWallpaper menu. You can select from 5 minutes, 15 minutes, 1 hour, 8 hours, Daily, or Startup.hide or show locationYour phone has a location feature for use in connection with location-based services that may be available in the future.Turning Location On will allow the network to detect your position using GPS technology, making some applications and services easier to use. Turning Location off will disable the GPS location function for all purposes except 911, but will not hide your general location based on the cell site serving your call. No application or service may use your location without your request or permission. GPS-enhanced 911 is not available in all areas.set your privacy optionsFind it: / > GPS > PrivacySelect from the following options:optionRestrictedNo Java or similar software applications may view the location of your phone. However, location information may still be available to the phone’s owner, fleet manager, or account administrator.UnrestrictedAll applications may view the location of your phone, without notifying you.
78customizechange GPS PINWhen you receive your phone, your GPS PIN is 0000. To change your GPS PIN press / > u > Security > Change Passwords > GPS PIN. Enter the current GPS PIN and enter the new four-to-eight digit GPS PIN. Re-enter the new four- to eight-digit GPS PIN to confirm.Ask AccessWhen an application attempts to view the location of your phone, you will be prompted to give permission. However, location information may still be available to the phone’s owner, fleet manager, or account administrator.option
Legal and Safety79Legal and SafetySafety and General InformationThis section contains important information on the safe and efficient operation of your mobile device. Read this information before using your integrated multi-service portable radio.*Exposure to Radio Frequency (RF) EnergyYour mobile device contains a transmitter and receiver. When it is ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits.Your mobile device is designed to comply with local regulatory requirements in your country concerning exposure of human beings to RF energy.Portable Radio Product Operation and EME ExposureYour Motorola radio product is designed to comply with the following national and international standards and guidelines regarding exposure of human beings to radio frequency electromagnetic energy (EME):•United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J.•American National Standards Institute (ANSI) / Institute of Electrical and Electronics Engineers (IEEE). C95. 1-1992.•Institute of Electrical and Electronics Engineers (IEEE). C95. 1-2005 Edition.*•International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998.•Ministry of Health (Canada). Safety Code 6. Limits of Human Exposure to Radio frequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999.•Australian Communications Authority Radio communications (Electromagnetic Radiation - Human Exposure) Standard 2003.•ANATEL, Brazil Regulatory Authority, Resolution 303 (July 2, 2002) “Regulation of the limitation of exposure to * The information provided in this document supersedes the general safety information in user’s guides published prior to May 1, 2006
80Legal and Safetyelectrical, magnetic, and electromagnetic fields in the radio frequency range between 9 kHz and 300 GHz.” “Attachment to Resolution 303 from July 2, 2002." Operational PrecautionsFor optimal mobile device performance, and to be sure that human exposure to RF energy does not exceed the guidelines set forth in the relevant standards, always follow these instructions and precautions.Phone OperationWhen placing or receiving a phone call, hold your mobile phone as you would a landline telephone. Speak directly into the microphone.Two-way radio operationYour radio product has been designed and tested to comply with national and international standards and guidelines regarding human exposure to RF electromagnetic energy, when operated in the two-way mode (at the face, or at the abdomen when using an audio accessory) at usage factors of up to 50% talk/50% listen.Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the PTT button. To receive calls, release the PTT button. Transmitting 50% of the time or less, is important because this radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).When using your radio product as a traditional two-way radio, hold the radio product in a vertical position with the microphone one to two inches (2.5 to 5 cm) away from the lips.If you wear the mobile device on your body, always place the mobile device in a Motorola approved clip, holder, holster, case or body harness. If you do not use a body-worn accessory supplied or approved by Motorola and are not using the mobile device in the intended use positions along side the head in the phone mode or in front of the face in the two-way radio mode, or if you hang your device from a lanyard around your neck, keep the device at least 2.5 centimeters (1 inch) from your body when transmitting.Approved AccessoriesFor a list of approved Motorola accessories call 1-800-453-0920, or visit our website at www.motorola.com/phoneaccessories.RF Energy Interference/CompatibilityNearly every electronic device is subject to RF energy interference from external sources if inadequately shielded, designed or otherwise configured for RF energy compatibility. In some circumstances your mobile device may cause interference with other devices.
Legal and Safety81Follow Instructions to Avoid Interference ProblemsTurn OFF your mobile device in any location where posted notices instruct you to do so.In an aircraft, turn off your mobile device whenever instructed to do so by airline staff. If your mobile device offers an airplane mode or similar feature, consult airline staff about using it in flight.Implantable Medical DevicesIf you have an implantable medical devices, such as a pacemaker or defibrillator, consult your physician before using this mobile device.Persons with implantable medical devices should observe the following precautions:•ALWAYS keep the mobile device more than 20 centimeters (8 inches) from the implantable medical device when the phone is turned ON.•DO NOT carry the mobile device in the breast pocket;•Use the ear opposite the implantable medical device to minimize the potential for interference.•Turn OFF the mobile device immediately if you have any reason to suspect that interference is taking place.Read and follow the directions from the manufacturer of your implantable medical device. If you have any questions about using your mobile device with your implantable medical device, consult your health care provider.Hearing AidsSome phones may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer or physician to discuss alternatives.Other Medical Devices and Health Care FacilitiesIf you use any other personal medical devices, consult your physician or the manufacturer or your device to determine if it is adequately shielded from RF energy. Turn off your radio product when instructed to do so in hospitals or health care facilities that may be using equipment that is sensitive to external RF energy.Caring for the Environment by RecyclingThis symbol on a Motorola product means the product should not be disposed of with household waste.Disposal of your Mobile Device and AccessoriesPlease do not dispose of mobile devices or electrical accessories (such as chargers, headsets, or batteries) with your household waste. These items should be disposed of in accordance with the national collection and recycling schemes operated by your local or
82Legal and Safetyregional authority. Alternatively, you may return unwanted mobile devices and electrical accessories to any Motorola Approved Service Center in your region. Details of Motorola approved national recycling schemes, and further information on Motorola recycling activities can be found at: www.motorola.com/recyclingDisposal of your Mobile Device Packaging and User’s GuideProduct packaging and user’s guides should only be disposed of in accordance with national collection and recycling requirements. Please contact your regional authorities for more details.Driving PrecautionsThe use of wireless phones while driving may cause distraction. Discontinue a call if you can’t concentrate on driving.Additionally, the use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products.Responsible driving practices can be found in the “Smart Practices While Driving” section (see page 95).Operational WarningsObey all posted signs when using Mobile devices in public areas.Potentially Explosive AtmospheresAreas with potentially explosive atmospheres are often but not always posted, and can include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, or areas where the air contains chemicals or particles, such as grain, dust or metal powders.When you are in such area, turn off your handset, and do not remove, install, or charge batteries unless it is a radio product type especially qualified for use in such areas as “Intrinsically Safe” (for example, Factory Mutual, CSA, or UL approved). In such areas, sparks can occur and cause an explosion or fire.Symbol KeyYour battery, charger, or portable radio may contain symbols, defined as follows:Symbol DefinitionImportant safety information follows.Do not dispose of your battery or phone in a fire.032374o032376o
Legal and Safety83Batteries and ChargersCaution: Improper treatment or use of batteries may present a danger of fire, explosion, leakage, or other hazard. For more information, see the “Battery Use and Battery Safety” section in this user’s guide.Keep Your Mobile Device and Its Accessories Away from Small ChildrenThese products are not toys and may be hazardous to small children. For example:•A choking hazard may exist for small, detachable parts.•Improper use could result in loud sounds, possibly causing hearing injury.•Improperly handled batteries could overheat and cause a burn.Glass PartsSome parts of your mobile device may be made of glass. This glass could break if the product is dropped on a hard surface or receives a substantial impact. If glass breaks, do not touch or attempt to remove. Stop using your mobile device until the glass is replaced by a qualified service center.Seizures/BlackoutsSome people may be susceptible to epileptic seizures or blackouts when exposed to flashing lights, such as when playing video games. These may occur even if a person has never had a previous seizure or blackout.If you have experienced seizures or blackouts, or if you have a family history of such occurrences, please consult with your physician before playing video games or enabling a flashing-lights feature (if available) on your mobile device.Your battery or phone may require recycling in accordance with local laws. Contact your local regulatory authorities for more information.Do not throw your battery or phone in the trash.Your phone contains an internal lithium ion battery.Do not let your battery, charger, or phone get wet.Listening at full volume to music or voice through a headset may damage your hearing.Symbol Definition032375o032378oLi Ion BATT
84Legal and SafetyDiscontinue use and consult a physician if any of the following symptoms occur: convulsion, eye or muscle twitching, loss of awareness, involuntary movements, or disorientation. It is always a good idea to hold the screen away from your eyes, leave the lights on in the room, take a 15-minute break every hour, and stop use if you are very tired.Caution About High Volume UsageWarning: Warning: Exposure to loud noise from any source for extended periods of time may affect your hearing. The louder the volume sound level, theless time is required before your hearing could be affected. To protect your hearing:•Limit the amount of time you use headsets or headphones at high volume.•Avoid turning up the volume to block out noisy surroundings.•Turn the volume down if you can’t hear people speaking near you.If you experience hearing discomfort, including the sensation of pressure or fullness in your ears, ringing in your ears, or muffled speech, you should stop listening to the device through your headset or headphones and have your hearing checked.For more information about hearing, see our Web site at www.motorola.com/hearingsafety (in English only).Repetitive MotionWhen you repetitively perform actions such as pressing keys or entering finger-written characters, you may experience occasional discomfort in your hands, arms, shoulders, neck, or other parts of your body. If you continue to have discomfort during or after such use, stop use and see a physician.Service and RepairsIf you have questions or need assistance, we’re here to help.Go to www.motorola.com/support, where you can select from a number of customer care options. You can also contact the Motorola Customer Support Center at 1 (800) 453-0920 (United States), 1 (877) 483-2840 (TTY, TDD United States for hearing impaired).Export Law AssurancesThis product is controlled under the export regulations of the United States of America and Canada. The Governments of the United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs and International Trade.
Legal and Safety85Battery Use and Safety•In very limited circumstances, such as where your phone has been exposed to extreme heat Cool Down message screens will appear. To avoid possible damage to your battery and phone, you should follow these instructions until the phone is within its recommended temperature range. When your phone is in Cool Down mode, only emergency calls may be made.• Motorola recommends you always use Motorola-branded batteries and chargers. The warranty does not cover damage caused by non-Motorola batteries and/or chargers. Caution: Use of an unqualified battery or charger may present a risk of fire, explosion, leakage, or other hazard. Improper battery use, or use of a damaged battery, may result in a fire, explosion, or other hazard.•Battery usage by children should be supervised.• Important: Motorola mobile devices are designed to work best with qualified batteries. If you see a message on your display such as Invalid Battery or Unable to Charge, take the following steps:•Remove the battery and inspect it to confirm it bears a Motorola “Original Equipment” hologram; •If there is no hologram, the battery is not a qualified battery;•If there is a hologram, replace the battery and retry charging it;•If the message remains, contact a Motorola Authorized Service Center.•When storing your battery, keep it in a cool, dry place.•It is normal over time for battery life to decrease, and for the battery to exhibit shorter runtime between charges or require more frequent or longer charging times.Important: Handle and store batteries properly to avoid injury or damage. Most battery issues arise from improper handling of batteries, and particularly from the continued use of damaged batteries.DON’Ts• Don’t disassemble, crush, puncture, shred, or otherwise attempt to change the form of your battery.• Don’t let the phone or battery come in contact with water. Water can get into the phone’s circuits, leading to corrosion. If the phone and/or battery get wet, have them checked by your carrier or contact Motorola, even if they appear to be working properly.• Don’t allow the battery to touch metal objects. If metal objects, such as jewelry, stay in prolonged contact with the battery contact points, the battery could become very hot.
86Legal and Safety• Don’t place your battery near a heat source. Excessive heat can damage the phone or the battery. High temperatures can cause the battery to swell, leak, or malfunction. Therefore:•Do not dry a wet or damp battery with an appliance or heat source, such as a hair dryer or microwave oven.•Avoid leaving your phone in your car in high temperatures.DOs• Do avoid dropping the battery or phone. Dropping these items, especially on a hard surface, can potentially cause damage.• Do contact your service provider or Motorola if your phone or battery has been damaged from dropping or high temperatures.Important: Use Motorola Original products for quality assurance and safeguards. To aid consumers in identifying authentic Motorola batteries from non-original or counterfeit batteries (that may not have adequate safety protection), Motorola provides holograms on its batteries. Consumers should confirm that any battery they purchase has a “Motorola Original” hologram.Motorola recommends you always use Motorola-branded batteries and chargers. Motorola mobile devices are designed to work with Motorola batteries. If you see a message on your display such as Invalid Battery or Unable to Charge, take the following steps:•Remove the battery and inspect it to confirm that it has a “Motorola Original” hologram;•If there is no hologram, the battery is not a Motorola battery;•If there is a hologram, replace the battery and retry charging it;•If the message remains, contact a Motorola authorized service center.Important: Motorola’s warranty does not cover damage to the phone caused by non-Motorola batteries and/or chargers.Warning: Use of a non-Motorola battery or charger may present a risk of fire, explosion, leakage, or other hazard.Proper and safe battery disposal and recycling: Proper battery disposal is not only important for safety, it benefits the environment. Consumers may recycle their used batteries in many retail or service provider locations. Additional information on proper disposal and recycling may be found on the Web:• www.motorola.com/recycling• www.rbrc.org/call2recycle/ (in English only)Disposal: Promptly dispose of used batteries in accordance with local regulations. Contact your local recycling center or national recycling organizations for more information on how to dispose of batteries.Warning: Never dispose of batteries in a fire because they may explode.
Legal and Safety87Battery ChargingNotes for charging your phone’s battery:•When charging your battery, keep it near room temperature. Never expose batteries to temperatures below 0°C (32°F) or above 45°C (113°F) when charging.•New batteries are not fully charged.•New batteries or batteries stored for a long time may take more time to charge.•Motorola batteries and charging systems have circuitry that protects the battery from damage from overcharging.Specific Absorption RateYour model wireless phone meets the governmentalrequirements for exposure to radio waves.Your mobile device is a radio transmitter and receiver. It is designed and manufactured to not exceed limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government and by the Canadian regulatory authorities. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed for the safety of all persons, regardless of age or health, and to account for any variations in measurements.The exposure standard for mobile devices employs a unit of measurement known as the Specific Absorption Rate (SAR). The SAR limit set by the FCC and by the Canadian regulatory authorities is 1.6 watts per kilogram (W/kg), averaged over one gram of tissue. Tests for SAR are conducted using procedures accepted by the FCC and by Industry Canada with the mobile device transmitting at its highest certified power level in all tested frequencies. Although the SAR is determined at the highest certified power level, the actual SAR level of the mobile device while operating can be below the maximum value. This is because the mobile device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station, the lower the power output.Before a mobile device is available for sale to the public in the U.S. and Canada, it must be tested and certified to the FCC and Industry Canada that it does not exceed the limit established by each government for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) submitted to the FCC and available for review by Industry Canada. The highest SAR value for this mobile device when tested for use at the ear is 1.43 W/kg, and when worn on the body, as described in this guide, is 1.09 W/kg. Body-worn measurements can differ, depending upon available accessories and regulatory requirements. The SAR information includes the Motorola testing
88Legal and Safetyprotocol, assessment procedure, and measurement uncertainty range for this product.While there may be differences between the SAR levels of various mobile devices and at various positions, they meet the governmental requirements for safe exposure. Please note that improvements to this product model could cause differences in the SAR value for later products; in all cases, products are designed to be within the guidelines.Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site:http://www.phonefacts.netor the Canadian Wireless Telecommunications Association (CWTA) Web site:http://www.cwta.caAGPS and Emergency CallsWhen you make an emergency call, your mobile device can use Assisted Global Positioning System (AGPS) satellite signals to tell the emergency response center your approximate location.The AGPS feature has limitations, so always tell the emergency response center your best knowledge of your location. Remain on the phone for as long as the emergency response center instructs you.AGPS might not work for emergency calls, if your local emergency response center does not process AGPS location information. For details, contact your local authorities.If your mobile device cannot find strong AGPS satellite signals, the location of the nearest cell tower in contact with your mobile device is automatically provided to the emergency response center.AGPS Performance Tips•Go outside and away from underground locations, covered vehicles, structures with metal or concrete roofs, tall buildings, and foliage. Indoor performance might improve if you move closer to windows, but some window sun shielding films can block satellite signals.•Move away from radios, entertainment equipment, and other electronic devices that might interfere with or block AGPS satellite signals.AGPS uses satellites controlled by the U.S. government and subject to changes implemented in accordance with the Department of Defense AGPS user policy and the Federal Radio Navigation Plan. These changes might affect AGPS performance.
Legal and Safety89Limited Warranty Motorola Communications Products (International)What Does this Warranty Cover?MOTOROLA warrants the MOTOROLA manufactured iDEN Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:Rechargeable Batteries will be replaced during the applicable warranty period if:•the battery capacity falls below 80% of rated capacity, or•the battery develops leakage.MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA.This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product.MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment if expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, Products Covered Length of CoverageiDEN Subscriber Digital Mobile and Portable UnitsOne (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below.Product Accessories (manufactured by or under license from MOTOROLA).One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below.Batteries. One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below.
90Legal and Safetycoverage, or operation of the system as a whole, or any portion of the system not produced by MOTOROLA, under this warranty.General Provisions:This warranty sets forth the full extent of MOTOROLA’S responsibilities regarding the Product, Repair, replacement or refund of the purchase price, at MOTOROLA’S options, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INLCUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.How to Get Warranty Service:You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service.What This Warranty Does Not Cover:•Defects or damage resulting from use of the Product in other than its normal and customary manner.•Defects or damage from misuse, accident, water, or neglect.•Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.•Breakage or damage to antennas unless caused directly by defects in material workmanship.•A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the audition to the Product of non-MOTOROLA supplied equipment).•Product which has had the serial number removed or made illegible.•Rechargeable batteries if:Any of the seals on the battery enclosure of cells are broken or show evidence of tampering.The damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.
Legal and Safety91•Freight costs to the repair depot.•A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA’S published specifications or the local type acceptance labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA.•Scratches or other cosmetic damage to Product surfaces that does not effect the operation of the Product.•Normal and customary wear and tear.•Exclusion for defects or damage arising from use of the products in connection with non-MOTOROLA equipment.Patent and Software Provisions:MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a patent, and Motorola will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:•That MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;•That MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and•Should the Product or parts become, or in MOTOROLA’S opinion be likely to become, the subject of a claim of infringement of a patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA.MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or sued in connection with the Product or any parts thereof. In no event shall MOTOROLA be liable for any incidental, special or consequential damages arising from any claim of patent infringement or alleged infringement.Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software, such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used
92Legal and Safetyto produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise or rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights.Hearing Aid Compatibility With Mobile PhonesSome Motorola phones are measured for compatibility with hearing aids. If the box for your particular model has “Rated for Hearing Aids” printed on it, the following explanation applies.When some mobile phones are used near some hearing devices (hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference they generate.The wireless telephone industry has developed ratings for some of their mobile phones, to assist hearing device users in finding phones that may be compatible with their hearing devices. Not all phones have been rated. Phones that are rated have the rating on their box or a label on the box.The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices than phones that are not labeled. M4 is the better/higher of the two ratings.T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with a hearing device’s telecoil (“T Switch” or “Telephone Switch”) than unrated phones. T4 is the better/higher of the two ratings. (Note that not all hearing devices have telecoils in them.)Hearing devices may also be measured for immunity to this type of interference. Your hearing device manufacturer or hearing health professional may help you find results for your hearing device. The more immune your hearing aid is, the less likely you are to experience interference noise from mobile phones.Information From the World Health OrganizationPresent scientific information does not indicate the need for any special precautions for the use of mobile phones. If you are concerned, you may want to limit your own or your children’s RF exposure by limiting the length of calls or by using hands-free devices to keep mobile phones away from your head and body.Source: WHO Fact Sheet 193
Legal and Safety93Further information: http://www.who.int./peh-emf.Product RegistrationOnline Product Registration:www.motorola.com/us/productregistrationProduct registration is an important step toward enjoying your new Motorola product. Registering permits us to contact you for product or software updates and allows you to subscribe to updates on new products or special promotions. Registration is not required for warranty coverage.Please retain your original dated sales receipt for your records. For warranty service of your Motorola Personal Communications Product you will need to provide a copy of your dated sales receipt to confirm warranty status.Thank you for choosing a Motorola product.Wireless: The New RecyclableYour wireless phone can be recycled. Recycling your phone reduces the amount of waste disposed in landfills and allows recycled materials to be incorporated into new products.The Cellular Telecommunications Industry Association (CTIA) and its members encourage consumers to recycle their phones and have taken steps to promote the collection and environmentally sound recycling of end-of-life devices.As a phone user, you have an important role in ensuring that this device is recycled properly. When it comes time to give this phone up or trade it in for a new one, please remember that the phone, the charger, and many of its accessories can be recycled. It's easy. To learn more about CTIA's Recycling Program for Used Wireless Devices, please visit us at: http://recycling.motorola.young-america.com/ index.htmlCalifornia Perchlorate LabelSome mobile phones use an internal, permanent backup battery on the printed circuit board that may contain very small amounts of perchlorate. In such cases, California law requires the following label:Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.There is no special handling required by consumers.Patent and Trademark InformationMOTOROLA, the Stylized M Logo and all other trademarks indicated as such herein are trademarks of Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off. © 2009 Motorola, Inc. All rights reserved.Microsoft and Microsoft Internet Explorer are registered trademarks of Microsoft Corporation. T9 is a trademark owned by Tegic Communications. T9® Text Input Patent and Trademark Information.
94Legal and SafetyThis product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541, U.S. Pat. 6,011,554 and other patents pending. Java and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. All other product names or services mentioned in this manual are the property of their respective trademark owners. Software Copyright NoticeMotorola products may include copyrighted Motorola and third party software stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.Privacy and Data SecurityMotorola understands that privacy and data security are important to everyone. Because some features of your mobile device may affect your privacy or data security, please follow these recommendations to enhance protection of your information:• Monitor access—Keep your mobile device with you and do not leave it where others may have unmonitored access. Lock your device’s keypad where this feature is available.• Keep software up to date—If Motorola or a software/application vendor releases a patch or software fix for your mobile device that updates the device’s security, install it as soon as possible.• Erase before recycling—Delete personal information or data from your mobile device prior to disposing of it or turning it in for recycling. For instructions on how to delete all personal information from your device, please contact your local service provider.• Understanding AGPS—To provide location information for emergency calls, certain Motorola mobile devices incorporate Assisted Global Positioning System (AGPS) technology. AGPS technology also can be used in non-emergency applications to track and monitor a user’s location—for example, to provide driving directions. Users who prefer not to permit such tracking and monitoring should avoid using such applications.
Legal and Safety95If you have further questions regarding how the use of your mobile device may impact your privacy or data security, please contact Motorola at privacy@motorola.com, or contact your service provider.Smart Practices While DrivingDrive Safe, Call Smart SMCheck the laws and regulations on the use of phones and their accessories in the areas where you drive. Always obey them. The use of these devices may be prohibited or restricted in certain areas—for example handsfree use only. Go to www.motorola.com/callsmart (in English only) for more information.Your mobile device lets you communicate by voice and data—almost anywhere, anytime, wherever wireless service is available and safe conditions allow. When driving a car, driving is your first responsibility. If you choose to use your phone while driving, remember the following tips:• Get to know your Motorola mobile device and its features such as speed dial and redial. If available, these features help you to place your call without taking your attention off the road.• When available, use a handsfree device. If possible, add an additional layer of convenience to your phone with one of the many Motorola Original handsfree accessories available today.• Position your mobile device within easy reach. Be able to access your phone without removing your eyes from the road. If you receive an incoming call at an inconvenient time, if possible, let your voice mail answer it for you.• Let the person you are speaking with know you are driving; if necessary, suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow, ice, and even heavy traffic can be hazardous.• Do not take notes or look up phone numbers while driving. Jotting down a “to do” list or going through your address book takes attention away from your primary responsibility, driving safely.• Dial sensibly and assess the traffic; if possible, place calls when your car is not moving or before pulling into traffic. If you must make a call while moving, dial only a few numbers, check the road and your mirrors, then continue.• Do not engage in stressful or emotional conversations that may be distracting. Make people you are talking with aware you are driving and suspend conversations that can divert your attention away from the road.• Use your mobile device to call for help. Dial 911 or other local emergency number in the case of fire, traffic
96Legal and Safetyaccident, or medical emergencies (wherever wireless phone service is available).• Use your mobile device to help others in emergencies. If you see an auto accident, crime in progress, or other serious emergency where lives are in danger, call 911 or other local emergency number (wherever wireless phone service is available), as you would want others to do for you.• Call roadside assistance or a special non-emergency wireless assistance number when necessary. If you see a broken-down vehicle posing no serious hazard, a broken traffic signal, a minor traffic accident where no one appears injured, or a vehicle you know to be stolen, call roadside assistance or other special non-emergency wireless number (wherever wireless phone service is available).
97indexindexAaccessories 9active phone line 37advanced calling 143-way calls 14call waiting 14alertset 40, 75turn off 40, 58answer a call 13audio formats 45auto replies 24Bbattery charging 11battery charging indicators 12battery indicator 37battery installation 10Bluetooth 55connect 55send information 57setting your phone 55turning on or off 55Ccallanswer 13any key answer 14end 13make 13call forward 59caller ID 59callsSDG, see SDG callscenter key 9, 41contacts 77edit/delete 16set ringer ID 16Ddatebook 77create events 34receive events via PTT 34setup 35view reminders 34dial a phone number 13dialed calls 58direct launch 73display 36
98indexdraftssee also text messages, drafts 20Eearpiece volume 40emergency number 61end a call 13end key 13Ffrequently asked questionsservice and repairs 84GGPS enabledemergency calls 61GPS, see GPS enabledHhandsfree speaker 41hearing aid 42Hearing Aid Compatibility 92home screen 36Iimage formats 46international calls 61Llow battery message 37Mmain menu 37make a call 13media center 45message centertext messages 22message indicator 37messaging 17modemusing your phone as a 35MOTOtalkcalls, ending 72channels 68channels, setting 69code calls, making 69code calls, receiving 70codes 68codes, setting 69direct launch 73emergency calls 72private MOTOtalk calls 71private only setting 71receiving all calls 70setup options 73state tone 73switching to 68switching to network mode 68talk range 68
99indexNnavigation key 9, 41Oone touch PTT 53optional accessory 9optional feature 9Ppacket data 37phone number 17power key 13private callsanswer 15call alerts 15make 14receive a call alert 15PT Manager 54PTX features 46Rradio frequency 79received calls 58recent calls 58recycling 93redial 59ring style indicator 37ring style, setting 40ring tonesoff 75setting 75vibrate 75, 76ring tones, setting 75ringer volume 40Ssafetyradio frequency 79RF energy interference 80safety information 79safety tips 95SDG callslists, adding numbers 63lists, creating 63lists, deleting 64lists, remove members 64lists, save entries 54make call 65starting 65security 44Selective Dynamic Group Calls, see SDG callssend key 13signal strength indicator 36SIM card 10change SIM PIN 44enable SIM PIN 44soft keys 36speaker 37speed dial 62state tone 73store your number 17
100indexTtext entry 37alpha method 39word method 38text messages 17, 35creating 17deleting 27drafts 20memory 28message center 22receiving 21resend messages 27sending 17sent messages 27Vvoice names 60voice mail 62message indicator 62receiving 62setting up 62volume 40Wwallpaper 76WHO information 92Yyour phone number 17
www.motorola.comNNTN7906A@NNTN7906A@xxxxxxxx xx xx JAN/10Printed in USA

Navigation menu