Motorola Mobility T6FB1 Bluetooth Headset User Manual 9495A89o Front

Download:
Mirror Download [FCC.gov]
Document ID	656272
Application ID	XxQY15Glbc8Po8mr8Etz9A==
Document Description	User Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.71kB (171426 bits)
Date Submitted	2006-05-10 00:00:00
Date Available	2006-05-10 00:00:00
Creation Date	2006-02-06 14:24:42
Producing Software	Adobe PDF library 7.77
Document Lastmod	2006-04-05 10:58:56
Document Title	9495A89o_Front
Document Creator	Adobe Illustrator CS2

BEFORE YOU
BEGIN
CHARGE
Your Headset's Battery
START BLUETOOTH
FEATURE
PAIR
Your Headset
Before using this product, read the Important Safety and Legal
Information pamphlet and follow its instructions.
H5
Bluetooth®
Handsfree Headset
Get Connected in
4 Quick Steps
Take a moment before you get started to
familiarize yourself with your new
H5 Headset.
1 - CHARGE
2 - START
BLUETOOTH
FEATURE
3 - PAIR
4 - TEST AND
USE
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Earpiece
Speaker
Volume
Buttons
Call
Button
Microphone
(inside
earpiece)
Indicator
Light
PAIR CONTINUED
Your Phone
For most Motorola phones:
1 On your Motorola phone, press M (Menu ) >
Settings > Connection > Bluetooth Link >
Handsfree > Look for Devices.
The phone lists Bluetooth devices it finds.
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
© Motorola, Inc. 2006.
2 Select Motorola H5.
3 Select OK or Yes to pair your headset with
supply into charger port
on charger base. The
charger battery indicator
light turns on (
).
Headset
Battery
Indicator
Light
Charger
Battery
Indicator
Charger Light
Plug
2 Insert headset snugly
into charger base.
The headset battery
indicator light turns on
) to indicate the
headset is charging.
It may take up to 1
minute for the indicator
light to turn on. When
headset's battery is
fully charged (about 2
hours), the headset
battery indicator light
turns off.
When charged,
remove headset
from charger base.
Note: The charger base
battery remains charging
while plugged into the
power supply.
Note: Headset is not functional while charging.
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
Guide Number: 6809495A89-O
Headset
1 Plug Motorola power
your phone.
Enter the passkey: 0000
Select OK.
When your headset successfully pairs with
your phone, the indicator light changes from
steadily lit to flashing.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
TEST AND USE
Your phone and headset are now paired and
ready to make and receive calls.
To make a call:
1 Place the headset in your ear. The eartip
should be inserted so that the headset
feels comfortable and forms a seal in the
ear.
2 On your phone, dial the number you want
to call and press the SEND key.
3 If your phone and headset are successfully
paired, you will hear ringing on the headset.
After you have successfully paired your
phone and headset, you don't need to
repeat these steps. For daily use, ensure
that your headset is turned ON and that
your phone's Bluetooth feature is ON.
Your Phone
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones:
1 Press M (Menu ) > Settings > Connection >
Bluetooth Link > Setup.
2 Scroll to Power.
3 Select Change.
4 Scroll to On.
5 Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn the feature off.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
Before you can use your headset, you must pair
(link) it with your phone.
Step A - PUT THE HEADSET IN PAIRING
MODE
Indicator
Light
Call
Button
1 Ensure the headset is turned off (indicator
light not blinking).
Note: See "Turning On and Off" on the reverse side of this
guide for details on turning off your headset.
2 Press and hold the Call button for 6 to 10
seconds. The indicator light will initially flash,
but continue to hold down the button until the
indicator light is steadily lit.
If the indicator light is flashing or not steadily
lit when releasing the button, repeat both
steps 1 and 2 on this page.
USING YOUR H5
TROUBLESHOOTING
See
Features and
Functions Guide
on the reverse side
for information on
using your H5.
My phone doesn't find my headset.
Make sure the indicator light on your headset is
on and steady when your phone is searching for
devices (see step 3).
My headset worked before but now it's not
working.
Make sure your phone is on and the Bluetooth
feature is turned on in your phone (see step 2).
If the Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature (see step 2) and
pair your phone and headset again (see step
3).
Support.
If you need more help, contact us at
1- 877-MOTOBLU.
FOR DETAILS ABOUT YOUR HANDSFREE
DEVICE
See the user’s guide or visit us at
www.hellomoto.com/bluetooth and click
Support.
TURNING ON AND OFF
H5
Bluetooth®
Handsfree Headset
To turn your headset on, press and hold
the Call button until the indicator light
flashes.
To turn your headset off, press and hold
the Call button until the indicator light
flashes rapidly and then turns off.
To conserve battery power, turn off your
headset when you don't plan to use it for
a while.
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side to
complete initial setup of
your H5.
INSTALLING EARTIP
Your headset is supplied with both flanged and
foam eartips. To install these eartips:
Indicator
Light
MAKING CALLS CONTINUED
Function
Action
Toggle between two
active calls
Press and hold
the Call button until
you hear a medium
beep
Join a 3-way call
Press and hold
both Volume buttons
until you hear a
medium beep
Put an active call on
hold or resume a call
on hold
Press and hold the
Call button until you
hear a medium beep
Transfer a call from the
phone to the headset
Tap the Call button
Disable or enable the
indicator light
Press and hold
both Volume
buttons until you
hear a low beep
Mute or unmute a call
Tap both Volume
buttons
Note: Some features are phone/network dependent.
FLANGED EARTIP:
1 Pull upward slightly on
2 Place the earpiece
1 Pull back largest
speaker into your ear.
flange on eartip.
The eartip should form a
comfortable seal in your
ear.
2 Twist eartip onto
earpiece starting at
an angle and pushing
onto headset.
FOAM EARTIP:
1 Roll foam between thumb
Twist eartip onto
earpiece starting at an
angle and pushing
onto headset.
INDICATOR LIGHTS
Indicator lights provide information about your
headset (and charger base) status.
Charger Base
Indicator
Status
Charger Battery
(On) Charging
(Off) Charging complete
Headset Battery
(On) Charging
(Off) Charging complete
Headset
Indicator
Off
On (steady)
10 rapid flashes
Slow pulse
Quick flash
MAKING CALLS
Function
Action
Make a voice dial call
Tap the Call button
and speak the name
after the tone
End a call
Tap the Call button
Receive a call
Tap the Call button
Reject a call
Press and hold the
Call button until you
hear a medium beep
Redial last call
Press and hold the
Call button until you
hear a medium beep
Answer a second
incoming call
Press and hold the
Call button until you
hear a medium beep
(places first call on
hold)
top of your ear.
FLANGED EARTIP:
FOAM EARTIP:
Call
Button
WEARING HEADSET
Status
Power off
Pairing mode
Pairing successful
Connected (on a call)
Standby (not on call)
Note: After 5 minutes of inactivity, the light stops flashing to
conserve power, but the headset remains in standby mode.
and forefinger to
compact.
Pull upward slightly on top
of your ear.
Place the earpiece
speaker into your ear and
hold for 5 seconds while
The eartip should form a comfortable seal in
your ear.
AUDIO TONES
The audio tones provide information about your
headset's status.
Audio Tone
Single high tone when
pressing Volume button
Five rapid high tones
repeated every 60 sec.
No audio indications;
deteriorating quality
Ring tone
Single very high
tone
Single high tone
Single medium tone
Single low tone
Headset Status
Volume at minimum
or maximum
Low battery
Out of range
Incoming call
All calls ended
Entering pairing mode
Tapping Call button or
both Volume buttons
Pressing Call button
or both Volume buttons
Pressing and holding
Call button or both
Volume buttons
Note: Your H5 supports both Handsfree and Headset Profiles.
Accessing call functions depends upon which profile your
phone supports. See your phone's user's guide for more
information.
AUDIO TONES
Audio Tone
Single high tone
repeated every 5 sec.
Two ascending tones
Two descending tones
Four ascending tones
Four descending tones
CONTINUED
Headset Status
Phone network not
available
Mute enabled
Mute disabled
Headset powering on
Headset powering off
VOLUME BUTTONS
Volume button orientation can be changed on
your headset as follows:
1 Turn your headset off
2 Press both Call button and the Volume button
you want to assign as the "volume up" button
until the indicator light flashes twice. The
headset power turns on.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2006:02:06 14:24:42-05:00
Creator                         : Adobe Illustrator CS2
Modify Date                     : 2006:04:05 10:58:56+02:00
About                           : uuid:0531e25f-c1cb-46e4-a463-25fe53042705
Producer                        : Adobe PDF library 7.77
Creation Date                   : 2006:02:06 14:24:42-05:00
Mod Date                        : 2006:04:05 10:58:56+02:00
Creator Tool                    : Adobe Illustrator CS2
Metadata Date                   : 2006:04:05 10:58:56+02:00
Thumbnail Width                 : 256
Thumbnail Height                : 156
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 3889 bytes, use -b option to extract)
Document ID                     : uuid:D3753B334E97DA11AA0F8A0ED8E856A5
Instance ID                     : uuid:5381932d-c9f0-4ace-a223-cb0aa3cc533f
Derived From Instance ID        : uuid:3005080B8996DA11BD75EC2DAA12DF28
Derived From Document ID        : uuid:12A83ED06A96DA11BD75EC2DAA12DF28
Format                          : application/pdf
Title                           : 9495A89o_Front
Page Count                      : 2

EXIF Metadata provided by EXIF.tools