Motorola Solutions 89FT5870 Portable 2-way radio User Manual

Motorola Solutions, Inc. Portable 2-way radio

Contents

User Manual

Download: Motorola Solutions 89FT5870 Portable 2-way radio User Manual
Mirror Download [FCC.gov]Motorola Solutions 89FT5870 Portable 2-way radio User Manual
Document ID2596041
Application IDqOf3zYjvF/RtmsEJ8QNtoA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize401.44kB (5017998 bits)
Date Submitted2015-04-24 00:00:00
Date Available2015-04-28 00:00:00
Creation Date2015-03-09 18:42:56
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2015-03-12 13:02:32
Document TitleDLR Series Two Way Radios User Guide [P/N# MN001132A01 Rev. AA]
Document CreatorFrameMaker 8.0
Document Author: Motorola Solutions, Inc.

Two-Way Radios
User Guide
DLR1020, DLR1060 models
CONTENTS
12
13
14
15
16
16
17
18
CONTENTS
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Product Safety . . . . . . . . . . . . . . . . . . . . . . . .3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .4
Package Contents . . . . . . . . . . . . . . . . . . . . . .4
FCC Licensing Information . . . . . . . . . . . . .6
Batteries and Chargers Safety
Information. . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operational Safety Guidelines. . . . . . . . . . . . .8
Radio Overview . . . . . . . . . . . . . . . . . . . . . . .9
Parts Of The Radio . . . . . . . . . . . . . . . . . . . . .9
Power Button . . . . . . . . . . . . . . . . . . . . .10
Programmable Top Button . . . . . . . . . . .10
Volume Control (+/-) Button . . . . . . . . . .10
Audio Accessory Connector . . . . . . . . . .10
Microphone . . . . . . . . . . . . . . . . . . . . . . .10
Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .10
Tx/Rx Indicator LED . . . . . . . . . . . . . . . .10
Push-to-Talk (PTT) Button . . . . . . . . . . .10
Menu Button . . . . . . . . . . . . . . . . . . . . . .10
The Lithium-Ion (Li-Ion) Battery . . . . . . .10
Battery Features . . . . . . . . . . . . . . . . . . . . . .12
About the Li-Ion Battery . . . . . . . . . . . . .
Battery Recycling and Disposal . . . . . . .
Installing the Lithium-Ion
(Li-Ion) Battery . . . . . . . . . . . . . . . . . .
Removing the Lithium-Ion
(Li-Ion) Battery . . . . . . . . . . . . . . . . . .
Holster . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply, Adaptor and Drop-in
Tray Charger . . . . . . . . . . . . . . . . . . .
Battery Life Information . . . . . . . . . . . . .
Charging the Battery . . . . . . . . . . . . . . .
Drop-in Tray Charger Charge
Status Indicators . . . . . . . . . . . . . . . .
Drop-in Tray Charger Battery State of
Charge Indications . . . . . . . . . . . . . . .
Estimated Charging Time . . . . . . . . . . .
Multi-Unit Charger Charge Status
Indicators . . . . . . . . . . . . . . . . . . . . . .
Multi-Unit Charger Battery State
of Charge Indications . . . . . . . . . . . . .
Getting Started . . . . . . . . . . . . . . . . . . . . . .
Turning radio ON/OFF . . . . . . . . . . . . . . . . .
Adjusting Volume . . . . . . . . . . . . . . . . . . . . .
20
21
22
24
25
27
27
27
English
CONTENTS
English
Checking Battery Status . . . . . . . . . . . . . . . .27
Selecting a Channel . . . . . . . . . . . . . . . . . . .28
Programmable Top Button Options. . . . . . . .28
Programmable Top Button Options: . . . .28
Transmitting and Receiving. . . . . . . . . . . . . .29
Talking to a Group in a Channel . . . . . . .29
Private Reply . . . . . . . . . . . . . . . . . . . . . . . . .29
Private Reply Request . . . . . . . . . . . . . .30
Private Reply Hang Time . . . . . . . . . . . .30
Talking in a Private Mode . . . . . . . . . . . .32
Ending a Private Reply Or Direct Call. . .33
Private Direct Call . . . . . . . . . . . . . . . . . . . . .33
Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .35
Radio Status . . . . . . . . . . . . . . . . . . . . . . . . .36
Advanced Radio Configuration . . . . . . . . .37
Entering Advanced Radio
Configuration. . . . . . . . . . . . . . . . . . . .37
Setting Radio Profile ID (PIN) . . . . . . . . .38
Setting the Maximum Channels . . . . . . .39
Setting the Programmable Top
Button Options . . . . . . . . . . . . . . . . . .39
Setting the Microphone Gain . . . . . . . . .39
Customer Programming
Software (CPS) . . . . . . . . . . . . . . . . . . . . . .
Cloning Radios. . . . . . . . . . . . . . . . . . . . . . .
Cloning with a Multi-Unit
Charger (MUC) . . . . . . . . . . . . . . . . .
Wireless PIN Cloning Radios. . . . . . . . .
CPS and Cloning Cables
(Optional Accessory) . . . . . . . . . . . . .
Cloning Radio using the Radio
to Radio (R2R) Cloning Cable
(Optional Accessory) . . . . . . . . . . . . .
Cloning using the Customer
Programming Software (CPS) . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . .
Use and Care . . . . . . . . . . . . . . . . . . . . . . .
Motorola Limited Warranty for
the United States and Canada . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . .
Audio Accessories . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carry Accessories . . . . . . . . . . . . . . . . . . . .
Software Applications. . . . . . . . . . . . . . . . . .
41
42
42
43
44
45
48
49
52
53
57
57
57
57
57
58
58
PRODUCT SAFETY
Caution
www.motorolasolutions.com/DLR
PRODUCT SAFETY
PRODUCT SAFETY AND RF
EXPOSURE COMPLIANCE
For a list of Motorola-approved batteries and
other accessories, visit the following website
which lists approved accessories:
Before using this product,
read the operating
instructions and RF energy
awareness information
contained in the Product
Safety and RF Exposure
booklet enclosed with your
radio.
ATTENTION!
This radio is restricted to occupational use only
to satisfy FCC RF energy exposure
requirements.
English
INTRODUCTION
INTRODUCTION
Thank you for purchasing the Motorola® DLR
Series Radio. This radio is a product of
Motorola's 80 plus years of experience as a
world leader in the designing and
manufacturing of communications equipment.
The DLR Series radios provide cost-effective
communications for businesses such as retail
stores, restaurants, schools, construction sites,
manufacturing, property and hotel
management and more. Motorola professional
two-way radios are the perfect communications
solution for all of today's fast-paced industries.
Note:
English
Read this user guide carefully to ensure you
know how to properly operate the radio
before use
Business Radios,
Mailstop 1C15, Motorola
8000 West Sunrise Boulevard
Plantation, Florida 33322
PACKAGE CONTENTS
•
Radio
•
Holster
•
Lithium-Ion Battery
•
Power Supply
•
Quick Reference Guide
•
Drop-in Tray Charger with Power Adapter
•
Product Safety & RF Exposure Booklet
For a copy of a large-print version of this user
guide or for product-related questions, contact
INTRODUCTION
1-800-448-6686 in the USA
1-800-461-4575 in Canada
1-888-390-6456 on TTY (Text Telephone)
For product related information, visit us at:
www.motorolasolutions.com/DLR
English
FCC LICENSING
INFORMATION
FCC LICENSING
INFORMATION
English
DLR Series business two-way radios operate in
the license-free 900 MHz ISM Band (902 – 928
MHz) and are subject to the Rules and
Regulations of the Federal Communications
Commission (FCC).
This device complies with part 15 of the FCC
Rules and RSS210 of the Industry Canada.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved
by Motorola may void the user’s authority granted
by the FCC/IC to operate this radio and should not
be made. To comply with FCC/IC requirements,
transmitter adjustments should be made only by or
under the supervision of a person certified as
technically qualified to perform transmitter
maintenance and repairs. Replacement of any
transmitter component (crystal, semiconductor,
etc.) not authorized by the FCC/IC equipment
authorization for this radio could violate FCC/IC
rules.
Note:
Use of this radio outside the country where it
was intended to be distributed is subject to
government regulations and may be
prohibited.
Cet appareil est conforme à la partie 15 des règles
de la FCC / IC . Son fonctionnement est soumis
aux deux conditions suivantes : (1) Ce dispositif
ne doit pas causer d’interférences nuisibles , et
(2) cet appareil doit accepter toute interférence
reçue, y compris les interférences qui peuvent
causer une opération indésirable.
Les changements ou modifications non
expressément approuvés par Motorola peuvent
annuler l'autorisation de l'utilisateur accordée par
la FCC / IC pour opérer cette radio et ne devraient
pas être faits . Pour se conformer aux exigences
de la FCC / IC, les ajustements de l'émetteur
doivent être effectués seulement par ou sous la
supervision d'une personne certifiée en valeur
technique .
3.
and cord, pull by the plug rather than the cord
when disconnecting the charger.
4.
extension cord could result in risk of fire and
electric shock. If an extension cord must be
used, make sure that the cord size is 18AWG
Before using the battery charger, read all the
instructions and cautionary markings on
the charger,
•
the battery, and
•
the radio using the battery
1.
To reduce risk of injury, charge only the
for lengths up to 100 feet (30.48 m), and
16AWG for lengths up to 150 feet (45.72 m).
5.
To reduce risk of fire, electric shock, or injury, do
not operate the charger if it has been broken or
damaged in any way. Take it to a qualified
Motorola service representative.
6.
Do not disassemble the charger; it is not
rechargeable Motorola-authorized batteries.
repairable and replacement parts are not
Other batteries may explode, causing personal
available. Disassembly of the charger may
injury and damage.
2.
An extension cord should not be used unless
absolutely necessary. Use of an improper
This document contains important safety and
operating instructions. Read these instructions
carefully and save them for future reference.
•
To reduce risk of damage to the electric plug
Use of accessories not recommended by
BATTERIES AND CHARGERS
SAFETY INFORMATION
BATTERIES AND
CHARGERS SAFETY
INFORMATION
result in risk of electrical shock or fire.
7.
To reduce risk of electric shock, unplug the
Motorola may result in risk of fire, electric
charger from the AC outlet before attempting
shock, or injury.
any maintenance or cleaning
English
BATTERIES AND CHARGERS
SAFETY INFORMATION
OPERATIONAL SAFETY
GUIDELINES
•
Turn the radio OFF when charging battery.
•
The charger is not suitable for outdoor use. Use
only in dry locations/conditions.
•
Connect charger only to an appropriately fused
and wired supply of the correct voltage (as
specified on the product).
•
Disconnect charger from line voltage by removing
main plug.
•
The outlet to which this equipment is connected
•
In equipment using fuses, replacements must
should be nearby and easily accessible.
comply with the type and rating specified in the
equipment instructions.
•
Maximum ambient temperature around the power
supply equipment must not exceed 40°C (104°F).
•
Power output from the power supply unit must not
exceed the ratings stated on the product label
English
located at the bottom of the charger.
•
Make sure that the cord is located where it will
not be stepped on, tripped over, or subjected to
water, damage, or stress.
RADIO OVERVIEW
PARTS OF THE RADIO
Antenna
Power Button
Tx/Rx
Indicator
LED
Audio Accessory
Connector
Volume/Up-Down
Control Buttons
Menu
Button
PTT (Push-ToTalk) Button
RADIO OVERVIEW
Programmable Top
Button
Microphone
Battery
Speaker
English
Power Button
Tx/Rx Indicator LED
Used to turn the radio ON or OFF.
Used to indicate whether the radio is on
standby, receiving or transmitting.
RADIO OVERVIEW
Programmable Top Button
This Programmable Top button can be
configured by the Programming Mode to initiate
private call, private direct call, call all available
or disable.
Note:
The Programmable Top button must be set
to be configurable in the user menu via CPS
in order to appear in the device user menu.
To respond, press the PTT (Push to Talk) and
WAIT to hear the Talk Permit Tone (a quick
double beep) BEFORE you start speaking.
Hold the radio vertically 1 to 2 inches (2.5cm to
5cm) from mouth when talking. Release the
PTT to listen.
Volume Control (+/-) Button
Menu Button
Used to increase (+), decrease (-) or mute the
volume.
Audio Accessory Connector
Gives access to set up features and allows
navigation through all features while in
Programming Mode.
Used to connect compatible audio accessories.
The Lithium-Ion (Li-Ion) Battery
Microphone
DLR Series comes with a Standard Capacity
Li-Ion battery. Other batteries may be available.
For more information, see “Battery Features”
on page 12.
Speak clearly into the microphone when
sending a message.
Antenna
For models DLR1020 and DLR1060 the
antennas are non-removable.
English
Push-to-Talk (PTT) Button
10
Table 1: DLR Series Radio Specifications
Model
Frequency
Band
Transmit
Power
(Watts)
Number of
Channels
Antenna
DLR1020
ISM 900 MHz
Non-removable
DLR1060
ISM 900 MHz
Non-removable
11
RADIO OVERVIEW
This User Guide covers multiple DLR Series
models, and may detail some features your
radio does not have. The radio’s model is
shown on the back of the radio and provides
the following information:
English
BATTERY FEATURES
RADIO OVERVIEW
DLR Series radios provide the standard
Lithium-Ion
English
Note:
Batteries that come in different capacities
that defines the battery life may be available
in future.
About the Li-Ion Battery
The DLR Series radio comes equipped with a
rechargeable Li-Ion battery. This battery should
be fully charged before initial use to ensure
optimum capacity and performance.
Battery life is determined by several factors.
Among the more critical are the regular
overcharge of batteries and the average depth
of discharge with each cycle. Typically, the
greater the overcharge and the deeper the
average discharge, the fewer cycles a battery
will last. For example, a battery which is
overcharged and discharged 100% several
times a day, lasts fewer cycles than a battery
that receives less of an overcharge and is
12
discharged to 50% per day. Further, a battery
which receives minimal overcharging and
averages only 25% discharge, lasts even
longer.
Motorola batteries are designed specifically to
be used with a Motorola charger and vice
versa. Charging in non-Motorola equipment
may lead to battery damage and void the
battery warranty. The battery should be at
about 77°F (25°C) (room temperature),
whenever possible. Charging a cold battery
(below 50° F [10°C]) may result in leakage of
electrolyte and ultimately in failure of the
battery. Charging a hot battery (above 95°F
[35°C]) results in reduced discharge capacity,
affecting the performance of the radio.
Motorola rapid-rate battery chargers contain a
temperature-sensing circuit to ensure that
batteries are charged within the temperature
limits stated above.
Battery Recycling and Disposal
Many retailers and dealers participate in this
program. For the location of the drop-off facility
closest to you, access RBRC's Internet web
site at:
www.rbrc.com
or call:
1-800-8-BATTERY
This internet site and telephone number also
provides other useful information concerning
recycling options for consumers, businesses
and governmental agencies.
13
RADIO OVERVIEW
Li-Ion rechargeable batteries can be recycled.
However, recycling facilities may not be
available in all areas. Under various U.S. state
laws and the laws of several other countries,
batteries must be recycled and cannot be
disposed of in landfills or incinerators. Contact
your local waste management agency for
specific requirements and information in your
area. Motorola fully endorses and encourages
the recycling of Li-Ion batteries. In the U.S. and
Canada, Motorola participates in the
nationwide Rechargeable Battery Recycling
Corporation (RBRC) program for Li-Ion battery
collection and recycling.
English
Installing the Lithium-Ion (Li-Ion) Battery
RADIO OVERVIEW
1.
Slide the latch at the top of the battery door to the unlock position
and lift up the battery door at the
center recess.
2.
Align the battery contacts with the tabs in the battery compartment. Insert the contact side of the battery first,
3.
Put the battery door back on the radio. Slide the latch to the lock position
then press the battery down to secure in place.
English
14
Removing the Lithium-Ion (Li-Ion) Battery
RADIO OVERVIEW
1.
Turn OFF the radio.
2.
Slide the latch at the top of battery door to the unlock position
and lift up the battery door at the center
recess.
3.
Pull on the battery removal tab until battery is disengaged from battery compartment.
4.
Pull the battery away from radio.
15
English
Power Supply, Adaptor and Drop-in Tray
Charger
1.
The radio is equipped with one Drop-in Tray
Charger and one Power Supply with Adaptor.
For more information, refer to “Chargers” on
page 57.
RADIO OVERVIEW
Holster
Insert the radio into the base of the holster at an
angle. Press the radio against the back of the
holster until the hooks on the holster are
inserted in the top recesses of the battery.
2.
To remove, using the top tab on the holster,
detach the hooks of the holster from the top
recesses of the battery. Slide the radio at an
angle and remove from the holster.
English
16
Battery Life Information
When the Battery Save feature is set to ON (enabled by default), the battery life lasts longer. The
following table summarizes battery life estimations:
Note:
Battery Type
Battery Save OFF
Battery Save ON
Standard
10.0 - 12.0 Hours
TBA
Battery life is estimated based on 5% transmit / 5% receive / 90% standby standard duty cycle.
17
RADIO OVERVIEW
Table 2: Li-Ion Battery Life with Tx Power 1 Watt for DLR1020 and DLR1060
English
Charging the Battery
RADIO OVERVIEW
The DLR Series radio comes with a Standard
Power Supply.
Charging with the Drop-in Tray
Single Unit Charger (SUC)
To charge the battery (with the radio attached),
place it in a Motorola-approved Drop-in Tray
Single Unit Charger or Drop-in Tray Multi Unit
Charger.
1.
Place the Drop-in Tray Charger on a flat
surface.
2.
Insert the connector of the Power Supply into
the charger port on the back of the Drop-in Tray
Charger.
3.
Plug the AC Adaptor into a power outlet.
4.
Insert the radio into the Drop-in Tray Single Unit
Charger with the radio facing the Motorola logo
on the charger as shown in the figure above.
English
18
Note:
When charging a battery attached to the
radio, turn the radio OFF to ensure a full
charge. See “Operational Safety Guidelines”
on page 8 for more information.
Part Number
HKNN4013_
Description
Li-Ion Battery 1800mAh
RADIO OVERVIEW
Charging A Stand-Alone Battery
Table 3: Motorola Authorized Batteries
To charge only the battery - at step 4 on
page 18, insert the battery into the tray, with the
inside surface of the battery facing the front of
the Drop-in Tray Single Unit Charger as shown
above. Align the slots in the battery with the
alignment ribs in the Drop-in Tray Single Unit
Charger.
19
English
Drop-in Tray Charger Charge Status Indicators
Table 4: Charge Status LED Indicator
RADIO OVERVIEW
LED Indication
Charger State
Charger Ready for Use
Single Flash Green
Slow Flash Amber
Fast Flash Red
Waiting to Charge(*)
Battery Fault(**)
Charging
Steady Red
Steady Green
Charged(***)
No Battery in Pocket
LED Off
(*) Battery temperature is too warm or too cold or wrong power voltage is being used.
(**) Normally, re-positioning the battery pack will correct this issue.
(***) Battery is charged to at least 95% threshold of the battery.
English
20
Drop-in Tray Charger Battery State of Charge Indications
Table 5: Battery State of Charge
Battery State of Charge
Flash Red 1 Time
Flash Amber 2 Times
RADIO OVERVIEW
LED Indication
Battery Low
Battery Medium
Battery High
Flash Green 3 Times
If there is NO LED indication:
1.
Check if the radio with battery, or the battery alone, is inserted correctly. (refer to step 4 of "Charging with the
2.
Ensure that the power supply cable is securely plugged into the charger socket using an appropriate AC
3.
Confirm that the battery being used with the radio is listed in Table 3 on page 19.
Drop-in Tray Single Unit Charger (SUC)" on page 18)
outlet and there is power to the outlet.
21
English
Estimated Charging Time
RADIO OVERVIEW
The following table provides the estimated charging time of the battery. For more information, see
“Battery” on page 57.
English
Table 6: Battery Estimated Charging Time
Estimated Charging Time
Charging Solutions
Standard Battery
Standard
22
≤ 3.50 Hours
Charging a Radio and Battery using
a Multi Unit-Charger - MUC (Optional
Accessory)
1.
Place the Multi-Unit Charger on a flat surface.
2.
Insert the power cord plug into the MUC’s dual
3.
Plug the power cord into an AC outlet.
4.
Turn the radio OFF.
5.
Insert the radio or battery into the charging
pin connector at the bottom of the MUC.
RADIO OVERVIEW
pocket with the radio or battery facing away
from the contacts.
Note:
The Multi-Unit Charger (MUC) allows drop-in
charging of up to 12 radios or up to 6 radios
and 6 stand-alone batteries. Batteries can be
charged with the radios or removed and placed
in the MUC separately. Each of the 12 charging
pockets can hold a radio (with or without the
Holster) or battery, but not both.
•
This Multi-Unit Charger clones up to 2 radios (2
Source radios and 2 Target radios). Refer to
“Cloning with a Multi-Unit Charger (MUC)” on
page 42 for more information.
•
More information on the Multi-Unit Charger’s
operation is available in the Instruction Sheets
provided with the MUC. For more information on
the parts and their part numbers, refer to Chapter
“Accessories” on page 57.
23
English
Multi-Unit Charger Charge Status Indicators
Table 7: Charge Status LED Indicator
RADIO OVERVIEW
LED Indication
Charger State
Charger Ready for Use
Single Flash Green
Slow Flash Amber
Fast Flash Red
Waiting to Charge(*)
Battery Fault(**)
Charging
Steady Red
Steady Green
Charged(***)
No Battery in Pocket
LED Off
(*) Battery temperature is too warm or too cold or wrong power voltage is being used.
(**) Normally, re-positioning the battery pack will correct this issue.
(***) Battery is charged to at least 95% threshold of the battery.
English
24
Multi-Unit Charger Battery State of Charge Indications
Table 8: Battery State of Charge
Flash Red 1 Time
Flash Amber 2 Times
Battery State of Charge
RADIO OVERVIEW
LED Indication
Battery Low
Battery Medium
Battery High
Flash Green 3 Times
If there is NO LED indication:
1.
Check if the radio with battery or the battery alone, is inserted correctly (refer to step 5 of "Charging a Radio
and Battery using a Multi Unit-Charger - MUC (Optional Accessory)" on page 23).
2.
Make sure the power cord is securely plugged into the MUC and the appropriate AC outlet. Make sure there
3.
Confirm that the battery being used with the radio is listed in Table 3 on page 19.
is power to the AC outlet.
25
English
RADIO OVERVIEW
Notes
English
26
GETTING STARTED
Note:
TURNING RADIO ON/OFF
To turn ON the radio, press and hold the Power
button until the radio plays the power up tone
and the standby light begins to blink.
To turn the radio OFF, press and hold the
Power button (~3 seconds) until the radio Tx/
Rx Indicator LED turns OFF and power down
tone is heard.
CHECKING BATTERY STATUS
To check the battery status:
ADJUSTING VOLUME
•
Press the (+) button to increase the volume, or
the (-) button to decrease the volume.
Note:
To mute, press and hold the (-) button (~2
seconds) until you hear the voice
announcement “Mute”.
To maximize volume, press and hold the (+)
button (~2 seconds). The volume will fast scroll
up to maximum volume. You will hear the
Do not hold the radio too close to the ear
when the volume is high or when adjusting
the volume
There are 16 increments of volume.
As the (+) / (-) buttons are pressed, you will
hear a beep at the current volume level. If
device is receiving during volume
interaction, received audio will be heard at
the new volume instead of beeps.
Press Menu button until the voice announcement
GETTING STARTED
For the following explanations, refer to “Parts
Of The Radio” on page 9.
volume beeps increment as the volume
increases.
“Battery Level ” is heard, OR
The four levels available for battery status
are : High, Medium, Low and Critical.
To exit battery status checking, press the PTT
button or wait for menu timer to expire. Radio
plays exit menu tone.
27
English
GETTING STARTED
SELECTING A CHANNEL
To select a channel, press Menu button until
the voice announcement “Channel ,
to change press + or -” is heard.
Press (+) or (-) buttons to select the desired
channel. An audible voice indicates the
selected channel.
To exit Channel Change, press the PTT button
or wait for Menu timer to expire.
PROGRAMMABLE TOP BUTTON OPTIONS
The Programmable Top button can be
configured to allow multiple calling options.
Upon pressing the Programmable Top button,
you will be able to transmit and receive based
on how the button has been configured. The
interaction for all options, with the exceptions of
“Disabled” comes with specific LED indications.
Programmable Top Button Options:
Private Reply – Enters the Private Call mode
with the last user that was transmitting on the
English
28
talkgroup when the Programmable Top Button
is pressed.
Private Direct Call – Enters into Private Direct
Call mode with a pre-programmed radio user
ID
Note:
The radio user ID must be configured via the
CPS
Call All Available – Calls all radio users that
are available in all channels. This feature is
only available when the radio is programmed
using a PIN.
Note:
Only radios that are not currently
transmitting or receiving hears the call.
Radios in private hangtime does not receive
the call.
IMPORTANT: Call All Available feature does NOT
interrupt ongoing conversations.
Disabled – When the Programmable Top
Button is not configured, pressing it returns a
bonk tone. No call is made or initiated.
TRANSMITTING AND RECEIVING
Press the (+) button to increase the volume, or
the (-) button to decrease the volume.
•
To receive, listen through the speaker. To
respond, press the PTT (Push to Talk) and
WAIT to hear the Talk Permit Tone (a quick
double beep) BEFORE you start speaking.
Hold the radio vertically 1 to 2 inches (2.5cm to
5cm) from mouth when talking. Release the
PTT to listen.
•
•
The Tx/Rx Indicator slow blinks RED when on
standby. When the radio is transmitting, the Tx/
Rx Indicator is solid RED.
When the radio is receiving, the Tx/Rx
Indicator LED blinks RED quickly.
Solid Red
Tx/Rx
Indicator
LED when
transmitting
Talking to a Group in a Channel
To transmit, press the PTT (Push to Talk) and
WAIT to hear the Talk Permit Tone (a quick
double beep) BEFORE you start speaking.
GETTING STARTED
•
PRIVATE REPLY
Note:
All the DLR Series radio Programmable Top
Button is defaulted to Private Reply function.
If you need to change this setting, please
use the free online CPS software that is
available in
www.motorolasolutions.com/DLR.
29
English
GETTING STARTED
Private Reply Request
Privately reply to someone talking to a group by
pressing the Programmable Top Button (while
the person is still talking) in order for your
Private Reply request to be queued.
Press button to queue up
for private reply
If your Private Reply request is successfully in
queue, the Programmable Top Button starts
blinking GREEN.
Note:
You will not be able to talk to the person
privately UNTIL the person transmitting
finish the transmission.
While waiting in queue to talk privately, you will
receive a call reminder tone after 1 minute of
being in queue followed by a reminder 4
minutes after that. No other reminder will be
heard afterwards, but you will remain in queue
until the Private Reply mode is exited.
Private Reply Hang Time
The radio allows a window of a few seconds for
anyone to press the Top Programmable and
still be able to queue the Private Reply request
after a user has finished transmitting (or
English
30
Programmable Top Button
LED blinks GREEN when
queued up
GETTING STARTED
talking). This time window is called "Group
Hang Time" (check the CPS settings for more
details). If you private reply within this Group
Hang Time, you can talk privately to the last
user that was transmitting. If the user is busy in
another call you receive a "busy" tone instead.
If you're out of the Hang Time window, you
cannot talk privately but will still be in Group
Talk mode.
Note:
The Programmable Top button LED will
remain OFF and you will hear a tone if:
•
The Private Reply is not successful due to the
request being done outside the Group Hang
Time.
•
Radio ID cannot be stored (outside of hang
time).
•
Programmable Top Button is set to ‘Disabled’.
31
English
GETTING STARTED
Programmable Top Button LED stays
solid GREEN while in private mode
(either by receiving, transmitting or
stand by).
Programmable Top Button
LED stays illuminated in
Private Call
Talking in a Private Mode
Once you have entered the private mode
(either due to Private Reply or Direct Private
Call), the Programmable Top Button LED
illuminates solid GREEN and you will hear a
distinct Private Talk Permit Tone, to indicate
your conversation is private. (The Tx/Rx LED
indications are as described in the
“Transmitting and Receiving” on page 29).
English
To talk, press and hold the PTT button, while in
Private Mode. Begin to talk after you hear the
Private Talk Permit Tone. Release the PTT
button when finished.
32
IMPORTANT: Always make sure the Programmable
Top Button LED is illuminating GREEN
before intending to talk in private
mode. If the button is not illuminated,
your conversations will be heard by all
users in the channel.
Ending a Private Reply Or Direct Call
To end a private or direct call:
•
Long press and hold the Programmable Top
to the current selected channel or talkgroup. An
end tone is heard by both call participants when
the call is ended, or
•
Allow call hang timer to expire, effectively ending
the call and return to the current select channel or
talkgroup.
Note:
Ending a private or direct call by pressing
and holding the Programmable Top Button
is NOT possible if either radio is
transmitting.
When a private or direct call is ended, an
end tone plays for both call participants
when the call is ended.
Only the call initiatior can end a private or
direct call.
PRIVATE DIRECT CALL
Note:
In order to be able to use this feature, the
Programmable Top Button should have
This feature allows you to initiate a private call
to a predetermined user, by pressing the
Programmable Top Button.
Once you press the Top Programmable Button
and if the user on the other end is available, the
Top Programmable Button starts blinking
GREEN. Push and hold the PTT button to talk.
You will hear the distinctive Private Talk Permit
Tone and the Top LED illuminates solid
GREEN to indicate that you are in a private
call. Release the PTT button to hear.
GETTING STARTED
Button to end the private or direct call and return
been previously mapped for the Private
Direct Call function. Refer to the “Setting the
Programmable Top Button Options” on
page 39 and “Customer Programming
Software (CPS)” on page 41 for details.
If you press the Programmable Top Button and
the user that you are trying to reach is busy, the
radio gives you a busy tone. The
Programmable Top Button blinks GREEN
indicating you are in queue waiting to talk.
33
English
There will be tone reminders to alert you that
you're still in queue (similar to Private Reply).
GETTING STARTED
Note:
Programmable Top Button
LED blinks when queued up
You will not be able to talk to the person
privately UNTIL the person on the other end
finish the transmission.
Press button to queue up
for Private Direct Call
Note:
A call reminder tone sounds after 1 minute of
being in queue followed by a reminder 4
minutes after. No other reminder is heard
afterwards, but you remain in queue until the
mode is physically exited.
This assumes that the radio ID to be called
in private is already stored and is always on
Private Direct Call.
While queued for Private Direct Call – press
and hold the PTT button to speak directly to the
stored Radio ID.
•
If successful: During Private Direct Call
Transmitting, Programmable Top button becomes
solid green and the Tx/Rx Indicator LED stays
solid red and you will hear a distinct Private Talk
permit tone. Begin speaking to the private
English
34
TALK RANGE
individual.
Receiving radio’s Programmable Top Button
TALK RANGE
illuminates solid green and the receiver hears a
they are in a private call.
Model
Programmable Top Button LED stays
solid green while receiving in Private
Direct Call
ISM
900 MHz
Industrial
Multi-Level
Inside steel/
concrete Industrial
buildings
Inside multilevel buildings
Up to 300,000 Sq. Ft. Up to 20 Floors
To establish a proper two-way communication,
the channel and PIN (Profile ID Number)
settings must be the same on both radios. This
depends on the stored profile that has been
preprogrammed on the radio:
1.
•
If not successful: A busy unavailable tone
sounds and the Programmable Top Button
continues to blink and queued up for private call.
You can continue trying as long as you are
queued up. A beep sounds every few seconds
while queued.
GETTING STARTED
private tone before voice begins, indicating that
Channel: Current channel that the radio is
using, depending on radio model.
2.
PIN (Profile ID Number): Choose a customized
PIN via CPS or Front Panel Programming.
Refer to “Setting Profile ID Number (PIN)” on
page 38 and “Customer Programming Software
(CPS)” on page 41 for more details.
35
English
RADIO STATUS
GETTING STARTED
RADIO STATUS
English
LED INDICATION
AUDIBLE TONE
Channel Busy
Not Available
Busy Tone
Cloning Mode
Not Available
“Cloning Mode”
Cloning In Progress
Double Blink Orange
Not Available
Fatal Error at Power up
One Green Blink, One Orange Blink,
One Green Blink, then repeat for 4
seconds
TBA
Low Battery
Not Available
TBA
Low Battery Shutdown
Fast Red Heartbeat
TBA
Power-Up
Solid Red for 2 seconds
“Battery Level ,
Channel ”
‘Idle’ Programming Mode /
Channel Mode
Not Available
Chirp Tone followed by
“Programming Mode”
Transmit (Tx)
Solid Red
Not Available
Receive (RX)
Fast Red Heartbeat
Not Available
36
ADVANCED RADIO
CONFIGURATION
The navigation is guided by an audible voice
prompt.
•
Profile ID Number (PIN),
•
Maximum Channels,
•
Programmable Top Button Options, and
•
Microphone Gain.
The Profile ID Number (PIN) feature allows
you set unique 4 digits profile identification
(0000 – 9999) to your radio.
The Maximum Channels feature sets the
number of maximum channels allowed in the
radio.
•
Private Reply,
•
Private Direct Call,
•
Call All Available, and
•
Disabled.
Note:
The default feature for the Programmable
Top Button is Private Reply.
Usage of the Direct Call feature requires a
User ID to be pre-programmed via the CPS.
The Microphone Gain feature allows you to
adjust the sensitivity level of the microphone to
fit different users or operating environment.
The default level of Microphone Gain is
“Normal”.
ADVANCED RADIO
CONFIGURATION
Advanced Radio Configuration provides you
with the ability to check and configure the
following settings from a pre-programmed list
without the need to use a computer.
The Programmable Top Button Options
allows you to assign one of the following four
features to the Programmable Top Button:
Entering Advanced Radio Configuration
To enter the Advanced Radio Configuration:
1.
Turn OFF the radio.
2.
Press the PTT, (+) and Power buttons
simultaneously and hold for 3~5 seconds. A
37
English
“programming tone” sounds and you hear the
1.
voice announcement “Programming Mode,
announcement “Current Profile ID <####>, to
ADVANCED RADIO
CONFIGURATION
press Menu to continue”.
Note:
3.
Short press the Menu button to navigate along
change press (+) or (-)”.
Note:
2.
Radio PIN. The voice announces “First digit
<#>, to change press (+) or (-)”. Short press the
•
Profile ID Number,
(+) or (-) button until you reach the desired
•
Maximum Channels,
•
Programmable Top Button Options, and
number. Numbers loop from 0 – 9.
3.
To exit the Advanced Radio Configuration
Mode:
change press (+) or (-)”.
4.
Setting Profile ID Number (PIN)
While in Programming Mode:
38
Repeat Step 2 and 3 until all 4 digits are set and
you hear the voice announcement “Profile ID
saved as <####>, press Menu to continue”.
5.
Press the Menu button to continue to the next
programmable feature available.
Press and hold the PTT button until a “beep”
sound is heard.
To move to the next digit, short press the Menu
button. The voice announces “2nd digit <#>, to
Microphone Gain.
The voice announcements indicate the menu
the settings, press the (+) or (-) buttons.
English
Press the (+) or (-) button to start setting the
features available:
features and their current settings. To modify
1.
User must advance through all 4 digits
before new Radio PIN will be saved.
and loop through the different programmable
•
4.
The Tx/Rx Indicator LED blinks a steady red
heartbeat during the Programming Mode.
Press the Menu button to hear the voice
Note:
If you are done programming, press and
hold the PTT button until a "beep" sound is
heard, to exit the programming mode.
Setting the Maximum Channels
While in Programming Mode:
1.
Press the Menu button until the voice
While in Programming Mode:
1.
2.
setting>, to change press (+) or (-)” is heard.
Press the (+) or (-) button to cycle through the
number of maximum channels allowed. The
Note:
voice announces the maximum channels set
2.
3.
Numbers loop based on the number of
channels allowed by your radio model.
announces the options available “

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Motorola Solutions, Inc.
Create Date                     : 2015:03:09 18:42:56Z
Modify Date                     : 2015:03:12 13:02:32-04:00
Subject                         : Draft 3.1
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : FrameMaker 8.0
Metadata Date                   : 2015:03:12 13:02:32-04:00
Format                          : application/pdf
Description                     : Draft 3.1
Title                           : DLR Series Two Way Radios User Guide [P/N# MN001132A01 Rev. AA]
Creator                         : Motorola Solutions, Inc.
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:afcd4253-5dc4-4028-a9a0-43f7947a7ffa
Instance ID                     : uuid:b26be1b3-a974-4c99-ba70-c1a5dda3e785
Page Mode                       : UseOutlines
Page Count                      : 62
EXIF Metadata provided by EXIF.tools
FCC ID Filing: AZ489FT5870

Navigation menu