Multi Tech Systems 92U09G17825 SocketModem CDMA User Manual MTSMC C1 DRAFT S000342L
Multi Tech Systems Inc SocketModem CDMA MTSMC C1 DRAFT S000342L
Contents
- 1. Setup Note_CDMA-82003640
- 2. SocketModem CDMA_Darasheet
- 3. User Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1204041 |
| Application ID | 8WFv9YrJLtmsd0I6J4MSCA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 308.1kB (3851291 bits) |
| Date Submitted | 2009-11-24 00:00:00 |
| Date Available | 2009-12-09 00:00:00 |
| Creation Date | 2009-11-20 08:44:33 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2009-11-20 08:44:33 |
| Document Title | Microsoft Word - MTSMC-C1 DRAFT S000342L.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Johee_Chang |
Universal Socket Connectivity Embedded Device Networking Solutions Comment [DAR1]: Resaved as cover page graphic.jpg 65KB 09/17/09 – filed under graphics new in K (poreviously COVER_UniversalSockettechclouds.jpg 9/02/09 555KB in Universal_SocketModem/Graphics_R ev_F) Hardware Guide for Developers Copyright and Technical Support Universal Socket Connectivity Hardware Guide for Developers, PN S000342K, Version K For the following products (The list indicates base models for each product. See each product chapter product build options): Embedded Wireless Modems SocketModem® Cell – MTSMC-G2 SocketModem® Cell – MTSMC-G2-GP (Global Positioning) SocketModem® iCell – MTSMC-G2-IP SocketModem® CDMA – MTSMC-C1 SocketModem® EDGE – MTSMC-E1 Socket Modem® HSDPA – MTSMC-H Embedded Analog Modems SocketModem® – MT9234SMI SocketModem® – MT5692SMI SocketModem® – MT2492SMI SocketModem® – MT2456SMI-22 Embedded Device Servers SocketModem IP® – MT100SEM-IP SocketWireless® Wi-Fi® – MT810SWM-IP SocketWireless® Bluetooth® – MTS2BTSMI Copyright This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2004-9 by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes. See the Multi-Tech Web site for current revisions of documentation. Trademarks Trademarks and Registered Trademarks of Multi-Tech Systems, Inc. are SocketModem, SocketWireless, SocketEthernet IP, and the Multi-Tech logo. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. Bluetooth is a registered trademark of the Bluetooth SIG, Inc. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Warranty and Repairs Statement Please see the Multi-Tech Systems, Inc. Web site for the current Warranty and Repairs Statement. http://www.multitech.com/COMPANY/Policies/warranty/ World Headquarters Multi-Tech Systems, Inc. 2205 Woodale Drive Mounds View, Minnesota 55112 Phone: 763-785-3500 or 800-328-9717 Fax: 763-785-9874 Internet Address: http://www.multitech.com Technical Support Country Europe, Middle East, Africa: U.S., Canada, all others: By Email support@multitech.co.uk support@multitech.com By Phone +(44) 118 959 7774 800-972-2439 or 763-717-5863 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Revision Notes Revision Notes Rev. Date J.1 07/01/09 Description • Reorganized the manual so that wireless products are grouped in Part 2, Analog SocketModems are grouped in Part 3, and Device Servers are grouped in Part 4 • Added new products: MTSMC-G2 and MT100SEM-IP • Removed MT2456SMI-22 and MTSMC-G-F4 chapters • Removed the text for the Warranty and Repairs Statement and linked to the Multi-Tech Web site for the policy • Updated the Universal Developer Kit Contents • To Pin 24 Description: added Reset stats for MTSMC-G2, MTSMC-C, and MTSMC-E • Updated Mechanical Drawings for Analog Modems in Chapter 1 • Added MTSMC-G2 to the Maximum Component Height • Fixed the 5V/3.3V Jumper on the Developer Board • Added the UFL-to-SMA Coax Cable information to Chapter 1 • Added a new RF Safety section in Chapter 1 • Added the MTSMC-G2 to the Upgrading Firmware Table • Changed/updated label example for CDMA and Analog SocketModems • Updated the EMC, Safety, and R&TTE Directive Compliance Statement • Updated the EMC Requirements for the United States regulatory section • Added Thailand Approval Statement for the MT9234SMI • Added the Brazil Approval section • Added the English version of Chinese Standards section • For each listing of power consumption, added the following statement (required by QA): Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. • Changed the HSDPA max operating temperature to +60°C • Added sleep mode power stats for MT9234SIM • Updated the Ethernet Interface drawings (Non-Isolated & Isolated Designs) for the MT100SEM-IP • Added an Auto Discovery Manager section to the MT100SEM-IP chapter • Updated/corrected the Tip and Ring drawings. J.2 07/30/09 • Updated Mechanical Drawings for SocketModem Cell (MTSMC-G2) and SocketModem iCell (MTSMC-G2-IP). • Changed the title of two Mechanical Drawings in Chapter 1. J.3 08/28/09 • Updated Mechanical Drawings for SocketModem GPRS (MTSMC-G2). • Added new Mechanical Drawings for SocketModem CDMA( MTSMC-C). • Added new Mechanical Drawings for SocketModem HSDPA MTSMC-H J.4 10/15/09 • Added GPS section to G2 chapter (added the power draw table for G2 for GPS). • Brought back the chapter covering the SocketModem MT2456SMI-22. 11/18/09 • New chapters for new products: SocketModem MT5692SMI, Device Server MT810SWM-IP, and SocketModem EDGE (MTSMC-E1). • Deleted chapters SocketModem MT5656SMI and MT5656SMI-IP. • Added Sleep Mode Power Draw statistics for the SocketModem MT9234SMI. • Added new Mechanical Drawings for SocketModem HSDPA (MTSMC-H) and SocketModem CDMA (MTSMC-C). • Updated the Power Requirements for the MT2492SMI and MT5692SMI (10/16/09). • Added Global Positioning section for the SocketModem Cell / SocketModem iCell (MTSMC-G2) and GPS power draw. • Reorganized Chapter 1 – general information, wireless information, and analog information. • Added Japan's Standards statement. • Updated Mechanical Drawings in Chapter 1. • New Developer Board Block Diagram with antenna system added. 11/18/09 • Add new product CDMA (MTSMC-C1). Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Table of Contents Table of Contents PART 1 – UNIVERSAL SOCKET CONNECTIVITY ........................................................ 9 Chapter 1 – Universal Socket Connectivity......................................................................................10 Multi-Tech Embedded Solutions ................................................................................................................10 Universal Socket Connectivity Features .................................................................................................10 The Universal Socket Design..................................................................................................................10 Universal Developer Kit Contents ...........................................................................................................11 AT Commands for All Embedded Products Are Included on the Developer Kit CD................................11 Universal Socket Pin Out ............................................................................................................................12 Universal Pin Descriptions ......................................................................................................................12 Design Considerations ................................................................................................................................16 Noise Suppression Design Considerations.............................................................................................16 PC Board Layout Guidelines...................................................................................................................16 Electromagnetic Interference (EMI) Considerations ...............................................................................17 Electrostatic Discharge Control...............................................................................................................17 Phone Line Warning Statement for the Developer Board .......................................................................17 Mechanical Drawing in Inches for the Listed Products ............................................................................18 Mechanical Drawing in Millimeters for Listed Products ...........................................................................19 Maximum Component Height / PCB Length and Width............................................................................20 SocketModem Developer Board .................................................................................................................21 Board Components .................................................................................................................................22 Jumpers and Corresponding Signals ......................................................................................................22 SocketModem Developer Board Block Diagram.....................................................................................23 Developer Board Schematics .................................................................................................................24 Developer Board Schematics .................................................................................................................25 Developer Board Schematics .................................................................................................................26 Developer Board Schematics .................................................................................................................27 Developer Board Schematics .................................................................................................................28 Upgrading Firmware ....................................................................................................................................29 XMODEM Serial Port Upgrade ...............................................................................................................30 Multi-Tech Systems, Inc. Flash Programming Protocol ..........................................................................31 Wireless Information ...................................................................................................................................34 Antenna System for Wireless Devices ....................................................................................................34 Account Activation for Wireless Devices.................................................................................................37 Wireless Approvals and Labeling Requirements ....................................................................................37 Analog Information ......................................................................................................................................39 Recommended Parts for Analog SocketModems ...................................................................................39 Analog Labeling Requirements...............................................................................................................40 Safety Notices and Warnings......................................................................................................................43 Wireless Safety.......................................................................................................................................43 Analog Telecom Safety Warnings...........................................................................................................44 Telecom Approvals for Analog Modems .................................................................................................45 Regulatory Compliance Statements...........................................................................................................46 Country/Region-Specific Statements ......................................................................................................46 Waste Electrical and Electronic Equipment Statement ...........................................................................51 Restriction of the Use of Hazardous Substances (RoHS).......................................................................52 Information on HS/TS Substances according to Chinese Standards in English .....................................53 Information on HS/TS Substances According to Chinese Standards in Chinese....................................54 PART 2 – WIRELESS SOCKETMODEMS.................................................................... 55 Chapter 2 – SocketModem® Cell (MTSMC-G2) & SocketModem® iCell (MTSMC-G2-IP) ..............56 Introduction ..................................................................................................................................................56 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Table of Contents Product Build Options and Ordering Information .....................................................................................56 AT Commands Reference Guides ..............................................................................................................56 Technical Specifications .............................................................................................................................57 DC Electrical Characteristics ......................................................................................................................58 Power Measurements ..................................................................................................................................58 Mechanical Drawings – Basic Build ...........................................................................................................60 Application Notes ........................................................................................................................................64 Flashing LED Interface ...........................................................................................................................64 RF Performances....................................................................................................................................64 RF Connection and Antenna...................................................................................................................64 Microphone Inputs ..................................................................................................................................64 Changing the Quad Band .......................................................................................................................65 Global Positioning System (GPS)...............................................................................................................66 Technical Specifications .........................................................................................................................66 Features..................................................................................................................................................66 Underwriters Laboratories Required Global Positioning System (GPS) Statement ................................66 Chapter 3 – SocketModem® CDMA (MTSMC-C1).............................................................................67 Introduction ..................................................................................................................................................67 Product Build Options and Ordering Information .....................................................................................67 AT Commands Reference Guides ..............................................................................................................67 Technical Specifications .............................................................................................................................68 Mechanical Drawings – Basic Build ...........................................................................................................70 DC Electrical Characteristics ......................................................................................................................71 Power Measurements*.................................................................................................................................71 Application Notes ........................................................................................................................................72 Flashing LED Interface ...........................................................................................................................72 RF Interface ............................................................................................................................................72 RF Connection and Antenna...................................................................................................................72 Provisioning a Generic SocketModem CDMA ........................................................................................73 CDMA Terminology and Acronyms.........................................................................................................74 Chapter 4 – SocketModem® EDGE (MTSMC-E1)..............................................................................76 Introduction ..................................................................................................................................................76 Product Build Options and Ordering Information .....................................................................................76 AT Commands Reference Guide ................................................................................................................76 Technical Specifications .............................................................................................................................77 Mechanical Drawings – Basic Build ...........................................................................................................78 Mechanical Drawings – Voice Build ...........................................................................................................80 DC Electrical Characteristics ......................................................................................................................82 Power Measurements ..................................................................................................................................82 Application Notes ........................................................................................................................................83 RF Performances....................................................................................................................................83 RF Connection and Antenna...................................................................................................................83 Audio Interface – Electrical Characteristics.............................................................................................83 Microphone Inputs ..................................................................................................................................83 Chapter 5 – SocketModem® HSDPA (MTSMC-H) .............................................................................84 Introduction ..................................................................................................................................................84 Product Build Options and Ordering Information .....................................................................................84 AT Commands Reference Guide ................................................................................................................84 Technical Specifications .............................................................................................................................85 Mechanical Drawings – Basic Build ...........................................................................................................87 Mechanical Drawings – USB Build .............................................................................................................89 DC Electrical Characteristics ......................................................................................................................90 Power Measurements*.................................................................................................................................90 Application Notes ........................................................................................................................................91 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Table of Contents RF Performances....................................................................................................................................91 RF Connection and Antenna...................................................................................................................91 Air Interface ............................................................................................................................................91 Configuring the HSDPA Modem on Linux SLAX 6..................................................................................93 Baud Rate Switches on the HSDPA SocketModem ...............................................................................94 Operating Modes ....................................................................................................................................95 Turn off the SocketModem Using AT Command ....................................................................................96 Automatic Shutdown ...............................................................................................................................96 Temperature Control during an Emergency Call.....................................................................................96 Power Saving..........................................................................................................................................96 Interface Signal Descriptions ..................................................................................................................98 PART 3 – ANALOG SOCKETMODEMS ...................................................................... 99 Chapter 6 – SocketModem® (MT9234SMI) ......................................................................................100 Introduction ................................................................................................................................................100 Product Build Options and Ordering Information ...................................................................................100 AT Commands Reference Guide ..............................................................................................................100 Technical Specifications ...........................................................................................................................101 SocketModem Pin Out...............................................................................................................................103 Serial Pin Out........................................................................................................................................103 Parallel Pin Out.....................................................................................................................................104 DC Electrical Characteristics ....................................................................................................................105 Parallel Timing Requirements...................................................................................................................106 SocketModem Parallel Interface Internal Registers................................................................................107 Application Notes ......................................................................................................................................114 Tip and Ring Interface...........................................................................................................................114 Chapter 7 – SocketModem® (MT5692SMI) ......................................................................................115 Introduction ................................................................................................................................................115 Product Build Options and Ordering Information ...................................................................................115 AT Commands Reference Guide ..............................................................................................................116 Technical Specifications ...........................................................................................................................117 Pin Outs ......................................................................................................................................................119 Operating Conditions ................................................................................................................................121 Absolute Maximum Rating ........................................................................................................................121 DC Electrical Characteristics ....................................................................................................................121 Power* Measurements...............................................................................................................................122 Parallel Host Bus Timing Table ................................................................................................................123 SocketModem Parallel Interface ...............................................................................................................124 Register Functional Definitions ................................................................................................................125 Application Notes ......................................................................................................................................134 Tip and Ring Interface...........................................................................................................................134 Microphone and Speaker......................................................................................................................135 Chapter 8 – SocketModem® (MT2492SMI) ......................................................................................137 Introduction ................................................................................................................................................137 Product Build Options and Ordering Information ...................................................................................137 AT Commands Reference Guide ..............................................................................................................137 Technical Specifications ...........................................................................................................................138 SocketModem Pin Out...............................................................................................................................139 DC Electrical Characteristics ....................................................................................................................139 Application Notes ......................................................................................................................................140 Tip and Ring Interface...........................................................................................................................140 Chapter 9 – SocketModem (MT2456SMI-22)..................................................................................141 Introduction ................................................................................................................................................141 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Table of Contents Product Ordering Information...................................................................................................................141 AT Commands Reference Guide ..............................................................................................................141 Technical Specifications ...........................................................................................................................142 SocketModem Configuration ....................................................................................................................143 Serial Configuration ..............................................................................................................................143 Electrical Characteristics ..........................................................................................................................144 3.3V Serial SocketModem ....................................................................................................................144 5V Serial SocketModem .......................................................................................................................144 Applications Notes ....................................................................................................................................145 Tip and Ring Interface...........................................................................................................................145 PART 4 – EMBEDDED DEVICE SERVERS ............................................................... 146 Chapter 10 – SocketEthernet IP® (MT100SEM-IP)..........................................................................147 Introduction ................................................................................................................................................147 Product Build Options and Ordering Information ...................................................................................147 AT Commands Reference Guide ..............................................................................................................147 Technical Specifications ...........................................................................................................................148 SocketEthernet IP Pin Out.........................................................................................................................149 DC Electrical Characteristics ....................................................................................................................150 Power* Measurements...............................................................................................................................150 Application Notes ......................................................................................................................................151 Ethernet Interface – Non-Isolated Design .............................................................................................151 Ethernet Interface – Isolated Design.....................................................................................................151 Recommended Parts ............................................................................................................................151 The Windows-Based Auto-Discovery Manager ....................................................................................153 Chapter 11 – SocketWireless® Wi-Fi® (MT810SWM-IP) .................................................................155 Introduction ................................................................................................................................................155 Product Build Options and Ordering Information ...................................................................................155 AT Commands Reference Guide ..............................................................................................................155 Technical Specifications ...........................................................................................................................156 Mechanical Drawings ................................................................................................................................158 Mechanical Drawings ................................................................................................................................159 Operating Conditions ................................................................................................................................161 Absolute Maximum Rating ........................................................................................................................161 DC Electrical Characteristics ....................................................................................................................161 Power Measurements*...............................................................................................................................161 Application Notes ......................................................................................................................................162 RF Interface ..........................................................................................................................................162 Default Power Up Settings....................................................................................................................162 Antenna Requirements and Sources ....................................................................................................162 Regulatory Requirements for the Wi-Fi Antenna ..................................................................................163 Chapter 12 – SocketWireless® Bluetooth® (MTS2BTSMI) .............................................................164 Introduction ................................................................................................................................................164 Notes about Byte Gaps and Data Latency ...............................................................................................164 Product Build Options and Ordering Information ...................................................................................164 AT Commands Reference Guide ..............................................................................................................164 Technical Specifications ...........................................................................................................................165 SocketWireless Bluetooth Pin Out ...........................................................................................................166 DC Electrical Characteristics ....................................................................................................................166 Application Notes ......................................................................................................................................167 RF Interface ..........................................................................................................................................167 Sources for Peripheral Devices ............................................................................................................167 Default Power Up Settings....................................................................................................................168 Example of a Master Discovery/Connection Sequence ........................................................................169 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Table of Contents Example of a Slave Command Sequence ............................................................................................169 Disabling Flow Control Using AT Commands .......................................................................................170 Other Examples ....................................................................................................................................170 Changing Configuration ........................................................................................................................170 Index ...................................................................................................................................................172 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Part 1 − Universal Socket Connectivity Part 1 Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Multi-Tech Embedded Solutions Multi-Tech’s embedded device networking solutions instantly add communication ability to your existing or new product with minimal engineering effort giving you an edge on your competition while accelerating your time-to-market. Our universal socket family of embedded solutions is designed around a flexible comm-port architecture to provide analog dial-up, cellular, Wi-Fi or Bluetooth® wireless, or Ethernet socket connectivity with interchangeable socket devices. This means you can utilize one system design and populate it with your preferred connectivity option giving you flexibility and a seamless migration path to future technologies. Universal Socket Connectivity Features • • • • • Flexible comm-port architecture Interchangeable socket devices Cost-effective system design Easy migration to future technologies Complete global compliance The Universal Socket Design Each pin on a SocketModem corresponds to a particular function. The universal socket design provides a universal location for each function pin. This allows each SocketModem to be used in a common board. Comment [DAR2]: Saved as Universal SocketModem with pins.png 81KB saved in New graphics for K Comment [DAR3]: Pin Out_assignment_overview_fromDean _p5.png Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 10 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Universal Developer Kit Contents Products described in this guide can be used to develop and evaluate your products and applications using the MTSMI-UDK (Universal Developer Kit). • Developer Board: One MTSMI-UDK Developer Board • Power Supply: One 100-240V 9V-1A power supply with removable blades: ♦ One US blade/plug ♦ One EURO blade/plug ♦ One UK blade/plug • Cables ♦ One RJ-45 Ethernet cable ♦ One RJ-11 phone cable ♦ One DB9F-DB25M serial cable ♦ One 1.5 meter USB cable • Antenna Cables ♦ One SMA-to-MMCX antenna cable (for cellular antennas) ♦ Two SMA-to-UFL antenna cables (one for select cellular antennas and one for the GPS antenna) ♦ One RSMA-to-UFL antenna cable (for Bluetooth and Wi-Fi antennas) • Antennas ♦ One quad band antenna 850/1900/900/1800 (for cellular modems) ♦ One 2.4GHz, ½ WAVE antenna with reverse polarity (for Bluetooth and Wi-Fi devices) ♦ One GPS antenna (for the SocketModem iCell) • Modem Activation Customer Notices (included on the Universal Socket Connectivity Developer CD) ♦ Aeris ♦ CDMA ♦ Cellcom ♦ GSM ♦ IVC ♦ Sprint ♦ Verizon • One Universal Socket Connectivity Developer CD • One Promotional Screwdriver AT Commands for All Embedded Products Are Included on the Developer Kit CD AT Commands Multi-Tech provides Reference Guides for each SocketModem's AT commands. These reference guides are available on the CD included in the Developer Kit. They are also available by email at mailto:oemsales@multitech.com or by using the Developer Guide Request Form on Multi-Tech's Web site. Fax Commands for Analog Modems Fax Commands are included in the AT Command Reference Guide when applicable to the product. They are available on the CD included in the Developer Kit. Note: Fax Commands supported by product: • SocketModem MT9234SMI supports all Class 1 and Class 2 commands (Class 1, 1.0, 2, 2.0/2.1) • SocketModem MT5692SMI supports Class 1 & 1.0 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 11 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Universal Socket Pin Out Comment [DAR4]: Pin Out_Universal_July_2008_p14..png & FH9 7/14/08 Comment [DAR5]: SocketModem Uiversal Pinout flat view. png -- saved in Graphics new in Rev K -- 50 KB Top View – Universal SocketModem Pin Out Universal Pin Descriptions Pin Signal Name Tip In/Out Description I/O Ring I/O NA Safety Void TX+ TXRX- RX+ 11 12 22 Safety Void Dummy TCLK RCLK MIC+ 23 MIC- NA Tip Signal from Telco. Tip connection to the phone line (RJ-11 Pin 4). The SocketModem is Tip/Ring polarity insensitive. Ring Signal from Telco. Ring connection to the phone line (RJ-11 Pin 3). The SocketModem is Tip/Ring polarity insensitive. Safety Clearance. 2.5 mm is required between TNV circuits and SELV circuits. Transmit Outputs (TX+ and TX-). Differential transmit outputs for Ethernet and ISDN. Transmit Outputs (TX+ and TX-). Differential transmit outputs for Ethernet and ISDN. Receive Inputs. Differential receive input pins for Ethernet. Dummy pin for MT810SWM-IP. Receive Inputs. Differential receive input pins for Ethernet. Safety Clearance. 2.5 mm is required between TNV circuits and SELV circuits. Dummy pin for EDGE. Transmit Data Sync Clock. TX synchronous data clock for ISDN sync data mode. Receive Data Sync Clock. RX synchronous data clock for ISDN sync data mode. Microphone positive input. See microphone sections in GPRS, CDMA, EDGE chapters. Microphone negative input. See microphone sections in GPRS, CDMA, EDGE chapters. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 12 Part 1 − Universal Socket Connectivity Pin 24 Signal Name –RESET* 25 USB_VBUS 26 27 28 29 GND USB_DP USB_DN LED DCD In/Out GND I/O I/O 30 LED RX 31 LED DTR 32 LED TX 33 –RTS Chapter 1 – Universal Socket Connectivity Description Device Reset (with pull-up). The active low –RESET input resets the device logic and returns the configuration of the device to the original factory default values or "stored values" in the NVRAM. –RESET is tied to VCC through a time-constant circuit for “Power-on-Reset” functionality. The SocketModem is ready to accept commands after a fixed amount of time (“X” Time) after power-on or reset. Model Time Constant "X" Time Minimum Reset Pulse* MTSMC-G2 250 ms 6 seconds 100us MTSMC-C1 250 ms 3-15 seconds 500us MTSMC-E1 250 ms 3-15 seconds 500us MTSMC-H 250 ms 10 seconds 100us MT9234SMI 400 ms 6 seconds 100us MT5692SMI 250 ms 6 seconds 100us MT2492SMI 250 ms 6 seconds 100us MT100SEM-IP 250 ms 6 seconds 100us MT810SWM-IP 250 ms 6 seconds 100us MTS2BTSMI 250 ms 6 seconds 100us *The SocketModem device may respond to a shorter reset pulse. Reset Line Interface for the MT5692SMI. The modem’s reset line employs a 10K pull up resistor. If an open collector driver is to be used, run that output to the modem only and use a separate driver for other embedded components. The modem’s reset signal may also be driven by a circuit that both sinks and sources current if desired. It is also important to note that these modems do not require an external reset. They have their own internal reset circuitry and voltage monitor and will function correctly even if the reset input is open. Reset GPRS and CDMA (MTSMC-G2 and MTSMC-C1). This signal is used to force a reset procedure by providing low level during reset of at least 500us. The signal is considered an emergency reset only. A reset procedure is already driven by internal hardware during the power-up sequence. If no external reset is necessary, this input can be left open. If used (emergency reset), it has to be driven by an open collector or an open drain. Reset EDGE with pull-up (MTSMC-E1). The active low –RESET input resets the device logic and returns the configuration of the device to the original factory default values of "stored values" in the NVRAM. The SocketModem is ready to accept commands after a fixed amount of time after power-on or reset. USB Voltage Sense. Senses the voltage level of the USB to determine if the bus is available. Logic Ground. USB Data Positive. Positive pin of the USB data pair. USB Data Negative. Negative pin of the USB data pair. DCD (Active High). Output from 74LCX14 with a 1000 Ohms resistor in series. SocketWireless Bluetooth (MTS2BTSMI): When lit, indicates a connection. No series resistor. RX (Active High). Output from 74LCX14 with a 1000 Ohms resistor in series. SocketWireless Bluetooth (MTS2BTSMI): No series resistor. DTR (Active High). Output from 74LCX14 with a 1000 Ohms resistor in series. SocketWireless Bluetooth (MTS2BTSMI): No series resistor. TX (Active High). Output from 74LCX14 with a 1000 Ohms resistor in series. SocketWireless Bluetooth (MTS2BTSMI): No series resistor. Request to Send (Active Low). –RTS is controlled by the DTE to indicated whether or not the DTE is ready to receive data. –RTS ON (low) indicates that the DTE is ready to receive data from the modem on RXD. –RTS OFF indicates to the SocketModem that it should not transfer data on the RXD. In the command state, the modem ignores –RTS. Note: When the –RTS pin is not in use, it should be tied low. Comment [DAR6]: For all builds -Dustin 8/24/09 Comment [DAR7]: New from Tim Gunn 07/14/09 Comment [DAR8]: Bud wondered if this text is for E1 too (it was used with initial EDGE). It’s in the section that describes the pin functionality. 9/8/09 review: Reset EDGE with pull-up (MTSMCE1). Dustin's answer Original edge documentation is incorrect. You could probably remove: –RESET is tied to VCC through a time-constant circuit for “Power-onReset” functionality. * RESET – A Design Consideration: Allowing the host processor to control the RESET line of the SocketModem provides the benefit of allowing the host to reset the device in the event of a failure to respond normally. Resetting the SocketModem will return it to a known functional state. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 13 Part 1 − Universal Socket Connectivity Pin In/Out 34 Signal Name –RXD 35 –TXD 36 –RI 37 –DSR 38 –CTS 39 –DCD 40 –DTR 41 42 43 48 49 50 51 56 GND SPKSPK+ GPIO GPIO GPIO GPIO –LED FDX –LED ACT GND I/O I/O I/O I/O 57 58 – LEDLINK Chapter 1 – Universal Socket Connectivity Description Received Data. The SocketModem uses the RXD line to send data to the DTE and to send SocketModem responses to the DTE. In command mode, –RXD data presents the SocketModem responses to the DTE. SocketModem responses take priority over incoming data when the two signals are in competition for –RXD. When no data is transmitted, the signal is held in mark condition. Transmitted Data. The DTE uses the –TXD line to send data to the SocketModem for transmission or to transmit commands to the SocketModem. The DTE holds this circuit in mark state when no data is being transmitted or during intervals between characters. RING (Active Low). Incoming ring signal from phone. Ring Indicate. –RI output ON (low) indicates the presence of an ON segment of a ring signal on the telephone line. The modem will not go off-hook when –RI is active; the modem waits for –RI to go inactive before going off-hook. SocketWireless Bluetooth (MTS2BTSMI). Strobes 1/sec for slave indication. Data Set Ready (Active Low). –DSR indicates SocketModem status to the DTE. – DSR OFF (high) indicates that the DTE is to disregard all signals appearing on the interchange circuits except Ring Indicator (–RI). It reflects the status of the local data set and does not indicate an actual link with any remote data equipment. Clear to Send (Active Low). –CTS is controlled by the SocketModem to indicate whether or not the SocketModem is ready to transmit data. –CTS ON indicates to the DTE that signals on TXD will be transmitted. –CTS OFF indicates to the DTE that it should not transfer data on TXD. Data Carrier Detect (Active Low). –DCD output is ON (low) when a data connection is established and the SocketModem is ready to send/receive data. Data Terminal Ready (Active Low). The –DTR input is turned ON (low) when the DTE is ready to communicate. –DTR ON prepares the modem to be connected, and, once connected, maintains the connection. –DTR OFF places the modem in the disconnect state under control of the &Dn and &Qn commands. Note: When the –DTR pin is not in use, it should be tied low. Logic Ground. Wireless GPRS, CDMA, and EDGE. Negative analog speaker output. Wireless GPRS, CDMA, and EDGE. Positive analog speaker output. General Purpose Input/Output. User-configurable input or output pin. General Purpose Input/Output. User-configurable input or output pin. General Purpose Input/Output. User-configurable input or output pin. General Purpose Input/Output. User-configurable input or output pin. LED Full Duplex (Active Low). LED Output. During normal operation, this pin lights the FDX LED to indicate a full duplex mode. LED Active (Active Low). LED Output. During normal operation, this pin lights the Activity LED when transmitting or receiving. It flashes at a rate of 50ms high and 50ms low when active. LED LINK (Active Low). LED Output. During normal operation, this pin lights the LINK LED to indicate a good link is detected. Pin 58 LED Mode Operating Status Note: Pin 58 may or may not be available on some EDGE/GPRS/CDMA SocketModems currently shipping. Off Subscriber Carrier Mode is OFF or running in SLEEP mode or Alarm mode. 600 ms ON / 600ms OFF No SIM card inserted or no PIN entered, or network search in progress, or ongoing user authentication, or network login in progress. 75 ms ON / 75 ms OFF / 75 ms ON One or more EDGE/GPRS/CDMA contexts activated. 3 s OFF Indicates EDGE/GPRS/CDMA data transfer: When a transfer is Flashing in progress, the LED goes on within 1 second after data packets were exchanged. Flash duration is approximately 0.5 s. ON Depending on type of call: Voice Call: Connected to remote party. Data Call: Connected to remote party or exchange of parameters while setting up or disconnecting a call. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 14 Part 1 − Universal Socket Connectivity Pin Signal Name – LEDCOL In/Out 61 62 – LEDSPD VCC MICV PWR 63 AGND GND 64 SPKR 59 60 Chapter 1 – Universal Socket Connectivity Description LED Collision (Active Low). LED Output. During normal operation, this pin lights the COL LED to indicate a collision. It flashes at 50ms high and 50ms low when active. LED Speed (Active Low). LED Output. During normal operation, this pin lights the SPEED LED to indicate 100Mbps is selected. DC Input Power. 3.3V or 5VDC power, depending upon the build. Single-Ended Microphone. Single-ended microphone input for dial-up SocketModem speakerphone and TAM functions. Analog Ground. Analog ground is tied common with DGND on the SocketModem. To minimize potential ground noise issues, connect audio circuit return to AGND. Speaker. Dual purpose output for call progress signals or speakerphone functions. Call Progress signaling on MT5692SMI and MT2492SMI is a square wave output that can be optionally connected to a low-cost single-ended speaker; e.g., a sounducer or an analog speaker circuit. Call progress on the MT9234SMI is an analog output. Speakerphone Output on the MT5692SMI is under the control of +FCLASS. This is a single-ended analog output. SPKR is tied directly to the CODEC. One side of a differential AC output coupled through a 6.8K ohm resistor and capacitor. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 15 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Design Considerations Noise Suppression Design Considerations Engineering noise-suppression practices must be adhered to when designing a printed circuit board (PCB) containing the SocketModem. Suppression of noise is essential to the proper operation and performance of the modem itself and for surrounding equipment. Two aspects of noise in an OEM board design containing the SocketModem must be considered: on-board/offboard generated noise that can affect digital signal processing. Both on-board and off-board generated noise that is coupled on-board can affect interface signal levels and quality. Of particular concern is noise in frequency ranges affecting modem performance. On-board generated electromagnetic interference (EMI) noise that can be radiated or conducted off-board is a separate, but equally important, concern. This type of noise can affect the operation of surrounding equipment. Most local government agencies have stringent certification requirements that must be met for use in specific environments. Proper PC board layout (component placement, signal routing, trace thickness and geometry, etc.) component selection (composition, value, and tolerance), interface connections, and shielding are required for the board design to achieve desired modem performance and to attain EMI certification. Other aspects of proper noise-suppression engineering practices are beyond the scope of this designer guide. The designer should consult noise suppression techniques described in technical publications and journals, electronics and electrical engineering text books, and component supplier application notes. PC Board Layout Guidelines In a 4-layer design, provide adequate ground plane covering the entire board. In 4-layer designs, power and ground are typically on the inner layers. All power and ground traces should be 0.05 inches wide. The recommended hole size for the SocketModem pins is 0.036 in. +/-0.003 in. in diameter. Spacers can be used to hold the SocketModem vertically in place during the wave solder process. All creepages and clearances for the SocketModem have been designed to meet requirements of safety standards EN60950 or EN60601. The requirements are based on a working voltage of 125V or 250V. When the recommended DAA* circuit interface is implemented in a third party design, all creepage and clearance requirements must be strictly followed in order to meet safety standards. The third party safety design must be evaluated by the appropriate national agency per the required specification. User accessible areas: Based on where the third party design is to be marketed, sold, or used, it may be necessary to provide an insulating cover over all TNV exposed areas. Consult with the recognized safety agency to determine the requirements. Note: Even if the recommended design considerations are followed, there are no guarantees that a particular system will comply with all the necessary regulatory requirements. It is imperative that specific designs be completely evaluated by a qualified/recognized agency. *DAA stands for Data Access Arrangement. DAA is the telephone line interface of the SocketModem. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 16 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Electromagnetic Interference (EMI) Considerations The following guidelines are offered specifically to help minimize EMI generation. Some of these guidelines are the same as, or similar to, the general guidelines but are mentioned again to reinforce their importance. In order to minimize the contribution of the SocketModem-based design to EMI, the designer must understand the major sources of EMI and how to reduce them to acceptable levels. 1. Keep traces carrying high frequency signals as short as possible. 2. Provide a good ground plane or grid. In some cases, a multilayer board may be required with full layers for ground and power distribution. 3. Decouple power from ground with decoupling capacitors as close to the SocketModem power pins as possible. 4. Eliminate ground loops, which are unexpected current return paths to the power source and ground. 5. Decouple the telephone line cables at the telephone line jacks. Typically, use a combination of series inductors, common mode chokes, and shunt capacitors. Methods to decouple telephone lines are similar to decoupling power lines; however, telephone line decoupling may be more difficult and deserves additional attention. A commonly used design aid is to place footprints for these components and populate as necessary during performance/EMI testing and certification. 6. Decouple the power cord at the power cord interface with decoupling capacitors. Methods to decouple power lines are similar to decoupling telephone lines. 7. Locate high frequency circuits in a separate area to minimize capacitive coupling to other circuits. 8. Locate cables and connectors so as to avoid coupling from high frequency circuits. 9. Lay out the highest frequency signal traces next to the ground grid. 10. If a multilayer board design is used, make no cuts in the ground or power planes and be sure the ground plane covers all traces. 11. Minimize the number of through-hole connections on traces carrying high frequency signals. 12. Avoid right angle turns on high frequency traces. Forty-five degree corners are good; however, radius turns are better. 13. On 2-layer boards with no ground grid, provide a shadow ground trace on the opposite side of the board to traces carrying high frequency signals. This will be effective as a high frequency ground return if it is three times the width of the signal traces. 14. Distribute high frequency signals continuously on a single trace rather than several traces radiating from one point. Electrostatic Discharge Control All electronic devices should be handled with certain precautions to avoid damage due to the accumulation of static charge. See the ANSI/ESD Association Standard (ANSI/ESD S20.20-1999) – a document “for the Development of an Electrostatic Discharge Control for Protection of Electrical and Electronic Parts, Assemblies and Equipment.” This document covers ESD Control Program Administrative Requirements, ESD Training, ESD Control Program Plan Technical Requirements (grounding/bonding systems, personnel grooming, protected areas, packaging, marking, equipment, and handling), and Sensitivity Testing. Multi-Tech Systems, Inc. strives to follow all of these recommendations. Input protection circuitry has been incorporated into the Multi-Tech devices to minimize the effect of this static buildup, proper precautions should be taken to avoid exposure to electrostatic discharge during handling. Multi-Tech uses and recommends that others use anti-static boxes that create a faraday cage (packaging designed to exclude electromagnetic fields). Multi-Tech recommends that you use our packaging when returning a product and when you ship your products to your customers. Phone Line Warning Statement for the Developer Board Use extreme caution when the phone line is installed due to live energized components. In fact, do not touch any components on the board while the phone line is installed. In addition, the phone line should be detached when making modifications to or servicing the developer board. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 17 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Comment [DAR9]: Mechanical Drawing for Analog Modems from Dean 4-16-09.png Mechanical Drawing in Inches for the Listed Products Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 18 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Comment [DAR10]: Mechanical Drawing for Analog Modems-Metric from Dean 4-16-09.png Mechanical Drawing in Millimeters for Listed Products Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 19 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Maximum Component Height / PCB Length and Width This is a companion table for the mechanical drawings on the two previous pages. If a product does not appear in this table, it is because it has a detailed mechanical drawing that provides this information and much more in the specific product chapter. Product Maximum Component Height on the Top Side of the Board Maximum Component Height on the Bottom Side of the Board Length Width SocketModem – MT9234SMI .290" (7.366 mm) .115" (2.921 mm) 2.54" (64.541 mm) 1.045" (26.543 mm) SocketModem – MT5692SMI .213" (5.410 mm) .115" (2.921 mm) 2.54" (64.541 mm) 1.045" (26.543 mm) SocketModem – MT2492SMI .177" (4.495 mm) NA 1.045" (26.543 mm) SocketModem IP – MT2456SMI-IP .228" (5.791 mm) .114" (2.895 mm) 2.54" (64.541 mm) 1.045" (26.543 mm) SocketEthernet IP – MT100SEM-IP .341" (8.661 mm) .115" (2.921 mm) 2.54" (64.541 mm) 1.045" (26.543 mm) Embedded Analog SocketModems 2.54" (64.541 mm) Embedded Device Servers SocketWireless Bluetooth – MTS2BTSMI .089" (2.260 mm) NA 2.54" (64.541) mm) 1.045" (26.543 mm) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 20 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity SocketModem Developer Board This developer board drawing shows the major board components for all SocketModems. Board Revision B See the next page for description of Board Components Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Comment [DAR11]: Board B for Universal 260b0_forRev J jumper fixed 2 29grayscale50percent.gif done 8/5/09 21 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Board Components Jumper JP1 JP2 Description Mutes the speaker. Default positions are 1 and 2 (speaker is not muted). Ties the TX and RX clock lines together. Default positions are 1 and 2 (transmit and receive clock act independently). Sets the data rate. NORMAL sets the data rate at 250kbps. H.S. (high speed serial communications) sets the data rate at 1Mbps. Testing interface (debugging) for the RS-232 signals. JP5 acts as a replacement for pin 45 when pin 45 is used for another function. Testing interface (debugging) for the serial TTL signals. JP9 is the 5V / 3.3V regulator. The factory default operating voltage is 3.3V. Warning – Be sure that the 5V / 3.3V jumper is set to match the requirements of your SocketModem. If this jumper is set incorrectly, damage to the SocketModem and/or the Test/Demo card could result. Caution – Use only the provided Multi-Tech Systems, Inc. transformer with the Test/Demo board. Use of any other power source will void the warranty and will likely damage the Test/Demo board and the SocketModem. The transformer connector is keyed to prevent improper connection to the Test/Demo board. JP12 allows you to select either the internal 5V regulator (INT 5V) or to choose EXT 5V. For the EXT 5V, you can use your own external 5V power source and plug it into J7. Set either 5V or 3.3V for USB_VBUS line (supplied by the VCC of the USB jack). Internal testing. JP15 disconnects pin 45 from SLP with JP5 (the RS-232 driver sleep mode). JTAG header. Mosquito header. If used to debug the SocketModem while using the USB port, then the JP14 would have to be removed to disconnect USB_VBUS. Power feed for area where SocketModems are placed (J24). Debugging probes. Ground lug. Set the switch block to the product being used. Reset JP3 JP4 JP5 JP7 JP9 JP12 JP13 JP14 JP15 JP16 JP17 JP18 JP19 & JP20 JP25 & JP26 S4 S5 Jumpers and Corresponding Signals J4 and J7 10 PWR CTS DSR DTR RXD RXC RI RTS GND TXD DCD J2 and J13 TXC JP10 JP11 TX Term RX Term Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 22 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Comment [DAR12]: C:\ Universal SocketModem\Graphics ETC Rev I\Block diagram board B\Block diagram board B w antenna.png. 38 KB SocketModem Developer Board Block Diagram Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 23 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Developer Board Schematics Comment [DAR13]: Schematics Board B page 2 Scan0576_000.jpg did not change to gif -- file was already small Board Revision B Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 24 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Developer Board Schematics Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 25 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Board Revision B Developer Board Schematics Board Revision B Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 26 Comment [DAR14]: Schematics Board B page 3 Scan0577_000 grayscale50percent.gif (changed from jpg to make the file size smaller 8/5/09) Comment [DAR15]: Schematics Board B page 4 Scan0575_000grayscale.gif (was jpg - now a gif for a smaller file 8/5/09 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Developer Board Schematics Board Revision B Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 27 Comment [DAR16]: Schmatics Board B page 5 Scan0574_000grayscale50percent.gif (was jpg but file was too large. Now gif 8/5/09) Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Developer Board Schematics Comment [DAR17]: Schematics Board B page 6 Scan0573_000.jpg did not change to gif -- file was aleady small Board Revision B Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 28 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Upgrading Firmware Your modem is controlled by semi-permanent firmware, which is stored in flash memory. Multi-Tech's firmware is nonvolatile; that is, it remains stored in memory when the modem is turned off and can be upgraded as new features are added. Multi-Tech's Flash Wizard can be downloaded from Multi-Tech’s FTP site and is available on CD. Use this Flash Wizard for upgrading your firmware. Documentation for using the Flash Wizard is included with the wizard. The following table shows you which products support the Flash Wizard. Wireless SocketModems SocketModem GPRS MTSMC-G2 Do not use the Flash Wizard for the wireless modems. Contact Multi-Tech for wireless modem firmware upgrade directions. SocketModem CDMA MTSMC-C1 Do not use the Flash Wizard for the wireless modems. Contact Multi-Tech for wireless modem firmware upgrade directions. SocketModem EDGE MTSMC-E1 Do not use the Flash Wizard for the wireless modems. Contact Multi-Tech for wireless modem firmware upgrade directions. SocketWireless HSDPA Do not use the Flash Wizard for the wireless modems. Contact Multi-Tech for wireless modem firmware upgrade directions. Analog SocketModems SocketModem MT9234SMI Flash Wizard Software for Windows®, Mac OSX, Linux Multi-Tech Flash Protocol SocketModem MT5692SMI and SocketModem MT5692SMI-IP Flash Wizard Software for Windows®, Mac OSX, Linux Can use ASCII upload via terminal emulator. SocketModem MT2492SMI No Flash Upgrade. Embedded Device Servers SocketEthernet IP MT100SEM-IP Flash Wizard Software for Windows®, Mac OSX, Linux Can use ASCII upload via terminal emulator. SocketWireless Wi-Fi MT810SWM-IP XMODEM serial port upgrade. See the next page for information about using the XMODEM upgrade. SocketWireless Bluetooth MTS2BTSMI Do not use the Flash Wizard for the wireless modems. Contact Multi-Tech for wireless modem firmware upgrade directions. Flash Wizard Software for Windows®: ftp://ftp.multitech.com/Utilities/FlashWizard/ Flash Wizard Software for Linux: http://mtflashwiz.sourceforge.net/ Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 29 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity XMODEM Serial Port Upgrade Comment [DAR18]: Removed all direct references to the SocketEthernet IP. Kevin said this applies to these 2 products 8/09 This upgrade procedure applies only to the MT810SWM-IP and the older product MTXCSEM. The IP communications device, for example, contains a 2 MB flash wherein the boot image, the firmware and configuration files are stored in a compressed format. The flash can easily be upgraded both locally as well as remotely. Serial Port Upgrade The flash of the can be upgraded locally through serial port using the upload feature of serial applications. Serial Port Configuration The default serial port parameters should be: Data length – 8 bits Parity – None Stop bits – 1 Baud-rate of the serial port to which the communications device is connected should be set to 115200 bps for proper operation. Example of a Serial Flash Upgrade Following steps explain the procedure to upgrade a flash using the serial COM port (serial flash upgrade). Connect the communications device to a PC COM Port. • • • • • • • Open an application through which we can access the serial device (e.g., Meterm, zoc, hyperterm). Reboot the communications device. Wait for the boot message and prompt “press d to download” to appear. Press d when prompted. Select the XMODEM Protocol from the Terminal application. Choose a file to be uploaded. Perform a file upload. The communications device reboots and will be up after a few seconds (10-15 seconds). Comment [DAR19]: Removed "TFTP Ethernet Upgrade" section. Darrick said it applied only to the MTXCSEM which this manual no longer covers. Caution: Refrain from powering off the device during flash upgrade. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 30 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Multi-Tech Systems, Inc. Flash Programming Protocol This information is provided exclusively for the users of Multi-Tech Systems, Inc. SocketModems, specifically the MT9234SMI. Multi-Tech Systems, Inc. SocketModem owners have the right to use, modify, and incorporate this code into other products provided they include the Multi-Tech Systems, Inc. notice and the associated copyright notice with any such product. Copyright (C) Multi-Tech Systems, Inc. 1995 All Right Reserved The flash programming protocol is provided "AS IS” without warranty. Important: When interacting with the boot code, it is possible to make the modem inoperable. Use extreme caution. Programming the Modem There are two ways to start flash programming a modem. It can be programmed 1. From “AT” mode 2. When the modem powers up. The following table shows how a modem is programmed. DTE Modem Comments AT*FS\r Handshake Sequence This effectively “restarts” the modem so that it enters the boot code. M’s Many M’s are sent (10 milliseconds apart) at 19200 baud. This is where the handshake starts if the modem is just powered up. U is sent at 19200 baud if M’s are received within 100 milliseconds of power up. If the M’s are not received within 100 milliseconds, then the modem starts up normally. If the AT*FS command is used, then you have 1 second (1000mS) to perform the handshake. Sent at 19200 baud. M if can receive at 9600/19200/38400/57600/115200 I if modem will be programmed at 9600 J if modem will be programmed at 19200 K if modem will be programmed at 38400 L if modem will be programmed at 57600 M if modem will be programmed at 115200 Modem is ready to be programmed I|J|K|L|M \r\nOK\r\n Program Sequence: DTE Modem ATFLP\r [Length High] [Length Low] [Address High] [Address Middle] [Address Low] [Data Bytes] Low byte of data packet length Packet lengths can be up to 4096 bytes in size for most boot code versions High byte of program address Middle byte of program address [Checksum] \nOK\r\n \nERROR\r\n …. ATFLEND\r Comments Request to the modem to program Modem is ready for next program packet High byte of data packet length …. Low byte of program address Addresses are 3 byte values with a range of 00000h-FFFFFh These are the data bytes to be programmed at the address specified above. They must be the same number of bytes as specified above. This checksum is generated by exclusive ORing together all of the Data Bytes (do not include the Length or Address bytes in that calculation). If bytes are programmed and verified. If verify fails or checksum is bad. Retry the block 3 times on an ERROR. More of the above sequence until all the data bytes have been sent to the modem. This ends programming and restarts the modem. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 31 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Other Supported Boot Code Commands 2.1 2.2 ATI0 ATI1 - ATI4- returns 000 or 247 for ISDN returns boot code version number MM.mmn where MM = unique code for each different platform that has boot code mm = version number of boot code n = version letter of the boot code Examples: 2.05e, 2.12d, 35.15 Boot code date and time. Other Programming Concerns 1. 2. 3. 4. 5. The packets sent to the modem must be presorted by address and aligned on 128 byte boundaries (i.e., each packet must start on an address that is a multiple of 128). The packets should also be a minimum of 128 bytes with the non-programmed bytes set to the hex value of FF. The packets sent to the modem must not span a 4K boundary (i.e., start the packet before it and go over the boundary in the middle of the packet). The 10-millisecond delay between M’s at the beginning of the handshake is so that the modem can sync up to the start bit. If the M’s are sent one right after another, a data bit might be mistaken as a start bit. Multi-Tech firmware files are in Intel Hex Format and must be read in and formatted into 128-4096 byte blocks before being sent to the modem. Information about the Intel Hex Format An Intel Format Hex File is a text file consisting of “records”, one per line, that start with a “:” character and include only digits 0-9 and letters A-F. There are three different record types: Extended Address Records, Data Records, and End of File Records. Data records contain the actual data that is to be programmed into a device. The address contained in the data record needs to be combined with an extended address (by adding the extended address shifted four bits left to the data record address) to determine the actual programming address for the data. If no extended address record is before a given data record in the file, then the extended address value is assumed to be zero. Data Record Char Pos Field Type Value Description Record Start “:” 2-3 Data Byte Count “NN” Maximum value is FF (which is 255 data bytes). Typical is 20h which causes the hex record to fit in 80 columns. 4-7 Address “XXXX” Lower 16 bits of 20 bit address, most significant byte first. This must be added to Extended Address left shifted four bits. 8-9 Record Type “00” Data Record 10+N Data Bytes “YY..YY The data bytes in hex. Each byte is two characters. ” NN+1,2 Checksum “ZZ” Zero minus the two’s complement addition of all data hex values. NN+3,4 End of Line “\r\n” Carriage Return followed by a Line Feed Example Data Record in Intel Format :2000A0005BB66DDBB66CD8B060C183060D1B366DDBB66DDBB76FDFBF7EFDFBF6EDDBB66DD4 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 32 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Extended Address Record Char Field Type Value Description Pos Record Start “:” 2-3 Data Byte Count “02” Always 2 bytes for this record type 4-7 Address “0000” Not used for this record type (must be zero) 8-9 Record Type “02” Extended Address Record 10-13 Extended Address “EEEE” Top 16 bits of 20 bit address, most significant byte first 14-15 Checksum “ZZ” Zero minus the two’s complement addition of all data hex values 16-17 End of Line “\r\n” Carriage Return followed by a Line Feed Example Extended Address Record in Intel Format :020000021000EC End of File Record Char Field Type Value Description Pos Record Start “:” 2-3 Data Byte Count “00” Always 2 bytes for this record type 4-7 Address “0000” Transfer Address (usually be zero) 8-9 Record Type “01” End of File Record 10-11 Checksum “ZZ” Zero minus the two’s complement addition of all data hex values 12-13 End of Line “\r\n” Carriage Return followed by a Line Feed Example End of File in Intel Format :00000001FF Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 33 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Wireless Information Antenna System for Wireless Devices The antenna system for use with Multi-Tech modems built into your products must include a coax cable to interface between UFL or MMCX connection on the modem and the antenna itself. RF Specifications GSM/EGSM RF Specifications GSM 850 Frequency RX Frequency TX RF Power Stand EGSM 900 GSM 1800 GSM 1900 869 to 894 MHz 925 to 960 MHz 1805 to 1880 MHz 824 to 849 MHz 880 to 915 MHz 1710 to 1785 MHz 2W at 12.5% duty cycle 2W at 12.5% duty cycle 1W at 12.5% duty cycle 1930 to 1990 MHz 1850 to 1910 MHz 1W at 12.5% duty cycle CDMA RF Specifications Frequency RX Frequency TX CDMA 800 CDMA 1900 869 to 894 MHz 824 to 849 MHz 1930 to 1990 MHz 1850 to 1910 MHz The Antenna GSM Antenna Requirements/Specifications Frequency Range Impedance VSWR Typical Radiated Gain Radiation Polarization Wave Cable Loss 824 – 960 MHz / 1710 – 1990 MHz 50 Ohms VSWR shall not exceed 2.0:1 at any point across the bands of operation 0 dBi on azimuth plane Omni-directional Vertical Half Wave Dipole The cable loss shall be such that the total radiate power (TRP) at the antenna shall be no less than +22/24.5 dBm for 850/1900 MHz respectively, and the total isotropic sensitivity (TIS) at the antenna shall be no less than -99/101.5 dBm for 850/1900 MHz respectively. GPS (Global Positioning) Antenna Requirements/Specifications Frequency 1575MHz Impedance VSWR Input voltage Connection 50 Ohms 2.0db 3.0V +/- 0.3V SMA Antennas Available from Multi-Tech Quad Band Description Hinged Right Angle 800/900/1800/1900 MHz Cellular Modem Antenna Hinged Right Angle 800/900/1800/1900 MHz Cellular Modem Antenna Hinged Right Angle 800/900/1800/1900 MHz Cellular Modem Antenna Dual Band Description Hinged Right Angle 900/1800 MHz Cellular Modem Antenna Hinged Right Angle 900/1800 MHz Cellular Modem Antenna Hinged Right Angle 900/1800 MHz Cellular Modem Antenna Hinged Right Angle 800/1900 MHz Cellular Modem Antenna Hinged Right Angle 800/1900 MHz Cellular Modem Antenna Hinged Right Angle 800/1900 MHz Cellular Modem Antenna Bluetooth and Wi-Fi Hinged 2.4 MHz Bluetooth / Wi-Fi Antenna Hinged 2.4 MHz Bluetooth / Wi-Fi Antenna Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Qty 10 50 Qty 10 50 10 50 Qty 10 Part Number ANQB-1HRA ANQB-10HRA ANQB-50HRA Part Number ANF1-1HRA ANF1-10HRA ANF1-50HRA ANCF2-1HRA ANCF2-10HRA ANCF2-50HRA Part Number ANBT-1 ANBT-10 34 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Coax Cables Comment [DAR20]: Adapter_Amph enol.gif MMCX-to-SMA and MMCX to RSMA Coax Cable This cable shown below is included in the Developer Kit for the CDMA, EDGE SocketModems, and the SocketWireless Bluetooth. Cable Specifications Cable Type: Attenuation: Connector Impedance: Coax Cable <1.0db 50 Ohms Comment [DAR21]: Now new from Dean. (was Wireless Antenna Cable from Ken 20903C_cable only.jpg Wireless Antenna Cable from Ken_20903c_generic.FH9f Wireless Antenna Cable from Ken_20903c_generic.pdf) An optional antenna cable (SMA to MMCX) can be ordered from Multi-Tech Systems, Inc. Part Number Description CASMA-MMCX-1 SMA to MMCX COAX RF 6 inch cable (Single Pack) CASMA-MMCX-10 SMA to MMCX COAX RF 6 inch cable (Ten Pack) MMCX-to-SMA Adapter An antenna with an SMA connector may be directly connected to a SocketModem GPRS/CDMA through a mating MMCX-to-SMA adapter. SMA-to-MMCX Connector Available from Amphenol Amphenol http://www.amphenol.com/ Order No: 908-31100 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 35 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity UFL-to-SMA and UFL-to-RSMA Coax Cable The UFL-to-SMA cable is included in the Developer Kit for the GPS (Global Positioning), GPRS and HSDPA SocketModems. Cable Specifications Cable Type: Attenuation: Connector Impedance: Coaxial Cable <1.0db 50 ohm Comment [DAR22]: Now new from Dean SocketModem_SS_Auxiliary Cable. PNG 2/4/2009 An optional antenna cables can be ordered from Multi-Tech Systems, Inc. Part Number Description CASMA8-UFL-1 SMA to UFL COAX RF 8 inch cable (Single Pack) CASMA8-UFL-10 SMA to UFL COAX RF 8 inch cable (Ten Pack) CARSMA8-UFL-1 RSMA to UFL COAX RF 8 inch cable (Single Pack) CARSMA8-UFL-10 RSMA to UFL COAX RF 8 inch cable (Ten Pack) PTCRB Requirements for the Antenna There cannot be any alteration to the authorized antenna system. The antenna system must be the same type with similar in-band and out-of-band radiation patterns and maintain the same specifications. FCC Requirements for the Antenna The antenna gain, including cable loss, must not exceed 3.0 dBi at 1900 MHz / 1.6 dBi at 850 MHz for mobile operating and fixed mounted operations, as defined in 2.1091 and 1.1307 of the rules for satisfying RF exposure compliance. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 36 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Account Activation for Wireless Devices Pre-Configured Multi-Tech Products Some Multi-Tech wireless modems have been pre-configured to operate on a specific wireless network, such as Sprint and Verizon. However, before you can begin to use the modem, you must set up a wireless data account with your wireless network provider. Then, follow the activation procedures covered on the Activation Notices available from Multi-Tech. Wireless Approvals and Labeling Requirements Approvals and Certification The Multi-Tech SocketModem is Industry and/or Carrier Approved as an End Product modem. In most cases, when integrated and used with an antenna system that was part of the Multi-Tech modem certification, no additional approvals or certifications are required (however, CDMA has a few exceptions) for the device you develop as long as the following are met: • PTCRB Requirements: The antenna system cannot be altered. • Model Identification: IMPORTANT When the wireless carrier asks you to provide the modem's model identification, give the Multi-Tech wireless model identification, not the identification of the host device model. See the label example below. The Multi-Tech model identification allows the carrier to verify the modem as one of its approved models. This information is located on the modem's label. Comment [DAR23]: Now Label F4.png saved in Graphics new in Rev 62kb The Following Is an Example of an End Product GPRS Label: Host Device Model Identification Multi-Tech SocketModem Model Identification IMEI (International Mobile Equipment Identity) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 37 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Comment [DAR24]: Label SmallC.png 23KB 6/16/09 The Following Is an Example of an End Product CDMA Label: Multi-Tech Model Identification Multi-Tech Ordering Part Number ESN: Electronic Serial Number in Hexadecimal Format and Decimal Format • Other Information the Wireless Carrier Asks You to Provide: For CDMA SocketModems: The modem's 8-character ESN (Electronic Serial Number) number printed next to the barcode on the modem. The ESN may vary in format by various CDMA carriers; some use a decimal number while others use a hexadecimal number. For GSM SocketModems: The modem's 15-character IMEI (International Mobile Equipment Identity) number printed on the modem's label. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 38 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Analog Information Recommended Parts for Analog SocketModems Disclaimer: Multi-Tech Systems makes no warranty claims for vendor product recommendations listed below. Other vendor products may or may not operate satisfactorily. Multi-Tech System’s recommended vendor products only indicate that the product has been tested in controlled conditions and were found to perform satisfactorily. Surface mount ferrites are used on T&R (Tip and Ring) to mitigate emission levels out the RJ-11 cable. 220pF capacitors are also used on T&R to reduce the common mode emissions that may be present in certain systems. See the Tip and Ring drawings in each analog SocketModem chapter. The ferrite and capacitors also aid in reducing the effects of transients that may be present on the line. Note: These parts are RoHS compliant. Recommended Ferrite (SMT) Manufacturer – Associated Component Technology (ACT) Part # CBZ1206-202-30-LF Manufacturer – Murata Erie Part # BLM31AJ601SN1L Recommended Ferrite (Thru-Hole) Manufacturer – Associated Component Technology (ACT) Part # WB2-2.OT Recommended Capacitor (SMT) Manufacturer – NOVACAP Manufacturer – Murata Erie Part # ES2211N221K502NXT Part # GA355DR7GC221KY02L Recommended Capacitor (Thru-Hole) Manufacturer – Ever Grace Electronic Industrials Part # YP221K2EA7PS-8.0 Manufacturer – Murata Erie Part # DE2B3KH221KA3B Note: Capacitors used on T&R must have the Y2 safety rating. Recommended RJ-11 Connector Manufacturer – Full Rise Electronic Co. Part # E5964-00P045 Recommended Sidactor Manufacturer – RayChem / Tyco Electronics Manufacturer – ST Microelectronics Part # TVB400MSC-L Part# SMPMC-400 Recommended Poly Switch Thermal Fuse (SMT) Manufacturer – RayChem / Tyco Electronics Part # TS600-170F Recommended Poly Switch Thermal Fuse (Thru-Hole) Manufacturer – RayChem (Tyco Electronics) Part# TRF600-150 Note: The Fuse & Sidactor are required in order to comply with UL60950 for protection against over-voltages from power line cross. Fuse can be reset type. Common Mode Choke Manufacturer – TDK Part # ZJYS51R5-2PT-01 Recommended Transceiver Manufacturer – Analog Devices Part # ADM207EARZ SIP Connector Manufacturer – Neltron Industrial Co. (http://www.neltron.com.tw/) Part #2209S-xxSG 4-Pin 2.0mm SIP Socket (2 Each) 10-Pin 2.0mm SIP Socket (2 Each) Telecom The RJ-11 connector must meet FCC Part 68 requirements. Refer to FCC Part 68 section 68.500 subpart F for connector specifications. A self-healing fuse is used in series with line to help prevent damage to the DAA circuit. This fuse is required in order to meet compliance regulations. Note: See Application Notes at the end of each SocketModem chapter. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 39 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Analog Labeling Requirements United States Labeling Requirements (for Dial-Up Modems) Telecom does not apply to all products. For example, this is not applicable for the SocketModem GPRS and CDMA products. Approved terminal equipment and approved protective circuitry shall prominently display the following information using the format shown below: • Responsible party • Product Identification • Equipment Code • Ringer Equivalence • Ringer Type • Indication that the product meets the requirements of FCC Part 68 The information required by the first five items shall correspond to the records in the ACTA (America's Carriers Telecommunications Association) database of approved equipment. The required information shall be encoded in the following format: US: AAAEQ##TXXX Where: US: Is a fixed field that indicates the equipment meets all requirements of 47 CFR Part 68, including the requirements published by ACTA (America's Carriers Telecommunications Association). AAA is the responsible party’s Grantee Code obtained previously from the FCC’s Common Carrier Bureau or currently from ACTA. EQ Is an Equipment Code indicating to the Service Provider any special signal handling or billing requirements. The Equipment codes are listed in Annex A (normative). ## is the Ringer Equivalence Number without a decimal point (e.g. REN of 1.0 = 10, REN of 0.3 = 03). In the case of a “Z” ringer, ZZ shall appear. In the case of approved equipment without a network interface and equipment not connecting to circuits with analog ringing supplied then “NA” shall appear. T is the ringer type letter associated with the Ringer Equivalence Number, in accordance with the technical requirements. In the case of approved equipment without a network interface and equipment not connecting to circuits with analog ringing supplied, the letter “N” shall appear. XXX Is a product identifier, unique when combined with the responsible party’s Grantee Code, of at least one and up to nine alphanumeric characters (including one or more dashes (-) if desired. A dash shall not appear as the first or last character nor shall the identifier consist entirely of dashes). The responsible party shall define this identifier. Label Physical Characteristics The information required above shall be permanently affixed and legible without magnification. It may be etched, engraved, stamped, indelibly printed, or otherwise permanently marked. Alternatively, the required information may be permanently marked on a nameplate of metal, plastic or other material fastened to the enclosure by welding, riveting or with a permanent adhesive. Such a nameplate shall be able to last for the expected lifetime of the equipment and shall not be readily detachable. Labeling Continuity and Changes The labeling content and format requirements in effect when a product was approved shall be effective for the life of the product. The labeling content and format requirements in effect at approval shall also continue to be effective for modified products. However, the responsible party shall have the option of conforming a product's labeling to current content and format requirements at any time. Other Label Requirements The label shall be placed in one of the following locations in a location where it can be found after installation: • on an outside surface • inside a readily available access door or panel • on another readily accessible surface For example, the label should not be placed on the rear of a permanently wall-mounted device in a manner such that it is not readily accessible. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 40 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Canadian Labeling Requirements (for Dial-Up Modems) The following requirements are established under section 69.3 of the Telecommunications Act for purposes of section 5 of the Telecommunications Apparatus Regulations. Registered equipment shall bear the following identifying marks, and the Declaring Party shall ensure that these marks are permanently affixed to the equipment: (a) The registration number — Specifications of this mark are given in the document: Self-Marking of the Certification/Registration Number on Terminal Equipment — Application Procedure and Agreement; and (b) The model identification number under which the product was registered. A statement of compliance with Industry Canada requirements, such as the one given below, shall accompany each unit of equipment whether registered under this procedure or previously certified: "This product meets the applicable Industry Canada technical specifications" For terminal equipment intended for connection to loop-start or ground-start interfaces, the Ringer Equivalence Number (REN) must be calculated as per Section 1.8 of CS-03, Part I. A REN higher than that determined may be assigned by manufacturers to allow for production variations. The REN must be marked on the terminal equipment itself or added to the note below. A note similar to the following shall accompany each unit of equipment whether registered under this procedure or previously certified: "The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five". Pursuant to section 69.3 of the Telecommunications Act, certified or self-declared TE will bear a valid identifying certification number or registration number. The marking of the certification or registration number on the product shall be as follows: (a) TAC holder/DP will be responsible for permanently affixing the certification/registration number on the TE. The certification/registration number (see example below) identifies Certified or self-declared TE to the public, representatives of the telecommunications common carriers, the Department, and other interested parties. The letter height must be no less than 1.5 mm and the letters must be legible without magnification. (b) For integrated devices, e.g. a modem or one that is intended to become a sub-assembly of host equipment e.g. a data terminal, computer etc. that are designed to interface directly with the network, the certification/registration number shall be affixed to the integrated device itself. (c) The certification/registration number for a packaged TE will denote that the total package has been registered. However, the marking will normally be placed on that unit of the package which connects to the network; e.g., in a PBX the marking will be placed on the common equipment which connects to the network, rather than on plug-in components which may be added later. The Terminal Equipment List will show the common equipment but not the standard station apparatus or any proprietary station apparatus. (d) The marking format of the certification/registration number is as follows: IC: XXXXXX-YYYYYYYY Where: • The letters "IC" have no other meaning or purpose than to identify the Industry Canada certification/registration number, and • “XXXXXX-YYYYYYYY” is the certification/registration number; “XXXXXX” is the Company Number¹ (CN); it consists of up to six alphanumeric characters (A-Z, 0-9) assigned by Industry Canada; and “YYYYYYYY” is the Unique Product Number (UPN); it consists of up to eight alphanumeric characters (AZ, 0-9) assigned by the applicant. Other characters, (such as & # *-) may not be used. Alphabetic characters must be capitalized. ¹ Note: The Company Number of registered equipment ends with an alphabetic character. (e) Certification Numbers granted prior to the implementation of the above marking format are grandfathered. (i) For previously certified TE, the self-marking format shall consist of the old certification number preceded by “IC:” For example, if the certification number is “123 1234 A”, then the self-mark would read “IC: 123 1234 A”. (ii) For a new model that is registered to a family of previously certified TE, the self-marking format shall be: IC: XXXXXX-ZZZZZZZZ Where: • “XXXXXX” is the Company Number, as in (d) above; and • “ZZZZZZZZ” is either the old certification number minus the old company number, or a new Unique Product Number assigned by the applicant. For example, if a new model is registered to the family of products with certification number “123 1234 A”, and that the Company Number for the registration is “123A”, then the self-mark for this new model would read “IC: 123A-1234 A”. If the applicant decides to replace “1234 A” with a new UPN, say “5678", then the self-mark would read “IC: 123A-5678". Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 41 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Label Examples for Analog SocketModems Comment [DAR25]: Label Small MT9234SMI.png 6/16/09 Label 9234SMI Scan0549_000.png 6/16/09 Note: These do not apply to the Wireless GPRS and CDMA products. Serial Label This label shows the modem model (M/N), build option (B/O), date of manufacture (DOM), serial number, and North America and European Union regulatory information. Comment [DAR26]: Label 9234SMI Scan 0549_000.png 55KB 6/15/09 This is an example of Regulatory Label which is available from Multi-Tech by request. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 42 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Safety Notices and Warnings Note to OEMs: The following safety statements may be used in the documentation of your final product applications. Wireless Safety General Safety The modem is designed for and intended to be used in fixed and mobile applications. “Fixed” means that the device is physically secured at one location and is not able to be easily moved to another location. “Mobile” means that the device is designed to be used in other than fixed locations. RF Safety The remote modems are wireless cellular telephones devices. It is important to follow any special regulations regarding the use of radio equipment due in particular to the possibility of Radio Frequency (RF) interference. Caution: A separation distance of at least 20 cm must be maintained between the modem transmitter’s antenna and the body of the user or nearby persons. The modem is not designed for or intended to be used in portable applications within 20 cm of the body of the user. In particular, if using a Yagi antenna, it must be in a location that prevents public exposure to the radiation limits being exceeded. Check your local standards regarding safe distances, etc. • Wireless modems in an ATM in, for example, a hospital environment and any other place where medical equipment may be in use, may be a hazard. This statement also applies to inadequately protected personal medical devices such as hearing aids and pacemakers. • Operation of a wireless modem close to other electronic equipment may also cause interference if the equipment is inadequately protected. Observe any warning signs and manufacturers’ recommendations. • The modems must not be operated around gasoline or diesel-fuel. RF Interference Safety It is important to follow any special regulations regarding the use of radio equipment due in particular to the possibility of radio frequency, RF, interference. Please follow the safety advice given below carefully. • Switch OFF your Wireless MultiModem when in an aircraft. The use of cellular telephones in an aircraft may endanger the operation of the aircraft, disrupt the cellular network and is illegal. Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender, or legal action or both. • Switch OFF your Wireless MultiModem when around gasoline or diesel-fuel pumps and before filling your vehicle with fuel. • Switch OFF your wireless device in hospitals and any other place where medical equipment may be in use. • Respect restrictions on the use of radio equipment in fuel depots, chemical plants or where blasting operations are in progress. • There may be a hazard associated with the operation of your wireless device close to inadequately protected personal medical devices such as hearing aids and pacemakers. Consult the manufacturers of the medical device to determine if it is adequately protected. • Operation of your wireless device close to other electronic equipment may also cause interference if the equipment is inadequately protected. Observe any warning signs and manufacturers’ recommendations. Vehicle Safety • Do not use your wireless device while driving. • Respect national regulations on the use of cellular telephones in vehicles. Road safety always comes first. • If incorrectly installed in a vehicle, the operation of a wireless telephone could interfere with the correct functioning of vehicle electronics. To avoid such problems, be sure that qualified personnel have performed the installation. Verification of the protection of vehicle electronics should be part of the installation. • The use of an alert device to operate a vehicle’s lights or horn on public roads is not permitted. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 43 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Maintenance of Your Wireless Device Your wireless device is the product of advanced engineering, design, and craftsmanship and should be treated with care. The suggestions below will help you to enjoy this product for many years. • Do not expose the wireless device to any extreme environment where the temperature is above 50ºC or humidity is above 90% noncondensing. • Do not attempt to disassemble the wireless device. There are no user serviceable parts inside. • Do not expose the wireless device to water, rain, or spilled beverages. It is not waterproof. • Do not place the wireless device alongside computer discs, credit or travel cards, or other magnetic media. The phone may affect the information contained on discs or cards. • The use of accessories not authorized by Multi-Tech or not compliant with Multi-Tech's accessory specifications may invalidate the warranty of the wireless device. • In the unlikely event of a fault in the wireless device, contact Multi-Tech Tech Support. Your Responsibility This wireless device is your responsibility. Please treat it with care respecting all local regulations. It is not a toy. Therefore, keep it in a safe place at all times and out of the reach of children. Try to remember your Unlock and PIN codes. Become familiar with and use the security features to block unauthorized use and theft. Analog Telecom Safety Warnings 1. 2. 3. 4. 5. 6. 7. 8. 9. Never install telephone wiring during a lightning storm. Never install a telephone jack in wet locations unless the jack is specifically designed for wet locations. This product is to be used with UL and cUL listed computers. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. Avoid using a telephone during an electrical storm. There may be a remote risk of electrical shock from lightning. Do not use a telephone in the vicinity of a gas leak. To reduce the risk of fire, use only 26 AWG or larger telecommunication line cord. This product must be disconnected from its power source and telephone network interface when servicing. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 44 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Telecom Approvals for Analog Modems Multi-Tech's Analog Global* SocketModems are designed and approved for connection to the public switched telephone network in more than 50 countries or regions worldwide. Multi-Tech's SocketModems have been approved as host independent, which means our certification efforts can be transferred directly to your end product with proper labeling on the OEM equipment. Multi-Tech supports our approvals by supplying our customers with supporting documentation and offering a compliance label with country or regional approval logos and approval numbers to be attached to an end product. The following is a list of countries or regions that Multi-Tech completes testing and obtains** certification test reports or certificates at or near the initial release of the product. After the initial release, the product may be tested and certified for other countries or regions. Check the Multi-Tech Systems, Inc. Web site at http://www.multitech.com/products/info/approvals/smi.asp or contact Multi-Tech at oemsales@multitech.com to obtain a current list of approvals for the SocketModem. Countries or Regions Argentina France Liechtenstein Singapore Australia Germany Lithuania Slovakia Republic Austria Greece Luxembourg Slovenia Belgium Hong Kong, S.A.R. of China Malta South Africa Bulgaria Hungary Mexico Spain Canada Iceland Netherlands Sweden Chile Indonesia New Zealand Switzerland China Ireland Norway Taiwan Cyprus Israel Philippines Thailand Czech Republic Italy Poland Turkey Denmark Japan Portugal United Kingdom Estonia Korea Romania United States Finland Latvia Russia The above list is our target set of countries or regions in which the global* SocketModems are approved. Many of the approvals are completed at the time the product is released to market; whereas, others may take additional months to complete the approval. Refer to each chapter for Product Ordering Information identifying the modem as Global or Regional. ** Some countries or regions have special import requirements that require us to facilitate additional paperwork application in partner with our customers. Contact Technical Support or Multi-Tech at oemsales@multitech.com for more information. Note: Setting Country/Regional Codes – Country or Regional Codes are usually set through AT Commands. See each product’s AT Command guide. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 45 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Regulatory Compliance Statements Country/Region-Specific Statements EMC, Safety, and R&TTE Directive Compliance The CE mark is affixed to this product to confirm compliance with the following European Community Directives: Council Directive 2004/108/EC of 15 December 2004 on the approximation of the laws of Member States relating to electromagnetic compatibility; and Council Directive 2006/95/EC of 12 December 2006 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits; and Council Directive 1999/5/EC of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. International Modem Restrictions Some dialing and answering defaults and restrictions may vary for international modems. Changing settings may cause a modem to become non-compliant with national telecom requirements in specific countries. Also note that some software packages may have features or lack restrictions that may cause the modem to become noncompliant. EMC Requirements for the United States 47 CFR – FCC Part 15 Regulation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 47 CFR – FCC Part 15 regulations. The stated limits in this regulation are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Plug the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with 47 CFR – FCC Part 15 rules. Operation of this device is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. EMC Requirements for Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Reglement Canadien sur le matériel brouilleur. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 46 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity 47 CFR Part 68 Telecom 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. This equipment complies with Part 68 of the 47 CFR rules and the requirements adopted by the ACTA. Located on this equipment is a label that contains, among other information, the registration number and ringer equivalence number (REN) for this equipment or a product identifier in the format: For current products is US:AAAEQ##Txxxx. For legacy products is AU7USA-xxxxx-xx-x. If requested, this number must be provided to the telephone company. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable 47 CFR Part 68 rules and requirements adopted by the ACTA. It’s designed to be connected to a compatible modular jack that is also compliant. The ringer equivalence number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##Txxxx. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment, please contact Multi-Tech Systems, Inc. at the address shown below for details of how to have the repairs made. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void registration and warranty. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. This equipment is hearing aid compatible. Manufacturing Information on telecommunications device (modem): Manufacturer: Multi-Tech Systems, Inc. Trade Name: Socket Modem SocketModem SocketModem Model Number: MT9234SMI MT5692SMI MT2492SMI Registration No: US:AU7MM01BMT9234SMI US:AU7MM01BMT5692SMI US:AU7MM01B2492SMI Ringer Equivalence: 0.1B Modular Jack (USOC): RJ11C or RJ11W (single line) Service Center in USA: Multi-Tech Systems, Inc. 2205 Woodale Drive Mounds View, MN 55112 U.S.A. (763) 785-3500 (763) 785-9874 Fax Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 47 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity New Zealand Telecom Warning Notice 1. 2. 3. 4. 5. 6. 7. 8. The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. This equipment is not capable under all operating conditions of correct operating conditions of correct operation at the higher speed which it is designated. 33.6 kbps and 56 kbps connections are likely to be restricted to lower bit rates when connected to some PSTN implementations. Telecom will accept no responsibility should difficulties arise in such circumstances. Immediately disconnect this equipment should it become physically damaged, and arrange for its disposal or repair. This modem shall not be used in any manner which could constitute a nuisance to other Telecom customers. This device is equipped with pulse dialing, while the Telecom standard is DTMF tone dialing. There is no guarantee that Telecom lines will always continue to support pulse dialing. Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to 'bell tinkle' or noise and may also cause a false answer condition. Should such problems occur, the user should NOT contact the Telecom Faults Service. The preferred method of dialing is to use DTMF tones, as this is faster than pulse (decadic) dialing and is readily available on almost all New Zealand telephone exchanges. Warning Notice: No '111' or other calls can be made from this device during a mains power failure. This equipment may not provide for the effective hand-over of a call to another device connected to the same line. Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom’s Specifications: For repeat calls to the same number: • There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and • The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt. For automatic calls to different numbers: • The equipment shall be set to ensure that automatic calls to different numbers are spaced such that there is no less than 5 seconds between the end of one call attempt and the beginning of another. For correct operation, total of the RN’s of all devices connected to a single line at any time should not exceed 5. South African Statement This modem must be used in conjunction with an approved surge protection device. Thailand Approval for MT9234SMI and the MT5692SMI This telecom device conforms to NTC* requirements. *NTC is the National Telecommunications Commission, Thailand’s telecommunications regulator. “เครื่องโทรคมนาคมและอุปกรณนี้ มีความสอดคลองตามขอกําหนดของ กทช.” Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 48 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Brazil Approval for the MT9234SMI and MT5656SMI This product has been homologated by ANATEL. This product meets the applied technical requirements in accordance with the procedures regulated by ANATEL. Reference of homologation of this product can be viewed in ANATEL web page: http://www.anatel.gov.br Brazil Bar Code for MT9234SMI Brazil Bar Code for MT5656SMI Brazil Certification (MT9234SMI Model Only) A special phone cable is required for regulatory compliance. Um cabo especial para telefone é requerido para a conformidade regulatória. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 49 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Japan Requirements These devices conform to (JATE) Japan Approval Institute for Telecommunications Equipment: MT5692SMI – JATE Approval A09-0123001 MT9234SMI – JATE Approval AD06-0220001 Important Note: SocketModems are approved for product development in Japan only if they are removable from the manufactured product. The SocketModem must not be soldered into place. Japan requires that your manufactured product documentation include SocketModem installation and removal instructions as well as connection to the PSTN network. The following text provides general steps to follow. Installation of the SocketModem from Your Manufactured Product 1. 2. 3. 4. If applicable, disconnect any power cord and peripherals you may have attached to your manufactured product. Place the SocketModem on the board of your product. Be sure to match the pins on the SocketModem with the correct orientation on your board. Be sure that the SocketModem is securely fastened to board so that it cannot come loose while handling or during shipping. Some examples of fasteners include nylon screws, tie wraps, etc. Remember that you cannot solder the SocketModem in place. Put the cover on your product and connect the power and peripherals. Removal of the SocketModem from your Manufactured Product 1. 2. 3. 4. 5. Back up the current configuration of your manufactured product if you want to save it. Record any information not stored in the configuration that you may want to reference. Disconnect any power cord and peripherals from your manufactured product. Remove the cover from your product. To remove the SocketModem, gently lift the SocketModem upwards while holding the board in place. Connecting to the PSTN Network For connection to a PSTN network, see the Tip and Ring Interface section in each analog SocketModem chapter. Other Countries The above country-specific examples do not cover all countries with specific regulations; they are included to show you how each country may differ. If you have trouble determining your own country's requirements, check with Multi-Tech's Technical Support for assistance. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 50 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Waste Electrical and Electronic Equipment Statement Note to OEMs: The statement is included for your information and may be used in the documentation of your final product applications. WEEE Directive The WEEE directive places an obligation on EU-based manufacturers, distributors, retailers, and importers to takeback electronics products at the end of their useful life. A sister Directive, ROHS (Restriction of Hazardous Substances) complements the WEEE Directive by banning the presence of specific hazardous substances in the products at the design phase. The WEEE Directive covers all Multi-Tech products imported into the EU as of August 13, 2005. EU-based manufacturers, distributors, retailers and importers are obliged to finance the costs of recovery from municipal collection points, reuse, and recycling of specified percentages per the WEEE requirements. Instructions for Disposal of WEEE by Users in the European Union The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product. July, 2005 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 51 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Comment [DAR27]: Stored in common text as png. 3KB Restriction of the Use of Hazardous Substances (RoHS) Multi-Tech Systems, Inc. Certificate of Compliance 2002/95/EC Multi-Tech Systems Inc. confirms that its embedded products now comply with the chemical concentration limitations set forth in the directive 2002/95/EC of the European Parliament (Restriction Of the use of certain Hazardous Substances in electrical and electronic equipment - RoHS) These Multi-Tech Systems, Inc. products do not contain the following banned chemicals: Lead, [Pb] < 1000 PPM Mercury, [Hg] < 1000 PPM Hexavalent Chromium, [Cr+6] < 1000 PPM Cadmium, [Cd] < 100 PPM Polybrominated Biphenyl, [PBB] < 1000 PPM Polybrominated Diphenyl Ether, [PBDE] < 1000 PPM Moisture Sensitivity Level (MSL) =1 Maximum Soldering temperature = 260C (wave only) Notes: 1. Lead usage in some components is exempted by the following RoHS annex; therefore, higher lead concentration would be found in some SocketModems (>1000ppm). a. Lead in high melting temperature type solders (i.e., tin-lead solder alloys containing more than 85% lead). b. Lead in electronic ceramic parts (e.g., piezoelectronic devices). 2. Moisture Sensitivity Level (MSL) – Analysis is based on the components/material used on the board. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 52 Comment [DAR28]: Bud said to take out the Tin Whisker growth statements 8/24/09. He had said this previously, but they somehow didn't get removed. Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Information on HS/TS Substances according to Chinese Standards in English In accordance with China’s Administrative Measures on the Control of Pollution Caused by Electronic Information Products (EIP) # 39, also known as China RoHS, the following information is provided regarding the names and concentration levels of Toxic Substances (TS) or Hazardous Substances (HS) which may be contained in Multi-Tech Systems Inc. products relative to the EIP standards set by China’s Ministry of Information Industry (MII). Hazardous/Toxic Substance/Elements Name of the Component Lead (PB) Mercury (Hg) Cadmium Hexavalent (CD) Chromium (CR6+) Polybrominated Polybrominated Biphenyl (PBB) Diphenyl Ether (PBDE) Printed Circuit Boards Resistors Capacitors Ferrite Beads Relays/Opticals ICs Diodes/ Transistors Oscillators and Crystals Regulator Voltage Sensor Transformer Speaker Connectors LEDs Screws, Nuts, and other Hardware ac-dc Power Supplies Software / Documentation CDs Booklets and Paperwork Chassis Represents that the concentration of such hazardous/toxic substance in all the units of homogeneous material of such component is higher than the SJ/Txxx-2006 Requirements for Concentration Limits. Represents that no such substances are used or that the concentration is within the aforementioned limits. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 53 Part 1 − Universal Socket Connectivity Chapter 1 – Universal Socket Connectivity Information on HS/TS Substances According to Chinese Standards in Chinese 依照中国标准的有毒有害物质信息 根据中华人民共和国信息产业部 (MII) 制定的电子信息产品 (EIP) 标准－中华人民共和国《电子信息产品污染控制管理办法》（第 39 号），也称作中国 RoHS，下表列出了 Multi-Tech Systems, Inc. 产品中可能含有的有毒物质 (TS) 或有害物质 (HS) 的名称及含量水平方面的信息。 有害/有毒物质/元素 铅 (PB) 汞 (Hg) 镉 (CD) 六价铬 (CR6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 电阻器 电容器 铁氧体磁环 继电器/光学部件 IC 二极管/晶体管 振荡器和晶振 调节器 电压传感器 变压器 扬声器 连接器 LED 螺丝、螺母以及其它 五金件 交流-直流电源 成分名称 印刷电路板 软件/文档 CD 手册和纸页 底盘 表示所有使用类似材料的设备中有害/有毒物质的含量水平高于 SJ/Txxx-2006 限量要求。 表示不含该物质或者该物质的含量水平在上述限量要求之内。 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 54 PART 2 – Embedded Wireless Modems Part 2 Wireless SocketModems Chapter 2 – SocketModem Cell and iCell Chapter 3 – SocketModem CDMA Chapter 4 – SocketModem EDGE Chapter 5 – SocketModem HSDPA Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 55 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Chapter 2 – SocketModem® Cell (MTSMCG2) & SocketModem® iCell (MTSMC-G2-IP) Introduction The MTSMC-G2 is a serial to wireless quad-band GPRS SocketModem. It is a complete, ready-to-integrate SocketModem that offers standards-based multi-band GSM/GPRS Class 10 performance. It is based on industry-standard open interfaces and utilizes Multi-Tech’s universal socket design. The SocketModem is available with the Multi-Tech's Universal IP™ stack to bring embedded Internet connectivity to any device. Notes about Activation: • • These units are shipped without network activation. To connect to the wireless network, you will have to establish a wireless account. See the Wireless Activation procedures on separate sheets included with the Developer Kit and available on the Developer Kit CD. Product Build Options and Ordering Information Product Description Region MTSMC-G2 MTSMC-G2-ED MTSMC-G2-V MTSMC-G2-V-ED MTSMC-G2-IP MTSMC-G2-IP-ED Quad-band GPRS SocketModem Cell Quad-band GPRS SocketModem Cell Quad-band GPRS SocketModem Cell with Voice Quad-band GPRS SocketModem Cell with Voice Quad-band GPRS SocketModem iCell with Universal IP Quad-band GPRS SocketModem iCell with Universal IP Developer Kit US Default EU Default US Default EU Default US Default EU Default MTSMI-UDK Universal Developer Kit Global Order This Product How to Read the Product Codes in the Table Above: G2 GPRS ED European Default Voice (microphone and speaker) IP Universal IP™ Stack UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MTSMC-G2.Rx. “R” indicates product revision. “x” is the revision number. Note: All products can be ordered in single packs or 50-packs. Single pack product codes end in SP. AT Commands Reference Guides Products AT Commands Reference Guide Title & Document Number GPRS AT Commands for Multi-Tech G2 Wireless Modems (S000463x) AT Commands for Multi-Tech G2 Wireless Modems with IP Connectivity (S000469x) SocketModem iCell GPRS AT Commands for Multi-Tech G2 Wireless Modems (TSMC-G2-IP) (S000463x) Universal IP Commands (S000457x) SocketModem Cell (MTSMC-G2 and MTSMC-G2-V ) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Fax Commands Voice Commands NA Included NA Included 56 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Technical Specifications The MTSMC-G2 and MTSMC-G2-IP SocketModems meet the following specifications: Category Description Standards Frequency Bands Serial/Data Speed Data Format Data Error Correction Data Compression Weight GPRS Class 10 Quad-band GSM/EGPRS 850/900/1800/1900 MHz Serial interface supports DTE speeds up to 921.6K IP interface supports DTE speeds at the fixed rate of 115.2 Packet data up to 85.6K bps Circuit-switched data (GPRS) up to 14.4K bps transparent and non-transparent Supports data rates of 921600, 460800, 230400, 115200 bps 10 bit Serial Asynchronous MNP2 V.42bis 1 oz. (28 g) Size 3.15" x 1.375" (80.010 mm x 34.925 mm) Operating Temperature -40° C to +85° C Storage Temperature Humidity Input Power -40 °C to +85°C 10% to 90% 5VDC Operating Voltage Antenna Connector Supply Range: VCC Maximum: 5.5 Minimum: GND Maximum: VCC Surface mount UFL SIM Holder Standard 3V SIM holder IP Protocols Supported MTSMC-G2 DNS Resolve, FTP client, LCP, PPP (dial-out),TCP socket, UDP socket, PAP & CHAP authentication MTSMC-G2-IP DNS Client, FTP Client, ICMP (Ping), POP3 Client, SMTP Client, TCP Client & Server, UDP Client & Server, IP, PPP (dial-out) with PAP & CHAP authentication MTSMC-G2-IP Automatic connect/reconnect, device monitor, modem emulation, Ping & TCP keep alive, wake-up on caller ID, wake-up on ring EMC Compliance FCC Part 15 EN55022 EN55024 Radio Compliance FCC Part 22 FCC Part 24 RSS 132 RSS 133 EN 301 511 EN 301 489-1 EN 301 489-7 AS/ACIF S042.1 AS/ACIF S042.3 Safety Compliance UL 60950-1 cUL 60950-1 IEC 60950-1 AS/NZS 60950-1 Network Compliance PTCRB Two years Voltage at Any Signal Pin M2M Applications Compliance Warranty Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Comment [DAR29]: From Dustin 6/24/09 Comment [DAR30]: From Dustin 6/24/09 Comment [DAR31]: Updated list from Dustin for Rev. K 57 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Specifications Continued: Category Features Description Modes of Operation: Data Mode, Command Mode, and Voice Mode Embedded TCP/IP stack Short Message Services (SMS) RTS/CTS hardware flow control AT command compatible Support for HR, FR, EFR, and AMR (Adaptive Multi Rate) voice codec support Flash upgradeable Non-volatile memory DC Electrical Characteristics Units: Volts 5V DC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Parameter Digital Signal Input Low Level –DTR (40), –TXD (35), –RTS (33) Digital Signal Input High Level –DTR (40), –TXD (35), –RTS (33) Digital Signal Output Low Level –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Digital Signal Output High Level –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Reset (Low Active) Input Low Level –Reset (24) Reset (Low Active) Input High Level –Reset (24) Digital Input Capacitance Minimum Maximum GND 0.8 Vcc 0.4 3.84 0.8 14pF Power Measurements Comment [DAR32]: Measurements for MTSMC-G2-IP 73120965 Rev 0 from Tom Fix. He suggested the current peak text also 4/22/09. He said these measurements apply to G2 without IP, too. MTSMC-G2 Measured Power* Measures at Input Voltage 5.00 Sleep Typical Maximum Peak Current (AMPS) 0.049 0.113 0.24 1.10 Watts 0.245 0.564 1.195 Comment [DAR33]: Measurements for MTSMC-G2-IP 73120965 Rev 0 from Tom Fix. He suggested the current peak text also 4/22/09. He said these measurements apply to G2 without IP, too. MTSMC-G2-IP Measured Power* Measures at Input Voltage 5.00 Sleep Typical Maximum Peak Current (AMPS) 0.080 0.135 0.280 1.250 Watts 0.382 0.664 1.358 Note: Current Peak = 1500mA maximum during Tx burst. Comment [DAR34]: Measurements for MTSMC-G2-gp from Tom Fix 10/06/09. MTSMC-G2-GP (for GPS) Measured Power* Measures at Input Voltage 5.00 Sleep Mode Typical Maximum Peak Current (AMPS) 0.013 0.115 0.481 1.400 Watts 0.065 0.574 2.386 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 58 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell * Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 59 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Comment [DAR35]: Vault Data 357 08/26/09 Mechanical Drawings – Basic Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 60 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Comment [DAR36]: Vault Data 375 08/26/09 Mechanical Drawings – Voice Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 61 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Comment [DAR37]: 8/26/09. Dean's #357 in Vault Data MTSMCG2-IP-Manual.png Mechanical Drawings – IP Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 62 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Comment [DAR38]: 8/26/09. Dean's #357 in Vault Data MTSMCG2-GP-Manual.png Mechanical Drawings – GPS Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 63 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Application Notes Flashing LED Interface The flashing LED signal is used to indicate the working mode of the SocketModem. LEDs and SocketModem Status Signal SocketModem Status OFF Download mode or switched OFF> ON Continuously lit Switched ON (not registered on the network) Flashing Switched ON (registered on the network) RF Performances RF performances are compliant with the ETSI recommendation 05.05 and 11.10. Note: The following statistics are subject to change due to pending test results. The main parameters are: Receiver Features • EGSM Sensitivity : < -104 dBm • GSM 1800/GSM 1900 Sensitivity : < -102 dBm • Selectivity @ 200 kHz : > +9 dBc • Selectivity @ 400 kHz : > +41 dBc • Dynamic range : 62 dB • Intermodulation : > -43 dBm • Co-channel rejection : + 9 dBc Comment [DAR39]: Tom Hofstedt expects text results in by June 24th. Transmitter Features • Maximum output power (EGSM) : 33 dBm ± 2 dB • Maximum output power (DCS/PCS) : 30 dBm ± 2 dB • Minimum output power (EGSM): 5 dBm ± 5 dB • Minimum output power (DCS/PCS): 0 dBm ± 5 dB • H2 level : < -30 dBm • H3 level : < -30 dBm • Noise in 925 - 935 MHz : < -67 dBm • Noise in 935 - 960 MHz : < -79 dBm • Noise in 1805 - 1880 MHz : < -71 dBm • Phase error at peak power : < 5 ° RMS • Frequency error : ± 0.1 ppm max RF Connection and Antenna The RF connector on the SocketModem GPRS is a UFL standard type. See Chapter 1 for Antenna System details. Microphone Inputs The MIC inputs are differential ones. They already include the convenient biasing for an electret microphone (0.5 mA and 2 Volts). This electret microphone can be directly connected on these inputs. The impedance of the microphone has to be around 2K. These inputs are the standard ones for a handset design. The gain of the MIC inputs is internally adjusted. The gain can be tuned from 30dB to 51dB. The connection to the microphone is direct. MIC2P C1 = 22pF to 100 pF 33 pF recommended C1 MIC2N Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 64 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Changing the Quad Band The SocketModem Cell and the SocketModem iCell both support quad band frequencies (850/1900/900/1800 MHz). In reality, these products operate like dual, dual-band devices. In other words, they can be configured for 850/1900 or 900/1800 MHz. They do not auto-seek the local area frequency. Build Options These wireless modems can be ordered with the default set to 850/1900 MHz or 900/1800 MHz. • 850/1900 MHz – The wireless modem defaulting to 850/1900 MHz is the default build option. • 900/1800 MHz – The wireless modem defaulting to 900/1800 MHz is identified with -ED in the product ordering number which signifies European default. Changing the GSM Band If for any reason, such as moving the modem from one geographical area to another, you want to change the band, you can accomplish this by using the +WMBS AT Command. Steps for Changing the GSM Band Use a terminal application such as HyperTerminal for entering the AT Command. 1. To open HyperTerminal, click Start. Then select Programs > Accessories > Communications. Then click HyperTerminal. 2. When the command window opens, type AT+WMBS=. Press Enter. • For , enter the option you desire: 4 = Dual-band mode 850/1900MHz 5 = Dual-band mode 900/1800MHz • For , enter the option you desire: 0 = Modem must be reset in order to use the specified band(s). This is the default. 1 = Modem restarts immediately using the specified band(s). Example: AT+WMBS=4,0. Press Enter. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 65 PART 2 – Embedded Wireless Modems Chapter 2 – SocketModem Cell and iCell Global Positioning System (GPS) Technical Specifications Receiver Type L1 Frequency GPS C/A code SBAS Capable 51 Channel Acquisitions 14 Channel Tracking Accuracy Position 2.5m CEP Velocity 0.1m/sec Timing 300ns Open Sky TTFF Hot start 1 second Cold start 29 seconds average Reacquisition < 1s Sensitivity Tracking 161dBm Update Rate 1Hz standard Dynamics 4G Operational Limits Altitude < 18,000m or Velocity < 515m/s Datum Default WGS-84 Interface UART Protocol NMEA-0183 V3.01, GGA, GLL, GSA, GSV, RMC, VTG Features • Tests 8 million time-frequency hypothesis per sec • Open sky cold start – 29 second • Signal detection better than -161dBm • Reacquisition sensitivity – 155dBm • Accuracy 2.5m CEP • Multipath detection and suppression • Supports active or passive antenna Underwriters Laboratories Required Global Positioning System (GPS) Statement Note the following information required by Underwriters Laboratories: Underwriters Laboratories, Inc. (“UL”) has not tested the performance or reliability of the Global Positioning System (“GPS”) hardware, operating software or other aspects of this product. UL has only tested for fire, shock or casualties as outlined in UL’s Standard(s) for Safety.UL60950-1 Certification does not cover the performance or reliability of the GPS hardware and GPS operating software. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY GPS RELATED FUNCTIONS OF THIS PRODUCT. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 66 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA Chapter 3 – SocketModem® CDMA (MTSMCC1) Introduction The Multi-Tech SocketModem CDMA is a complete, ready-to-integrate, embedded wireless modem. Designed for global use, it offers standards-based multi-band CDMA200 1x performance. The SocketModem CDMA is based on industry-standard open interfaces and utilizes Multi-Tech’s universal socket design. Notes about Activation: • • These units are shipped without network activation. To connect to the wireless network, you will have to establish a wireless account. See the Wireless Activation procedures in a separate document included with your Developer Kit and available on the Developer Kit CD. Product Build Options and Ordering Information Product Description MTSMC-C1-N1 MTSMC-C1-N2 MTSMC-C1-N3 MTSMC-C1-N4 MTSMC-C1-N9 MTSMC-C1-N11 MTSMC-C1-N12 MTSMC-C1-N14 MTSMC-C1-N15 MTSMC-C1-N16 SocketModem 800/1900 MHz CDMA 1xRTT – Generic Random A-Key SocketModem 800/1900 MHz CDMA 1xRTT – Sprint (USA) SocketModem 800/1900 MHz CDMA 1xRTT – Verizon (USA) SocketModem 800 MHz CDMA 1xRTT with R–UIM SocketModem 800/1900 MHz CDMA 1xRTT – Generic Zero A-Key SocketModem 800/1900 MHz CDMA 1xRTT with R-UIM SocketModem 800/1900 MHz CDMA 1xRTT – Bell Mobility Canada SocketModem 800/1900 MHz CDMA 1xRTT – Alltel (USA) SocketModem 800/1900 MHz CDMA 1xRTT - Telus SocketModem 800/1900 MHz CDMA 1xRTT - Aeris Developer Kit Universal Developer Kit MTSMI-UDK Region Order this Product Regional US US Regional Regional Regional Canada US Canada US Global How to Read the Product Codes in the Table Above: C1 CDMA N1 Generic Random A-Key. Requires provisioning. Must be programmed with Provisioning Information (PRI) and a Preferred Roaming List (PRL). N2 Sprint USA N3 Verizon USA N4 800 MHz with R-UIM N9 Generic Zero A-Key. Requires provisioning. Must be programmed with Provisioning Information (PRI) and a Preferred Roaming List (PRL). N11 800/1900 MHz with R-UIM N12 Bell Mobility Canada N14 Alltel USA N15 Telus Canada N16 Aeris US UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MTSMC-C1-N3.Rx. “R” indicates product revision. “x” is the revision number. AT Commands Reference Guides Products SocketModem CDMA (MTSMC-C1) AT Commands Reference Guide Title and Document Product Number CDMA AT Commands Reference Guide (S000294x) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Fax Commands Voice Commands NA included in S000294x 67 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA Technical Specifications The SocketModem CDMA (MTSMC-C1) meets the following specifications: Category Description Standard CDMA2000 1xRTT Frequency Bands Dual-band 800/1900 MHz CDMA Serial/Data Speed Serial interface supporting DTE speeds to 230K Packet data up to 153.6K bps forward and reverse channels Circuit-switched data up to 14.4K bps Data Format Asynchronous, transparent and non-transparent Weight 1.2 oz. (34 g) Operating Temperature -30° to +70° C Storage Temperature -40° to +85° C Humidity 20% to 90% (non-condensing) Operating Voltage 5VDC Power Measurements 5V: Typical: 400mA; Maximum: 700mA Connectors Antenna: MMCX R-UIM: Standard 3V R-UIM receptacle (For China only, 5V R-UIM) Certifications & Approvals Safety Certifications UL 60950 cUL 60950 EN 60950 AS/NZS 60950:2000 EMC Approvals FCC Part 2, 15, 22, 24 EN 55022 Network CDG 1 & 2 Warranty 2 years Features Short Message Services (SMS): Mobile originated; Mobile terminated Cell broadcast Over the Air Activation (OTA) OTASP; OTAPA SMS Features: Text & PDU, Point-to-Point, cell broadcast TCP/IP stack AT command compatible Management Features: Phone book management Fixed dialing number Real time clock Alarm management Supports AMR (Adaptive Multi Rate) voice coder Supports Cellular Text Telephone Modem Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 68 PART 2 – Embedded Wireless Modems Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Chapter 3 – SocketModem CDMA 69 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA Comment [DAR40]: Vault Data #315 8/26//09 Mechanical Drawings – Basic Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 70 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA DC Electrical Characteristics 5VDC Characteristics (VDD = 5V ± 0.2V) VDDMAX Digital Inputs –DTR (40), –TXD (35), –RTS (33) –RESET Digital Outputs –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Digital Input Capacitance = 5.25V Input High Min 2.0V Input High Min 2.0V Output High Min 4V Input Low Max 0.8V Input Low Max 0.5V Output Low Max 0.4V Current Drive: 2mA 5 pF Power Measurements* Operating Mode Band Average (mA) CDMA RXTX Full Power CMA RXTX Average Power CDMA Standby Cellular PCS Cellular PCS Cellular PCS 615 770 340 445 20 20 * Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 71 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA Application Notes Flashing LED Interface The flashing LED signal is used to indicate the working mode of the SocketModem. LED and SocketModem Status Signal OFF ON SocketModem Status Download mode or switched OFF> Continuously lit Switched ON (not registered on the network) Flashing Switched ON (registered on the network) RF Interface Radio Characteristics Frequency RX Frequency TX Impedance VSWR Typical Radiated Gain Output Power CDMA 800 869 to 894 MHz 824 to 849 MHz CDMA 1900 1930 to 1990 MHz 1850 to 1910 MHz 50 ohms <2 0 dBi in at least one direction .63W in AMPS .35W in CDMA RF Connection and Antenna The RF connector on the SocketModem is an MMCX standard type. See Chapter 1 for Antenna System details. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 72 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA Provisioning a Generic SocketModem CDMA The Difference between a Pre-Provisioned SocketModem CDMA and a Generic SocketModem CDMA Pre-Provisioned SocketModem CDMA Multi-Tech offers several pre-provisioned SocketModem CDMA units (see the Product Ordering Information table at the beginning of this chapter). Pre-provisioned SocketModem CDMA builds are pre-programmed to operate only on a designated CDMA carrier’s network; for example, the MTSMC-C1-N2 is pre-programmed (provisioned) for use on the Sprint network in the USA. Generic SocketModem CDMA Multi-Tech also offers two generic SocketModem CDMA models, the MTSMC-C1-N1 (Random A-Key) and MTSMC-C1-N9 (Zero A-Key). These generic SocketModems are not pre-programmed to operate on any designated CDMA carrier’s network. Overview of the Provisioning Process Requirements • A generic SocketModem CDMA-C1-N1 or -N9. • AT Commands Reference Guide for the SocketModem CDMA. • A developer software tool called WPST. Procedures Step 1. Get the PRI and PRL from your wireless carrier. Step 2. Set the provisioning commands, which are described in the AT Commands Reference Guide for the SocketModem CDMA, Chapter 16, using the provisioning information provided by the CDMA wireless network carrier. Step 3. Using the WPST tool, download the carrier’s specific PRI (Provisioning Information) and PRL (Preferred Roaming List) into the SocketModem CDMA. The wireless modem is now provisioned and can be activated on your wireless carrier’s network, according to the carrier’s activation instructions. See the Activation directions that accompany Multi-Tech wireless modems. Provisioning Terminology A-Key The A-Key is a 64-bit cryptographic key variable stored in the semi-permanent memory of the mobile station and also known to the Authentication Center of the wireless carrier's system. The generation of the A-Key is the responsibility of the wireless service provider. It is established and entered when the mobile station is first put into service. The CDMA network carrier you choose for you SocketModem CDMA product will let you know whether it uses the Random A-Key or the Zero A-Key in its authentication process. That will determine whether you purchase the -N1 or the –N9 build. Provisioning Provisioning is the programming of a SocketModem CDMA wireless modem to set the PRI and PRL provided by wireless network carrier that you are have chosen as your CDMA wireless network carrier. After the modem is provisioned, it can then be activated on the wireless network for which it is provisioned. MultiTech provides two SocketModems CDMA builds that are not pre-provisioned: MTSMC-C1-N1 and MTCABC1-N9. PRI stands for Provisioning Information. Provisioning Information is your wireless network carrier’s profile of parameter settings that must be programmed into your wireless modem in order for it to operate on the carrier’s wireless network. PRL stands for Preferred Roaming List. The PRL is a list of the wireless network service provider’s preferred roaming partners. This list is downloaded from your network service provider during the provisioning process. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 73 PART 2 – Embedded Wireless Modems Chapter 3 – SocketModem CDMA CDMA Terminology and Acronyms This is an alphabetical list of the CDMA cellular industry’s terminology and acronyms. Second Generation. This is an all digital cellular systems developed to replace the first analog cellular systems. (GSM and CDMA). 3G Third Generation. This is the next generation digital cellular systems designed to have high-speed data access and higher voice capacity (CDMA & CDMA2000). CBM Cell Broadcast Message. This is an SMS message that is broadcast to all mobiles on the network. CDMA CDMA (Code Division Multiple Access). CDMA is a spread spectrum, digital wireless modulation scheme for cellular communications systems. It has approximately 3 times the voice capacity of GSM networks. See IS-95, IS-95B, IS-2000. cdmaONE cdmaOne is a brand name, trademarked and reserved for the exclusive use of the CDMA Development Group (see their Web site at cdg.org). cdmaOne describes a complete wireless system that incorporates the IS-95 CDMA air interface, the ANSI-41 network standard for switch interconnection and many other standards that make up a complete wireless system. cdma2000 cdma2000 is a third generation (3G) wireless system. It contains a significant increase in voice capacity and high-speed data rates. It is backward compatible with IS-95B and IS-95A. cdma2000 1xRTT "1xRTT" stands for 1 times Radio Transmission Technology and is used to identify the version of CDMA2000 radio technology that operates in a pair of 1.25-MHz radio channels (one times 1.25 MHz, as opposed to three times 1.25 MHz in 3xRTT). Although theoretically capable of higher data rates, most carrier implementations have limited the peak data rate to 144 kbit/s. While 1xRTT officially qualifies as 3G technology, 1xRTT is considered by some to be a 2.5G. ESN "ESN" stands for Electronic Serial Number. It is a 32-bit binary number that identifies each cellular phone. Handset (Path) Handset (Path). This is the audio path (microphone & speaker) that connects to a traditional hand held telephone receiver, usually dual balanced electrical lines. Headset (Path) Headset (Path). This is the audio path (microphone & speaker) that connects to an earpiece with a microphone, usually single electrical lines. IMSI International Mobile Station IS. This is an international 15 digital phone number that uniquely identifies a mobile. IMSI=MCC + MNC + MIN. IOTA IOTA stands for Internet Over The Air. IS-95 IS-95 is the first CDMA standard published by Qualcomm in 1993. It is a TIA standard for North American cellular systems based on CDMA. It is widely deployed in North America and Asia. IS-95A IS-95A is a CDMA standard with improved voice quality. IS-95A defines what generally is known as cdmaOne, which supports voice and 14.4 Kbps data rates. This standard is widely used throughout the world. IS-95B IS-95B is a CDMA standard contains Medium Data Rate capabilities and bug fixes for system access failures. It is considered a 2.5G system. It supports data rates up to 115 Kbps. IS-2000 IS-2000 is the first 3G CDMA standard based on IS-95B. It contains a significant increase in voice capacity and high-speed data rates. It is backward compatible with IS-95B and IS-95A. IS-707 TIA/EIA/IS-707 describes data services available on wideband spread spectrum systems. It is organized into a series of related recommendations, some of which address functions common to all CDMA data services and others that describe a specific data service. MCC Mobile Country Code is a pre-defined 30-digital number that represents a country in the IMSI. MDN MDN stands for Mobile Data Number or the mobile phone number. MIN MIN stands for Mobile Identification Number or mobile user account number. MNC MNC stands for Mobile Network Code, a pre-defined 2-digital number that represents a subnetwork in the IMSI (usually set to “00”). MO MO stands for Mobile Originated, an action (usually a call) that is first started from the phone. An outgoing call or SMS. MS MS stands for Mobile Station. The term MS is commonly used to represent the phone or mobile. MT MT stands for Mobile Terminated. MT is an action, usually a call that is first started from a land based network. An incoming call or SMS. MSM MSM stands for Mobile Station Modem. NAM NAM stands for Number Assignment Modem. The NAM is collection of internal parameters that define a working phone for a given network (phone number, access parameters, etc.). NID NID stands for Network ID. The NID is an identification number that represents geographic location of a common coverage area; but is a subset of the SID, usually a neighborhood in a large city. NID is usually not used and is set to zero. Also see SID. NV-RAM NV-RAM stands for Non-Volatile Random Access Memory. NV-RAM is a data storage device that does not lose its data when power is turned off. 2G Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 74 PART 2 – Embedded Wireless Modems OTAPA OTASP P-REV PDU PN Offset PRI PRL PSTN RF RSSI R-UIM SID SIM SMS TA/TE Chapter 3 – SocketModem CDMA OTAPA stands for Over The Air Parameter Administration. It is an automatic update in internal software parameters (PRL for example) by means of a specially defined CDMA data call that is mobile terminated (MT). OTASP stands for Over The Air Service Programming. It is an automatic update in internal software parameters PRL; for example, PRL by means of a specially defined CDMA data call that is mobile terminated (MT). P-REV is the CDMA revision of the mobile or base station. PDU stands for Protocol Data Unit. It is a GSM SMS standard whereby any type of binary data can be transported via an SMS message. In the CDMA system, the PDU mode will not be supported; instead, the Unicode format message is supported. PN Offset stands for Pseudorandom Noise Offset. In a CDMA network the PN offset is a variable time delay offset of a repeating random noise generator that is used to distinguish individual sectors of a base station. PRI stands for Provisioning Information. Provisioning Information is your wireless network carrier’s profile of information that must be programmed into your wireless modem in order for it to operate on the carrier’s wireless network. PRL stands for Preferred Roaming List. The Roaming List is provided by the wireless network carrier during the process of provisioning your SocketModem. The PRL is a list of wireless service provider’s preferred roaming partners. PSTN stands for Public Switching Telephone Network. It is the traditional telephone network. RF stands for Radio Frequency. RSSI stands for Receive Signal Strength Indicator: This parameter represents the total RF received signal power from the base station(s) the mobile sees. R-UIM stands for Removable User Identity SocketModem. The R-UIM is similar to a SIM (Subscriber Identity SocketModem), but it is designed for networks other than GSM (Global System for Mobile Telecommunications); i.e., networks such as CDMA. The R-UIM card contains user information and data features on a removable smart card about the size of a postage stamp. It is a dual-mode solution that can store both GSM provisioning and CDMA provisioning on a single card. When used with a GSM handset, the R-UIM operates like a GSM SIM. SID stands for System ID. The SID is an identification number that represents geographic locations of a common coverage area, usually a large city. Also see NID. SIM stands for Subscriber Identity SocketModem. A SIM card is a portable memory chip. The SIM holds personal identity information, cell phone number, phone book, text messages and other data. SMS stands for Short Messaging Service. it is a supplementary service that is capable of sending and receiving short length text messages to/from the mobile. TA/TE stands for Terminal Application/Terminal Equipment. This is the end “device” (combination of hardware and software) that communicates with a modem via a serial link. In this context, it is the device (PDA/Computer) connected to the modem. Also see DTE. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 75 PART 2 – Embedded Wireless Modems Chapter 4 – SocketModem EDGE Chapter 4 – SocketModem® EDGE (MTSMCE1) Introduction The Multi-Tech SocketModem EDGE embedded wireless modem delivers some of the fastest cellular data speeds by utilizing EDGE technology. It allows users to connect to the Internet and send and receive data up to three times faster than possible with an ordinary GSM/GPRS network making it ideal for highly data-intensive applications. Based on industry-standard open interfaces, the SocketModem EDGE wireless modem is equipped with quad-band GSM, which means it can be used worldwide on all existing GSM networks. Product Build Options and Ordering Information Product Description Region MTSMC-E1 SocketModem Quad Band EDGE Class 12 – 5V Global MTSMC-E1-V SocketModem Quad Band EDGE Class 12 w/Voice – 5V Global MTSMI-UDK Universal Developer Kit Order This Product Global How to Read the Product Codes in the Table Above: E1 EDGE Voice UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MTSMC-E1.Rx “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product SocketModem EDGE (MTSMC-E and E1) Reference Guides Title and Document Product Number SocketModem EDGE AT Commands Reference Guide (S000371x) Fax Commands Voice Commands NA Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Included in S000371x 76 PART 2 – Embedded Wireless Modems Chapter 4 – SocketModem EDGE Technical Specifications The SocketModem EDGE (MTSMC- E1) wireless modem meets the following specifications: Category Description Standards Serial Speed EDGE: E-GPRS Class 12 GPRS: GPRS Class 12 Packet Data rates up to 240K bps (modulation & coding scheme, MCS 1-9, Mobile station Class B) Circuit-switched data up to 14.4 bps non-transparent mode, asynchronous Serial interface supporting DTE speeds to 460K bps Band Frequency Quad-band 850/900/1800/1900 MHz Connectors Antenna: MMCX SIM: Standard 1.8V or 3V SIM receptacle Data Speed IP Protocols Supported TCP, UDP, DNS, FTP, SMTP, POP3, HTTP Operating Voltage 5VDC Operating Temperature -30° to +70° C Storage Environment -40° to +85° C Humidity 20% to 90% non-condensing Physical Dimensions 2.541" L x 1.375" W 64.541mm L x 34.92 mm W For maximum component heights top and bottom, see the Mechanical Drawings on the next two pages. Weight 1 oz. (0.028 kg.) Compliance EMC Compliance FCC Part 2, 15, 22, 24 EN 55022 EN 55024 Radio Compliance FCC Part 22 FCC Part 24 RSS 132 RSS 133 EN 301 511 EN 301 489-1 EN 301 489-7 AS/ACIF S042.1 AS/ACIF S042.3 Safety Compliance UL 60950-1 cUL 60950-1 IEC 60950-1 AS/NZS 60950:2000 Network Compliance PTCRB Warranty 2 years Intelligent Features SMS – Text & PDU, Point-to-Point, cell broadcast AT Command Compatible Voice features include Half Rate (HR), Full Rate (FR), Enhanced Full Rate (EFR), Adaptive multi rate (AMR), as well as hands free echo cancellation, and noise reduction Embedded TCP/IP protocol stack brings Internet connectivity Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 77 PART 2 – Embedded Wireless Modems Chapter 4 – SocketModem EDGE Comment [DAR41]: Vault Data for E1 is #372 8/26/09 Mechanical Drawings – Basic Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 78 PART 2 – Embedded Wireless Modems Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Chapter 4 – SocketModem EDGE 79 PART 2 – Embedded Wireless Modems Chapter 4 – SocketModem EDGE Mechanical Drawings – Voice Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Comment [DAR42]: Vault Data for E1 Voice is #372 8/26/09 80 PART 2 – Embedded Wireless Modems Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Chapter 4 – SocketModem EDGE 81 PART 2 – Embedded Wireless Modems Chapter 4 – SocketModem EDGE Comment [DAR43]: New from Dustin 8/31/09 for E1 DC Electrical Characteristics Operating Conditions 5 Volts Parameter Supply Range - Vcc Minimum 4.75 Maximum 5.25 Absolute Maximum Rating Parameter Minimum Maximum Voltage at Any Signal Pin DC Electrical Characteristics Units (Volts) Parameter Digital Signal Input Low Level Minimum Maximum 0.8 Digital Signal Input High Level Digital Signal Output Low Level 0.33 Digital Signal Output High Level 3.84 Reset (Low Active) Input Low 1.14 Reset (Low Active) Input High 2.7 Digital Input Capacitance 10pF Power Measurements MTSMC-E1 and MTSMC-E1-V Measured Power* at Input Voltage 5.00 Sleep Typical Maximum Peak Current (AMPS) 0.010 0.128 0.675 1.500 Watts 0.050 0.64 3.2 Comment [DAR44]: These measurements apply to both the MTSMC-E1 and MTSMC-E1-V since the only difference is the voice pins.From Jerome 9/8/09 * Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 82 PART 2 – Embedded Wireless Modems Chapter 4 – SocketModem EDGE Application Notes RF Performances RF performances are compliant with the ETSI recommendation 05.05 and 11.10. The main parameters are: Receiver Features • • • • • • • EGSM Sensitivity : < -108 dBm GSM 1800/GSM 1900 Sensitivity : < -107 dBm Selectivity @ 200 kHz : > +9 dBc Selectivity @ 400 kHz : > +41 dBc Dynamic range : 62 dB Intermodulation : > -43 dBm Co-channel rejection : + 9 dBc Transmitter Features • • • • • • • • • • • Maximum output power (EGSM) : 24 dBm +/- 2 dB Maximum output power (DCS/PCS) : 30 dBm +/- 2 dB Minimum output power (EGSM): 5 dBm +/- 5 dB Minimum output power (DCS/PCS): 0 dBm +/- 5 dB H2 level : < -30 dBm H3 level : < -30 dBm Noise in 925 - 935 MHz : < -67 dBm Noise in 935 - 960 MHz : < -79 dBm Noise in 1805 - 1880 MHz : < -71 dBm Phase error at peak power : < 5 ° RMS Frequency error : +/- 0.1 ppm max RF Connection and Antenna The RF connector on the SocketModem is an MMCX standard type. See Chapter 1 for Antenna System details. Audio Interface – Electrical Characteristics Speaker Output Differential speaker output capable of driving 8 ohm load. 1.0945 Vpp (differential) typical. Microphone Input Balanced microphone input: full scale input 1.1 Vpp. Microphone Inputs The MIC inputs are differential ones. They already include the convenient biasing for an electret microphone (0,5 mA and 2 Volts). This electret microphone can be directly connected on these inputs. The impedance of the microphone has to be around 2K. These inputs are the standard ones for a handset design. The gain of the MIC inputs is internally adjusted. The gain can be tuned from 30dB to 51dB. The connection to the microphone is direct. MIC2P C1 = 22pF to 100 pF 33 pF recommended C1 MIC2N Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 83 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Chapter 5 – SocketModem® HSDPA (MTSMCH) Introduction The Multi-Tech SocketModem HSDPA embedded wireless modem delivers some of the fastest cellular data speeds by utilizing HSDPA technology. It allows users to connect to the Internet and send and receive data faster than possible with an ordinary GSM/GPRS network making it ideal for highly data-intensive applications. Based on industry-standard open interfaces, the SocketModem wireless modem is equipped with quad-band, high-speed RS232 technology, which means it can be used worldwide on all existing GSM networks. In addition, it utilizes Multi-Tech's universal socket design. Product Build Options and Ordering Information Product Description Region MTSMC-H MTSMC-H-U MTSMI-UDK SocketModem Tri Band HSPDA Serial Modem – 5V SocketModem Tri Band HSPDA USB Modem – 5V Universal Developer Kit Global Global Global Order This Product How to Read the Product Codes in the Table Above: HSDPA (High-Speed Downlink Packet Access) USB UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MTSMC-H.Rx. “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product Reference Guides Title and Document Product Number SocketModem HSDPA SocketModem HSDPA (MTSMC-H) AT Commands Reference Guide (S000453x) Fax Commands Voice Commands NA Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) NA 84 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Technical Specifications The SocketModem HSDPA (MTSMC- H) wireless modem meets the following specifications: Category General Frequency Bands GSM Class Output power (according to Release 99) Power Supply Physical Description HSDPA Features 3GPP Release 5 UMTS Features 3GPP Release 4 Description • UMTS/HSDPA: Triple band, 850/1900/2100MHz • GSM/GPRS/EDGE: Quad band, 850/900/1800/1900MHz Small MS Class 4 (+33dBm ±2dB) for EGSM850 Class 4 (+33dBm ±2dB) for EGSM900 Class 1 (+30dBm ±2dB) for GSM1800 Class 1 (+30dBm ±2dB) for GSM1900 Class E2 (+27dBm ± 3dB) for GSM 850 8-PSK Class E2 (+27dBm ± 3dB) for GSM 900 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1900 8-PSK Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI Class 3 (+24dBm +1/-3dB) for UMTS 1900,WCDMA FDD BdII Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdV 5VDC ± 10% 3.1" L x 1.4" W x 0.5" H; 1 oz. (7.8 cm x 3.5 cm x 1.2 cm; 28 g) 3.6 Mbps, UL 384 kbps UE CAT. [1-6], 11, 12 supported Compressed mode (CM) supported according to 3GPP TS25.212 PS data rate – 384 kbps DL / 384 kbps UL CS data rate – 64 kbps DL / 64 kbps UL GSM / GPRS / EGPRS Features Data Transfer GPRS • Multislot Class 10 • Full PBCCH support • Mobile Station Class B • Coding Scheme 1 – 4 EGPRS • EDGE E2 power class for 8 PSK • Downlink coding schemes – CS 1-4, MCS 1-9 • Uplink coding schemes – CS 1-4, MCS 1-9 • BEP reporting • SRB loopback and test mode B • 8-bit, 11-bit RACH • PBCCH support • 1 phase/2 phase access procedures • Link adaptation and IR • NACC, extended UL TBF • Mobile Station Class B CSD • V.110, RLP, non-transparent • 9.6 kbps SMS Point-to-point MT and MO Cell broadcast Text and PDU mode Software AT Commands Microsoft® Compatibility SIM Application Toolkit Firmware Update AT GSM 07.05 and 07.07, Siemens AT commands for RIL compatibility (NDIS/RIL) ® RIL / NDIS for Windows Mobile SAT Class C Firmware update from host application over USB and ASC0 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 85 PART 2 – Embedded Wireless Modems Category Interfaces USB Serial Modem Interface UICC Interface Connectors SocketModem Interface Operating Environment Operating Temperatures Storage Environment Humidity Chapter 5 – SocketModem HSDPA Description USB 2.0 full speed (12Mbit/s) CDC ACM compliant NDIS driver included (XP only) 8-wire modem interface with status and control lines, unbalanced, asynchronous. Supported chip cards: SIM / UICC 3V, 1.8V Antenna: MMCX SIM: Standard 3V SIM receptacle Socket pins Min -30 °C Typ +25 °C -40° to +85° C 20% to 90% non-condensing Max +60 °C Certifications, Approvals, Directives, Warranty Certifications: Certifications & Approvals CE Mark, R&TTE Safety Certifications: UL 60950-1 EN 60950-1 EMC Approvals: FCC Part 22, 24 EN 301 489-1 EN 301 489-7 RSS 132, 133 Network: PTCRB RoHS All hardware components fully compliant with EU RoHS Directive Warranty 2 years Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 86 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Comment [DAR45]: Vault Data #319 for basic build 8/26/09 Mechanical Drawings – Basic Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 87 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Comment [DAR46]: Vault Data #319 for USB 8/26/09 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 88 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Mechanical Drawings – USB Build Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 89 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA DC Electrical Characteristics I/O DC Characteristics 5VDC Characteristics (VDD = 5V ± 0.25V) Digital Inputs –DTR (40), –TXD (35), –RTS (33) –RESET VDDMAX = 5.25V Input High Min 2.0V Input High Min 2.6V Digital Outputs Output High –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Min 4V Digital Input Capacitance Input Low Max 0.8V Input Low Max 1.0V Output Low Max 0.4V Current Drive 2mA 5 pF Power Measurements* Data Mode Power Consumption GPRS Power Consumption in EGSM/GPRS 900 MHz and GSM/GRPS 850 MHz Voltage +5V +5V +5V +5V Conditions During TX bursts @ 2W Average Class 8 Average Class 10 Average idle mode INOM 1.8 A 375mA 540mA 40mA IMAX 2.9 A GPRS Power Consumption in GSM/GRPS 1800 MHz and GSM/GRPS 1900 MHz Voltage +5V +5V +5V +5V Conditions During TX bursts @ 1W Average Class 8 Average Class 10 Average idle mode INOM 1.5 A 325mA 430mA 40mA IMAX 2.1 A EGPRS Power Consumption in EGRPS 900 MHz and EGRPS 850 MHz Voltage +5V +5V +5V +5V Conditions During TX bursts @ 2W Average Class 8 Average Class 10 Average idle mode INOM 1.8 A 315mA 410mA 40mA IMAX 2.9 A EGPRS Power Consumption in EGRPS 1800 MHz and EGRPS 1900 MHz Voltage +5V +5V +5V +5V Conditions During TX bursts @ 2W Average Class 8 Average Class 10 Average idle mode INOM 1.8 A 290mA 355mA 40mA IMAX 2.9 A WCDMA Power Consumption Voltage Conditions INOM IMAX +5V UMTS Data transfer Band I @+10dBm 390mA +5V HSDPA Data transfer Band I @+10dBm 450mA +5V UMTS Data transfer Band I @+23dBm 750mA 820mA +5V HSDPA Data transfer Band I @+23dBm 775mA 850mA +5V UMTS Data transfer Band II @+10dBm 455mA +5V HSDPA Data transfer Band II @+10dBm 500mA +5V UMTS Data transfer Band II @+23dBm 810mA 930mA +5V HSDPA Data transfer Band II @+23dBm 850mA 930mA +5V UMTS Data transfer Band V @+10dBm 390mA +5V HSDPA Data transfer Band V @+10dBm 420mA +5V UMTS Data transfer Band V @+23dBm 620mA 790mA +5V HSDPA Data transfer Band V @+23dBm 640mA 820mA1 Under total mismatch conditions at antenna connector. * Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 90 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Application Notes RF Performances RF performances are compliant with the ETSI recommendation 05.05 and 11.10. The main parameters are: Receiver Features • • • • • • • EGSM Sensitivity: < -108 dBm GSM 1800/GSM 1900 Sensitivity: < -107 dBm Selectivity @ 200 kHz: > +9 dBc Selectivity @ 400 kHz: > +41 dBc Dynamic range: 62 dB Intermodulation: > -43 dBm Co-channel rejection: + 9 dBc Transmitter Features • • • • • • • • • • • Maximum output power (EGSM): 24 dBm +/- 2 dB Maximum output power (DCS/PCS): 30 dBm +/- 2 dB Minimum output power (EGSM): 5 dBm +/- 5 dB Minimum output power (DCS/PCS): 0 dBm +/- 5 dB H2 level: < -30 dBm H3 level: < -30 dBm Noise in 925 - 935 MHz: < -67 dBm Noise in 935 - 960 MHz: < -79 dBm Noise in 1805 - 1880 MHz: < -71 dBm Phase error at peak power: < 5 ° RMS Frequency error: +/- 0.1 ppm max RF Connection and Antenna The RF connector on the SocketModem is an MMCX standard type. See Chapter 1 for Antenna System details. Air Interface Air Interface GSM / UMTS Parameter HSDPA / UMTS Connectivity UMTS Frequency Range Uplink (UE to Node B) UMTS Frequency Range Downlink (Node B to UE) Receiver Input Sensitivity @ ARP RF Power@ ARP with 50Ohm Load GPRS Coding Schemes EGPRS GSM Class GSM Frequency range Uplink (MS to BTS) GSM Frequency range Downlink (BTS to MS) Conditions Band I, II, V UMTS 850 Band V UMTS 1900 Band II UMTS 2100 Band I UMTS 850 Band V UMTS 1900 Band II UMTS 2100 Band I UMTS 850 Band V UMTS 1900 Band II UMTS 2100 Band I UMTS 850 Band V UMTS 1900 Band II UMTS 2100 Band I Class 10, CS1 to CS4 Class 10, MCS1 to MCS9 Small MS GSM 850 E-GSM 900 GSM 1800 GSM 1900 GSM 850 E-GSM 900 GSM 1800 Min. Typ. 824 1850 1920 869 1930 2110 +21 +21 +21 824 880 1710 1850 869 925 1805 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Max. 849 1910 1980 894 1990 2170 -109 -107 -108 +23 +23 +23 Unit +25 +25 +25 MHz MHz MHz MHz MHz MHz dBm dBm dBm dBm dBm dBm 849 915 1785 1910 894 960 1880 MHz MHz MHz MHz MHz MHz MHz 91 PART 2 – Embedded Wireless Modems Static Receiver input Sensitivity @ ARP RF Power@ ARP with 50Ohm Load (GSM; 1 TX) RF Power@ ARP with 50Ohm Load (GPRS; 1 TX) RF Power@ ARP with 50Ohm Load (EGPRS; 1 TX) RF Power@ ARP with 50Ohm Load (GPRS; 2 TX) RF Power@ ARP with 50Ohm Load (EGPRS; 2 TX) GSM 1900 1930 GSM 850 E-GSM 900 GSM 1800 GSM 1900 GSM 850 E-GSM 900 GSM 1800 GSM 1900 GSM 850 E-GSM 900 GSM 1800 GSM 1900 GSM 850 E-GSM 900 GSM 1800 GSM 1900 GSM 850 E-GSM 900 GSM 1800 GSM 1900 GSM 850 E-GSM 900 GSM 1800 GSM 1900 -102 -102 -102 -102 31 31 28 28 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Chapter 5 – SocketModem HSDPA 1990 MHz -108 -108 -107 -107 32 32 29.25 29.25 32 32 29.25 29.25 27 27 26 26 30.50 30.50 27.75 27.75 25 25 24 24 35 35 32 32 dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm 92 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Configuring the HSDPA Modem on Linux SLAX 6 All recent distributions of Linux Kernel v2.6 or higher and CDC_ACM USB will work well with the HSPDA modem. Follow procedure outlined here using the HSDPA on Linux SLAX 6, an efficient live distribution you can install on a USB stick. See www.slax.org. 1. Set the HSDPA in modem mode so that it can be enumerated automatically: AT^SUSB="Startup","Mdm" AT^SMSO 2. Boot SLAX 3. Plug the USB cable into the PC 4. Enable enumeration in a terminal: modprobe usbserial vendor=0x0681 product=0x0047 5. Make sure that the modem was enumerated ls -la /dev/ttyUSB* The response should be: /dev/ttyUSB0 6. Launch KPPP& 7. Create a new account with AT&T: Dial *99***1# 8. Create a new modem HC25 Modem device: /dev/ttyUSB0 Flow control: None Line Termination: CR Connection Speed: 921600 9. Add modem commands to the initialization string; i.e., ATZ and AT+CGDCONT=1,"IP","isp.cingular" 10. Enter PAP authentication Login and enter password as usual Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 93 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Baud Rate Switches on the HSDPA SocketModem Note: For HSDPA serial model only. MTSMC-H SocketModem Baud Rate dip switch settings Switch Bank ● ● ● ● ● ● ● ● ● ● ● 920K ● 460K ● ● ● ● ● ● 230K 115K SocketModem Default ● ● ● ● ● 57.6K ● ● ● ● ● ● ● 38.4K ● 19.2K ● 9.6K Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 94 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Comment [DAR47]: SocketModem EDGE.gif Operating Modes The table below briefly summarizes the various operating modes. Mode Function Normal operation GSM / GPRS / UMTS / HSDPA SLEEP (for USB only) GSM IDLE GSM TALK GPRS IDLE GPRS DATA EGPRS DATA UMTS / HSDPA IDLE Power saving mode set automatically when no call is in progress and the USB connection is suspended by host or not present. Software is active. Once registered to the GSM network, paging with BTS is carried out in order to achieve synchrony with the GSM network. The repetition rate depends on the parameter BSPA_Multiframe. The SocketModem is ready to send and receive. Connection between two subscribers is in progress. Power consumption depends on the GSM network coverage and several connection settings (e.g. DTX off/on, FR/EFR/HR, hopping sequences and antenna connection). The following applies when power is to be measured in TALK_GSM mode: DTX off, FR and no frequency hopping, otherwise same as for IDLE measurements. The SocketModem is attached and ready for GPRS data transfer, but no data is currently sent or received. GPRS data transfer in progress. Power consumption depends on network settings (e.g. power control level), uplink / downlink data rates and GPRS configuration (e.g., used multislot settings). EGPRS data transfer in progress. Power consumption depends on network settings (e.g. power control level), uplink / downlink data rates and EGPRS configuration (e.g., used multislot settings). The SocketModem is attached and ready for UMTS / HSDPA data transfer, but no data is currently sent or received. UMTS DATA UMTS data transfer in progress. Power consumption depends on network settings (e.g., TPC Pattern) and data transfer rate. HSDPA DATA HSDPA data transfer in progress. Power consumption depends on network settings (e.g., TPC Pattern) and data transfer rate. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 95 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Turn off the SocketModem Using AT Command The best and safest approach to powering down is to issue the AT^SMSO command. This procedure lets the SocketModem log off from the network and allows the software to enter into a secure state and safe data before disconnecting the power supply. The mode is referred to as Power-down mode. In this mode, only the RTC stays active. After sending AT^SMSO do not enter any other AT commands. There is one way to verify that the SocketModem turns off: Wait for the ”OK” – response. It indicates that data has been stored non-volatile and that the SocketModem turns after about one second. Important Note: The SocketModem requires a reset to become active again. Automatic Shutdown Automatic shutdown takes effect if: • The modem exceeds the critical limits of overtemperature or undertemperature. The board temperature is constantly monitored by an internal NTC resistor. The values detected by the NTC resistor are measured directly on the board and are therefore not fully identical with the ambient temperature. Each time the board temperature goes out of range or back to normal, the modem instantly displays an alert (if enabled). URCs indicating the level "1" or "-1" allow the user to take appropriate precautions, such as protecting the SocketModem from exposure to extreme conditions. The presentation of the URCs depends on the settings selected with the AT^SCTM write command: AT^SCTM=1: Presentation of URCs is always enabled. AT^SCTM=0 (default): Presentation of URCs is enabled for 15 seconds time after startup. After 15 seconds operation, the presentation will be disabled, i.e. no alert messages can be generated. URCs indicating the level "2" or "-2" are instantly followed by an orderly shutdown, except in cases of temperature control during an emergency call (see paragraph below). The presentation of these URCs is always enabled; i.e., they will be output even though the factory setting AT^SCTM=0 was never changed. Temperature-Dependent Alerts Sending temperature alert (15s after start-up; otherwise, only if URC presentation enabled) ^SCTM_B: 1 Caution: SocketModem close to over-temperature limit. ^SCTM_B: -1 Caution: SocketModem close to under-temperature limit. ^SCTM_B: 0 SocketModem back to uncritical temperature range. Automatic shutdown (URC appears no matter whether or not presentation was enabled) ^SCTM_B: 2 Alert: SocketModem is above over-temperature limit and switches off. ^SCTM_B: -2 Alert: SocketModem is below under-temperature limit and switches off. Notes: • The MTSMC-H will not transmit temperature URC alerts. • The URCs will not display in data mode. Temperature Control during an Emergency Call If the temperature limit is exceeded while an emergency call is in progress the engine continues to measure the temperature, but deactivates the shutdown functionality. If the temperature is still out of range when the call ends, the SocketModem switches off immediately (without another alert message). Power Saving The modem is able to reduce its functionality to a minimum (during the so-called SLEEP mode) in order to minimize its current consumption. The following sections explain the SocketModem’s network dependant power saving behavior. The implementation of the USB host interface also influences the SocketModem’s power saving behavior and therefore its current consumption. During normal WCDMA operation; i.e., the modem is connected to a WCDMA network, the duration of a power-saving period varies. It may be calculated using the following formula: t = 2DRX value * 10 ms (WCDMA frame duration). Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 96 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Power Saving While Attached to GSM Networks The power saving possibilities while attached to a GSM network depend on the paging timing cycle of the base station. The duration of a power saving interval can be calculated using the following formula: t = 4.615 ms (TDMA frame duration) * 51 (number of frames) * DRX value. DRX (Discontinuous Reception) is a value from 2 to 9, resulting in paging intervals between 0.47 and 2.12 seconds. The DRX value of the base station is assigned by the GSM network operator. In the pauses between listening to paging messages, the SocketModem resumes power saving, as shown in the figure below. Power Saving and Paging in GSM Networks The varying pauses explain the different potential for power saving. The longer the pause the less power is consumed. Generally, power saving depends on the SocketModem’s application scenario and may differ from the above mentioned normal operation. The power saving interval may be shorter than 0.47 seconds or longer than 2.12 seconds. Power Saving While Attached to WCDMA Networks The power saving possibilities while attached to a WCDMA network depend on the paging timing cycle of the base station. During normal WCDMA operation, i.e., the SocketModem is connected to a WCDMA network, the duration of a power saving period varies. It may be calculated using the following formula: t = 2DRX value * 10 ms (WCDMA frame duration). DRX (Discontinuous Reception) in WCDMA networks is a value between 6 and 9, thus resulting in power saving intervals between 0.64 and 5.12 seconds. The DRX value of the base station is assigned by the WCDMA network operator. In the pauses between listening to paging messages, the SocketModem resumes power saving, as shown in the figure below. Power Saving and Paging in WCDMA Networks The varying pauses explain the different potential for power saving. The longer the pause the less power is consumed. Generally, power saving depends on the SocketModem’s application scenario and may differ from the above mentioned normal operation. The power saving interval may be shorter than 0.64 seconds or longer than 5.12 seconds. Power Saving During Network Search, GSM/WCDMA The power saving interval during network search depends on the network registration mode configured for the modem. This mode can be specified with the AT^SCFG command parameter MEopMode/RM: • In "Fast" mode, the power saving interval may last for up to 5 seconds. • In "Normal" mode, the power saving interval may last for up to 40 seconds. For details on how to configure the AT^SCFG parameter MEopMode/RM see the HSDPA AT Command Guide. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 97 PART 2 – Embedded Wireless Modems Chapter 5 – SocketModem HSDPA Interface Signal Descriptions USB Interface The SocketModem supports a USB 2.0 Full Speed (12Mbit/s) device interface. A USB host has to support at least 6 ‘Message Pipes” to work with the HSPDA USB interface. The USB I/O-pins are capable of driving the signal at min 3.0V. They are 5V I/O compliant. The USB interface is powered by VUSB. VUSB must be supplied by USB host in the range 4.5 to 5.25V. The maximum load in VUSB is 10mA. While the USB connection is active, the SocketModem will not change into SLEEP Mode. To enable switching into SLEEP mode the USB host must bring its USB interface into Suspend state. On incoming calls, the SocketModem will then generate a remote wake up request to resume the USB connection. Note: The MTSMC-H will not transition to sleep mode. USB Interface Signal Descriptions Signal Name I/O Signal Form and Level Commend VUSB If lines are unused, keep pins open. USB_DP USB_DN I/O I/O VINmin = 4.5V VINmax = 5.25V Active current: IItyp = 2.5mA IImax = 10mA Suspend current: IItyp = 900μA Input sensitivity (Diff), |D+ - D-|, VIN = 0.8V to 2.5V: 0.2V min Common mode range (Diff), VIN = 0.8V to 2.5V Receiver threshold (single-end), Vthresholdmin = 0.8V Vthresholdmax = 2.0V Receiver hysteresis, Vhystyp = 200mV If lines are unused, keep pins open. Note: For more information about the USB interface, see the separate USB Reference Guide available on the Universal Guide CD. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 98 PART 3 – Analog SocketModems Part 3 Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Chapter 7 – SocketModem (MT5692SMI) Chapter 8 – SocketModem (MT2492SMI) Chapter 9 – SocketModem (MT2456SMI-22) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 99 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Chapter 6 – SocketModem® (MT9234SMI) Introduction Multi-Tech’s SocketModem creates communication-ready devices by integrating data/fax/voice functionality into a single product design. The SocketModem is a space-efficient (1" × 2.5"), embedded modem that provides V.92/56K communication. The complete, ready-to-integrate modem dramatically reduces development time and costs for system designers. The MT9234SMI SocketModems are used for integrating data and fax communications. They are single-port modems that integrate the controller, DSP, and DAA in a 1" x 2.5" form factor and communicate to a host controller via an asynchronous serial interface. Product Build Options and Ordering Information Product Description MT9234SMI-92 MT9234SMI-L-92 MT9234SMI-P-92 MT9234SMI-P-L-92 MT9234SMI-HV-92 MT9234SMI-P-HV-92 MT9234SMI-LS MTSMI-UDK MTSMI-P-UDK MT9234SMI V.92 Serial Data, V.34 Fax, 5V V.92 Serial Data, V.34 Fax, 3.3V V.92 Parallel Data, V.34 Fax, 5V V.92 Parallel Data, V.34 Fax, 3.3V V.92 Serial Data, V.34 Fax, High Voltage, 5V V.92 Parallel Data, V.34 Fax, High Voltage, 5V Telecom Label MT9234SMI – Global Regulatory Label Developer Kits Universal Developer Kit SocketModem Parallel Developer Kit Region Order this Product Global Global Global Global Global Global Global Global Global How to Read the Product Codes in the Table Above: 92 V.92/56K data rate HV High Voltage 2KV Dielectric Isolation (EN60601) 3.3V Parallel interface LS Telecom Label UDK Universal Developer Kit Comment [DAR48]: Removed ITP (Industrial Temperature) because Rick said all 9234SMI are ITP. Other Product Codes: The complete product code may end in .Rx. For example, MT9234SMI-92.Rx. “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product SocketModem (MT9234SMI) Reference Guides Title and Document Fax Commands Product Number MT9234SMI AT Commands Reference See separate Fax Guides: Guide (S000434x) Class 1: S000262x Class 2 S000239x Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Voice Commands Included in S000434x 100 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Technical Specifications The SocketModem (MT9234SMI) meets the following specifications: Category Description Data Standards Data Format Character Format Serial/Data Speeds V.92, V.34 enhanced, V.34, V.32bis, V.32, V.22bis, V.22; Bell 212A and Bell 103 Serial, or 8-bit parallel interface, asynchronous 10 bit or 11 bit Serial port data rates adjustable to 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, and 230400 bps Client-to-Client Data Rates 33600, 31200, 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000, 9600, 7200, 4800, 2400, 1200, 0-300 bps Data Error Correction (ECM) Data Compression Fax Compatibility Fax Class Fax Compression V.44; V.42 (LAPM, MNP 2-4) V.42bis, MNP 5 V.17, V.29/V.27/V.21, V.34 Class 1 &1.0 – All builds Class 2, 2.0/2.1 – All builds MH, MR, MMR Fax Error Correction Mode ECM Modes of Operation Fax online modes; full duplex over dial-up lines; data mode; command mode; online command mode; V.54 test mode Weight Operating Temperature Storage Temperature Humidity Operating Voltage Power Measurements 0.6 oz. (0.017 kg.) -40° to +85° C -40° to +85° C 20% to 90% (non-condensing) 3.3V and 5V MT9234SMI 3.3V Typical: 122mA (0.40W @ 3.3VDC) Maximum: 136mA (0.49W @ 3.6VDC) Sleep Mode: 90mA to 95mA (.297W to .3135W @ 3.3VDC) 5V Typical: 125mA (0.62W @ 5VDC) Maximum: 138mA (0.72W @ 5.25VDC) Sleep Mode: 92mA (0.44W @ 5VDC) Note: Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. - 11 dBm (varies by country setting) - 43 dBm under worst-case conditions MT9234SMI 1.5Kv r.m.s. or 2121 VDC at working voltage of 250VAC MT9234SMI 2Kv r.m.s. or 2828VDC at working voltage of 125VAC XON/XOFF (software), RTS/CTS (hardware) 60 characters TAM: S-101 AT+V commands (no CODEC for speakers/microphone interface) Safety Certifications UL 60950 cUL 60950 EN 60950 AS/NZS 60950:2000 CCC Safety Certifications for HV Builds UL 60601-1 EN 60601-1 EMC Approvals FCC Part 15 Canadian EMC EN 55022 EN 55024 GB4943, GB9254 2 years Transmit Level Receiver Sensitivity DAA Isolation Flow Control Command Buffer Telephony / TAM Certifications & Approvals Warranty Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Comment [DAR49]: This came from email string involving Curt, Brandon Dalida, Jerome, dated 2/5/09 forwarded by Jerry to me. It covers sleep mode for the 5634SMIITP too. 101 PART 3 – Embedded Analog SocketModems Category Intelligent Features Chapter 6 – SocketModem (MT9234SMI) Description Fully AT command compatible Leased-line operation Sleep mode Autodial, redial Pulse or tone dial Dial pauses Auto answer Adaptive line probing Automatic symbol and carrier frequency during start-up, retrain, and rate renegotiations DTMF detection Callback security Distinctive ring Voice record and playback Call status display, auto-parity and data rate selections Keyboard-controlled modem options On-screen displays for modem option parameters Remote configuration DTR dialing Phone number storage Flash memory for firmware updates NVRAM storage for user-defined parameters Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 102 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) SocketModem Pin Out Serial Pin Out The MT9234SMI SocketModem uses a 20-pin interface to provide an on-board DAA with tip and ring connections, audio circuit for call-progress monitoring, LED driver for call status annunciation, and serial interface. Note: The bolded, shaded pins are the active MT9234SMI pins. Top View Serial SocketModem Pin Out Comment [DAR50]: Pinout 9234.png filed under rev K graphics For pin descriptions, see the Universal Pin Out Descriptions in Chapter 1. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 103 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Parallel Pin Out The parallel configuration is not compatible with the serial universal socket. The Parallel SocketModem uses a 22-pin interface to provide an on-board DAA with tip and ring connections, audio circuit for call-progress monitoring, and parallel interface. Note: The bolded, shaded pins are the active MT9234SMI-P (Parallel) pins. Comment [DAR51]: SM Analog Dial-up Parallel.wmf Top View – Parallel SocketModem Pins Pin Descriptions for a Parallel SocketModem Device Pin # Signal Tip Ring 24 –RESET 25 26 27 29 30 A1 DGND D7 D2 INT 31 32 A0 –WR 33 –RD 34 35 36 37 38 39 40 41 61 63 A2 D4 D5 D0 D1 D3 –DS D6 VCC AGND 64 SPKR I/O I/O I/O Description Telephone Line Interface – TIP Telephone Line Interface – RING Modem Reset (with pull-up). Active low –RESET input resets the SocketModem logic and returns AT command set to original factory defaults or to NVRAM 'stored values' . The modem is ready to accept commands within 6.5 seconds of power-on or reset. Reset must be asserted for a minimum of 30ms. Host Bus Address Line 1 GND Digital Ground Host Bus Data Line 7 Host Bus Data Line 2 Host Bus Interrupt Line. INT output is set high when the receiver error flag, receiver data available, transmitter holding register empty, or modem status interrupt have an active high condition. INT is reset low upon the appropriate interrupt service or master reset operation. Host Bus Address Line 0. Host Bus Write. –WR is an active low, write control input. When –DS is low, –WR low allows the host to write data or control words into a selected modem register. Host Bus Read. –RD is an active low, read control input. When –DS is low, –RD low allows the host to read status information or data from a selected modem register. Host Bus Address Line 2 Host Bus Data Line 4 Host Bus Data Line 5 Host Bus Data Line 0 Host Bus Data Line 1 Host Bus Data Line 3 Host Bus Device Select. –DS input low enables the modem for read or write. Host Bus Data Line 6 PWR +5 V or 3.3 V Supply (depends upon model). GND Analog Ground. This is tied common with DGND on the SocketModem. To minimize potential ground noise issues, connect audio circuit return to AGND. Speaker Output. SPKR is a single ended-output. It is tied to the CODEC through a series 6.8K resistor and .1uf cap. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 104 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) DC Electrical Characteristics 5V Serial – Standard (SMI) and Medical Device (SMI-HV) Build Options 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Digital Inputs –DTR (40), –TXD (35), –RTS (33) –Reset (24) Digital Outputs –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Digital Input Capacitance Input High Min 2.52V Input High Min 2.52V Output High Min 2.3V Input Low Max .9V Input Low Max 0.3V Output Low Max 0.4V Current Drive 2mA 5 pF 5V Parallel – Standard (SMI) and Medical Device (SMI-HV) Build Options 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Digital Inputs –DS (40) Digital Inputs (hysteresis input buffer) A0 (31), A1 (25), A2 (34), –WR (32), –RD (33) Digital Input / Output Output buffer can source 12 mA at 0.4 V DO (37), D1 (38), D2 (29), D3 (39), D4 (35), D5 (36), D6 (41), D7 (27) Digital Output INT (30) Digital Input Capacitance Input High Min 2.52V Input High Min 2.52V Input Low Max 0.9V Input Low Max 0.9V Input High Min 2.52V Input Low Max 0.9V Output High Min 2.3V Output Low Max 0.4V Current Drive 2mA 5 pF 3.3V Serial – Industrial Temperature (SMI-L) Build Option 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Digital Inputs –DTR (40), –TXD (35), –RTS (33) –Reset (24) Digital Outputs –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Digital Input Capacitance Input High Min 2.52V Input High Min 2.52V Input Low Max 0.9V Input Low Max 0.3V Output High Min. 2.3V Output Low Max 0.4V Current Drive 2mA 5 pF 3.3V Parallel – Industrial Temperature (SMI-L) Build Options 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Digital Inputs –DS (40) Digital Inputs (hysteresis input buffer) A0 (31), A1 (25), A2 (34), –WR (32), –RD (33) Digital Input/Output Output buffer can source 12 mA at 0.4 V DO (37), D1 (38), D2 (29), D3 (39), D4 (35), D5 (36), D6 (41), D7 (27) Digital Output INT (30) Digital Input Capacitance Input High Min 2.52V Input High Min 2.52V Input High Min 2.52V Input Low Max 0.9V Input Low Max 0.9V Input Low Max 0.9V Output High Min 2.3V Output Low Max 0.4V Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Current Drive 2mA 5 pF 105 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Parallel Timing Requirements Timing Requirements for Parallel Write Parameter –DS to –WR Setup (low to low) A0, A1, A2 to –WR Setup (valid to low) –WR Pulse Width (low to high) D0–D7 to –WR Setup (valid to high) –WR to –DS hold (high to high) –WR to A0–A2 Hold (high to invalid) –WR to D0–D7 Hold (high to invalid) –WR interaccess (high to low) Non-MIMIC Accesses MIMIC Accesses Min 10 15 40 30 Max Unit ns ns ns ns ns ns ns 10 110 ns ns Min 10 15 40 Max Unit ns ns ns ns ns 10 110 ns ns Timing Requirements for Parallel Read Parameter –DS to –RD Setup (low to low) A0, A1, A2 to –RD Setup (valid to low) –RD Pulse Width (low to high) –RD to –DS hold (high to high) –RD to A0–A2 Hold (high to invalid) –WR interaccess (high to low) Non-MIMIC Accesses MIMIC Accesses Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 106 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) SocketModem Parallel Interface Internal Registers The SocketModem parallel interface is a mimic of a 16C550A UART. It is similar to the MIMIC interface used in the Zilog Z80189. The SocketModem mimic (MMM) takes advantage of this standard interface while replacing the serial to parallel data transfer with a less complicated parallel to parallel data transfer. The MMM interface controls an 8-bit parallel data transfer which is typically interrupt driven. Interrupts usually indicate one or both of two conditions: (1) the receive (RX) FIFO has either reached a trigger level or time-out condition and needs to be emptied and/or (2) the transmit (TX) FIFO is empty and waiting for more data from the Host. An interrupt can also be triggered by a change in the modem status register (i.e., loss of carrier) or by the occurrence of errors in the line status register (overrun, parity, framing, break detect). In addition to the receive and transmit FIFOs, there are twelve other control/status registers called the MMM register set which can be accessed through this interface. Overview SocketModem MIMIC (MMM) Operation Data flow through MMM is bi-directional. Simultaneously, data can flow from the host through the transmit FIFO to the SocketModem controller, and data can flow from SocketModem controller through the receive FIFO to the Host. In the receive path, 8-bit data is asynchronously received (from the SocketModem controller) by the receive FIFO where it is stored along with associated three error bits. The error bits must arrive (via a SocketModem controller I/O write to MMM shadow line status register) prior to receiving the actual data bits. The error bits are then temporarily stored so they may be written, with associated data bits, to the 11-bit wide RX FIFO. After every data write, the RX FIFO write pointer is incremented. RX FIFO trigger levels, data ready signal, and time-out counter are checked to see if a Host-interrupt needs to be sent. The data ready signal will be activated and MMM sits poised to accept another data word. We highly recommend the host should read the MMM IIR register to determine the type of interrupt. Then it might check bit 7 of the LSR to see if there are any errors in the data currently residing in the receive FIFO. Finally, it will (1) alternately read a data word through the RX FIFO read pointer and the error bits via the MMM LSR until the FIFO is empty, or (2) read successive data words (knowing there were no errors in the FIFO) until the trigger count is met. A similar sequence occurs when data flows in the other direction (from host through transmit FIFO), except there is no error bit manipulation/checking involved. FIFO Operation The 16-byte transmit and receive data FIFOs are enabled by the FIFO Control Register (FCR) bit-0. You can set the receive trigger level via FCR bits 6/7. The receiver FIFO section includes a time-out function to ensure data is delivered to the external host. An interrupt is generated whenever the Receive Holding Register (RHR) has not been read following the loading of a character or the receive trigger level has been reached. Receive (RX) FIFO The RX FIFO can be configured to be 16 words deep and 11 bits wide. Each word in the RX FIFO consists of 8 data bits and 3 error bits. The RX block of the MMM contains read and write pointers and status flag circuitry that need only to be presented with data (for input), reset, read/write control signals, and read/write clock signals. The RX block of the MMM internally manages the FIFO register file and pointers, and it provides simultaneous read/write capability (no contention problems). The RX block of the MMM provides data (for output), FIFO full flag, FIFO empty flag, and an almost full flag which uses an associated predefined trigger level (obtained from the MMM FCR control register) to signal when the trigger level has been met. Four possible trigger levels may be selected by programming bits 6-7 of the FCR control register. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 107 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) A typical (interrupt driven) write to the RX block is a two-step process. The MMM micro-controller must first write the 3 error bits to a shadow MMM LSR status register. Next, the micro-controller writes the data to the RX FIFO and during this write operation, the 3 error bits are directly loaded from the LSR shadow register into the bits 8-10 of the selected (11 bit-wide) FIFO register. These error bits represent the parity error, framing error, and break interrupt signals associated with each data work transmission into the receive FIFO. When the receive FIFO is read, these error bits are loaded directly into bits 2-4 of the MMM LSR register. A2 A1 A0 Register Name RBR THR IER IIR FCR LCR MCR LSR MSR SCR DLL DLM DLX MCX Register Description Receive Buffer (RX FIFO) Transmit Holding (TX FIFO) Interrupt Enable Interrupt Identification FIFO Control Line Control Modem Control Line Status Modem Status Scratch pad LSB of Divisor Latch MSB of Divisor Latch Divisor Latch Status/Control Host Access DLAB = 0 R only DLAB = 0 W only DLAB = 0 R/W DLAB = X R only DLAB = X W only DLAB = X R/W DLAB = 0 R/W DLAB = X R only DLAB = X R only DLAB = 0 R/W DLAB = 1 R/W DLAB = 1 R/W DLAB = 1 R/W DLAB = 1 R/W Note 1* The General Register set is accessible only when DS is a logic 0. Note 2* The Baud Rate register set is accessible only when DS is a logic 0 and LCR bit-7 is a logic 1. Time Out Interrupts The interrupts are enabled by IER bits 0-3. Care must be taken when handling these interrupts. Following a reset the transmitter interrupt is enabled, the SocketModem will issue an interrupt to indicate that transmit holding register is empty. This interrupt must be serviced prior to continuing operations. The LSR register provides the current singular highest priority interrupt only. A condition can exist where a higher priority interrupt may mask the lower priority interrupt(s). Only after servicing the higher pending interrupt will the lower priority interrupt(s) be reflected in the status register. Servicing the interrupt without investigating further interrupt conditions can result in data errors. When two interrupt conditions have the same priority, it is important to service these interrupts correctly. Receive Data Ready and Receive Time Out have the same interrupt priority (when enabled by IER bit-3). The receiver issues an interrupt after the number of characters received have reached the programmed trigger level. In this case the MMM FIFO may hold more characters than the programmed trigger level. Following the removal of a data byte, the user should recheck LSR bit-0 for additional characters. A Receive Time Out will not occur if the receive FIFO is empty. The time out counter is reset at the center of each stop bit received or each time the receive holding register (RHR) is read. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 108 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Register Functional Definitions The following table delineates the assigned bit functions for the twelve internal registers. The assigned bit functions are more fully defined in the following paragraphs. Internal Registers A2 A1 A0 Register [Default] BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 Bit-2 Bit-2 Receive Line Status interrupt Interrupt ID XMIT FIFO reset Bit-1 Bit-1 Transmit Holding Register interrupt Interrupt ID RCVR FIFO reset Bit-0 Bit-0 Receive Holding Register interrupt Interrupt Pending FIFO enable Word length bit1 Word length bit-0 *3 General Register Set: Note 1* RBR [XX] THR [XX] IER [00] Bit-7 Bit-7 Bit-6 Bit-6 Bit-5 Bit-5 Bit-4 Bit-4 Bit-3 Bit-3 Modem Status Interrupt IIR [XX] FCR [00] LCR [00] FIFO enable RX trigger (LSB) Set break Detect change in FCR Stick parity TX FIFO overrun bit Even parity Interrupt ID DMA mode select Parity enable MCR [00] FIFO enable RX Trigger (MSB) Divisor latch access (DLAB) -RTS -DTR LSR [60] Parity error Overrun error Receive data ready MSR [X0] TX empty THR empty RI THR Empty RX FIFO data error CD INT enable Framing error OUT 1 Loop back Break interrupt DSR CTS Bit-6 Bit-5 Bit-4 Delta -CD Bit-3 Delta -RI Bit-2 Delta -DSR Bit-1 Delta -CTS Bit-0 Bit-6 Bit-6 Bit-5 Bit-5 Bit-4 Bit-4 Bit-3 Bit-3 Bit-2 Bit-2 Bit-1 Bit-1 Bit-0 Bit-0 1 1 1 SCR [FF] Bit-7 Special Register Set: Note *2 0 0 0 DLL [00] Bit-7 0 0 1 DLM [00] Bit-7 Note: 1* The General Register set is accessible only when DS is a logic 0. 2* The Baud Rate register set is accessible only when DS is a logic 0 and LCR bit-7 is a logic 1. 3* The value between the square brackets represents the register's initialized HEX value, X = N/A. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 109 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) RBR – Receive Buffer (RX FIFO) All eight bits are used for receive channel data (host read/data in; host write/data out). The three error bits per byte are copied into bits 2, 3, and 4 of the LSR during each host I/O read; therefore, they are available for monitoring on a per-byte basis. THR – Transmit Holding Register (TX FIFO) All eight bits are used for transmit channel data (host write/data out; host read/data in). IER – Interrupt Enable Bits 4–7: Reserved and will always read 0. Bits 0-3: Set by host software only and cleared by software control or host reset. Bit 3: Enables modem status IRQ. If bits 0–3 of the MSR are set and this bit is set to 1 (enabled), a host interrupt is generated. Bit 2: Enables receive line status IRQ. If bits 1–4 (overrun, parity, framing, break errors) of the LSR are set and this bit is set to a logic 1, a host interrupt is generated. Bit 1: Enables transmit holding register IRQ. If bit 5 (transmit holding register empty) of the LSR is set and this bit is set to a 1, a host interrupt is generated. Bit 0: Enables received data available IRQ. If bit 0 (data ready) of the LSR is set and this bit is set to a 1, a host interrupt is generated. IIR – Interrupt Identification (Read Only) Bits 6–7: (FIFO enabled bits). These bits will read a 1 if FIFO mode is enabled and the 16450 enable bit is 0 (no force of 16450 mode). Bits 4–5: Reserved and always read a 0. Bits 1–3: Interrupt ID bits. Bit 0: Interrupt pending. If logic 0 (in default mode), an interrupt is pending. When the host accesses IIR, the contents of the register are frozen. Any new interrupts will be recorded, but not acknowledged during the IIR access. This requires buffering bits (0–3, 6–7) during IIR reads. Interrupt Sources and Reset Control Table Bit 3 Bit 2 Bit 1 Priority Interrupt Source Interrupt Reset Control Highest Reading the LSR 2nd Overrun, parity, framing, error or break detect bits set by SocketModem Controller Received data trigger level nd 3rd th Receiver time-out with data in RX FIFO TX holding register empty MODEM status: CTS, DSR, RI or DCD RX FIFO drops below trigger level Read RX FIFO Writing to TX holding register or reading IIR when TX holding register is source of error Reading the MSR Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 110 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) FCR – FIFO Control Bits 6–7: Bit 5: Bit 4: Bit 3: Bit 2: Bit 1: Bit 0: Used to determine RX FIFO trigger levels. Used to detect a change in the FCR. TX FIFO overrun bit. DMA mode select. If bit 3 is a 0, the 16450 mode is enabled which does only single-byte transfers. When bit 3 is a 1, it enables a multiple byte (FIFO mode) data transfer. TX FIFO reset. This will cause TX FIFO pointer logic to be reset (any data in TX FIFO will be lost). This bit is self clearing; however, a shadow bit exists that is cleared only when read by the host, thus allowing the host to monitor a FIFO reset. RX FIFO reset. This will cause RX FIFO pointer logic to be reset (any data in RX FIFO will be lost). This bit is self clearing; however, a shadow bit exists that is cleared only when read by the host, thus allowing the host to monitor a FIFO reset. FIFO enable. The host writes this bit to logic 1 to put the block in FIFO mode. This bit must be a 1 when writing other bits in this register or they will not be programmed. When this bit changes state, any data in the FIFOs or the RBR and THR registers will be lost and any pending interrupts are cleared. Bit 7 Bit 6 16 Deep FIFO Trigger Levels (# of bytes) Default 14 LCR – Line Control Divisor latch access bit. This bit allows the host, access to the divisor latch. Under normal circumstances, the bit is set to 0 (provides access to the RX and TX FIFOs at address 0). If the bit is set to 1, access to transmitter, receiver, interrupt enable, and modem control registers is disabled. In this case, when an access is made to address 0, the divisor latch least (DLL) significant byte is accessed. Address 1 accesses the most significant byte (DLM). Address 7 accesses the DLX divisor latch register. Address 4 accesses the MCX status/control register. Bit 6: Used to denote a host-generated set break condition. Bits 0,1,3,4,5: Used only in parity bit generation for the 7 bit data byte case. Bits 0 and 1 are used for word length select (b0 = 0 and b1 = 1 is used for 7 bit data). Bit 3 is parity enable. Bit 4 is even parity select. Bit 5 is stick parity. Bit 7: MCR – Modem Control Bits 5–7: Bit 4: Bit 3: Bits 0–2: Bit 2: Bit 1: Bit 0: Reserved, and will always be 0. Used for loopback. When a 1, bits 0–3 of the MCR are reflected in modem status register (MSR) as follows: RI <= OUT1, DCD <= OUT2, DSR <= DTR, CTS <= RTS. Emulation of loopback feature of 16550 UART must be done by the host except for the above conditions. Also, when this bit is set, it allows for data loop back. This means the host can write a data word to the TX and immediately read back the same data word from the RX (in a manner similar to the 16550A). Controls the signal used to 3-state the host interrupt. If 0, then an active-low L33xV output will be set to 0, and this signal will be used to 3-state the host interrupt output pin. Used during LOOP function. OUT1. Request to Send (RTS). Data terminal ready (DTR). Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 111 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) LSR – Line Status Bit 7: Bit 6: Bit 5: Bits 2–4: Bit 1: Bit 0: Error in RX FIFO. This bit is always set to 1 if at least one data byte in the RX FIFO has an error. This will clear when there are no more errors in the RX FIFO. Transmitter empty. This bit is the same as LSR bit 5 (THRE) in MMM Transmitter holding register empty. This bit is set to 1 when either the transmitter holding register has been read (emptied) by the micro-controller (16450 mode) or the TX FIFO is empty (16550 mode). This bit is set to 0 when either the THR or the TX FIFO becomes not empty in 16450 mode. In 16550 mode, it is set to 0 only after the trigger level has been met since the last occurrence of TX FIFO empty. If the transmitter timer is enabled, a shadow bit exists which delays the timer setting this bit to 1. When reading this bit, the micro-controller will not see the delay. Both shadow and register bits are cleared when the host writes to the THR or TX FIFO in 16450 mode. The trigger level must be reached to clear the bit in 16550 (FIFO) mode. Used for parity error, framing error, and break detect. These bits are written, indirectly, by the micro-controller as follows: The bits are first written to the shadow bit locations when the microcontroller write accesses the LSR. When the next character is written to the receive buffer (RBR) or the RX FIFO, the data in the shadow bits is then copied to the RBR (16450 mode) or RX FIFO (16550 mode). In FIFO mode, bits become available to the host when the data byte associated with the bits is next to be read. In FIFO mode, with successive reads of the receiver, the status bits will be set if an error occurs on any byte. Once the micro-controller writes to the RBR or RX FIFO, the shadow bits are auto cleared. The register bits are updated with each host read. Overrun error. This bit is set if the micro-controller makes a second write to RBR before the host reads data in the buffer (16450 mode) or with a full RX FIFO (16550 mode). No data will be transferred to the RX FIFO under these circumstances. This bit is reset when the host reads the LSR. Data ready bit. This bit is set to 1 when received data is available, either in the RX FIFO (16550 mode) or the RBR (16450 mode). This bit is set immediately upon the micro-controller writing data to the RBR or FIFO if the receive timer is not enabled, but it is delayed by the timer interval if the receive timer is enabled. For micro-controller read access, a shadow bit exists so that the micro-controller does not see the delay that the host sees. Both bits are cleared to logic 0 immediately upon reading all data in either RBR or RX FIFO. MSR – Modem Status Bits 4 through 7 of the MSR can also take on the MCR bits 0 through 3 value when in MCR loop mode (i.e. when MCR b4 = 1). The transfer of bits in loop back has a null modem twist (i.e. MCR b0 goes to MSR b5 and MCR b1goes to MSR b4). Bit 7: Data carrier detect (DCD) bit. Bit 6: Ring indicator (RI) bit. Bit 5: Data set ready (DSR) bit. Bit 4: Clear to send (CTS) bit. Bit 3: Delta data carrier detect pin. This bit is set to a 1 whenever the data carrier detect bit changes state. It is reset when the host reads the modem status register. Bit 2: Trailing edge ring indicator bit. This bit is set to 1 on the falling edge of the ring indicator bit. It is reset when the host reads the modem status register. Bit 1: Delta data set ready bit. This bit is set to 1 whenever the data set ready changes state. It is reset when the host reads the modem status register. Bit 0: Delta clear to send bit. This bit is a one whenever the clear to send bit changes state. It is reset when the host reads the modem status register. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 112 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) SCR – Scratch The host programmer uses this register for temporary data storage. DLL – Divisor Latch (LSByte) This register contains low-order byte for the 16-bit clock divider. It is kept to maintain register set compatibility with the 16C550A interface. However, it is not used for clock generation since MMM does not require the generation of a real baud clock. DLM – Divisor Latch (MSByte) This register contains high-order byte for the 16-bit clock divider. It is kept to maintain register set compatibility with the 16C550A interface. However, it is not used for clock generation, since MMM does not require the generation of a real baud clock. Programming the Baud Rate Generator Registers DLM (MSB) and DLL (LSB) provides a user capability for selecting the desired final baud rate. The example in the Table below shows the selectable baud rates available when using a 1.8432 MHz external clock input. BAUD RATE GENERATOR PROGRAMMING TABLE Baud Rate 110 300 600 1200 2400 4800 9600 19.2K 38.4K 57.6K 115.2K 16 x Clock Divisor (Decimal) DLM Value (HEX) DLL Value (HEX) 1047 384 192 96 48 24 12 04 01 00 00 00 00 00 00 00 00 00 17 80 C0 60 30 18 0C 06 03 02 01 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 113 PART 3 – Embedded Analog SocketModems Chapter 6 – SocketModem (MT9234SMI) Application Notes Tip and Ring Interface Comment [DAR52]: This is the new Tip and Ring done 2008 Comment [DAR53]: Tip_and_Ring _New_2008.png Rev. I OEM Motherboard Filtering and Surge Protection Options See Design Considerations and Recommended Parts in Chapter 1. Recommended Uses for Filtering Options • Enhanced Surge Protection with RJ-11 Filtering Use this option when additional lightning protection may be needed. • Alternate Common Mode with RJ-11 Filtering Use this option when your design has common mode emission issues. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 114 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Chapter 7 – SocketModem® (MT5692SMI) Introduction This chapter covers the SocketModem® MT5692SMI and its various builds: serial, parallel, voice. The serial build option can be ordered with or without IP functionality. The Multi-Tech SocketModem creates communication-ready devices by integrating data/fax/voice functionality into a single product design. The SocketModem is a space-efficient (1" × 2.5"), embedded modem that provides V.92 or V.34/33.6K data communication. The complete, ready-to-integrate modem dramatically reduces development time and costs for system designers. The MT5692SMI SocketModem is a standard 64-pin modem used for integrating data communications. • It is a single-port modem that integrates the controller, DSP, and DAA in a 1" x 2.5" form factor and communicates to a host controller via an asynchronous serial interface. • It is available with an 8-bit parallel interface. The SocketModem IP, MT5692SMI-IP, embedded modem creates Internet-ready devices by integrating modem functionality and a complete TCP/IP protocol stack into a single, universal socket design. This embedded modem sends and receives data via e-mail, HTTP, or socket interfaces. It also complies with telecom requirements globally allowing for worldwide shipments. Product Build Options and Ordering Information Product Description Region Order this Product MT5692SMI Serial Builds MT5692SMI-34 MT5692SMI-L-34 MT5692SMI-92 MT5692SMI-L-92 MT5692SMI-X-L-92 IP Builds MT5692SMI-IP-92 MT5692SMI-IP-L-92 Voice Builds MT5692SMI-V-34 MT5692SMI-V-92 Parallel Builds MT5692SMI-P-34 MT5692SMI-P-L-34 MT5692SMI-P-92 MT5692SMI-P-L-92 MTSMI-UDK MTSMI-P-UDK V.34 Serial Data / V.17 Fax, 5V V.34 Serial Data / V.17 Fax, 3.3V V.92 Serial Data / V.17 Fax, 5V V.92 Serial Data / V.17 Fax, 3.3V V.92 Serial Data / V.17 Fax, 3.3V (excludes LED pins) Global Global Global Global Global V.92 Serial Data-Only 5V V.92 Serial Data-Only, 3.3V Global Global V.34 Serial Data / V.17 Fax / Voice, 5V V.92 Serial Data / V.17 Fax / Voice, 5V Global Global V.34 Parallel Data / V.17 Fax, 5V V.34 Parallel Data / V.17, 3.3V V.92 Parallel Data / V.17 Fax, 5V V.92 Parallel Data / V.17 Fax, 3.3V Developer Kits SocketModem Serial Developer Kit SocketModem Parallel Developer Kit Global Global Global Global Global Global How to Read the Product Codes in the Above Table: 34 V.34 data rate 92 V.92/56K data rate 3.3V power input (default is 5V) Parallel interface (default is serial) Speakerphone I/O Excludes LED pins IP Embedded Universal IP Stack UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MT5692SMI-V-34.Rx. “R” indicates product revision. “x” is the revision number. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 115 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) AT Commands Reference Guide Product SocketModem (MT5692SMI) SocketModem (MT5692SMI-IP) Reference Guides Title and Document Product Number MT5692SMI AT Commands Reference Guide (S000468x) Universal IP AT Commands Reference Guide (S000457x) Fax Commands Voice Commands Included in S000468x Included in S000468x NA Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) NA 116 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Technical Specifications MT5692SMI, MT5692SMI-V, MT5692SMI-P, MT5692SMI-IP The MT5692SMI, MT5692SMI-V, MT5692SMI-P, and MT5692SMI-IP SocketModems meet the following specifications: Category Description Data Standards V.92, V.34, V.32bis, V.32, V.23, V.23 half-duplex, V.23 reverse, V.22bis, V.22bis Fast Connect, V.22, V.21, Bell 212A/Bell 103, V.29 FastPOS, V.80 Synchronous Access Mode (V.80 not for IP build) Data Format All Builds: Serial, asynchronous Parallel Build: 8-bit parallel interface Character Format 10 bit Serial/Data Speeds All Builds Except IP: Supports DTE speeds up to 230.4K bps, autobaud up to 115.2K bps For IP Build: Supports DTE speeds up to 921.6K bps, Comment [DAR54]: 115.2K bps came from Mike L. 7/14/09 Client-to-Client Data Rates 33600, 31200, 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000, 9600, 7200, 4800, 2400, 1200, 0-300 bps Comment [DAR55]: 921.6K bps came from Mike L. 7/14/09 Data Error Correction V.42 LAPM and MNP 2–4 Data Compression V.44, V.42bis, MNP 5 Fax Compatibility All Builds Except IP: V.17, V.29, V.27ter, V.21 channel 2 Fax Class All Builds Except IP: Class 1, Class 1.0 Modes of Operation Full duplex over dial-up lines; data mode, command mode, online command mode Size 2.54" (64.541 mm) x 1.045" (26.543 mm) Weight 0.6 oz. (0.017 kg.) Operating Temperature -40º to +85° C Storage Temperature -40º to +85° C Humidity 20% to 90% (non-condensing) Operating Voltage Transmit Level 3.3V or 5V Note: Voice modules are available with 5V only -12 dBm (varies by country) Receiver Sensitivity -43 dBm under worst-case conditions DAA Isolation 1.5Kv r.m.s. or 2121 VDC at working voltage of 250VAC Flow Control All Builds Except IP: XON/XOFF (software), RTS/CTS (hardware) Command Buffer 60 characters Telephony/TAM V.253 commands 8 kHz sample rate Concurrent DTMF, distinctive ring, and "Bell Core Type 1" Caller ID 8-bit μ-law and A-law PCM coding Supports PCM Encoding: 2-bit and 4-bit ADPCM, 8-bit and 16-bit linear PCM, and 4-bit IMA coding Compliance EMC Compliance FCC Part 15 (Class B) ICES-003 (Class B) EN 55022 (Class B) EN 55024 Safety Compliance UL 60950-1 cUL 60950-1 EN 60950-1 AS/NZS 60950:2000 Telecom 47 CFR Part 68 CS-03 R&TTE A-Tick (Other countries included per the Modem Globalization Guide) 2 years Warranty Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 117 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Category Description Intelligent Features V.22bis Fast Connect V.29 FastPOS Voice send and receive functions LED pin output option DTMF detection and distinctive ring Audio circuit outputs for audio call-progress monitoring Three-number storage for automatic dialing capabilities and non-volatile memory (NoVRAM) to store user profiles Speaker interface for call progress monitoring Full-duplex data transmission over dial-up lines Line quality monitoring and retrain Line protection circuitry included Auto-dial, redial, and auto-answer, pulse or tone dial, call status display Extension pickup detection Remote hang-up detection Line-in-use detection Digital PBX detection and protection 60-character command line buffering Auto-parity and data rate selections AT command compatibility Global approvals with a single SocketModem design Intelligent DAA technology detects line status Supports speakerphone I/O Supports "Bell Core Type 1" Caller ID Modem mode bypasses the IP features Flash memory to update firmware with the latest enhancements For IP Build Only: Internet Protocols Supported: Dial-in PPP, DNS, FTP, ICMP,IP, LCP, PPP, SMTP, SNTP, TCP, UDP Socket Dial-in PPP using remote dial-up networking Authentication Protocols: CHAP, Dial-up Script, PAP Binary Base 64 encoding and MIME email formats Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 118 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Pin Outs Serial Build (MT5692SMI and MT5692SMI-IP) Top View -- SocketModem Pin Out For pin descriptions, see the Universal Pin Out Description in Chapter 1. Serial with Voice Build (MT5692SMI-V) Top View – SocketModem with Voice Pin Out For pin descriptions, see the Universal Pin Out Description in Chapter 1. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 119 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Parallel Build (MT5692SMI-P) Top View – SocketModem with Parallel Build Pin Out For pin descriptions, see the Universal Pin Out Description in Chapter 1. Parallel Pin Descriptions Pin # 24 Signal Name Tip Ring –RESET 25 26 27 29 30 31 32 33 34 35 36 37 38 39 A1 DGND D7 D2 INT A0 –WR –RD A2 D4 D5 D0 D1 D3 In Out Type I/O I/O GND Description Telephone Line Interface – TIP Telephone Line Interface – RING Modem Reset (CMOS input with pull-up). The active low –RESET input resets the SocketModem logic and returns the AT command set to the original factory default values or to "stored values" in NVRAM. The modem is ready to accept commands within 6.5 seconds of power-on or reset. Host Bus Address Line 1 Digital Ground Host Bus Data Line 7 Host Bus Data Line 2 Host Bus Interrupt Line (Active High, Resets on Low) Host Bus Address Line 0 Host Bus Write. When low, allows host to write to SocketModem. Host Bus Read. When low, allows host to read from SocketModem. Host Bus Address Line 2 Host Bus Data Line 4 Host Bus Data Line 5 Host Bus Data Line 0 Host Bus Data Line 1 Host Bus Data Line 3 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Comment [DAR56]: This sentence removed from reset by Dustin 8/24/09 Reset must be asserted for a minimum of 15ms. 120 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Parallel Pin Descriptions Continued Pin # 40 41 61 62 Signal Name –DS D6 VCC MICV In Out Type PWR 63 AGND GND 64 SPKR Description Host Bus Device Select (or Chip Select) (Active Low) Host Bus Data Line 6 3.3 V or 5 V Supply (depends upon model). Single-Ended Microphone. Single-ended microphone input for dial-up SocketModem speakerphone and TAM functions. Analog Ground. This is tied common with DGND on the SocketModem. To minimize potential ground noise issues, connect audio circuit return to AGND. Speaker – Call monitor. Operating Conditions Parameter 5V Supply Range – Vcc 3.3V Supply Range – Vcc Minimum 4.5V 3.135V Maximum 5.5V 3.465V Absolute Maximum Rating Parameter Voltage at Any Signal Pin Minimum GND -0.3V Maximum Vcc +3.3V DC Electrical Characteristics 5V SocketModem 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Parameter Input Low Level –DS (40) Input High Level A0 (31), A1 (25), –WR (32), –RD (33) Output Low Level DO (37), D1 (38), D2 (29), D3 (39), D4 (35), D5 (36), D6 (41), D7 (27) Output High Level INT (30) Digital Input Capacitance – 50pF Minimum -0.3V Maximum 0.8V 2.2V Vcc NA 0.4V 2.4V NA Minimum -0.3V Maximum 0.8V 2V Vcc NA 0.4V 2V NA 3.3 V SocketModem 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Parameter Input Low Level –DS (40) Input High Level A0 (31), A1 (25), A2 (34), –WR (32), –RD (33) Output Low Level DO (37), D1 (38), D2 (29), D3 (39), D4 (35), D5 (36), D6 (41), D7 (27) 2 mA, Z INT = 120 Ω Output High Level INT (30) 2 mA, Z INT = 120 Ω Digital Input Capacitance – 50pF Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 121 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Power* Measurements Serial Build – MT5692SMI Input Voltage: 3.3V Current (AMPS) Watts Sleep Mode 0.014 0.046 Typical 0.069 0.216 Maximum 0.080 0.249 Sleep Mode 0.018 0.089 Typical 0.074 0.359 Maximum 0.088 0.425 Input Voltage: 5V Current (AMPS) Watts Comment [DAR57]: This were updated on 10/16/09 with new info from Tom Fix. Serial with IP Build – MT5692SMI-IP Input Voltage: 3.3V Current (AMPS) Watts Sleep Mode 0.047 0.151 Typical 0.101 0.316 Maximum 0.112 0.349 Sleep Mode 0.052 0.256 Typical 0.109 0.528 Maximum 0.121 0.583 Sleep Mode 0.016 0.080 Typical 0.076 0.380 Maximum 0.089 0.445 Sleep Mode 3.30 0.015 0.051 Typical 3.29 0.072 0.236 Maximum 3.29 0.081 0.267 Sleep Mode 4.91 0.014 0.068 Typical 4.86 0.069 0.334 Maximum 4.84 0.079 0.380 Input Voltage: 5V Current (AMPS) Watts Voice Build – MT5692SMI-V Note: The voice build is not available in 3.3V. Input Voltage: 5V Current (AMPS) Watts Parallel Build – MT5692SMI-P Input Voltage: 3.3V Measured Voltage Current (AMPS) Watts Input Voltage: 5V Measured Voltage Current (AMPS) with 5V Watts Note: Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 122 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Parallel Host Bus Timing Table Symbol AS AH CS CH RD DD DRH Parameter Min READ (See Notes) Address Setup Address Hold Chip Select Setup Chip Select Hold RD Strobe Width 77 Read Data Delay 10 Read Data Hold WRITE (See Notes) Address Setup Address Hold Chip Select Setup Chip Select Hold 10 WT Strobe Width 15 Write Data Setup (see Note 4) 15 Write Data Hold (see Note 5) Max Units 25 ns ns ns ns ns ns ns AS ns AH ns CS ns CH ns WT ns DS 20 ns DWH ns Notes: 1. When the host executes consecutive Rx FIFO reads, a minimum delay of 2 times the internal CPU clock cycle plus 15 ns (85.86 ns at 28.224 MHz) is required from the falling edge of RD to the falling edge of the next Host Rx FIFO RD clock. 2. When the host executes consecutive Tx FIFO writes, a minimum delay of 2 times the internal CPU clock cycle plus 15 ns (85.86 ns at 28.224 MHz) is required from the falling edge of WT to the falling edge of the next Host Tx FIFO WT clock. 3. tRD' tWT = tCYC + 15 ns. 4. DS is measured from the point at which both CS and WT are active. 5. tDWH is measured from the point at which either CS and WT become active. 6. Clock Frequency = 1.8432 MHz clock. Parallel Host Bus – Read Comment [DAR58]: Changed by Mike McNeil 7/9/09- Parallel Host Bus Timing Table - For READ change, Address Hold to 5, Chip Select Setup to 5, Chip Select Hold to 0, RD Strobe Width to 77, Read Data Delay to 10. For WRITE change, Address Hold to 5, WT Strobe Width to 15, Write Data Setup to 15. - 6. Clock Frequency is 1.8432MHz. Parallel Host Bus - Write Comment [DAR59]: Parallel_Host_ Bus_Read.bmp 31KB Comment [DAR60]: Parallel_host_ Bus_Write.bmp 31Kb Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 123 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) SocketModem Parallel Interface The modem supports a 16550A interface in parallel interface versions. The 16550A interface can operate in FIFO mode or non-FIFO mode. Non-FIFO mode is the same as the 16450-interface operation. FIFO mode’s unique operations are described in this chapter. Overview The modem emulates the 16450/16550A interface and includes both a 16-byte receiver data first-in first-out buffer (RX FIFO) and a 16-byte transmit data first-in first-out buffer (TX FIFO). FIFO Mode Selected When FIFO mode is selected in the FIFO Control Register (FCR0 = 1), both FIFOs are operative. Furthermore, when FIFO mode is selected, DMA operation of the FIFO can also be selected (FCR3 = 1). FIFO Mode Not Selected When FIFO mode is not selected, operation is restricted to a 16450-interface operation. Receive Data Received Data is read by the host from the Receiver Buffer (RX Buffer). The RX Buffer corresponds to the Receiver Buffer Register in a 16550A device. In FIFO mode, the RX FIFO operates transparently behind the RX Buffer. Interface operation is described with reference to the RX Buffer in FIFO and non-FIFO modes. Transmit Data Transmit Data is loaded by the host into the Transmit Buffer (TX Buffer). The TX Buffer corresponds to the Transmit Holding Register in a 16550A device. In FIFO mode, the TX FIFO operates transparently behind the TX Buffer. Interface operation is described with reference to the TX Buffer in both FIFO and non-FIFO modes. Receiver FIFO Interrupt Operation Receiver Data Available Interrupt When the FIFO mode is enabled (FCR0 = 1) and receiver interrupt (RX Data Available) is enabled (IER0 = 1), receiver interrupt operation is as follows: 1. The Receiver Data Available Flag (LSR0) is set as soon as a received data character is available in the RX FIFO. LSR0 is cleared when RX FIFO is empty. 2. The Receiver Data Available Interrupt code (IIR0-IIR4 = 4h) is set whenever the number of received data bytes in the RX FIFO reaches the trigger level specified by FCR6-FCR7 bits. It is cleared whenever the number of received data bytes in the RX FIFO drops below the trigger level specified by FCR6-FCR7 bits. 3. The HINT interrupt is asserted whenever the number of received data bytes in the RX FIFO reaches the trigger level specified by FCR6-FCR7 bits. HINT interrupt is de-asserted when the number of received data bytes in the RX FIFO drops below the trigger level specified by FCR6-FCR7 bits. Receiver Character Timeout Interrupts When the FIFO mode is enabled (FCR0 = 1) and receiver interrupt (Receiver Data Available) is enabled (IER0 = 1), receiver character timeout interrupt operation is as follows: 1. A Receiver character timeout interrupt code (IIR0-IIR3 = Ch) is set if at least one received character is in the RX FIFO, the most recent received serial character was longer than four continuous character times ago (if 2 stop bits are specified, the second stop bit is included in this time period), and the most recent host read of the RX FIFO was longer than four continuous character times ago. Transmitter FIFO Interrupt Operation Transmitter Empty Interrupt When the FIFO mode is enabled (FCR0 = 1) and transmitter interrupt (TX Buffer Empty) is enabled (IER0 =1), transmitter interrupt operation is as follows: 1. The TX Buffer Empty interrupt code (IIR0-IIR3 = 2h) will occur when the TX Buffer is empty. It is cleared when the TX Buffer is written to (1 to 16 characters) or the IIR is read. 2. The TX Buffer Empty indications will be delayed 1 character time minus the last stop bit time whenever the following occur: THRE = 1 and there have not been at least two bytes at the same time in the TX FIFO Buffer since the last setting of THRE was set. The first transmitter interrupt after setting FCR0 will be immediate. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 124 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Register Functional Definitions The following table delineates the assigned bit functions for the twelve internal registers. The assigned bit functions are more fully defined in the following paragraphs. Internal Registers Register No. (DLAB = 0) (DLAB = 0) (DLAB = 0) (DLAB = 1) (DLAB = 1) Register Name Scratch Register (SCR) Modem Status Register (MSR) BIT No. Scratch Register Data Carrier Detect (DCD) RX FIFO Error Delta Data Delta Clear Clear to Delta Data Trailing to Send Send Carrier Edge of Ring Set Ready Indicator (DDSR) (DCTS) CTS) Detect (TERI) (DDCD) Line Status Transmitter Transmitter Break Framing Parity Overrun Receiver Register (LSR) Empty Buffer Interrupt Error Error Error Data (TEMT) Register (BI) (FE) (PE) (OE) Ready Empty (DR) (THRE) Modem Control Local Out 2 Out 1 Request Data Register (MCR) Loopback to Send Terminal (RTS) Ready (DTR) Line Control Divisor Set Stick Even Parity Number Word Word Register (LCR) Latch Break Parity Parity Enable of Stop Length Length Access Bit Select (PEN) Bits Select Select (DLAB) (EPS) (STB) Bit 1 Bit 0 (WLS1) (WLSO) Interrupt Identify FIFOs FIFOs Pending Pending Pending “0” if Register (IIR) Enabled Enabled Interrupt ID Interrupt ID Interrupt ID Interrupt (Read Only) Bit 2 Bit 1 Bit 0 Pending FIFO Control Receiver Receiver Reserved Reserved DMA TX FIFO RX FIFO FIFO Register (FCR) Trigger Trigger Mode Reset Reset Enable (Write Only) MSB LSB Select Interrupt Enable Enable Enable Enable Enable Register (IER) Modem Receiver Transmitter Received Status Line Status Holding Data Interrupt Interrupt Register Available (EDSSI) (ELSI) Empty Interrupt Interrupt (ERBFI) (ETBEI) Transmitter Buffer Transmitter FIFO Buffer Register (Write Only) Register (THR) Receiver Buffer Receiver FIFO Buffer Register (Read Only) Register (RBR) Divisor Latch MSB Divisor Latch MSB Register (DLM) Divisor Latch LSB Divisor Latch LSB Register (DLL) Ring Indicator (RI) Data Set Ready (DSR) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 125 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) IER – Interrupt Enable Register (Addr = 1, DLAB = 0) The IER enables five types of interrupts that can separately assert the HINT output signal (See the Interrupt Sources and Reset Control table in the IIR section of this chapter). A selected interrupt can be enabled by setting the corresponding enable bit to a 1, or disabled by setting the corresponding enable bit to a 0. Disabling an interrupt in the IER prohibits setting the corresponding indication in the IIR and assertion of HINT. Disabling all interrupts (resetting IER0 – IER3 to a 0) inhibits setting of any Interrupt Identifier Register (IIR) bits and inhibits assertion of the HINT output. All other system functions operate normally, including the setting of the Line Status Register (LSR) and the Modem Status Register (MSR). The IER enables five types of interrupts that can separately assert the HINT output signal. A selected interrupt can be enabled by setting the corresponding enable bit to a 1, or disabled by setting the corresponding enable bit to a 0. Disabling an interrupt in the IER prohibits setting the corresponding indication in the IIR and assertion of HINT. Disabling all interrupts (resetting IER0 - IER3 to a 0) inhibits setting of any Interrupt Identifier Register (IIR) bits and inhibits assertion of the HINT output. All other system functions operate normally, including the setting of the Line Status Register (LSR) and the Modem Status Register (MSR). Bits 7-4 Bit 3 Bit 2 Bit 1 Bit 0 Not used. Always 0. Enable Modem Status Interrupt (EDSSI). This bit, when a 1, enables assertion of the HINT output whenever the Delta CTS (MSR0), Delta DSR (MSR1), Delta TER (MSR2), or Delta DCD (MSR3) bit in the Modem Status Register (MSR) is a 1. This bit, when a 0, disables assertion of HINT due to setting of any of these four MSR bits. Enable Receiver Line Status Interrupt (ELSI). This bit, when a 1, enables assertion of the HINT output whenever the Overrun Error (LSR1), Parity Error (LSR2), Framing Error (LSR3), or Break Interrupt (LSR4) receiver status bit in the Line Status Register (LSR) changes state. This bit, when a 0, disables assertion of HINT due to change of the receiver LSR bits 1-4. Enable Transmitter Holding Register Empty Interrupt (ETBEI). This bit, when a 1, enables assertion of the HINT output when the Transmitter Empty bit in the Line Status Register (LSR5) is a 1.This bit, when a 0, disables assertion of HINT due to LSR5. Enable Receiver Data Available Interrupt (ERBFI) and Character Timeout in FIFO Mode. This bit, when a 1, enables assertion of the HINT output when the Receiver Data Ready bit in the Line Status Register (LSR0) is a1 or character timeout occurs in the FIFO mode. This bit, when a 0, disables assertion of HINT due to the LSR0 or character timeout. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 126 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) FCR – FIFO Control Register (Addr = 2, Write Only) The FCR is a write-only register used to enable FIFO mode, clear the RX FIFO and TX FIFO, enable DMA mode, and set the RX FIFO trigger level. Bits 7-6 FCR7 RX FIFO Trigger Level FCR7 and FCR6 set the trigger level for the RX FIFO (Receiver Data Available) interrupt. FCR6 RX FIFO Trigger Level (Bytes) 01 04 08 14 Bits 5, 4 Not used Bit 3 DMA Mode Select When FIFO mode is selected (FCR0 = 1), FCR3 selects non-DMA operation (FCR3 = 0) or DMA operation (FCR3 = 1). When FIFO mode is not selected (FCR0 = 0), this bit is not used (the modem operates in non-DMA mode in 16450 operation). DMA Operation in FIFO Mode RXRDY will be asserted with the number of characters in the RX FIFO us equal to or greater than the value in the RX FIFO Trigger Level (IIR0-IIR3 = 4h) or the received character timeout (IIRO-IIR3 = Ch) has occurred. RXTDY will go inactive when there are no more characters in the RX FIFO. TXRDY will be asserted when there are one or more empty (unfilled) locations in the TX FIFO. TXRDY will go inactive when the TX FIFO is completely full. Non-DMA Operation in FIFO Mode RXRDY will be asserted when there are one or more characters in the RX FIFO. RXRDY will go inactive when there are no more characters in the RX FIFO. TXRDY will be asserted when there are no characters in the TX FIFO. TXRDY will go inactive when the character is loaded into the TX FIFO Buffer. Bit 2 TX FIFO Reset When FCR2 is a 1, all bytes in the TX FIFO are cleared. This bit is cleared automatically by the modem. Bit 1 RX FIFO Reset When FCR1 is a 1, all bytes in the RX FIFO are cleared. This bit is cleared automatically by the modem. Bit 0 FIFO Enable When FCR0 is a 0, 16450 mode is selected and all bits are cleared in both FIFOs. When FCR0 is a 1, FIFO mode (16550A) is selected and both FIFOs are enabled. FCR0 must be a 1 when other bits in the FCR are written or they will not be acted upon. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 127 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) IIR – Interrupt Identifier Register (Addr = 2) The Interrupt Identifier Register (IIR) identifies the existence and type of up to five prioritized pending interrupts. Four priority levels are set to assist interrupt processing in the host. The four levels, in order of decreasing priority, are Highest: Receiver Line Status, 2: Receiver Data Available or Receiver Character Timeout. 3: TX Buffer Empty, and 4: Modem Status. When the IIR is accessed, the modem freezes all interrupts and indicates the highest priority interrupt pending to the host. Any change occurring in interrupt conditions are not indicated until this access is complete. Bits 7-6 FIFO Mode These two bits copy FCR0. Bits 5-4 Not Used Always 0. Bits 3-1 Highest Priority Pending Interrupt These three bits identify the highest priority pending interrupt (Table below). Bit 3 is applicable only when FIFO mode is selected; otherwise, bit 3 is a 0. Bit 0 Interrupt Pending When this bit is a 0, an interrupt is pending; IIR bits 1-3 can be used to determine the source of the interrupt. When this bit is a 1, an interrupt is not pending Interrupt Sources and Reset Control Table Interrupt Identification Register Bit 3 Bit 2 Bit 1 Bit 0 Priority (Note 1) Level — Highest Note: Interrupt Set and Reset Functions Interrupt Type Interrupt Source Interrupt Reset Control None None — Reading the LSR Receiver Line Overrun Error (OE) Status (LSR1), Parity Error (PE) (LSR2), Framing Error (FE) (LSR3), or Break Interrupt (BI) (LSR4) Reading the RX Received Data Received Data Available Available (LSR0) Buffer or the RX FIFO drops below or RX FIFO Trigger the Trigger Level Level (FCR6-FCR7) Reached Reading the RX Character Timeout The RX FIFO contains at least 1 Buffer Indication1 character and no characters have been removed from or input to the RX FIFO during the last 4 character times. TX Buffer Empty TX Buffer Empty Reading the IIR or writing to the TX Buffer Reading the MSR Modem Status Delta CTS (DCTS) (MSR0), Delta DSR (DDST) (MSR1), Trailing Edge Ring Indicator (TERI) (MSR3), or Delta DCD (DCD) (MSR4) 1. FIFO Mode only. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 128 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) LCR – Line Control Register (Addr = 3) The Line Control Register (LCR) specifies the format of the asynchronous data communications exchange. Bit 7 Divisor Latch Access Bit (DLAB) This bit must be set to a 1 to access the Divisor Latch Registers during a read or write operation. It must be reset to a 0 to access the Receiver Buffer, the Transmitter Buffer, or the Interrupt Enable Register. Bit 6 Set Break When bit 6 is a 1, the Transmit data is forced to the break condition, i.e., space (0) is sent. When bit 6 is a 0, break is not sent. The Set Break bit acts only on the Transmit data and has no effect on the serial in logic. Bit 5 Stick Parity When Parity is enabled (LCR3 = 1) and stick parity is selected (LCR5 = 1), the parity bit is transmitted and checked by the receiver as a 0 if even parity is selected (LCR4 – 1) or a 1 if odd parity is selected (LCR4 = 0). When the stick parity is not selected (LCR3 = 0), parity is transmit and checked as determined by the LCR3 and LCR4 bits. Bit 4 Even Parity Select (EPS) When parity is enabled (LCR3 = 1) and stick parity is not selected (LCR5 = 0), the number of 1s transmitted or checked by the receiver in the data word bits and parity bit is either even (LCR4 = 1) or odd (LCR4 = 0). Bit 3 Enable Parity (PEN) When bit 3 is a 1, a parity bit is generated in the serial out (transmit) data stream and checked in the serial in (receive) data stream as determined by the LCR4 and LCR5 bits. The parity bit is located between the last data bit and the first stop bit. Bit 2 Number of Stop GBITS (STB) This bit specifies the number of stop bits in each serial out character. If bit 2 is a 0, one stop bit is generated regardless of word length. If bit 2 is a 1 and 5-bit word length is selected, one and one-half stop bits are generated. If bit 2 is a 1 and 6-, 7-, or 8-bit word length is selected, two stop bits are generated. The serial in logic checks the first stop bit only, regardless of the number of stop bits selected. Bit 1-0 Bit 1 Word Length Select (WLS0 and WLS1) These two bits specify the number of bits in each serial in or serial out character. The encoding of bits 0 and 1 is: Bit 0 Word Length 5 Bits (Not supported) 6 Bits (Not supported) 7 Bits 8 Bits Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 129 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) MCR – Modem Control Register (Addr = 4) The Modem Control Register (MCR) controls the interface with modem or data set. Bit 7-5 Not used Always 0 Bit 4 Local Loopback When this bit is set to a 1, the diagnostic mode is selected and the following occurs: 1. Data written to the Transmit Buffer is looped back to the Receiver Buffer. 2. The DTS (MCR0), RTS (MCR1), Out1 (MCR2), and Out2 (MCR3) modem control register bits are internally connected to the DSR (MSR5), CTS (MSR4), RI (MSR6), and DCD (MSR7) modem status register bits, respectively. Bit 3 Output 2 When this bit is a 1, HINT is enabled. When this bit is a 0, HINT is in the high impedance state. Bit 2 Output 1 This bit is used in local loopback (see MCR4). Bit 1 Request to Send (RTS) This bit controls the Request to Send (RTS) function. When this bit is a 1, RTS is on. When this bit is a 0, RTS is off. Bit 0 Data Terminal Ready (DTR) This bit controls the Data Terminal Ready (DTR) function. When this bit is a 1, DTR is on. When this bit is a 0, DTR is off. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 130 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) LSR – Line Status Register (Addr = 5) This 8-bit register provides status information to the host concerning data transfer Bit 7 RX FIFO Error In the 16450 mode, this bit is not used and is always 0. In the FIFO mode, this bit is set if there are one or more characters in the RX FIFO with parity error, framing error, or break indication detected. This bit is reset to a 0 when the host reads the LSR and note of the above conditions exist in the RX FIFO. Bit 6 Transmitter Empty (TEMT) This bit is set to a 1 whenever the TX Buffer (THR) and equivalent of the Transmitter Shift Register (TRS) are both empty. It is reset to a 0 whenever either the THR or the equivalent of the TSR contains a character. In the FIFO mode, this bit is set to a 1 whenever the TX FIFO and the equivalent of the TSR are both empty Bit 5 Transmitter Holding Register Empty (THRE) [TX Buffer Empty] This bit, when set, indicates that the TX Buffer is empty and the modem can accept a new character for transmission. In addition, this bit causes the modem to issue an interrupt to the host when the Transmit Holding Register Empty Interrupt Enable bit (IIR1) is set to 1. The THRE bit is set to a 1 when a character is transferred from the TX Buffer. The bit is reset to 0 when a byte is written into the TX Buffer by the host. In the FIFO mode, this bit is set when the TX FIFO is empty; it is cleared when at least one byte is in the TX FIFO. Bit 4 Break Interrupt (BI) This bit is set to a 1 whenever the received data input is a space (logic 0) for longer than two full word lengths plus 3 bits. The BI is reset when the host reads the LSR. Bit 3 Framing Error (FE) This bit indicates that the received character did not have a valid stop bit. The FE bit is set to a 1 whenever the stop bit following the last data bit or parity bit is detected as a logic o (space). The FE bit is reset to a 0 when the host reads the LSR. In the FIFO mode, the error indication is associated with the particular character in the FIFO it applies to. The FE bit set to a 1 when this character is loaded into the RX Buffer. Bit 2 Parity Error (PE) This bit indicates that the received data character in the RX Buffer does not have the correct even or odd parity, as selected by the Even Parity Select bit (LCR4) and the Stick Parity bit (LCR5). The PE bit is reset to a 0 when the host reads the LSR. In the FIFO mode, the error indication is associated with the particular character in the FIFO it applies to. The PE bit set to a 1 when this character is loaded into the RX Buffer. Bit 1 Overrun Error (OE) This bit is set to a 1 whenever received data is loaded into the RX Buffer before the host has read the previous data from the RX Buffer. The OE is reset to a 0 when the host reads the LSR. In the FIFO mode, if data continues to fill beyond the trigger level, an overrun condition will occur only if the RX FIFO is full and the next character has been completely received. Bit 0 Receiver Data Ready (DR) This bit is set to a 1 whenever a complete incoming character has been received and transferred into the RX Buffer. The DR bit is reset to a 0 when the host reads the RX Buffer. In the FIFO mode, the DR bit is set when the number of received data bytes in the RX FIFO equals or exceeds the trigger level specified in the FCR0-FCR1. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 131 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) MSR – Modem Status Register (Addr = 6) The Modem Status Register (MSR) reports current state and change information of the modem. Bits 4-7 supply current state and bits 0-3 supply change information. The change bits are set to a 1 whenever a control input from the modem changes state from the last MSR read by the host. Bits 0-3 are reset to 0 when the host reads the MSR or upon reset. Whenever bits 0, 1, 2, or 3 are set to a 1, a Modem Status Interrupt (IIR0-IIR3 = 0) is generated. Bit 7 Data Carrier Detect (DCD) This bit indicates the logic state of the DCH# (RLSD#) output. If Loopback is selected (MCR4 = 1), this bit reflects the state of the Out2 bit in the MCR (MCR3). Bit 6 Ring Indicator (RI) This bit indicates the logic state of the RI# output. If Loopback is selected (MCR4 = 1), this bit reflects the state of the Out1 bit in the MCR (MCR2). Bit 5 Data Set Ready (DSR) This bit indicates the logic state of the DSR# output. If Loopback is selected (MCR4 = 1), this bit reflects the state of the DTR in the MCR (MCR0). Bit 4 Clear to Send (CTS) This bit indicates the logic state of the CTS# output. If Loopback is selected (MCR4 = 1), this bit reflects the state of the RTS bit in the MCR (MCR1). Bit 3 Delta Data Carrier Detect (DDCD) This bit is set to a 1 when the DCD bit changes state since the host last read the MSR. Bit 2 Trailing Edge of Ring Indicator (TERI) This bit is set to a 1 when the RI bit changes from a 1 to a 0 state since the host last read the MSR. Bit 1 Delta Data Set Ready (DDSR) This bit is set to a 1 when the DSR bit has changed since the host last read the MSR. Bit 0 Delta Clear to Send (DCTS) This bit is set to a 1 when the CTS bit has changed since the MSR the host last read the MSR. RBX – RX Buffer (Receiver Buffer Register) (Addr = 0, DLAB = 0) The RX Buffer (RBR) is a read-only register at location 0 (with DLAB = 0). Bit 0 is the least significant bit of the data and is the first bit received. THR – TX Buffer (Transmitter Holding Register) (Addr = 0, DLAB = 0) The TX Buffer (THR) is a write-only register at address 0 when DLAB = 0. Bit 0 is the least significant bit and the first bit sent. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 132 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) SCR – Scratch Register (Addr = 7) The Scratchpad Register is a read-write register at location 7. This register is not used by the modem and can be used by the host for temporary storage. Divisor Registers (Addr = 0 and 1, DLAB = 1) The Divisor Latch LS (least significant byte) and Divisor Latch MS (most significant byte) are two read-write registers at locations 0 and 1 when DLAB = 1, respectively. The baud rate is selected by loading each divisor latch with the appropriate hex value. Programmable values corresponding to the desired baud rate are listed in Table on following page. Divisor Latch (Hex) MS LS 06 00 04 17 03 00 01 80 00 C0 00 60 00 30 00 18 00 0C 00 06 00 04 00 03 00 02 00 01 00 00 Divisor (Decimal) 1536 1047 768 384 192 96 48 24 12 NA Baud Rate 75 110 150 300 600 1200 2400 4800 9600 19200 28800 38400 57600 115600 230400 Programmable Baud Rates Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 133 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Application Notes Tip and Ring Interface Comment [DAR61]: Tip_and_Ring _New_2008.png OEM Motherboard Filtering and Surge Protection Options See Design Considerations and Recommended Parts in Chapter 1. Recommended Uses for Filtering Options • Enhanced Surge Protection with RJ-11 Filtering Use this option when additional lightning protection may be needed. • Alternate Common Mode with RJ-11 Filtering Use this option when your design has common mode emission issues. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 134 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Microphone and Speaker Note: Applies to the MT5692SMI Voice only. Microphone Input Option Comment [DAR62]: Filtering-micoption.png filed under Universal_SocketModem\Graphics\Mi ke_Z_Filtering_Drawings Comment [DAR63]: FilteringSpeaker1.png filed under Universal_SocketModem\Graphics\Mi ke_Z_Filtering_Drawings Speaker Output Option 1 Speaker Output Option 2 Comment [DAR64]: FilteringSpeaker1.png filed under Universal_SocketModem\Graphics\Mi ke_Z_Filtering_Drawings Differences between Speaker 1 Example and Speaker 2 Example Speaker 1 does not have an amplifier while Speaker 2 does. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 135 PART 3 – Embedded Analog SocketModems Chapter 7 – SocketModem (MT5692SMI) Specifications for the Microphone Input Impedance >70K ohms AC Input Voltage Range 1.1V P-P Reference Voltage 1.35V Specifications for the Speaker Output from the Codec Minimum Load 300 Ω Maximum Capacitive Load 0.01 uF Output Impedance 10 Ω AC Output Voltage Range 1.4V P-P Reference voltage +1.35 VDC DC Offset Voltage ± 20 mV Speaker Output The speaker output from the codec is coupled to the speaker pin (64) through a 1uF cap and a 33 ohm resistor. The speaker pin is shared with the call progress monitor which is a digital I/O pin on the DSP that is coupled to the speaker pin through a 1uF and 3.9K. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 136 Comment [DAR65]: This text came from the Conexant Codec data sheet, document CX20437, page 44. Chapter 8 – SocketModem (MT2492SMI) Chapter 8 – SocketModem® (MT2492SMI) Introduction The Multi-Tech SocketModem MT2492SMI-xx utilizes the LSI CVxx Controller Based Modem Devices and the LSI CSP104 Silicon Direct Access Arrangement (DAA) to form a 2-chip complete embedded modem. This solution includes a DSP data pump, modem controller, on-chip RAM and ROM, codec, DAA, analog output, and 24.576 MHz clock input. The modem accepts standard modem AT commands and provides connect rates up to 56 Kbps full-duplex over the Public Switched Telephone Network (PSTN) and features a complete set of modem protocols including all ITU-T standard formats up to V.92. To provide the most flexibility, the CVxx modem system-side device provides numerous additional features for embedded modem applications. It includes call progress monitoring through standard result codes, error correction, data compression, autobaud, and fast connect modes. In addition, because the CVxx modem integrates the DAA, analog features (such as line-in use and over current detection) are included. This device is ideal for embedded modem applications due to its simple host interface, small board space, and low power consumption. Product Build Options and Ordering Information Product Description Region MT2492SMI-92 V.92 Serial Data 5V Regional MT2492SMI-34 V.34 Serial Data 5V Regional MT2492SMI-22 V.22bis Serial Data 5V Regional MT2492SMI-L-92 V.92 Serial Data 3.3V Regional MT2492SMI-L-34 V.34 Serial Data 3.3V Regional MT2492SMI-L-22 V.22bis Serial Data 3.3V Telecom Label Regional MT2492SMI-LS MT2492SMI-Regulatory Label Developer Kit Regional MTSMI-UDK Universal Developer Kit Regional Order this Product How to Read the Product Codes in the Table Above: 92 V.92/56K data rate 34 V.34/33.6K data rate 22 V.22bis data rate 3.3 Volt Build LS Telecom Label UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MT2492SMI-92.Rx. “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product SocketModem (MT2492SMI) Reference Guides Title and Document Product Number SocketModem MT2492SMI AT Commands Reference Guide (S000435x) Fax Commands Voice Commands NA NA Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 137 Chapter 8 – SocketModem (MT2492SMI) Technical Specifications The SocketModem (MT2492SMI) meets the following specifications: Category Description Data Standards V.92, V.90, V.34, V.29, V.22bis, V.22, V.23, V.21; Bell 212A & Bell 103 Data Format Serial, asynchronous Character Format 10 bit Serial/Data Speeds Serial port data rates adjustable to 300, 1200, 2400, 4800, 9600, 19,200, 38,400, 57,600, and 115,200 Client-to-Client Data Rates Data Error Correction 33,600, 31,200, 28,800, 26,400, 24,000, 21,600, 19,200, 16,800 bps 14,400, 12,000, 9600, 7200, 4800 bps 2400, 1200, 0-300 bps V.42 (LAP-M or MNP 2–4) Data Compression V.42bis, MNP 5 Modes of Operation Full duplex over dial-up lines; data mode, command mode, and online command mode Weight 0.6 oz. (0.017 kg.) Operating Temperature 0 to +70° C Storage Temperature -10° to +85° C Humidity 20% to 90% (non-condensing) Operating Voltage Typical: 3.3VDC ± 5%; Absolute Maximum Supply Voltage: 3.6VDC Typical: 5VDC ± 5%; Absolute Maximum Supply Voltage: 5.25VDC Power Measurements 3.3 Volt: Transmit Sensitivity -12 dBm (varies by country) Receiver Sensitivity -40 dBm (-43 dBm under worst case conditions) DAA Isolation 1.5Kv r.m.s. or 2121 VDC at working voltage of 250VAC Flow Control XON/XOFF (software), RTS/CTS (hardware) Typical: 86mA (.283W @ 3.3VDC) Maximum: 96mA (.345W @ 3.6VDC) 5 Volt: Typical: 88.5mA (.442W @ 5VDC) Maximum: 94.8mA (.498W @ 5.25VDC) Note: Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Command Buffer 50 characters Certifications & Approvals Safety Certifications UL/cUL 60950-1 EN 60950-1 AS/NZS 60950:2000 CCC EMC Approvals FCC Part 15 (Class B) Canadian EMC (Class B) EN 55022 (Class B) EN 55024 2 years Warranty Intelligent Features TIA-602 AT command compatible AT command set support Supports V.80 Line polarity reversal detection Line current loss detection Line-in-use detection during on-hook operation Extension pickup detection "Bell Core Type 1" Caller ID Autodial, redial Pulse or tone dial Auto answer Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 138 Chapter 8 – SocketModem (MT2492SMI) SocketModem Pin Out The MT2492SMI SocketModem with a serial interface provides an on-board DAA with tip and ring connections, audio circuit for call-progress monitoring and serial interface via logic level signals. Note: The bolded, shaded pins are active MT2492MI pins. Comment [DAR66]: Pin Out_MT2492SMI.FH9 & .png Top View Serial SocketModem Pin Out For pin descriptions, see the Universal Pin Out Description in Chapter 1. DC Electrical Characteristics 3.3V Serial SocketModem 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33), –RESET (24) Outputs Min 2.0V Output High Max 0.8V Output Low –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) 2mA, Z INT = 120 Ω Digital Input Capacitance Min 2.4V Max 0.4V 50pF 5V Serial SocketModem 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33), –RESET (24) Outputs Min 2.0V Output High Max 0.8V Output Low –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) 2mA, Z INT = 120 Ω Digital Input Capacitance Min 2.4V Max 0.4V Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 50pF 139 Chapter 8 – SocketModem (MT2492SMI) Application Notes Tip and Ring Interface Comment [DAR67]: New Tip and Ring 2008 Comment [DAR68]: Filtering_MT24 92SMI_RJ11-Filtering_b_MikeZ.bmp Comment [DAR69]: Tip_and_Ring rd _3 _section.png Stored under CurrentProj_Universal Guide (for Rev-G. Copied from Tip_and_Ring_New_fromMikeZ_Sch ematic1_Page1_border_removed.FH Will be moved with Rev G material. Comment [DAR70]: Tip_and_Ring _New_2008.png Rev. I OEM Motherboard Filtering and Surge Protection Options See Design Considerations and Recommended Parts in Chapter 1. Recommended Uses for Filtering Options • Enhanced Surge Protection with RJ-11 Filtering Use this option when additional lightning protection may be needed. • Alternate Common Mode with RJ-11 Filtering Use this option when your design has common mode emission issues. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 140 PART 3 – Embedded Analog SocketModems Chapter 9 – SocketModem (MT2456SMI-22) Chapter 9 – SocketModem (MT2456SMI-22) Introduction The Multi-Tech SocketModem supports analog data modem operation with V.22bis Fast Connect, V.42bis data compression, and V.80 synchronous access mode. The SocketModem is a space-efficient (1" × 2.5"), embedded modem that is ready-tointegrate into your applications; therefore, dramatically reducing development time and costs for system designers. The MT2456SMI-22 SocketModem is a standard 20-pin modem used for integrating data communications. It is a single-port 5V or 3.3V modem that integrates a modem controller, DSP, and DAA in a 1" x 2.5" form factor and communicates to a host controller via an asynchronous serial interface. Product Ordering Information Product Description Region MT2456SMI-22 MT2456SMI-L-22 V.22bis Serial Data 5V V.22bis Serial Data 3.3V Telecom Label Global Global MT2456SMI-LS MT2456SMI-Global Regulatory Label Developer Kit Global MTSMI-UDK Universal Developer Kit Global Order this Product How to Read the Product Codes in the Table Above: 22 V.22bis 3.3 Volt Build LS Telecom Label UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MT2456SMI-22.Rx. “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product SocketModem (MT2456SMI-22) Fax Commands Reference Guides Title and Document Product Number MT2456SMI-22 AT Commands Reference Guide NA (S000281x) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Voice Commands NA 141 PART 3 – Embedded Analog SocketModems Chapter 9 – SocketModem (MT2456SMI-22) Technical Specifications The SocketModem (MT2456SMI-22) meets the following specifications: Category Description Data Standards V.22bis, V.22; Bell 212A and 103 Data Format Serial, asynchronous Character Format 10 bit Serial/Data Speeds Serial port data rates adjustable to 300, 1200, 2400, 4800, 9600, 19,200, 38,400, 57,600, and 115,200 Client-to-Client Data Rates 2400, 1200, 0-300 bps Data Error Correction V.42 (LAP-M or MNP 2–4) Data Compression V.42bis Modes of Operation Full duplex over dial-up lines; data mode, command mode, and online command mode Weight 0.6 oz. (0.017 kg.) Operating Temperature 0 to +70° C Storage Temperature -40° to +85° C Humidity 20% to 90% (non-condensing) Operating Voltage Transmit Sensitivity Typical: 3.3 V DC ± 5%; Absolute Maximum Supply Voltage: 3.6 V DC Typical: 5 V DC ± 5%; Absolute Maximum Supply Voltage: 5.5 V DC Source Voltage Maximum Idle Typical 3.3VDC 64mA 59.6mA 62mA 5VDC 68mA 60ma 61mA -12 dBm (varies by country) Power Consumption Receiver Sensitivity -43 dBm DAA Isolation 1.5Kv r.m.s. or 2121 VDC at working voltage of 250VAC Flow Control XON/XOFF (software), RTS/CTS (hardware) Command Buffer 50 characters Warranty 2 years Intelligent Features AT command compatible V.22bis fast connect Supports V.80 Supports Fast POS 9600 Line polarity reversal detection Line current loss detection Line-in-use detection Extension pickup detection Remote hang-up detection Call waiting detection "Bell Core Type 1" Caller ID Autodial, redial Pulse or tone dial Auto answer Call status display Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 142 PART 3 – Embedded Analog SocketModems Chapter 9 – SocketModem (MT2456SMI-22) SocketModem Configuration Serial Configuration The MT2456SMI-22 SocketModem with a serial interface uses a 20-pin interface to provide an on-board DAA with tip and ring connections, audio circuit for call-progress monitoring and serial interface via logic level signals. Note: The bolded, shaded pins are active MT2456SMI-22 pins. Top View Comment [DAR71]: 2456SMI.png Serial SocketModem Pinout For pin descriptions, see the Universal Pinout Descriptions in Chapter 1. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 143 PART 3 – Embedded Analog SocketModems Chapter 9 – SocketModem (MT2456SMI-22) Electrical Characteristics 3.3V Serial SocketModem 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33), –RESET (24) Min 2.0V Max 0.8V Outputs Output High Output Low –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) 2mA, Z INT = 120 Ω Min 2.4V Max 0.4V Digital Input Capacitance 50pF 5V Serial SocketModem 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33), –RESET (24) Min 2.0V Max 0.8V Outputs Output High Output Low –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) 2mA, Z INT = 120 Ω Min 2.4V Max 0.4V Digital Input Capacitance Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 50pF 144 PART 3 – Embedded Analog SocketModems Chapter 9 – SocketModem (MT2456SMI-22) Applications Notes Tip and Ring Interface Comment [DAR72]: Tip_and_Ring _New_2008.png Rev. I OEM Motherboard Filtering and Surge Protection Options See Design Considerations and Recommended Parts in Chapter 1. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 145 PART 4 – Embedded Device Servers Part 4 Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 146 PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) Chapter 10 – SocketEthernet IP® (MT100SEM-IP) Introduction The SocketEthernet IP® (MT100SEM-IP) device server connects serial devices to an IP network for remote monitoring, control and configuration. The space efficient communications device (1” x 2.5”) integrates Multi-Tech's Universal IP™ protocol stack and a serial-to-Ethernet interface into a single, universal socket design. The SocketEthernet IP can make your existing and next generation device, machine or system, IP-ready while you focus on developing its core features. Product Build Options and Ordering Information Product Description Region Order this Product MT100SEM-IP Embedded Serial-to-Ethernet Device Server with Universal IP™ – 5V Global MT100SEM-L-IP Embedded Serial-to-Ethernet Device Server with Universal IP™ – 3.3V Global MT100SEM-IP MT100SEM-L-HV-IP Embedded Serial-to-Ethernet Device Server with High Voltage Dielectric Isolation (EN60601) and Universal IP™ – 5V Developer Kit Global MTSMI-UDK Global Universal Developer Kit How to Read the Product Codes in the Table Above: IP Universal IP™ Stack 3.3 Volt HV High Voltage Dielectric Isolation (EN60601) UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MT100SEM-L-IP.Rx “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product Serial-to-Serial Device Server (MT100SEM-IP) Reference Guides Title and Document Product Number Multi-Tech Universal IP AT Commands (S000426x) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Fax Commands Voice Commands NA NA 147 PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) Technical Specifications The SocketEthernet IP (MT100SEM-IP) meets the following specifications: Category Description Interfaces 10/100BaseT Ethernet, Asynchronous Serial Serial Character Format 8N1 (Data, Parity, and Stop bits are configurable) Serial/Data Speeds 300 to 921600 bps Ethernet Data Speeds 10MB or 100MB Physical Description 2.541" L × 1.045" W × 0.680" H; 0.6 oz. (6.45 cm × 2.65 cm × 1.7 cm; 0.017 kg.) Comment [DAR73]: From Dustin 6/24/09 Operating Temperature 0° to +70° C Storage Temperature -40° C to +85° C Humidity 20% to 90% (non-condensing) Operating Voltage 5VDC or 3.3VDC Power Measurements See the Power Measurements table. Flow Control RTS/CTS (hardware) Network Protocols Supported ARP, DHCP client, DNS client, FTP, ICMP (ping), IP, POP3, SMTP, TCP, Telnet server, UDP Management Serial Telnet Web-based configuration Certifications & Approvals Safety Certifications UL 60950 cUL 60950 EN 60950 AS/NZS 60950:2000 Safety Certifications for High Voltage Build UL 60601-1 EN 60601-1 EMC Approvals FCC Part 15 Class B Canada Class B EN 55022 Class B EN 55024 Warranty 2 years Intelligent Features Complete serial-to-Ethernet connectivity solution including network processor, media access controller and physical interface. AT Command compatible LED driver outputs for visual monitoring speed, link, activity, collision and duplex mode Half duplex or full duplex support on the LAN interface Central site setup and control of the remote communications device. Flash memory to update firmware with the latest enhancements Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 148 PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) SocketEthernet IP Pin Out The SocketEthernet IP uses a 22-pin interface to provide an on-board Ethernet media access controller, an Ethernet physical layer (without the RJ-45 jack), an LED driver for Ethernet monitoring, and a serial interface. Note: The shaded, bolded pins are SocketEthernet IP active pins. Top View SocketEthernet IP MT100SEM-IP Pin Out Comment [DAR74]: M100SEM.png For pin descriptions, see the Universal Pin Out Descriptions in Chapter 1. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 149 PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) DC Electrical Characteristics 3.3V Serial 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Parameter Input Low Level –DTR (40), –TXD (35), –RTS (33), –RESET (24) Note: These inputs are 5 volt tolerant Minimum -0.3V Maximum 0.8V Input High Level –DTR (40), –TXD (35), –RTS (33), –RESET (24) Note: These inputs are 5 volt tolerant Min 2.52V VDD Output Low Level –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) NA 0.4V Current Drive 2mA Output High Level –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Min. 2.3V NA Current Drive 2mA Minimum -0.3V Maximum 0.8V Input High Level –DTR (40), –TXD (35), –RTS (33), –RESET (24) 2.52V VDD Output Low Level –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) NA 0.4V Current Drive 2mA Output High Level –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) 2.3V NA Current Drive 2mA Digital Input Capacitance – 5 pF 5V Serial 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Parameter Input Low Level –DTR (40), –TXD (35), –RTS (33), –RESET (24) Digital Input Capacitance – 5 pF Power* Measurements MT100SEM-IP Measured Power at Input Voltage 5.00 Sleep Typical Maximum Current (AMPS) 0.187 0.187 0.194 Watts 0.935 0.935 .97 MT100SEM-IP Measured Power at Input Voltage 3.3 Sleep Typical Maximum Current (AMPS) NA 0.137 0.168 Watts NA 0.411 0.504 * Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 150 PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) Application Notes Ethernet Interface – Non-Isolated Design Comment [DAR75]: MT100SEM IP Non Isolated Scan0578_000.jgp 97KB jpg was smaller than png. Filed under CurrentProj_Universal_Guide_2009_ Rev_J\Graphics Note: VREF stands for Power in this drawing. Comment [DAR76]: MT100SEM IP Isolated Scan0579_000.jpg (jpg was smaller than png) 169KB. Filed under CurrentProj_Universal_Guide_2009_ Rev_J\Graphics Ethernet Interface – Isolated Design Isolated Design Application Note The MT100SEM-L-HV-IP was designed to meet Basic Isolation at 240Vac according to the international medical directive for safety (EN60601-1). The recommended components for an isolated design comply with the same standard. Recommended Parts Recommended Capacitors for a Non-Isolated Design: Manufacturer – NIC Components Corp. Part Number – NMC0603NPO150J50TRPF Recommended Safety Rated Capacitors for an Isolated Design: The recommended capacitors are Y2 rated and meet supplementary isolation at 240Vac along with the required creepages and clearances. Manufacture – NOVACAP Part Number – ES2211N(value)K502NXT Recommended Resistor: The resistors are 75 ohms 1/8 watt. Recommended Ethernet Modular Jack: The recommended jack is an eight contact, eight position, unshielded and ungrounded connector that will maintain the need isolation and spacing requirements. A shielded and grounded connector may be used, but special consideration must be made for the isolation and spacing requirements. Manufacture – Stewart Connector Systems Part Number – SS-6488-NF-K1 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 151 PART 4 – Embedded Device Servers Note: These SocketEthernet parts are RoHS compliant. Chapter 10 – SocketEthernet IP (MT100SEM-IP) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 152 PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) The Windows-Based Auto-Discovery Manager The Auto-Discovery Manager is a mechanism for remotely monitoring the Universal IP functioning. It also provides support for configuring several key parameters, such as DHCP Status (enable/disable), IP Address, and the Host Name of an MT100SEM-IP. The Auto-Discovery mechanism is utilized by running a Windows-based Server Application that can monitor/configure the MT100SEM-IP. Communication between the MT100SEM-IP and the Windows-based Server is through MAC level broadcasts on a configured UDP port. Two Ways to Use Auto Discovery: Auto-Discovery can be performed by using AT Commands (see the Universal IP AT Commands Reference Guide – included on the Universal Kit CD) or by using the Auto-Discover Manager Software (also included on the Universal Kit CD). Auto-Discovery Manager Software The Auto-Discovery Manager is composed of two components: • The Client Component – The Client component periodically broadcasts its current configuration over the network. • The Server Component – The Server component receives the broadcasts from the client. Client Component The Auto-Discovery Client component is integrated with MT100SEM-IP. It broadcasts its current configuration over the network on a specific UDP SERVER-PORT. By default the SERVER-PORT is set to 1020. The configuration parameters broadcast are • • • • • • • • Version details MAC Address Static IP Address DHCP Status DHCP Assigned IP Address Host Name Broadcast interval Port number on which the client listens Server Component The Server component listens on the SERVER-PORT. It receives the broadcasts from the client and updates the list of configuration parameters. This list can be viewed by the administrator through the User Interface: The List of Entries Detailed Information about a Selected Entry Log Files will display here Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 153 Comment [DAR77]: Auto Discovery Screen1.jpg (jpg was smaller than png) 184KB. CurrentProj_Universal_Guide_2009_ Rev_J\Graphics\Auto Discovery for Universal PART 4 – Embedded Device Servers Chapter 10 – SocketEthernet IP (MT100SEM-IP) How to View the Detailed Information New entries are appended to the list shown on the screen above. Only the first ten entries are displayed on the screen. However the administrator can scroll down to view more entries. Clicking on an entry displays the detailed information about that entry. How to Edit the List and Make the Changes Permanent 1. Double-click on the entry you wish to edit. 2. After clicking the desired entry, a new dialog box displays showing the current configuration. 3. Comment [DAR78]: Auto Discovery Screen2.png 12KB. CurrentProj_Universal_Guide_2009_ Rev_J\Graphics\Auto Discovery for Universal Enter the new parameters and click the SET button. The server sends the modified parameters to the client. Upon receiving the broadcast from the Server, the Client validates the packet. The Client determines whether the packet is destined for its own MAC Address. If so, it sets the modified parameters that are different from its current configuration, and the it broadcast the newly configured parameters. The Client Status is set to Active upon the receipt of a broadcast packet. The Client Status is made Inactive if there is no request from the client for a stipulated period. (3 * periodic timer value). How to Set the Parameters to the Previous Configuration When the RESET button is clicked, the parameters are set to the defaults received. In other words, RESET is similar to UNDO (it sets the modifications to the previous ones). Saving the Log The logs can be saved to a file. They are spooled into the third part of the window in the main dialog box. To save the log: Select File > Save Log As. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 154 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Chapter 11 – SocketWireless® Wi-Fi® (MT810SWM-IP) Introduction The SocketWireless® Wi-Fi® device server connects serial devices to an IP network via 802.11b/g wireless networking. It enables you to build wireless networking into virtually any device allowing for remote monitoring, control and configuration. The space efficient communications device (1” x 2.5”) integrates a complete TCP/IP protocol stack. It can make your existing and next generation device, machine or system, IP-ready while you focus on developing its core features. Product Build Options and Ordering Information Product Description Region MT810SWM-IP 802.11b/g Wi-Fi Device Server with IP, 5V Regional MT810SWM-L-IP 802.11b/g Wi-Fi Device Server with IP, 3.3V Regional MTSMI-UDK Developer Kit Universal Developer Kit Regional Order this Product How to Read the Product Codes in the Table Above: IP TCP/IP Stack 3.3V UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MT810SWM-IP.Rx “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Multi-Tech Systems, Inc. provides documentation of AT Commands for each embedded module. These AT Command Reference Guides are available on the CD included in the Developer Kit and are also available by request. Send an email to oemsales@multitech.com to request the copy you desire. Product SocketWireless Wi-Fi Device Server (MT810SWM-IP) Reference Guides Title and Document Product Number Multi-Tech's Universal IP AT Command Reference Guide (S000426x) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Fax Commands NA Voice Commands NA 155 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Technical Specifications The SocketWireless Wi-Fi meets the following specifications: Category Description Wireless Specifications WLAN Standard Frequency Range Data Rate Maximum Transmit Power Receiver Sensitivity Security Mode Antenna Connector IEEE 802.11b/g Wi-Fi 2.400 to 2.484 GHz 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 & 54Mbps 15 dBm -82 dBm (with PER < 8%) 64/128 bit WEP, WPA-PSK, WPA2, WPA2-PSK Ad Hoc, Infrastructure UFL Serial Interface Data Format Data Rate Data Bits Parity Flow Control Serial, asynchronous Software selectable: 1200 bps to 921.6K bps 7 or 8 data bits, 0 or 1 stop bits Odd, even, none RTS/CTS (Hardware), None Network Protocol Support Protocols Supported ARP, DHCP Client, DNS Client, FTP Client, ICMP (PING), IP, POP3 Client, SMTP Client, TCP Client & Server, UDP Client & Server Comment [DAR79]: Updated list by Dustin for Rev. K Power Requirements* Supply Voltage Power Usage 3.3VDC or 5VDC Typical – 400mA @ 3.3VDC, 240mA @ 5VDC Environmental Operating Temperature Storage Temperature Humidity -30° to +70° C -40° to +85° C 20% to 90% (non-condensing) Physical Description Dimensions Weight 2.541" L x 1.045" W x 0.680" H (6.45 cm x 2.65 cm x 1.7 cm) 0.6 oz. (0.017 kg.) Certifications, Approvals, Warranty Certifications Warranty Safety Certifications UL 60950-1 cUL 60950-1 IEC 60950-1 EMC Certifications FCC Part 15 Subpart C Canada RSS-210 EN 300 328 EN 301 489-17 Two years Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 156 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Technical Specifications Continued Intelligent Features Features Command line configuration through serial interface AT Command compatible System firmware upgraded through serial port. Over the air firmware upgrade Command line configuration through TELNET Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 157 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Comment [DAR80]: Vault Data 363 -- 9/2/09 Mechanical Drawings Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 158 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Comment [DAR81]: Vault Data 363 -- 9/2/09 Mechanical Drawings Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 159 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 160 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Operating Conditions In Volts Parameter Supply Range - Vcc Minimum Maximum 3.3V = 3.15 3.3V = 3.45 5V = 4.75 5V = 5.25 Absolute Maximum Rating Parameter Voltage at any signal pin Minimum Maximum GND - 0.3V Vcc + 0.3V DC Electrical Characteristics For 5V and 3.3V Units (Volts) Parameter Digital Signal Input Low Level Minimum Maximum GND 0.8V Digital Signal Input High Level 2.0V Vcc Digital Signal Output Low Level NA 0.4V Digital Signal Output High Level 2.4V NA Reset (Low Active) Input Low GND 0.8V Reset (Low Active) Input High 2.0V Vcc Digital Input Capacitance 5pf Power Measurements* MT810SWM-IP Measured Power at Input Voltage: 3.3 Volts Idle Typical Maximum Current (AMPS) 0.057 0.180 0.260 Watts 0.182 0.531 0.764 Comment [DAR82]: The voltages came from Tom Fix on Sept 25, 2009. I put in the guide on 10/16/09. MT810SWM-IP Measured Power at Input Voltage: 5.00 Volts Idle Typical Maximum Current (AMPS) 0.056 0.193 0.260 Watts 0.274 0.897 1.196 * Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 161 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Application Notes RF Interface Radio Characteristics Frequency Modulation Number of Channels Transmission Rate RF Receive Sensitivity RF Transmit Power 2402 – 2480MHz DSSS 1 to 14 1, 2, 5.5, 11, 12, 18, 24, 36, 48, 54 Mbps -82dBm typical 15 dBm Default Power Up Settings Baud Rate = 115200 bps Data Bits = 8 bits Parity = None Stop bits = 1 bit Hardware Flow Control RTS/CTS = Disabled Antenna Requirements and Sources Frequency Range Impedance VSWR Gain Radiation Polarization Connector ROHS Compliant 2.4 - 2.5 GHz 50 ohm nominal <2.0:1 5 dBi Omni Vertical Reverse Polarity SMA Plug YES Antenna Source for Wi-Fi The antenna can be ordered from the following manufacturer: Aristotle Enterprises http://www.aristotle.com.tw/ Part Number Description RFA-02-5-F7M3 2.4 GHz 5dBi Swi-Reverse-F Antenna Antenna Cable and Connector See Chapter 1 for Antenna System details. Note that the cable for the Wi-Fi SocketModem has a reverse polarity SMA plug. Approved Antenna Cable Parts GC Protronics 20930C Samtec ASP-116785-01 Coax Cable RG-178/U Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 162 Part 4 – Embedded Device Servers Chapter 11 – SocketWireless Wi-Fi (MT810SWM-IP) Regulatory Requirements for the Wi-Fi Antenna This section covers how to use the modular transmitter in order to maintain the modular transmitter approval and RF exposure compliance. Conditions to Satisfy Modular Transmitter Approval This device is intended only for use by OEM integrators under the following 3 conditions: 1. The antenna must be installed such that 20 cm is maintained between the antenna and the end user for all installations. 2. The transmitter module may not be located with any other transmitter or antenna. 3. The communications device is approved using the FCC "unlicensed modular transmitter approval" method. Therefore, the communication device must only be used with the originally approved antennas. As long as the 3 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this communication device installed (for example, digital device emissions, PC peripheral requirements, etc.) IMPORTANT NOTE: In the event that any of these conditions CANNOT be met (for example certain laptop configurations, location with another transmitter, or use of a different type antenna), then the FCC authorization for the communications device is no longer considered valid and the FCC ID CANNOT be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. RF Exposure Statements Developers Must Include in the User Manual for End Users The user manual for consumers must include the following information in a prominent location: IMPORTANT NOTE: To comply with FCC RF safety exposure limits, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Regulatory Requirements for End Product Labeling Suggested End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed in such a way that 20 cm may be maintained between the antenna and the users (for example access points, routers, wireless ASDL modems, and similar equipment). The final end product must be labeled in a visible area on the exterior of the enclosure with the following or similar text: "Contains TX FCC ID: AU792U07B06821". FCC & IC Information to Consumers The user manual for the consumer must contain the statements required by the following FCC and IC regulations: 47 C.F.R. 15.19(a)(3), 15.21, 15.101 and RSS-Gen Issue 2 dated June 2007, Sections 7.1.4 and 7.1.5. Additional Information That Must Be Provided to OEM Integrators The end user should NOT be provided any instructions on how to remove or install the modular transmitter. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 163 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Chapter 12 – SocketWireless® Bluetooth® (MTS2BTSMI) Introduction The Multi-Tech Systems, Inc. SocketWireless® with Bluetooth®-enabled technology allows developers to establish wireless networks using a special set of AT commands. The SocketWireless with Bluetooth technology makes the cable-replacement transition to wireless networks seamless and easy. This chapter explains how to establish Bluetooth communication between two serial devices for data applications in a point-topoint network. Bluetooth-enabled devices create communication-ready devices by integrating data functionality into a single, universal socket design. This complete, ready-to-integrate device dramatically reduces development time and costs for system designers. Notes about Byte Gaps and Data Latency Because of the way Bluetooth is designed and operates, random byte gaps of 5 ms to 20 ms are common. Packet size will vary from transmission to transmission. Although the serial band frequency operates up to 920K bps, effective data throughput in fast streaming mode is approximately 200K bps. Effective data throughput in regular data mode is 60K bps. The reason for the slower speed in regular mode is due to the AT parser, which looks at each character for ASCII valid command scripts in the regular mode's data stream. The SocketWireless RX has very limited buffering, so if you do not use hardware flow control and are transmitting further distances, you will quickly overflow the 50 byte buffer because of RF retransmissions, etc. When a Bluetooth connection is made, the SocketWireless device goes into regular data mode per the power-up factory default settings. This enables the user to configure the SocketWireless settings remotely via a remote RF Bluetooth connection. Basically, you can setup the SocketWireless device so no commands are required to be sent from the embedded side of the device. This allows seamless interfacing with legacy systems without the need to modify the host device Product Build Options and Ordering Information Product Description Region MTS2BTSMI MTS2BTSMI-L Embedded Serial-to-Bluetooth, C1, 5V Embedded Serial-to-Bluetooth, C1, 3.3V Developer Kit Universal Developer Kit Global Global MTSMI-UDK Order this Product Global How to Read the Product Codes in the Table Above: C1 Class 1 Bluetooth 3.3V UDK Universal Developer Kit Other Product Codes: The complete product code may end in .Rx. For example, MTS2BTSMI-L.R2. “R” indicates product revision. “x” is the revision number. AT Commands Reference Guide Product SocketWireless Bluetooth (MTS2BTSMI) Reference Guides Title and Document Product Number SocketWireless Bluetooth AT Commands Reference Guide (S000360x) Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) Fax Commands Voice Commands NA NA 164 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Technical Specifications The SocketWireless Bluetooth (MTS2BTSMI) meets the following specifications: Category Standard Frequency Range Data Format Serial Speeds Flow Control Output Level (Class 1) Modes of Operation Device Profiles Buffer Weight Power Measurements Operating Temperature Storage Temperature Humidity Operating Voltage Certifications & Approvals Intelligent Features Warranty Description Class 1 Bluetooth V2.0 compliant Note: For Bluetooth protocol V2.0, the circuit board I/O pin 7 now controls flow control. In V1.2, circuit board I/O pin 3 controlled flow control. V2.0 now supports multipoint connections. 2402 to 2480 MHz (2.402 to 2.480 GHz) For Serial Interface - Asynchronous Supports speeds from 1200 bps to 920K bps Hardware 20dBm maximum Inquiry, Idle, Data, Fast Data, Park, Sniff, Command, Master, Slave Serial Port (SPP), Dial-up Network (DUN) Serial 50 bytes RF 50-byte RX buffer 0.6 oz. (0.017 kg.) Idle: 1.5mA @ 3.3VDC 1.6mA @ 5VDC Master Connected: 6mA @ 3.3VDC 7mA @ 5VDC Fast Data: 21mA @ 3.3VDC 38mA @ 5VDC Master Inquiry: 68mA @ 3.3VDC 74mA @ 5VDC Notes: These power measurements were taken with no LEDs connected. Driving an LED through 330 ohm resistor to GND draws an additional 4mA on 5V for each LED. Note: Multi-Tech Systems, Inc. recommends that the customer incorporate a 10% buffer into their power source when determining product load. -40° to +70° C -40° to +85° C 20% to 90% (non-condensing) 5VDC or 3.3VDC Minimum and Maximum Voltage: 3.3VDC ± 0.1V & < 10mVp-p noise 5VDC ± 0.1V & < 10mVp-p noise Safety Certifications: UL 60950 cUL 60950 EN 60950 AS/NZS 60950:2000 EMC Approvals: FCC Part 15.247:2004 (subpart C) EN 301 489-1 V1.4.1 (2002-08) Can be configured, commanded, and controlled through simple ASCII strings over the Bluetooth RF link or directly through the hardware serial UART. Low power consumption. Secure and robust communication link. • FHSS (Frequent Hopping Spread Spectrum) • 56-bit encryption, and 10 alphanumeric Personal Identification Number (PIN) • Error correction schemes for guaranteed packet delivery Operating System independent AT command software interface LED driver outputs for visual monitoring speed, link, activity, collision, and duplex mode. Auto connect. Supports multipoint connections. Two years Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 165 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Comment [DAR83]: New one: 20501d1_BT_Mechanicaldimensions. gif Old one: 205001d1_mechanicalDimensions.b mp SocketWireless Bluetooth Pin Out Note: The bolded, shaded pins are the active SocketWireless pins. Top View – SocketWireless Bluetooth Pin Out For pin descriptions, see the Universal Pin Out Descriptions in Chapter 1. DC Electrical Characteristics 5V Serial SocketWireless 5VDC Characteristics (VDD = 5V ± 0.25V) VDDMAX = 5.25V Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33) Min 2.0V Max 0.8V –RESET (24) Min 2.0V Max 0.8V Outputs Output High Output Low Current Drive –DCD (39), –CTS (38), –RI (36), –RXD (34) Min 4V / 2.4V Max 0.5V / 0.5V (5V / 3.3V) 3.2mA, 7.0mA for TXD Input Capacitance 15 pF 3.3V Serial SocketWireless 3.3VDC Characteristics (VDD = 3.3V ± 0.3V) VDDMAX = 3.6V Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33) Min 2.0V Max 0.8V –RESET (24) Min 2.0V Max 0.8V Outputs Output High Output Low Current Drive –DCD (39), –CTS (38), –RI (36), –RXD (34) Min 2.4V Max 0.5V / 0.5V (5V / 3.3V) 3.2mA, 7.0mA for TXD Input Capacitance 15 pF Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 166 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Application Notes RF Interface Radio Characteristics Frequency Modulation Channel Intervals Number of Channels Transmission Rate RF Receive Sensitivity RF Range 2402 – 2480MHz FHSS/GFSK 1MHz 79CH 721Kbps -80dBm typical Class 1 - 100 meters (330 feet) Sources for Peripheral Devices Antenna Requirements 2.4-2.5 GHz 50 ohm nominal <2.0:1 2 dBi Omni Vertical Dipole ½ Wave Reverse Polarity SMA Plug Frequency Range Impedance VSWR Gain Radiation Polarization Wave Connector Antenna Source Bluetooth Antenna Available from Multi-Tech: Part Number Description ANBT-1HRA Hinged Right Angle 2.5 GHz ½ Wave Reverse Polarity Antenna Bluetooth antennas also can be ordered from the following manufacturers. For the manufacturers listed without specific part numbers, be sure to select the antenna that meets the requirements listed above. http://nearson.com (part number S131AH-2450S) http://www.ead-ltd.com http://www.centurion.com http://www.mobilemark.com http://woken.com Antenna Cable and Connector See Chapter 1 for Antenna System details. Note that the cable for the Wi-Fi SocketModem has a reverse polarity SMA plug. Approved Antenna Cable Parts GC Protronics Samtec Coax Cable 20930C ASP-116785-01 RG-178/U Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 167 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Default Power Up Settings AT Command Response Form = Long Form Bluetooth Service Profile = Serial Port Profile {SPP} Device Role = Slave Baud Rate = 9600bps Data Bits = 8 bits Parity = None Stop bits = 1 bit Hardware Flow Control RTS/CTS = Enabled Power Mode = Never go into deep sleep mode Country Code = North America and Europe Name of Device (local name) = SocketWireless My Radio Status = 1,0 {slave, disconnected} Service Name = COM0 Power up default ATSW24 settings = 0,0,0,0 {long response, no authentication, no auto SCO connect, no minor} Power up default ATSW25 settings = 0,1,0,0 {slave, data, allow data to pass, SPP} Major & Minor Class Of Device (COD) = 00000000 {undefined} Security PIN and Encryption Disabled Default PIN = “default” caps sensitive so do not use any capital letters Important Security PIN Note: Do not forget your PIN. Write it down. If you forget it, there is no way it can be retrieved from the device or the software. You will have to buy a new SocketWireless Bluetooth and start over. Page Scan Interval = 0x400 {2560msec.} Page Scan Window = 0x200 {11msec.} Inquiry Scan Interval = 0x400 {2560msec.} Inquiry Scan Window = 0x200 {11msec.} Timeout Connection Parameters Inquiry = 60 seconds Slave Connect = 60 seconds Master Connect = 60 seconds ATDM idle mode = 60 seconds ATDM Master Mode = indefinitely (need to perform ATUCL to cancel last command) Timeout for loss of Bluetooth connection = 4 seconds Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 168 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Example of a Master Discovery/Connection Sequence From Power Up and No Connection 1. Verify local device is Master in Data Mode. Sent: ATSi,7 Reply: 1,1,0,0 2. If not Master, set to Master and Data Mode. Sent: ATSW25,1,1,0,0 Reply: OK 3. Perform an Inquiry to obtain BT Address (unless it is already known). Sent: ATUCL // Clears radio state and places in Idle Mode Reply: OK Sent: ATDI,1,00000000 {Class of Device} // Looks for only one Bluetooth device Reply: 00A0961F2023,00000104,Socket Wireless DONE 4. Perform a Master Connect over SPP using the BT Address. Sent: ATDM, 00A0961F2023,1101 // SPP connection Reply: CONNECT,00A0961F008F // Returns Slave BT address radios is in Data Mode 5. Place radio into Fast Data Mode. Sent: ATMF Reply: OK 6. // Places radio in Fast Data Mode Send Data. Note: When sending commands from the Slave when the Slave connects in Fast Data Mode (ATSW25/or issuing ATMF). All valid AT commands are sent through the Slaves UART will be interpreted and responded by the Master radio as if it was the local Slave radio. Basically in this configuration from the Slave end you can obtain status and configure from the remote Master radio. This is a unique feature that may be useful in some applications but can confuse the user if you think you are talking to the local Slave UART. To Get Out of Data Mode and Check Status: 1. Delay at least 50 milliseconds; this could be less or more. 2. Get into Command Mode. Sent: +++ Reply: OK 3. Check Status Sent: AT Reply: OK 4. Or send any AT Command example: Sent: ATSI,0 Reply: SocketWireless AT // Default escape sequence of characters Example of a Slave Command Sequence From Power Up: 1. Check and verify Communication to Slave. Sent: AT Reply: OK 2. Get information on Slave Bluetooth address. Sent: ATSi,1 Reply: 12-digit address OK 3. Set Slave to automatically connect in Fast Data Mode on Bluetooth connection. Sent: ATSW25,0,0,0,0 Reply: OK 4. Either cycle power or send ATURST. Note: This command sequence assumes the radio is in factory default in which it automatically comes up and is connectable as a Slave from a Master request. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 169 PART 4 – Embedded Device Servers Chapter 12 – SocketWireless Bluetooth (MTS2BTSMI) Disabling Flow Control Using AT Commands Protocol Change: For Bluetooth protocol V2.0, the circuit board I/O pin 7 now controls flow control. Previous Protocol V1.2 New Protocol V2.0 ATSW22,3,x,x ATSW22,7,x,x ATSW23,3,x,x ATSW23,7,x,x Disabling Flow Control Using Protocol V.2.0 Using a terminal screen with flow control enabled, issue commands to turn off flow control. Sent: ATSW22,7,1,0 // Set PIO7 as output and do not store in flash Reply: OK Sent: ATSW23,7,1,0 // Set PIO7 output high and do not store in flash Reply: OK To store the setting in flash: Sent: ATSW22,7,1,1 // Set PIO7 as output and store in flash Reply: OK Sent: ATSW23,7,1,1 // Set PIO7 output high and store in flash Reply: OK Now you can communicate with the Bluetooth device with flow control turned off. Other Examples See the Bluetooth AT Commands Reference Guide for other examples: • Multipoint Example Using the SocketWireless MTS2BTSMI or the Bluetooth Adapter MT2BTA – One Slave and Four Master Devices. • Multipoint Example Using the SocketWireless MTS2BTSMI or the Bluetooth Adapter MT2BTA – One Master and Four Slave Devices. • Repeater Example Using the SocketWireless MTS2BTSMI or the Bluetooth Adapter MT2BTA. Changing Configuration Parameters, such as the Bluetooth Name, Service Name, Class of Device, and Serial Port settings can be viewed and configured. This can be done locally through the serial port UART or from a remote Bluetooth RF link. To configure the SocketWireless Bluetooth device, the device must be in command mode by issuing +++. You can use the developer board and the RS-232 cable to connect to a PC and pass ASCII characters through the terminal to the SocketWireless Bluetooth device. The communications settings should match the settings used when the SocketWireless Bluetooth device connects. For example, the defaults are: 9600bps 8 bits No Parity 1 stop bit Hardware flow control enabled. Once you change these parameters, you have the option to store them permanently in the non-volatile memory. Run your favorite terminal emulator, HyperTerminal, or other program. • Type AT on your screen and follow it with a carriage return . You should see "OK" returned to you. This will verify that your cable and communications settings are correct. When the SocketWireless device is not connected to another Bluetooth device, you can type the AT commands directly into the SocketWireless' UART; e.g., you do not have to type +++ to change from data mode to command mode. • Now you can enter any of the AT commands discussed in the following sections. Follow these commands by . Valid commands will return an "OK" or a valid response. Invalid commands will reply ERROR. • To return to data mode, type ATMD. You can now pass or receive data from a remote connected Bluetooth device. Notes: • If you change communications parameter settings, remember to change your terminal or emulator communications settings to correspond to the newly created parameter settings. • AT commands will not echo back to the terminal. Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 170 Index Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 171 Index Index Activation procedures .......................................................37 Antenna system.................................................................34 AT Commands Reference Guides SocketEthernet IP (MT100SEM-IP) ...........................147 SocketModem (MT2456SMI-22) ...............................141 SocketModem (MT2492SMI).....................................137 SocketModem (MT5692SMI).....................................116 SocketModem (MT9234SMI).....................................100 SocketModem CDMA (MTSMC-C) ............................67 SocketModem Cell & iCell (MTSMC-G2 Family) ......56 SocketModem EDGE (MTSMC-E and E1)..................76 SocketModem HSDPA (MTSMC-H) ...........................84 SocketWireless Bluetooth (MTS2BTSMI) .................164 SocketWireless Wi-Fi (MT810SWM-IP) ...................155 Auto-Discovery Manager ...............................................153 Baud Rate Dip Switch Settings for HDSPA .....................94 Block Diagram..................................................................23 Bluetooth Changing Configurations ...............................170 Bluetooth Example of a Master Discovery/Connection Sequence.....................................................................169 Bluetooth Example of a Slave Command Sequence .......169 Bluetooth technology......................................................164 Board Components ...........................................................22 CDMA Terminology 2G .................................................................................74 3G .................................................................................74 CBM .............................................................................74 CDMA ..........................................................................74 cdma2000......................................................................74 cdma2000 1xRTT .........................................................74 cdmaONE .....................................................................74 ESN...............................................................................74 Handset Path .................................................................74 Headset Path .................................................................74 IMSI..............................................................................74 IOTA.............................................................................74 IS-2000 .........................................................................74 IS-707 ...........................................................................74 IS-95 .............................................................................74 IS-95A ..........................................................................74 IS-95B...........................................................................74 MCC .............................................................................74 MDN.............................................................................74 MIN ..............................................................................74 MNC .............................................................................74 MO................................................................................74 MS ................................................................................74 MSM.............................................................................74 MT ................................................................................74 NAM ............................................................................ 74 NID .............................................................................. 74 NV-RAM ..................................................................... 75 OTAPA ........................................................................ 75 OTASP ......................................................................... 75 PDU.............................................................................. 75 PN Offset...................................................................... 75 P-REV .......................................................................... 75 PRI ............................................................................... 75 PRL .............................................................................. 75 PSTN............................................................................ 75 RF................................................................................. 75 RSSI ............................................................................. 75 R-UIM.......................................................................... 75 SID ............................................................................... 75 SIM .............................................................................. 75 SMS.............................................................................. 75 TA/TE .......................................................................... 75 Changing the Quad Band ................................................. 65 China’s Administrative Measures on the Control of Pollution ....................................................................... 54 Connectivity Features....................................................... 10 Country/Regional Codes .................................................. 45 DC Electrical Characteristics SocketEthernet IP (MT100SEM-IP) .......................... 150 SocketModem (MT2492SMI) .................................... 139 SocketModem (MT5692SMI) .................................... 121 SocketModem (MT9234SMI) .................................... 105 SocketModem CDMA (MTSMC-C) ....................... 71 SocketModem Cell & iCell (MTSMC-G2 Family) ...... 58 SocketModem EDGE (MTSMC-E1) ........................... 82 SocketModem HSDPA (MTSMC-H) .......................... 90 SocketWireless Bluetooth (MTS2BTSMI)................. 166 Default Power Up Settings for Bluetooth....................... 168 Default Power Up Settings for MT810SWM-IP ............ 162 Design Considerations...................................................... 16 Developer Board .............................................................. 21 Developer Board Schematics ......................... 24, 26, 27, 28 Electrical Characteristics SocketModem (MT2456SMI-22)............................... 144 Electromagnetic Interference Considerations................... 17 Electrostatic Discharge Control........................................ 17 EMC Requirements for Industry Canada ......................... 46 EMC, Safety, and R&TTE Directive Compliance ........... 46 Fax Commands Reference Guides ................................... 11 FCC Part 15 Regulation ................................................... 46 FCC Part 68 Regulation ................................................... 47 Firmware Upgrade ........................................................... 29 Flash Programming Protocol............................................ 31 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 172 Flash Upgrade...................................................................29 Flash Upgrade Example....................................................30 Global Positioning System (GPS) Features ......................66 Global Positioning System (GPS) Technical Specifications ......................................................................................66 Handling Precautions related to electrostatic discharge control...........................................................................17 HSDPA on Linux..............................................................93 HSDPA Operating Modes ................................................95 Internal Registers ............................................................109 International Modem Restrictions.....................................46 Interrupt Sources and Reset Control Table MT5692SMI ...............................................................128 SocketModem (MT9234SMI).....................................110 Japan Regulations .............................................................50 Jumper – 5V / 3.3V...........................................................22 Label Example for Analog SocketModems ......................42 Labeling Requirements .....................................................40 Labeling Your Product......................................................40 Maintenance of Your Modem ...........................................44 Mechanical Drawing in Millimeters for Analog Modems 19 Mechanical Drawings SocketModem CDMA (MTSMC-C) ............................69 SocketModem Cell – Voice Build (MTSMC-G2 V) ....61 SocketModem Cell (MTSMC-G2) ...............................60 SocketModem Cell –l GPS Build (MTSMC-G2-GP) ...63 SocketModem EDGE (MTSMC-E1)............................78 SocketModem EDGE with Voice (MTSMC-E1-V) .....79 SocketModem HSDPA (MTSMC-H) ...........................87 SocketModem HSDPA-USB (MTSMC-H-U)..............88 SocketModem iCell – IP Build (MTSMC-G2-IP) ........62 SocketWireless Wi-Fi (MT810SWM-L-IP)................159 Wi-Fi (MT810SWM-IP).............................................158 Microphone and Speaker for SocketModem MT5692SMI ..............................................................136 Microphone Input for EDGE ............................................83 Microphone Inputs for MTSMC-G2.................................64 New Zealand Telecom Warning Notice............................48 Parallel Interface Index SocketModem (MT5692SMI) .................................... 124 SocketModem (MT9234SMI) .................................... 107 Parallel Interface Register Table SocketModem (MT5692SMI) .................................... 125 SocketModem (MT9234SMI) .................................... 109 Parallel Pin Configurations MT5692SMI............................................................... 121 SocketModem (MT9234SMI) .................................... 104 Parallel Timing Requirements SocketModem (MT5692SMI) .................................... 123 SocketModem (MT9234SMI) .................................... 106 Parts................................................................................ 151 Parts for Analog SocketModems...................................... 39 PC Board Layout Guidelines............................................ 16 Pin Configurations SocketEthernet IP (MT100SEM-IP) .......................... 149 SocketModem (MT2456SMI-22)............................... 143 SocketModem (MT2492SMI) .................................... 139 SocketModem (MT9234SMI) .................................... 103 SocketWireless Bluetooth (MTS2BTSMI)................. 166 Pin Out SocketModem Parallel Build (MT5692SMI) ............. 120 Pin Outs SocketModem (MT5692SMI) .................................... 119 Power Measurements SocketEthernet IP (MT100SEM-IP) .......................... 150 SocketModem (MT2492SMI) .................................... 138 SocketModem (MT5692SMI) .................................... 122 SocketModem (MT9234SMI) .................................... 101 SocketModem CDMA (MTSMC-C)...................... 68, 71 SocketModem Cell & iCell (MTSMC-G2 Family) ...... 58 SocketModem EDGE (MTSMC-E1) ........................... 82 SocketModem HSDPA (MTSMC-H) .......................... 90 SocketWireless Bluetooth (MTS2BTSMI)................. 165 Power Saving Feature for HSDPA ................................... 96 Product Ordering Information MT2456SMI-22 ......................................................... 141 SocketEthernet IP (MT100SEM-IP) .......................... 147 SocketModem (MT2492SMI) .................................... 137 SocketModem (MT5692SMI) .................................... 115 SocketModem (MT9234SMI) .................................... 100 SocketModem CDMA (MTSMC-C)............................ 67 SocketModem Cell & iCell (MTSMC-G2 Family ....... 56 SocketModem EDGE (MTSMC-E1) ........................... 76 SocketModem HSDPA (MTSMC-H) .......................... 84 SocketWireless Bluetooth (MTS2BTSMI)................. 164 SocketWireless Wi-Fi (MT810SWM-IP)................... 155 Programmable Baud Rates Table SocketModem (MT5692SMI) .................................... 133 SocketModem (MT9234SMI) .................................... 113 Provisioning for CDMA................................................... 73 Receiver Features for EDGE............................................ 83 Receiver Features for HSDPA.......................................... 91 Reset................................................................................. 13 RF Interface MTSMC-G2 ................................................................. 64 SocketModem CDMA (MTSMC-C)............................ 72 SocketModem EDGE (MTSMC-E1) ........................... 83 RoHS Compliance............................................................ 52 Safety Warning Telecom.................................................. 44 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 173 SocketModem CDMA Interfaces......................................72 South African Statement, Regulations ..............................48 Speaker Output for EDGE ................................................83 Stereo jack feed jumper ....................................................22 Switch Block.....................................................................22 Technical Specifications SocketEthernet IP (MT100SEM-IP) ...........................148 SocketModem (MT2456SMI-22) ...............................142 SocketModem (MT2492SMI).....................................138 SocketModem (MT5692SMI).....................................117 SocketModem (MT9234SMI).....................................101 SocketModem CDMA (MTSMC-C) ............................68 SocketModem Cell & iCell (MTSMC-G2 Family) ......57 SocketModem EDGE (MTSMC-E1)............................77 SocketModem HSDPA (MTSMC-H) ...........................85 SocketWireless Bluetooth (MTS2BTSMI) .................165 SocketWireless Wi-Fi (MT810SWM-IP) ...................156 Telecom Approvals...........................................................45 Temperature Control for HSDPA .....................................96 Tip and Ring Interface Index SocketModem (MT2456SMI-22)............................... 145 SocketModem (MT5692SMI) .................................... 134 SocketModem (MT9234SMI) .................................... 114 Transmitter Features for EDGE........................................ 83 Transmitter Features for HSDPA ..................................... 91 Universal Developer Kit contents .................................... 11 Universal Pin Descriptions............................................... 12 Universal Socket Design .................................................. 10 USB Interface for HSDPA ............................................... 98 WEEE Directive............................................................... 51 Wireless Approvals .......................................................... 37 XMODEM Serial Port Upgrade ....................................... 30 Multi-Tech Systems, Inc. Universal Socket Hardware Guide for Developers (S000342L) 174
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2009:11:20 08:44:33-08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2009:11:20 08:44:33-08:00 Format : application/pdf Title : Microsoft Word - MTSMC-C1 DRAFT S000342L.doc Creator : Johee_Chang Document ID : uuid:5c6831c5-2541-41d8-b358-554ecd211567 Instance ID : uuid:1372e4a3-a913-4702-9dab-c8bca9cd17ad Page Count : 174 Author : Johee_ChangEXIF Metadata provided by EXIF.tools