Mun Ah Plastic Electronic Toys CTX-8000 2.4 GHz Transmitter User Manual ctx8000 1

Download:
Mirror Download [FCC.gov]
Document ID	2440263
Application ID	hj20cGW5X8JAwxcSGaJDxw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	196.58kB (2457229 bits)
Date Submitted	2014-11-10 00:00:00
Date Available	2014-11-10 00:00:00
Creation Date	2014-11-05 11:14:48
Producing Software	Adobe PDF library 10.01
Document Lastmod	2014-11-05 16:20:49
Document Title	ctx8000 (1)
Document Creator	Adobe Illustrator CS6 (Macintosh)

Declaration of Conformity
Products: Carisma CTX-8000 2.4GHz Transmitter, MRX2800 Receiver
Equipment Class: 2
The objects of declaration described above are in conformity with the requirements of the specifications listed below.
Item Name : Carisma CTX-8000 2.4GHz Transmitter and MRX2800 Receiver
ETSI EN 300 328 V1.8.1
EN 301 489-1 V1.9.2
EN 301 489-17 V2.2.1
Directive 1999/5/EC (R&TTE)
Article 3.1a Health
Article 3.1b EMC
Article 3.2 Radio Spectrum
FCC ID YDTCTX-8000
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: Modifications to this product will void the user’s authority to operate this equipment.
RF Exposure Warning:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
And should be operated with minimum distance of 20 cm between the antenna & your body.
Carisma CTX-8000 2.4GHz FHSS Technology System
The following is an overview of the various functions and adjustments found on CTX-8000 radio system for Carisma models. It is important to read and understand about all of these
functions and adjustments before driving.
Power ON / OFF the Transmitter
The Transmitter CTX-8000
Steering Wheel : Control direction (Left / Right) of the RC model.
Throttle Trigger : Control speed (Forward/Brake/Backward)
of the driving model.
Antenna : Transmit signal to the model.
Power ON / OFF : Power ON / OFF the transmitter
SYNC & Battery Indicator : Green LED light indicates synchronization status and/or adequate
battery power supply. Red LED light indicates low battery
Dual Rate Dial : Adjust the same maximum steering angle on both sides
when model turns Left / Right
ST. Trim Dial : Adjust the neutral position of steering servo when model
wheels are straight ahead.
TH. Trim Dial : Make sure the model stays still when releasing the
throttle trigger.
Battery Compartment Tray : Cover and hold the batteries powering the transmitter.
Throttle
Trim Dial
Steering
Trim Dial
ST.TRIM
Power
ON / OFF
ST
TH.TRIM
TH
Steering
Reverse Switch
Throttle
Reverse Switch
Dual Rate Dial
FTN Key
* In general, user will experience under steer when making a wide turn at
high speed or over steer when making sharp turn at high speed (easy to
spin out). User should practice the throttle and steering approach for
different cornering at different speed or road surface.
CTX-8000
Battery Installation
Supplied with 4 x 1.5V AA Batteries,
CTX-8000 can be operated a few hours.
Installation: Remove the battery
compartment cover as shown below.
Install the batteries observing
the polarity marked on battery
compartment.
Battery LED Indicator
Then reinstall the battery
compartment cover as the
Picture shown below.
Pre-Run Check
The LED indicator located on the front left side of the transmitter indicates the power
supply of batteries. The green LED will go solid on indicating that the batteries have
sufficient power. When batteries voltage drops below 3.8 volts, the Red LED will be
flashing slowly, indicating the batteries power is low and should be replaced.
ST.TRIM
TH.TRIM
ST
TH
Solid Green :
Sufficient Power supply
Red LED Flashing:
Time to replace batteries
Green
For Transmitter
ST.TRIM
TH.TRIM
ST
TH
ATTENTION
x4
Heavy Duty
1.5V “AA” Size Batteries
Warning : Never disassemble batteries or
put the batteries in fire, chemical agents,
otherwise they may cause personal injuries
or property damages.
Battery Disposal : Observe corresponding
regulations about wasted battery treatment
regulations.
1. After running out of power, dispose of
wasted batteries in designated areas far
away from water supply, household areas
and planted areas.
2. Submit the wasted batteries to specific
recycling stations.
Damages or Leaking
Do not use any damaged
batteries.
1. Steering : Adjust the steering trim to
keep the front wheels in straight line
when steering wheel remains in
NEUTRAL position.
2. Throttle : Adjust the throttle trim to
ensure the rear wheels stop rotating
when throttle trigger remains in
NEUTRAL position.
* Always turn on the transmitter first (except doing synchronizing) by
sliding the switch on the left side from bottom to top. The green lights
above the switch should light up. If not, you need to check for low or
incorrectly installed batteries.
Instructions for Disposal of WEEE by
Users in the European Union
This product must never be thrown away with other waste. Thus the users are liable
for disposing the wasted model by submitting them to designated collection stations
specific for recycling electronic and electric items. Disposing of the wasted model in
this way is helpful to conserve natural resources and enable to keep human health
and protect the environment. For more information about wasted model disposal and
recycling, please contact your local city office, your disposal service or where you
purchased the product.
ABOUT THE RADIO SYSTEM
Top Control Panel
ST.TRIM
ST.TRIM
ST
TH.TRIM
TH.TRIM
ST
TH
TH
Throttle Reverse Switch
Dual Rate Dial
Steering Reverse Switch
Dual Rate Dial
Trimming
Dual Rate Dial enables to adjust the same maximum steering angle of servo on
both sides (Left and Right) when model makes steering. The Dual Rate Dial affects
the sensitivity of servo. Reducing dual rate value can lower the sensitivity of servo
and reduce the same maximum steering angle on both sides. Remember to adjust
the dual rate value within the adjustment range.
ST.TRIM
Reversing
C TX-8000 features two trimming
functions:
Steering Trim and Throttle Trim.
Steering Trim Dial :
Adjust the neutral position of steering
servo when the wheels are straight ahead.
Normally steering trim is adjusted until the
model can keep straight tracks.
Throttle Trim Dial :
Adjust the throttle trim to ensure the
rear wheels stop rotating when throttle
trigger remains in NEUTRAL position.
TH.TRIM
ST
TH
Reversing is used to change the response direction of steering wheel and throttle
trigger. CTX-8000 Transmitter features 2 reversing functions: Steering Reverse
and Throttle Reverse.
Steering Reverse: Reverse the response direction when operating steering
wheel. Turning left steering wheel, the model turns right while turning right the
model turns left.
Throttle Reverse: Reverse the response direction when operating throttle trigger.
Pushing forward throttle trigger the model moves backward while pulling back,
the model moves forward. If necessary you can just use a small screwdriver to
adjust the corresponding switches.
RECEIVER CONNECTION AND INSTALLATION
Carisma 2.4GHz Receiver MRX2800
Setup Button
Auxiliary Port
(Reserved)
Antenna Cable
Throttle Port
Steering Port
Auxiliary Port (Reserved)
Steering Port : Where to plug in the servos.
Throttle Port : Where to plug in the Electronic
Speed Controler (ESC).
Setup button : Synchronize transmitter and receiver.
Select frame rate.
Warning :
• Never bend the metal pins on the PCB of receiver.
• Never cut the antenna cable.
• Install the antenna vertically as shown in the figure.
• Keep the antenna as far away from the motor, ESC
and other noise sources as you possibly can.
Tips :
• Wrap the receiver with something soft, such as foam
rubber, to avoid vibration. If there is a chance of getting
wet, put the receiver in a waterproof bag or balloon.
MRX2800
Install the antenna vertically to
the ground.
Remarks :
The mounting positions of receiver
and antenna cable greatly affect
the operating range.
Synchronization & Frame Rate Adjust
Setup Key of Receiver
ST.TRIM
ST.TRIM
1. Prior to any operation make sure the transmitter and receiver are both turned off.
2. Press and hold the setup button on the receiver while power on the receiver.
3. Release the setup button till green LED flashes.
4. Press the setup button to select the frame rate with green LED flashing.
Faster Flashing = High frame rate (7ms) for digital servo
Slower Flashing = Low frame rate (15ms)for analogue servo
5. Power on the transmitter. With the transmitter steering wheel and throttle trigger
in neutral position (full stop and straight steering), press the FTN Key of the
transmitter.
6. When synchronization is done, the green LED on both receiver and transmitter
will turn solid on.
ST
TH.TRIM
TH.TRIM
TH
TH
ST
FTN Key

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2014:11:05 11:14:48+08:00
Creator                         : Adobe Illustrator CS6 (Macintosh)
Modify Date                     : 2014:11:05 16:20:49+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : ctx8000 (1)
Creator Tool                    : Adobe Illustrator CS6 (Macintosh)
Metadata Date                   : 2014:11:05 16:20:49+08:00
Thumbnail Width                 : 172
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 12628 bytes, use -b option to extract)
Document ID                     : xmp.did:961D93141F20681183D1BA3AC73D5CE3
Instance ID                     : uuid:cfd8c6d4-6aba-f94e-b2cc-74b12d4e7265
Original Document ID            : uuid:502463FF862BE1119632D21572979D35
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:6b3f354a-8ab6-4940-8aa7-ffb5ae4e55c5
Derived From Document ID        : xmp.did:0880117407206811822ACE3E16879312
Derived From Original Document ID: uuid:502463FF862BE1119632D21572979D35
Derived From Rendition Class    : default
History Action                  : saved, saved
History Instance ID             : xmp.iid:0280117407206811994CC8BA6A96F6AB, xmp.iid:961D93141F20681183D1BA3AC73D5CE3
History When                    : 2012:05:14 16:59+08:00, 2014:11:05 11:14:43+08:00
History Software Agent          : Adobe Illustrator CS4, Adobe Illustrator CS6 (Macintosh)
History Changed                 : /, /
Startup Profile                 : Print
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 190.001495
Max Page Size H                 : 280.006337
Max Page Size Unit              : Millimeters
Font Name                       : HelveticaLTStd-Cond, HelveticaLTStd-BoldCond, HelveticaLTStd-BlkCond
Font Family                     : Helvetica LT Std, Helvetica LT Std, Helvetica LT Std
Font Face                       : Condensed, Bold Condensed, Black Condensed
Font Type                       : Open Type, Open Type, Open Type
Font Version                    : OTF 1.029;PS 003.001;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 003.001;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 003.000;Core 1.0.33;makeotf.lib1.4.1585
Font Composite                  : False, False, False
Font File Name                  : helveticaltstd-cond.otf, helveticaltstd-boldcond.otf, helveticaltstd-blkcond.otf
Plate Names                     : Black
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants Cyan    : 80.000000
Swatch Groups Colorants Magenta : 5.000001
Swatch Groups Colorants Yellow  : 10.000002
Swatch Groups Colorants Black   : 0.000000
Swatch Groups Group Name        : Grayscale
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: K=5
Swatch Groups Colorants Mode    : GRAY
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Gray    : 12
Producer                        : Adobe PDF library 10.01
Page Count                      : 3

EXIF Metadata provided by EXIF.tools