NABCO Entrances ACUMOTION ND-600 Sensor User Manual SR 02602
NABCO Entrances, Inc. ND-600 Sensor SR 02602
Contents
- 1. User Manual
- 2. Adjustment manual
Adjustment manual
SR-02602
Adjustment Manual for Acumotion Prototype
1. Parts list
1)Acumotion: pc
2)3 conductor
Cable: pc (5ft)
3)Antenna:pc
There are two type of the Antenna, such as Wide field which has 3 chips and
Narrow Field which has 6 chips.
2. Function of LED
Sensor
Status Power ON &
No Detection Microwave
detects Infrared
detects Microwave &
Infrared detect
LED
Status Green Orange Red Off
3. Adjustment
1) Lever for mounting angle of entire sensorLever for mounting angle of entire sensor
This white lever is to adjust the angle of the entire sensor and will be used to
adjust the field of the around threshold for Infrared. When you move this
white lever to upside, sensing field will be move to close side of the door.
9 positions adjustment is available. (-4 ~ 4 deg.)
2) Angle adjustmeAngle adjustment for Microwave sensornt for Microwave sensor
This part is to adjust the angle of microwave head.
11 positions adjustment is available. (15 ~ 45 deg.)
1
2
3
4
5 6
SR-02602
3) Depth adjustment lever of Infrared sensor Depth adjustment lever of Infrared sensor
This slidable lever is to adjust the depth of infrared field.
Lever position [1] : Depth of infrared field 1 ft
Lever position [2] : Depth of infrared field 2 ft
Lever position [3] : Depth of infrared field 3 ft
When you need the enough depth of microwave field, please adjust this
lever ,there is no detection zone between Infrared beams and microwave
beams.
4) Dip Switch 1Dip Switch 1 (8 positons)
This switches are for Infrared sensor.
Switch
Number Function Adustment
1 2
ON ON Mode A
ON OFF Mode B
OFF ON Mode C
1, 2 Mutual
Interference
Prevention Mode OFF OFF Mode D
3 4
ON ON High Sensitivity 15 sec
ON OFF High Sensitivity sec
OFF ON Low Sensitivity 30 sec
3, 4 Sensitivity&
Presence time
adjustment OFF OFF Snow Mode 15 sec
ON ON No Cancellation
OFF ON One spot of left outside
is cancelled.
OFF OFF Two spots of left outside
are cancelled.
ON OFF Three spots of left
outside are cancelled.
ON ON No Cancellation
ON OFF One spot of Right
outside is cancelled.
OFF OFF Two spots of Right
outside are cancelled.
5, 6, 7, 8 Adjustment of
width
OFF ON Three spots of Right
outside are cancelled.
SR-02602
5) Dip Switch 2 (4 positions)
This switches for the microwave sensor.
Switch
Number Function Adjustment
ON Uni-directional
1 Bi/Unidirectional OFF Bi-directional
ON ON Standard
ON OFF High
OFF ON Noise prevention Mode 1
2, 3 Sensitivity of
Frequency Noise
OFF OFF Noise prevention Mode 2
ON Effective
4 Infrared ON/OFF OFF Invalid
6) Sensitivity of power for Microwave sensor (Potentiometer)
10 positions adjustment of sensitivity is available by a potentiometer.
CW: High Sensitivity, CCW: Low Sensitivity High
4. Wiring
Red: 12VDC Input
Black: 12VDC Ground & Output Common
White: Out put (DC30V/0.1A max)
Compliance Statement (Part 15.19)Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Warning (Part 15.21)Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF Exposure (OET Bulletin 65)RF Exposure (OET Bulletin 65)
To comply with FCC RF exposure requirements for mobile transmitting device, this
transmitter should only be used or installed at locations where there is at least 20
cm(7.78 inches) separation distance between the antenna and all person.