NEAT Electronics 0701404 Data handling transceiver User Manual D TECT

NEAT Electronics AB Data handling transceiver D TECT

User manual

Serial bus radio interfaceUser manualD-TECT NE41 08002-02 v2.2
2 D-TECT User manual NE41 08002-02 v2.2EU NotesWhen the device is used it complies to essenal requirements and relevant provisions. A complete Declaraon of Conformity can be obaned from the address below (see “Contact”)US NotesFCC ID: 2AGLF0701404Changes or modicaons not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separaon between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Ulrik LundbergManaging directorInformaon in this User manual is subject to change without noce.NEAT Electronics AB reserves the right to change or improve their products and to make changes to the content without obligaon to nofy any person or organizaon of such changes or improvements.NEAT Electronics AB is not responsible for any loss of data, income or any consequenal damage whatsoever caused.For more informaon, details and descripons, visit our web site:www. neat-group.com© NEAT Electronics AB 2016All rights reserved.Document number: NE41 08002-02 v2.2Revision date: 2016-03-09Contact NEAT Electronics AB Varuvägen 2 SE-246 42 Löddeköpinge SwedenPhone: +46 (0)46 707065Fax: +46 (0)46 707087www.neat-group.com/se/eninfosweden@neatgroup.com
3D-TECT User manual NE41 08002-02 v2.2In the package 3Hardware overview 3Installaon 4LEDs 4JumperJ1 4Connecon 5Important 5Safety Notes 5Use 6Cleaning 6Disposal 6Technical data 7In the package1 x D-TECT unit2 x Antenna1 x This user manualShould any part be missing, please contact your distributor.Hardware overview#Denominaon①Antenna connector x 2②Power switch③Not used④Jumper J1⑤LED x 2⑥Rotary switch⑦AC/DC adapter connector⑧Serial bus connector x 2⑨Antenna x 21372658 8914Content
4 D-TECT User manual NE41 08002-02 v2.2Installaon1. Open the cover and select the bus addres by turning the rotary switch to the desired address value, 1-9 or A-F.The value of the rotary switch must be set to other than 0 (zero) for the unit to work!2. Close and fasten the lid using the screws supplied.3. Connect the antennas by screwing them into the antenna connectors.4. Mount the D-TECT unit in an ap-propriate place.5. Connect one or two cables for the serial bus and central power supply to the two connectors marked BUS .6. If no central power supply is used, connect an AC/DC-adapter to the jack marked DC . Then connect the AC/DC adapter to a mains outlet in the apartment.Only use AC adaptor for your region, see Technical Data.7. Turn on the D-TECT unit with the power switch marked ON OFF .LEDsThe green LED marked Power burns with a steady light when the unit is powered on.The red LED marked Activity blinks to indicate that D-TECT is communicat-ing on the serial bus.If both the red and the green LED is blinking in phase with each other, the D-TECT unit is not working properly. Please contact NEAT Electronics or your local distributor.Jumper J1Jumper J1 is a 100 Ω terminaon of the serial bus and must be mounted on the LAST D-TECT if the total length of the serial bus is > 500m.
5D-TECT User manual NE41 08002-02 v2.2ConneconThe serial bus cable is connected as shown in the image below.81#Connecon①RS-485 bus, wire A (-)②RS-485 bus, wire B (+)③Not connected④24 VDC⑤Common ground⑥Not connected⑦24 VDC⑧Common groundImportantSafety Notes• Read instrucons prior to use• Always test the system per instrucons prior to use and always check the funcon of the product aer making adjustmentsThis product may not be suitable for all persons.• This product should not be a substute for the roune visual monitoring protocol by caregiver and must not be used in situaons where a delay in the arrival of ap-propriate medical care, could lead to a potenally life-threatening situaon.• Our units are NOT intended for any life support device, thus intending a device whose malfunc-on may result in damage to a life.• Check the device regularly and replace when necessary.• Do not integrate to other systems other than those specied in this document.• The product will not cause electromagnec disturbances under normal working condions.• The product can be placed near other products or devices as long as mechanical vibraon is not present.• Remove baeries if the unit is to be out of use or stored for an extended period of me.
6D-TECT User manual NE41 08002-02 v2.2Use• Use only original parts.• Keep away from dust, moist and dirt.• Do not drop, knock, twist or shake the device.• Do not warm up the device or use it near re.• The product may not be painted.• For repairs, contact a NEAT dealer.Cleaning• All parts in the product kit can be cleaned with a mild soap soluon and a damp cloth. Dry with a dry cloth.• Strong chemicals, grease and other harsh substances must not be used when cleaning or handling the parts in the product kit.• The product must be disconnected from the power socket before cleaning.• Aer cleaning, control that the product works properly by sending a test alarm to the alarm receiver/central.DisposalAt the end of the product’s use life, please dispose of it at appropriate collecon points provided in your country. For disposal or recycling informa-on, please contact your local authories or the Electronic Industries Alliance (EIA, www.eiae.org). In the European Union, the bin label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling or returned to NEAT Electronics.
7D-TECT User manual NE41 08002-02 v2.2Technical dataPower supply 10-24 VDC, 3WPower comsumpon 125 mA @ 24 VDCMeasures (W x H x D) 111 x 67 x 28 mm(111 x 111 x 28 incl. antennas)Weight 105 g (incl. antennas)Temp. range +5 - +55oCRF-Frequency EU US869.2 MHz (Social alarms) Category 1916.2 MHz869.4 MHz 916.4 MHzBandwidth 25 kHzSerial bus type RS-485 mul dropThe frequencies for each market are programmed during producon and not changeable by the user.Recommended AC AdaptorsCountry/region Arcle numberEU NE31 07010-01UK NE31 07010-03US NE31 07010-02
www.neat-group.com/se/en

Navigation menu