NEAT Electronics 0701404 Data handling transceiver User Manual D TECT
NEAT Electronics AB Data handling transceiver D TECT
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2927623 |
| Application ID | b+2PzZxM8OGvdbZw+mf1uA== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 47.29kB (591152 bits) |
| Date Submitted | 2016-03-12 00:00:00 |
| Date Available | 2016-03-13 00:00:00 |
| Creation Date | 2016-03-09 14:43:11 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2016-03-09 14:43:12 |
| Document Title | D-TECT User manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
| Document Author: | Kim Berntson |
D-TECT Serial bus radio interface User manual NE41 08002-02 v2.2 Information in this User manual is subject to change without notice. NEAT Electronics AB reserves the right to change or improve their products and to make changes to the content without obligation to notify any person or organization of such changes or improvements. NEAT Electronics AB is not responsible for any loss of data, income or any consequential damage whatsoever caused. For more information, details and descriptions, visit our web site: www. neat-group.com EU Notes When the device is used it complies to essential requirements and relevant provisions. A complete Declaration of Conformity can be obtianed from the address below (see “Contact”) US Notes FCC ID: 2AGLF0701404 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. © NEAT Electronics AB 2016 All rights reserved. Document number: NE41 08002-02 v2.2 Revision date: 2016-03-09 Contact NEAT Electronics AB Varuvägen 2 SE-246 42 Löddeköpinge Sweden Ulrik Lundberg Managing director Phone: +46 (0)46 707065 Fax: +46 (0)46 707087 www.neat-group.com/se/en infosweden@neatgroup.com D-TECT User manual NE41 08002-02 v2.2 Content In the package In the package Hardware overview Installation LEDs Jumper J1 Connection Important Safety Notes Use Cleaning Disposal Technical data 1 x D-TECT unit 2 x Antenna 1 x This user manual Should any part be missing, please contact your distributor. Hardware overview ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ D-TECT User manual NE41 08002-02 v2.2 Denomination Antenna connector x 2 Power switch Not used Jumper J1 LED x 2 Rotary switch AC/DC adapter connector Serial bus connector x 2 Antenna x 2 Installation 1. Open the cover and select the bus addres by turning the rotary switch to the desired address value, 1-9 or A-F. The value of the rotary switch must be set to other than 0 (zero) for the unit to work! 2. Close and fasten the lid using the screws supplied. 3. Connect the antennas by screwing them into the antenna connectors. 4. Mount the D-TECT unit in an appropriate place. 5. Connect one or two cables for the serial bus and central power supply to the two connectors marked BUS . 6. If no central power supply is used, connect an AC/DC-adapter to the jack marked DC . Then connect the AC/DC adapter to a mains outlet in the apartment. 7. Turn on the D-TECT unit with the power switch marked ON OFF . LEDs The green LED marked Power burns with a steady light when the unit is powered on. The red LED marked Activity blinks to indicate that D-TECT is communicating on the serial bus. If both the red and the green LED is blinking in phase with each other, the D-TECT unit is not working properly. Please contact NEAT Electronics or your local distributor. Jumper J1 Jumper J1 is a 100 Ω termination of the serial bus and must be mounted on the LAST D-TECT if the total length of the serial bus is > 500m. Only use AC adaptor for your region, see Technical Data. D-TECT User manual NE41 08002-02 v2.2 Connection Important The serial bus cable is connected as shown in the image below. Safety Notes ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Connection RS-485 bus, wire A (-) RS-485 bus, wire B (+) Not connected 24 VDC Common ground Not connected 24 VDC Common ground D-TECT User manual NE41 08002-02 v2.2 • Read instructions prior to use • Always test the system per instructions prior to use and always check the function of the product after making adjustmentsThis product may not be suitable for all persons. • This product should not be a substitute for the routine visual monitoring protocol by caregiver and must not be used in situations where a delay in the arrival of appropriate medical care, could lead to a potentially life-threatening situation. • Our units are NOT intended for any life support device, thus intending a device whose malfunction may result in damage to a life. • Check the device regularly and replace when necessary. • Do not integrate to other systems other than those specified in this document. • The product will not cause electromagnetic disturbances under normal working conditions. • The product can be placed near other products or devices as long as mechanical vibration is not present. • Remove batteries if the unit is to be out of use or stored for an extended period of time. Use • • • • • • Use only original parts. Keep away from dust, moist and dirt. Do not drop, knock, twist or shake the device. Do not warm up the device or use it near fire. The product may not be painted. For repairs, contact a NEAT dealer. Cleaning • All parts in the product kit can be cleaned with a mild soap solution and a damp cloth. Dry with a dry cloth. • Strong chemicals, grease and other harsh substances must not be used when cleaning or handling the parts in the product kit. • The product must be disconnected from the power socket before cleaning. • After cleaning, control that the product works properly by sending a test alarm to the alarm receiver/central. Disposal At the end of the product’s use life, please dispose of it at appropriate collection points provided in your country. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (EIA, www.eiae.org). In the European Union, the bin label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling or returned to NEAT Electronics. D-TECT User manual NE41 08002-02 v2.2 Technical data Power supply 10-24 VDC, 3W Power comsumption 125 mA @ 24 VDC Measures (W x H x D) 111 x 67 x 28 mm (111 x 111 x 28 incl. antennas) Weight 105 g (incl. antennas) Temp. range +5 - +55oC RF-Frequency EU US 869.2 MHz (Social alarms) Category 1 916.2 MHz 869.4 MHz 916.4 MHz Bandwidth 25 kHz Serial bus type RS-485 multi drop The frequencies for each market are programmed during production and not changeable by the user. Recommended AC Adaptors Country/region Article number EU NE31 07010-01 UK NE31 07010-03 US NE31 07010-02 D-TECT User manual NE41 08002-02 v2.2 www.neat-group.com/se/en
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Format : application/pdf Title : D-TECT User manual Creator : Kim Berntson Subject : D-TECT, 100x106, User manual Description : NE41 08002-00 Create Date : 2016:03:09 14:43:11+01:00 Metadata Date : 2016:03:09 14:43:12+01:00 Modify Date : 2016:03:09 14:43:12+01:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:edb48de3-f434-4823-b148-00d75ae53a8d Original Document ID : xmp.did:B4786302BD11E011B896F2037D90A15C Document ID : xmp.id:93F07496FCE5E51198F4B85140BB24B7 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:92F07496FCE5E51198F4B85140BB24B7 Derived From Document ID : xmp.did:F38A49D593B3E111B3D2914DDCB5E6DD Derived From Original Document ID: xmp.did:B4786302BD11E011B896F2037D90A15C Derived From Rendition Class : default Derived From Manager : AdobeARM History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:03:09 14:43:11+01:00 Date Created : 2011:01:20 Warning : [minor] Fixed incorrect URI for xmlns:swf Background Alpha : 0 Marked : True Producer : Adobe PDF Library 10.0.1 Trapped : False Creator Work Telephone : +46 46 59 00 155 Creator Work Email : kb2neatelectronics.se Creator Work URL : www.neatelectronics.se Page Layout : OneColumn Page Count : 8 Author : Kim BerntsonEXIF Metadata provided by EXIF.tools