NETWORK KOREA AEWC-2000 Web Camera User Manual CCD manual

Download:
Mirror Download [FCC.gov]
Document ID	242752
Application ID	0zk2S/xLBlf0O/ff+9aBHw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.66kB (145744 bits)
Date Submitted	2002-05-13 00:00:00
Date Available	2002-05-13 00:00:00
Creation Date	2002-05-13 19:30:19
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2002-05-13 19:30:19
Document Title	Microsoft Word - CCD_manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	csr

Acknowledgement
1. ATEYE Web camera Items & Specifications
Thank you very much for purchasing the ATEYE of Network Korea.
1) Items
• ATEYE Web Camera is developed and produced with only Korean
2) Specifications
technologies.
• ATEYE Web Camera is marketed and sold after thorough quality verification.
2. ATEYE Web Camera Installation
• ATEYE Web Camera guarantees the rights and interests of consumers with
1) Setting ATEYE Web Camera
perfect customer service.
1.1) Setting the camera ID
• ATEYE Web Camera will expand the ranges of your selection with various
1.2) Setting baud rate
products.
1.3) Setting termination
2) Composite cable ( BNC & RCA )
3) Connecting serial cable
Customer Service Center
st
• Address: 1 Daeryug Techno Town, 327-24, Kasan-dong, Keumcheon-gu,
Seoul, 153-023, Korea.
• Tel: 02-857-5455
3. ATEYE Web Camera Protocol
• Fax: 02-857-5480
• URL: WWW.NETKOREA4U.COM
4. Troubleshooting
Copyright
• The software and hardware mentioned in this user manual are the property of Network
Korea Co., Ltd. All software and hardware are protected by computer program protection
act, copyright act and international copyright conventions including other intellectual
property acts and conventions. No part of this manual may be reproduced or transmitted in
any form or by any means without permission in writing from Network Korea.
Contents
1. ATEYE Web Camera Items & Specifications
1) Items
(1) ATEYE Web Camera
(4) Composite cable( BNC & RCA )
(2) DC 12V 600mA Adaptor
(5) User’s Manual
(3) Serial Cable (RS485 )
2) Specifications
1) Setting ATEYE Web Camera
ATEYE Web Camera
Video Format
NTSC Standard : 525 Lines
30 Frames/sec
Scanning System
1/4 Interline
Effective Total Pixel No.
510(H) * 492(V)
Signal System
525 Lines Interface
Scanning Frequency
Horizontal : 15.734KHz, Vertical : 59.94Hz
Synchronization
Internal Synchronization
Resolution
More than 360 Lines
Signal Output
Analog Composite (1.0Vp-p, 75 ohm)
S/N ratio
More than 48dB
Minimum Illumination
2Lux
Gamma
0.45
Motion range
PAN : 320° TILT : -30° ~ +45°
Maximun Pan Speed
80°/sec
Maximun Tilt Speed
80°/sec
Control Interface
RS485
Preset
64 Positions
Sensor Out
One
Power
DC 12V, 600mA
[Figure.1] the 8-bit DIP switch factory setting
1.1) Setting the camera ID
ATEYE Web Camera has an inherent camera ID. The total number of camera ID
is 64 from number 0 to number 63. How to set the camera ID is followed.
There is a 8-bit DIP switch in the bottom of ATEYE Web Camera
Among those switches in Figure.1, the pins of number 1-6 are used for
setting camera ID.
Number 1 switch is the lowest level bit(LSB) and number 6 is
the highest level bit(MSB).
If the switch is set on, the value is “1”, otherwise, it is “0”. ( binary number )
Example ) In case camera ID is number 5
2. ATEYE Web Camera Installation
Switch number 1 => On
on,
Switch number 2 => Off
Otherwise, you must set the switch of one ATEYE Web Camera on and that of
Switch number 3 => On
the others off.
Switch number 4 => Off
Switch number 5 => Off
the 8-bit DIP switch factory setting is followed.
Switch number 6 => Off
Camera ID : 1
Baud rate : 9600 bps
That is
Termination : On
101000 => Camera ID is number 5
2) Composite cable ( BNC & RCA )
1.2) Setting the baud rate
A composite cable (BNC & RCA connector) is used in video out & Alarm out.
It is described the protocol of Alarm out in detail in the next pages.
ATEYE Web Camera is allowed to use two type of baud rate
3) Connection the serial cable
;4800[bps], 9600[bps].
ATEYE Web Camera originally uses RS485 communications.
Number 7 switch of 8-bit DIP switch is used for that purpose.
The color information of serial cable is followed.
If the switch is on, the baud rate is 9600bps, otherwise it is 4800bps.
camera
red
1.3) Setting the termination
In case that you control more than two ATEYE Web Cameras with one
controller, you must set the termination for preventing the control signal being
controller (DVR etc.)
Rx(+)
Tx(+)
white Rx(-)
Tx(-)
green Tx(+)
Rx(+)
black Tx(-)
Rx(-)
lost.
You can use this by handling the last switch of 8-bit DIP switch at figure.1.
If you use only one ATEYE Web Camera with one controller, the switch must be
It is described the protocol in detail in the next pages
3. ATEYE Web Camera Protocol
0x01
Data Length
1 Byte (8 bit)
Start/Stop Bit
1 Bit
Parity Bit
None
Baud rate
4800bps, 9600bps(default)
0x88
0x10
0x00
0x00
0x00
Cam_ID
Cam_ID
-. RIGHT
0x01
0x88
0x11
0x00
0x00
0x00
Cam_ID
Cam_ID
0x01
0x88
0x22
0x00
0x00
0x00
Cam_ID
Cam_ID
0x88
0x20
0x00
0x00
0x00
Cam_ID
Cam_ID
0x88
0x32
0x00
0x00
0x00
Cam_ID
Cam_ID
0x88
0x33
0x00
0x00
0x00
Cam_ID
Cam_ID
0x88
0x30
0x00
0x00
0x00
Cam_ID
Cam_ID
0x88
0x31
0x00
0x00
0x00
Cam_ID
Cam_ID
-. UP
Protocol Format
start code
Func_num
Data3
Data2
Data1
Data0
Cam_ID
Cam_ID
start code : 0x01
- DOWN
Func_num : Function byte
0x01
Data3 ~ Data0 : Data bytes
Cam_ID : Camera ID
-. LEFT_UP
Check Sum : Check Sum
0x01
Sum = FC_NUM + DATA3 + DATA2 + DATA1 + DATA0 + CAM_ID
Low level byte of Sum is used for Check Sum
-. RIGHT_UP
example
0x01
0x165 = 0x11 + 0x22 + 0x33 + 0x44 + 0x55 + 0x66
Check_sum = 0x65
-. LEFT_DOWN
0x01
-. Pan/Tilt Home(send signal once without signal of stopping )
0x01
0x8a
0x00
0x00
0x00
0x00
Cam_ID
Cam_ID
-. RIGHT_DOWN
0x01
-. LEFT
-. Pan/Tilt Stop
0x01
0x80
0x30
0x00
0x00
0x00
Cam_ID
1) Video output is not shown in the monitor.
Cam_ID
- Is the camera’s power cable attached correctly?
Setting 64 Positions in preset
- Is the BNC cable attached correctly?
-. assignment(Pos_Num : 0x00 ~ 0x3F)
- Is the video output format correct? ( NTSC, Analog Composite
0x01
0x81
0x01
Pos_Num
0x00
0x00
Cam_ID
(1.0V p-p, 75ohm))
Cam_ID
- In case all the above is correct, but it does not work right, please contact us.
-. moving(Pos_Num : 0x00 ~ 0x3F)
0x01
0x81
0x02
Pos_Num
0x00
0x00
Cam_ID
2) Pan/tilt motion of camera does not be controlled.
Cam_ID
- Is the camera’s power LED of the camera on?
Sensor Output( Alarm out )
- Is the switch of 8-bit DIP switch set correctly?
-. Open
- Is the protocol of pan/tilt motion set correctly? (confirm that in chapter 3)
0x01
0x8
0x44
0x00
0x00
0x00
Cam_ID
- Is the serial cable connected correctly?
Cam_ID
- In case all the above is correct, but it does not work right, please contact us.
-. Close
0x01
0x8
0x40
0x00
0x00
0x00
Cam_ID
Cam_ID
4. Troubleshooting
FCC NOTICE
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment of and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user’s authority to operate the
equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:05:13 19:30:19-07:00
Modify Date                     : 2002:05:13 19:30:19-07:00
Page Count                      : 7
Creation Date                   : 2002:05:14 02:30:19Z
Mod Date                        : 2002:05:14 02:30:19Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : csr
Metadata Date                   : 2002:05:14 02:30:19Z
Creator                         : csr
Title                           : Microsoft Word - CCD_manual.doc

EXIF Metadata provided by EXIF.tools