NUMA Electronics B5000ZB Barcode Scanner User Manual MUMA DM0816

NUMA Electronics Inc. Barcode Scanner MUMA DM0816

User manual

Symbologies setting - Enable - DisableHow do you program your scanner? 1.Scan Start Configuration 2.Scan all necessary able for parameters that Meet your application3.Scan end configuration to save the changes. Resetting The Standard Product DefaultsIf you aren’t sure what programming options are in your scanner,or you’ve changed some options and want the factory settingsrestored, scan the bar code below.End Confi gurationInterface selectionReading modeLanguage ………etc.Start Confi gurationStandard Product Default SettingWIRELESS BARCODE SCANNERQuick Start GuideKC-5200ZBFEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/ TV technician for help. CAUTION:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.Labeling requirementsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.RF exposure warningThe equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.The equipment must not be co-located or operating in conjunction with any other antenna or transmitter.
Before Getting StartedAbout your wireless scanner Note: New batteries should be fully charged before their first use USB docking stationUSB Receiver USB recharge cable StrapWireless ScannerIt is one on one wireless data communication protocol. The scanner is already paired with the USB receiver. Just easily plug USB receiver and start the operation. The scanner on a real time basis, if the scanner is connected, the barcode is decoded and transmitted to the remote host without any delay. If the scanner is not connected or out of range, the data is lost (status: 2 beeps/4 beeps).Wake up your wireless scannerPress and release the trigger on your scanner to activate it.Your scanner is ready to work when orange LED comes on .Connect USB receiver to a host computerThe device can be quickly recognized by host computer without any software/driver installation. Within less than10 seconds the receiver will flash red to inform the Initialization is completed.Recharging the batteryThe Red LED comes on when the battery level is low, pleaserecharge the scanner immediately. When the scanner is charging, the LED is green (solid). A full recharge (from completely drained battery) takes approximately 4 hours. When the scanner is fully charged, the green LED will go off.How to pair (repair) you scanner and receiver?Step 1: Plug the USB receiver to the scannerStep 2: Trigger the button on the scanner.Step 3: Devices are successful paired with 1 beep from scanner and 1 blink from the USB receiver.Scanner LED indicatorUSB receiver LED indicatorStatus / indicatorGood ScanTransmissionTrasmission failure(in memory mode)failureLow batteryRechargeOperation modeSleepingBeeper Blue LED Green LED Red LED Orange LED1 beep4 beeps2 beeps4 blink2 blinkNone1 blinkNoneOnNoneOnNoneOnNoneColorRedIndication*High<Buzzer>OffLow<Vibration motor>Enable*Disable<Memory mode>Enable*Disable *10min<Sleep mode>30minalways onDefault setting of wireless scanner•Buzzer : High•Vibrator: Disable•Memory mode: Disable•Power saving (sleep mode): 10min The default values can be modified by scanning the following options.Note: Please scan the following barcode directly with your USB receiver on. No need to scan start and end configuration barcodes.HID USB Keyboard CountryScan the appropriate country code below to program the keyboard for your country. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ Note: Please scan the following barcode directly with your USB receiver on. No need to scan start and end configuration barcodes. Terminator selection USItalianSpanishGermanDanishJapaneseFrenchTurkey

Navigation menu