NUMA Electronics B5000ZB Barcode Scanner User Manual MUMA DM0816

Download:
Mirror Download [FCC.gov]
Document ID	2550378
Application ID	n2SqOmGHajhLIL1/0+lhKA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	161.59kB (2019933 bits)
Date Submitted	2015-03-09 00:00:00
Date Available	2015-03-09 00:00:00
Creation Date	2013-01-11 16:24:42
Producing Software	Adobe Acrobat 8.0
Document Lastmod	2013-01-11 16:24:42
Document Title	MUMA DM0816-æ­£
Document Creator	Adobe Illustrator CS3

How do you program your scanner?
1.Scan Start Configuration
Start Configuration
2.Scan all necessary able for parameters that
Meet your application
Interface selection
Reading mode
Language ………etc.
3.Scan end configuration to save the changes.
End Configuration
Resetting The Standard Product Defaults
If you aren’t sure what programming options are in your scanner,
or you’ve changed some options and want the factory settings
restored, scan the bar code below.
Standard Product Default Setting
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
Symbologies setting
- Enable
- Disable
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
KC-5200ZB
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
BARCODE SCANNER
-Consult the dealer or an experienced radio/ TV technician forWIRELESS
help.
Quick Start Guide
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
Labeling requirements
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
RF exposure warning
The equipment complies with FCC RF exposure limits set forth
for an uncontrolled environment.The equipment must not be
co-located or operating in conjunction with any other antenna or transmitter.
Before Getting Started
Wake up your wireless scanner
Press and release the trigger on your scanner to activate it.
Your scanner is ready to work when orange LED comes on .
Connect USB receiver to a host computer
The device can be quickly recognized by host computer
without any software/driver installation. Within less than
10 seconds the receiver will flash red to inform the Initialization
is completed.
The Red LED comes on when the battery level is low, please
recharge the scanner immediately. When the scanner is
charging, the LED is green (solid). A full recharge (from
completely drained battery) takes approximately 4 hours.
When the scanner is fully charged, the green LED will go off.
How to pair (repair) you scanner and
receiver?
USB docking station
•Buzzer : High
•Vibrator: Disable
•Memory mode: Disable
•Power saving (sleep mode): 10min
The default values can be modified by scanning the following
options.
Scan the appropriate country code below to program the
keyboard for your country. As a general rule, the following
characters are supported, but need special care for countries
other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~
Note: Please scan the following barcode directly with your USB
receiver on. No need to scan start and end configuration
barcodes.
Step 1: Plug the USB receiver to the scanner
Step 2: Trigger the button on the scanner.
Step 3: Devices are successful paired with 1 beep from scanner
and 1 blink from the USB receiver.
Strap
Status / indicator
Beeper
Good Scan
1 beep
1 blink
Transmission
failure
Trasmission failure
(in memory mode)
4 beeps
4 blink
2 beeps
2 blink
Recharge
It is one on one wireless data communication protocol.
The scanner is already paired with the USB receiver. Just
easily plug USB receiver and start the operation. The scanner
on a real time basis, if the scanner is connected, the barcode is
decoded and transmitted to the remote host without any delay.
If the scanner is not connected or out of range, the data is lost
(status: 2 beeps/4 beeps).
Operation mode
Note:
New batteries should be fully charged before their first use
Sleeping
On
Red
*High
Enable
On
None
None
None
Indication
None
None
Note: Please scan the following barcode directly with your USB
receiver on. No need to scan start and end configuration
barcodes.
US
German
Italian
Danish
Spanish
Japanese
French
Turkey
*Disable
Off


*Disable
*10min
Enable
30min
On
USB receiver LED indicator
Color

Blue LED Green LED Red LED Orange LED
Low battery
About your wireless scanner

Low
Scanner LED indicator
USB recharge cable
HID USB Keyboard Country
Recharging the battery
Wireless Scanner
USB Receiver
Default setting of wireless scanner
always on
Terminator selection

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2013:01:11 16:24:42+08:00
Create Date                     : 2013:01:11 16:24:42+08:00
Metadata Date                   : 2013:01:11 16:24:42+08:00
Creator Tool                    : Adobe Illustrator CS3
Format                          : application/pdf
Title                           : MUMA DM0816-正
Document ID                     : uuid:3c516119-5e32-45dc-a5bc-21f6368b1490
Instance ID                     : uuid:eddf5c63-b226-4baa-9cab-9c734ba7bdcc
Producer                        : Adobe Acrobat 8.0
Page Count                      : 2
Creator                         : Adobe Illustrator(R) 13.0
For                             : Administrator,
Bounding Box                    : -55 -55 1075 650
Creator Version                 : 13
Container Version               : 11
Trapped                         : False

EXIF Metadata provided by EXIF.tools