Nanjing Signway Information Technology SWH5186 Media Player Board User Manual
Nanjing Signway Information Technology Co., Ltd Media Player Board
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3885306 |
| Application ID | KkAwDZcwPujdc3N2ObzOfw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 108.11kB (1351409 bits) |
| Date Submitted | 2018-06-12 00:00:00 |
| Date Available | 2018-06-12 00:00:00 |
| Creation Date | 2018-03-20 16:00:07 |
| Producing Software | ç¦æ˜•é˜…读器打å°æœºç‰ˆæœ¬8.3.1.0522 |
| Document Lastmod | 2018-03-20 16:01:08 |
| Document Title | User Manual |
Media Player Board SWH-5186 Specification V2.0 ©2017 Nanjing Signway Technology Co., Ltd. FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The distance between the product and body is more than 20cm Revision history Revision Revision date Principle changes V1.0 Oct. 2016 Create based on SWH-5186 V1.0 V2.1 Sept. 2017 Create based on SWH-5180 V2.0 Copyright © 2017 Nanjing Signway Technology Co., Ltd. All rights reserved. Contents 1 Overview................................................................................................................................................................... 2 1.1 Introduction.......................................................................................................................................................2 1.2 Features............................................................................................................................................................. 2 2 Specification.............................................................................................................................................................. 3 3 Profile........................................................................................................................................................................ 5 3.1 Profile.................................................................................................................................................................5 3.2 Dimensions........................................................................................................................................................ 7 3.3 Structure............................................................................................................................................................ 8 4 Interfaces...................................................................................................................................................................9 4.1 Interface Layout.................................................................................................................................................9 4.2 Interface Description....................................................................................................................................... 10 5 Electrical Performance............................................................................................................................................21 1 Overview 1.1 Introduction SWH-5186 multimedia network player board is designed based on Rockchip RK3288 chip. Which is CPU frequency up to 1.8GHZ and quad-core architecture Cortex-A17 and DDR3 2G memory and 8G of storage. These super-performance ensure high-speed run of terminals . The most eye-catching of the board is supporting 4K H.264 decoding. In addition, this board has rich peripheral interfaces, including TTL, RS232, GPIO multiple expansion interface and HDMI input + HDMI, LVDS, VGA three outputs to support the industry mainstream USB / serial port Equipment; It support camera and printer and identification terminal and two-dimensional code scanner and IC card reader and fingerprint reader and other mainstream peripherals. 1.2 Features (1) the classic version, the new configuration · CPU’s frequency is 1.8GHZ · Quad-core CPU · DDR3 2G memory and 8G storage (expandable TF / USB) · Android 5.1 system (2) complete module, with on-demand · Mainstream 3G / 4G module · Printer, two-dimensional code scanner, camera, identification terminal, fingerprint recognition · NFC identification module · Thermal sensation and gravity sensing module · Wireless charging module (3) rich peripheral interface, flexible choice and expansion · 3 TTL or 1 TTL + 2 RS232 (standard) · 6 TTL or 4 TTL + 2 RS232 (Optional) · 6 USB2.0 interface and 5 GPIO interface · HDMI, LVDS, VGA three output · HDMI input (optional) Signway Media Player Board SWH-5180 SPEC V2.0 Chapter 1 Specification Hardware Configuration CPU Rockchip RK3288 + ARM Quad-core Cortex A17 CPU (Up to 1.8GHz) RAM HYNIX DDR3 2Gbyte Storage 8GB eMMC Memory (extensible TF/USB) GPU ARM Quad Mali-764 GPU Resolution 4K H.264 Decoding OS OS Android 5.1 Contents Support Video/Image/Text/logo/Date/Time/Weekday/Weather split-screen display and background image Media Formats Media Formats Video: MPEG1, MPEG2, MPEG4, H.264, WMV, MKV, TS, flv Audio: MP3 Image: JPG, JPEG, BMP, PNG, GIF Interfaces Power Supply ×1 Video Output VGA×1 (optional) HDMI×1 LVDS×1，40 Pin, 2.0mm, Double Row Video Input HDMI IN×1 Audio Output ×1, Linear output, 3.5mm headphone jack ×2, 2 Pin 2.0mm, Stereo CLASS-D Amplifier, direct for 2*8W/8Ω Speaker Internet ×1, 10/100M Ethernet WIFI(802.11bgn)×1, BT4.0×1 PCIE Slot（2G/3G Module）×1 USB2.0 USB OTG×1（can be used as HOST） USB HOST×5 (J28 and 3G modules share a USB interface) Backlight ×2, 6 Pin, 2.0mm Fan ×2, 2 Pin, 2.0mm IR ×1, 7 Pin, 2.0mm, Red/Green LED Signway Media Player Board SWH-5180 SPEC V2.0 Chapter 1 Overview Extension 3 TTL or 1 TTL + 2 RS232 (standard) 6 TTL or 4 TTL + 2 RS232 (Optional) SPI×1 GPIO×5 I2C×2 MIC x1 TF Card Slot ×1 SIM Card Slot ×1 Other Features RTC Time synchronization over network and time saving when power failure IR Input Specified remote of NEC format Electrical Parameter Input Power Switching Power（STB，5VSB，5V，12V）, 10 Pin, 2.00mm Single 12V (Need to short J41) Signway Media Player Board SWH-5180 SPEC V2.0 3 Profile 3.1 Profile Front View Speaker Right Back light Speaker Left Main Power Input WiFi/BT Antenna Remote WiFi/BT Antenna TTL TTL Fan MIC HDMI IN SPI Extension USB Extension EDP USB Extension 3G Extension USB Extension LAN Audio HDMI LVDS Output MIPI(optional) U_BOOT VGA(optional) USB USB_OTG Note: Serial port type (TTL / RS232) will be different according to the option. Signway Media Player Board SWH-5180 SPEC V2.0 Chapter 2Specification Rear View SIM Signway Media Player Board SWH-5180 SPEC V2.0 TF Chapter 2Profile 3.2 Dimensions Length:145mm, Width:100mm,Front Max. Height: 9mm,Rear Max Height:4mm, Screw Hole:Φ3.5mm Signway Media Player Board SWH-5180 SPEC V2.0 3.3 Structure Speaker Right Left Backlight Power LVDS line Fan LAN/WLAN Signway Media Player Board SWH-5180 SPEC V2.0 4 Interfaces 4.1 Interface Layout Front J4 J41 J5 3G/4G J11 J7 JMP1 J17 ANT5 J18 J32 J18 J37 J42 J38 J46 JMP2 J45 J28 J35 RJ45 CN5 VGA_OUT HDMI_OUT U8 Signway Media Player Board SWH-5180 SPEC V2.0 AU_OUT J24 USB SW1 Chapter 3 Profile Rear J9 J2 4.2 Interface Description · · · J4 Left Speaker Output Pin No. Pin Name Type Description L- Output Left channel negative L+ Output Left channel positive J5 Right Speaker Output Pin No. Pin Name Type Description R- Output Right channel negative R+ Output Right channel positive J7 Main Power Input Pin No. Pin Name Type Description Signway Media Player Board SWH-5180 SPEC V2.0 10 Chapter 3 Interfaces 12V Input Total Power Input, 12V GND Ground Ground 5V Input Total Power Input, 5V GND Ground Ground 5VSB Input Standby Powe, 5V 10 STB Output Standby power control · J11 Backlight Inverter Control Pin No. Pin Name Type Description +12V Backlight Power Output, Switch Controlled, 12V Power Max. Current: 3A Output Large size multi-tube backlight with more than 3A current requires separate power supply ON Output 3.3V Backlight On/Off Signal, High/Low Configured ADJ Output Backlight DIMMING Control GND Ground Ground · J17 Remote Receiver/ Working Indicator/ Button Interface Pin No. Pin Name Type Description IR Input Remote Receiver Input GND Ground Ground 3.3V Red Light Indicates Standby State Green Light Indicates Working State KEY Input Outer Button Input MVC Power 3.3V Power Output Power Output Signway Media Player Board SWH-5180 SPEC V2.0 Remote Power 3.3V 11 Chapter 3 Interfaces Output · · · J18 TTL Serial Port Pin No. Pin Name Type Description NC Reserved NC Reserved GND Ground Ground RX4 Input UART Data Input, TTL TX4 Output UART Data Output, TTL NC Reserved NC Reserved NC Reserved NC Reserved 10 5V Output 5V Type Description J21/ J22 Fan Pin No. Pin Name FAN GND Power Output Ground J28 3G USB Extension Pin No. Pin Name 5V D- D+ Type Power Output Input\Out put Input\Out put Fan Power Output, 12V Ground Description Power Output, +5V D- Signal D+ Signal Signway Media Player Board SWH-5180 SPEC V2.0 12 Chapter 3 Interfaces · · · GND Ground Ground RST Output Reset Control J32 TTL Serial Port Pin No. Pin Name Type 5V 232TX3 Output UART Data Output, TTL 232RX3 Input UART Data Input, TTL GND Ground Ground 232TX1 Output UART Data Output, TTL 232RX1 Input UART Data Input, TTL Power Output Description Power Output, 5V J35 USB Extension Pin No. Pin Name 5V D- D+ GND Type Power Output Input\Out pu Input\Out pu Ground Description Power Output，5V D- Signal D+ Signal Ground J37 Reserved IO socket, function reserved Signway Media Player Board SWH-5180 SPEC V2.0 13 Chapter 3 Interfaces · Pin No. Pin Name IO9 IO8 IO4 IO6 IO3 IO5 3V3 SDA SCL Output I2C Clock, Reserved 10 GND Ground Ground 11 URX2 Input Debug Interface, Reserved 12 URT2 Output Debug Interface, Reserved Type Description J38 Type Input/Out pu Input/Out pu Input/Out pu Input/Out pu Input/Out pu Input/Out pu Input/Out pu Input/Out pu Description Reserved IO Reserved IO Reserved IO Reserved IO Reserved IO Reserved IO Reserved IO I2C Data, Reserved SPI Extension Pin No. Pin Name 5V SPI1_DO Output SPI Data Output SPI1_DI Input SPI Data Input SPI1_CSN Output SPI Chip Select SPI1_CLK Output SPI Clock GPIO GND Output NC NC Power Output Output/In put Signway Media Player Board SWH-5180 SPEC V2.0 Power Output，5V IO Port, Reserved SPI Clock Output 14 Chapter 3 Interfaces · J42 MIC Pin Pin Name Type Description MIC+ Input Microphone Input Positive Pole MIC- Input Microphone Input Negative Pole GND Ground Ground No. · J45 USB Extension Pin No. · Pin Name 5V D- D+ GND Type Power Output Input\Out put Input\Out put Ground Description Power Output，5V D- Signal D+ Signal Ground JMP1 LCD Screen Pressure Selection Interface JMP1 corresponds to the LCDVCC1 voltage selection on the CN5 socket Pin No. Pin Name 3.3V 5V 12V Type Power Output Power Output Power Output Description Power Output，3.3V Power Output，5V Power Output，12V LCDVCC1 Power Output Screen Pressure Output Signway Media Player Board SWH-5180 SPEC V2.0 15 Chapter 3 Interfaces · JMP2 EDP Screen Pressure Selection Interface JMP2 corresponds to the EDP-VCC voltage selection on the J1 socket Pin No. Pin Name 3.3V 5V 12V Type Description Power Output Power Output Power Output Power Output，3.3V Power Output，5V Power Output，12V EDP-VCC Power Output Screen Pressure Output · U8 Pin MIPI Input/Output Pin Name Type Description 5V Output 5V 5V Output 5V GND Ground Ground GND Ground Ground BL_EN Output Backlight Enable PWM Output Backlight Brightness Control LCD_EN Output Enable LCD_RST Output Reset GND Ground Ground 10 MIPI_TX_D3N Output MIPI lane3 Output 11 MIPI_TX_D3P Output MIPI lane3 Output 12 GND Ground Ground 13 MIPI_TX_D2N Output MIPI lane2 Output 14 MIPI_TX_D2P Output MIPI lane2 Output 15 GND Ground Ground 16 MIPI_TX_CLKN Output MIPI Clock Output No. Signway Media Player Board SWH-5180 SPEC V2.0 16 Chapter 3 Interfaces Pin Pin Name Type Description 17 MIPI_TX_CLKP Output MIPI Clock Output 18 GND Ground Ground 19 MIPI_TX_D1N Output MIPI lane1Output 20 MIPI_TX_D1P Output MIPI lane1Output 21 GND Ground Ground 22 MIPI_TX_D0N Output MIPI lane0Output 23 MIPI_TX_D0P Output MIPI lane0Output 24 GND Ground Ground 25 MIPI_TX/RX_D3N 26 MIPI_TX/RX_D3P 27 GND 28 MIPI_TX/RX_D2N 29 MIPI_TX/RX_D2P 30 GND 31 MIPI_TX/RX_CLKN 32 MIPI_TX/RX_CLKP 33 GND 34 MIPI_TX/RX_D1N 35 MIPI_TX/RX_D1P 36 GND 37 MIPI_TX/RX_D0N 38 MIPI_TX/RX_D0P 39 GND Ground Ground 40 MIPI_RST Output MIPI Reset 41 CIF_PDN Output IO Control, Reserved 42 CIF_CLK Output Clock Output, Reserved No. Output/Inp ut Output/Inp ut Ground Output/Inp ut Output/Inp ut Ground Output/Inp ut Output/Inp ut Ground Output/Inp ut Output/Inp ut Ground Output/Inp ut Output/Inp ut Signway Media Player Board SWH-5180 SPEC V2.0 MIPI lane3Output/Input MIPIlane3Output/Input Ground MIPI lane2Output/Input MIPI lane2Output/Input Ground MIPI Clock MIPI Clock Ground MIPI lane1Output/Input MIPI lane1Output/Input Ground MIPI lane0Output/Input MIPI lane0Output/Input 17 Chapter 3 Interfaces Pin Pin Name Type Description 43 I2C_SCL Output I2C Clock 44 I2C_SDA Input/出 I2C Data 45 GND Ground Ground 46 GND Ground Ground 47 VCC15 Output 1.5V Power 48 VCC18 Output 1.8V Power 49 AVDD28 Output Simulation 2.8V 50 VCC28 Output 2.8V Power No. · CN5 Pin LVDS Signal Output Pin Name Type Description LCDVCC1 Power Output LCD Screen Power Output, 3.3V/5V/12V(optional) GND Ground Power Ground RXO0- Output Pixel0 Negative Data (Odd) RXO0+ Output Pixel0 Positive Data (Odd) RXO1- Output Pixel1 Negative Data (Odd) 10 RXO1+ Output Pixel1 Positive Data (Odd) 11 RXO2- Output Pixel2 Negative Data (Odd) 12 RXO2+ Output Pixel2 Positive Data (Odd) GND Ground Power Ground 15 RXOC- Output Negative Sampling Clock (Odd) 16 RXOC+ Output Positive Sampling Clock (Odd) 17 RXO3- Output Pixel3 Negative Data (Odd) 18 RXO3+ Output Pixel3 Positive Data (Odd) 19 RXE0- Output Pixel0 Negative Data ( Even ) 20 RXE0+ Output Pixel0 Positive Data ( Even ) 21 RXE1- Output Pixel1 Negative Data ( Even ) No. 13 14 Signway Media Player Board SWH-5180 SPEC V2.0 18 Chapter 3 Electrical Performance Pin Pin Name Type Description 21 RXE1+ Output Pixel1 Positive Data ( Even ) 23 RXE2- Output Pixel2 Negative Data ( Even ) 24 RXE2+ Output Pixel2 Positive Data( Even ) GND Ground Power Ground 27 RXEC- Output Negative Sampling Clock ( Even ) 28 RXEC+ Output Positive Sampling Clock ( Even ) 29 RXE3- Output Pixel3 Negative Data ( Even ) 30 RXE3+ Output Pixel3 Positive Data ( Even ) GND Ground Power Ground 33 LCD_HSYNC Output Reserved 34 XN223_BLANK Output Reserved 35 LCD_VSYNC Output Reserved 36 LCD_CLK Input/出 Reserved 37 RXO4- Output Pixel2 Negative Data ( Odd ) 38 RXO4+ Output Pixel2 Positive Data (Odd ) 39 RXE4- Output Pixel2 Negative Data ( Even ) 40 RXE4- Output Pixel2 Positive Data ( Even ) No. 25 26 31 32 · J2 TF Card Slot · J9 SIM Card Slot · J41 Place on 2 jumper caps when supply single 12V power · U28 MINIPCIE slot, expandable 3G / 4G module · RJ45 LAN · HDMI_OUT 4KExternal HDMI signal Output, Max. 4K · AU_OUT Audio Sound Output · SW1 System forced upgrade button Signway Media Player Board SWH-5180 SPEC V2.0 19 Chapter 3 Interfaces · J24 Master IC USB OTG port, can be used for system upgrades; access system; external USB device · ANT5 WIFI/BT Antenna · FCAP2 When the board is powered off, Power is supplied to the RTC Real-Time Clock Signway Media Player Board SWH-5180 SPEC V2.0 20 Chapter 3 Interfaces Item Parameters Environment Electrical Performance Min Typical Max Voltage -- 12V -- Ripple -- -- -- Current -- TBD -- Relative Humidity -- -- 80% Working Temperature 0℃ -- 40℃ Storage Temperature 0℃ -- 70℃ Signway Media Player Board SWH-5180 SPEC V2.0 21
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Page Count : 23 Has XFA : No Creator : Title : Description : Subject : Creator Tool : Producer : 福昕阅读器打印机版本8.3.1.0522 Keywords : Create Date : 2018:03:20 16:00:07+08:00 Modify Date : 2018:03:20 16:01:08+08:00 Author :EXIF Metadata provided by EXIF.tools