Napco Security Technologies 765206230 GEM-KEYF, KEY- FOB TRANSMITTER User Manual GEM KEYF WI1361 08 PROG pub

Download:
Mirror Download [FCC.gov]
Document ID	655459
Application ID	IneNa3T5WcGmoV2O6yYr4g==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.09kB (226164 bits)
Date Submitted	2006-05-08 00:00:00
Date Available	2006-05-05 00:00:00
Creation Date	2006-05-01 21:26:19
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2006-05-03 11:10:34
Document Title	GEM-KEYF_WI1361.08_PROG.pub
Document Creator	PScript5.dll Version 5.2.2
Document Author:	dblock

© NAPCO 2006
tem, the control panel must be programmed to provide a
single chirp on arming and a double chirp on disarming. A
listed alarm bell or horn is to be used.
(2) Program the burglary output for all protection devices.
GEM-KEYF
Key-Fob
Transmitter
WI1361.08 5/06
GENERAL DESCRIPTION
The GEM-KEYF is a multifunction pendant/keychain transmitter compatible with Napco GEM-Series wireless systems. It
serves as an area arm/disarm device with two auxiliary functions,
and may be used as a police panic and/or auxiliary emergency
transmitter. A 3V Lithium coin cell battery (type CR2032) powers
the GEM-KEYF transmitter. A flashing LED indication signals a
low-battery warning to replace the unit.
The GEM-KEYF leaves the factory as a remote area arm/
disarm transmitter with two Auxiliary buttons, A1 and A2. Auxiliary functions are selected by programming Key Fob Transmitter
Aux 1 and Aux 2 options: Panic, Auxiliary, or Instant protection.
In addition, any of the panel's Relay Groups may be selected for
controlling garage doors, exterior lighting, or other applications
requiring external relays (RM3000 Relay Modules, optional).
Note: The Aux 1 Button and Aux 2 Button must each be held
down for approximately 2 seconds before the respective signal
will be sent. The LED will light while the unit is transmitting.
BATTERY REPLACEMENT
1. Remove keyring from the keyring loop.
2. Carefully insert the edge of a small coin in the notch located in the bottom right corner of the Key-Fob (near the
keyring loop). Open the case by gently twisting the coin.
Lift off the top cover.
3. With the bottom half of the Key-Fob facing upwards, carefully remove the circuit board.
4. On the bottom side of the circuit board, push the battery
out of its metal holder with a sharp pencil. The battery will
slide out of its holder as shown in the image below. Note
the orientation of the battery polarity, with its positive side
up, before fully removing the battery.
5. Replace with a new battery, positive (+) side up, by sliding the battery into its metal bracket. Be certain of battery
polarity before installation.
6. Reassemble the case by first placing the circuit board, battery side down, into the Key-Fob base. Place the top of
the Key-Fob (with its rubber button/gasket in place) on the
Key-Fob base and press to snap the two Key-Fob pieces
together.
7. Test the Key-Fob operation.
06022
© NAPCO
ARM
DISARM
2032
AUX. 1
AUX. 2
Insert pencil and
push battery out of
holder as shown
Battery Replacement: Top View
of Bottom Circuit Board
Factory-Supplied Functions: Arm, Disarm, Aux. 1 and Aux. 2
Low-Battery Check. The batteries are checked automatically
during any transmission. A low-battery condition will cause the
LED to come on and start pulsing for approximately 30 seconds;
a low-battery report will be sent to the receiver.
REQUIRED PROGRAMMING
The following information is required for each unit. Refer to the
instructions for the control panel and keypad in use for detailed
programming information.
• An assigned Key Fob transmitter number
• Area number(s) to which transmitter is applicable
• The 6-digit RF ID code with checksum digit printed on the
transmitter (enter all numbers and/or letters, including leading
zeros, if any)
• Aux-1 option and Aux-2 option
Note: In UL burglar alarm installations:
(1) If the GEM-KEYF is used to arm and/or disarm the sys-
BUTTON REPLACEMENT
Factory supplied auxiliary buttons can be installed to operate
other items, such as outdoor lights. Install as follows:
1. Open the Key-Fob as per the Battery Replacement instructions (above) step 1.
2. With the top cover off, lift and remove the rubber buttons
from the inside of the top
cover.
3. Replace the rubber buttons
with the secondary buttons,
(shown at right) reassembling the Key-Fob in the reverse order of disassembly.
4. Test the Key-Fob operation.
NAPCO SECURITY LIMITED WARRANTY
NAPCO SECURITY SYSTEMS, INC.
(NAPCO) warrants its products to be free
from manufacturing defects in materials
and workmanship for thirty-six months
following the date of manufacture.
NAPCO will, within said period, at its option, repair or replace any product failing
to operate correctly without charge to the original purchaser or
user.
This warranty shall not apply to any equipment, or any
part thereof, which has been repaired by others, improperly
installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any serial numbers have
been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANT ABILITY OR A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL OTHER
OBLIGATIONS OR LIABILITIES ON THE PART OF NAPCO.
Any action for breach of warranty, including but not limited
to any implied warranty of merchant ability, must be brought
within the six months following the end of the warranty period.
IN NO CASE SHALL NAPCO BE LIABLE TO ANYONE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS
CAUSED BY THE SELLER'S OWN NEGLIGENCE OR
FAULT.
In case of defect, contact the security professional who
installed and maintains your security system. In order to exercise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to
NAPCO. After repair or replacement, NAPCO assumes the
cost of returning products under warranty. NAPCO shall have
no obligation under this warranty, or otherwise, if the product
has been repaired by others, improperly installed, improperly
used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts of God, or on which any serial numbers have been altered, defaced or removed. NAPCO will not
be responsible for any dismantling, reassembly or reinstallation charges.
This warranty contains the entire warranty. It is the sole
warranty and any prior agreements or representations,
whether oral or written, are either merged herein or are ex-
pressly canceled. NAPCO neither assumes, nor authorizes
any other person purporting to act on its behalf to modify, to
change, or to assume for it, any other warranty or liability concerning its products. In no event shall NAPCO be liable for an
amount in excess of NAPCO's original selling price of the
product, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure of
the product. Seller's warranty, as herein above set forth, shall
not be enlarged, diminished or affected by and no obligation
or liability shall arise or grow out of Seller's rendering of technical advice or service in connection with Buyer's order of the
goods furnished thereunder.
NAPCO RECOMMENDS THAT THE ENTIRE SYSTEM
BE COMPLETELY TESTED WEEKLY.
Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electrical
or communications disruption, it is possible for the system to
fail to perform as expected. NAPCO does not represent that
the product/system may not be compromised or circumvented; or that the product or system will prevent any personal
injury or property loss by burglary, robbery, fire or otherwise;
nor that the product or system will in all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of burglary, robbery, fire or
otherwise but it is not insurance or a guarantee that these
events will not occur. CONSEQUENTLY, SELLER SHALL
HAVE NO LIABILITY FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE, OR OTHER LOSS BASED ON A
CLAIM THE PRODUCT FAILED TO GIVE WARNING.
Therefore, the installer should in turn advise the consumer to
take any and all precautions for his or her safety including, but
not limited to, fleeing the premises and calling police or fire
department, in order to mitigate the possibilities of harm and/
or damage.
NAPCO is not an insurer of either the property or safety of
the user's family or employees, and limits its liability for any
loss or damage including incidental or consequential damages to NAPCO's original selling price of the product regardless of the cause of such loss or damage.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation
of incidental or consequential damages, or differentiate in their
treatment of limitations of liability for ordinary or gross negligence, so the above limitations or exclusions may not apply to
you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. Caution: Changes or modifications not expressly approved by manufacturer
could void the user's authority to operate the equipment.
Napco Security Systems, Inc.
333 Bayview Avenue
Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:31c8fc9c-3c74-44f3-93b4-363f1dbe8096
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Create Date                     : 2006:05:01 21:26:19Z
Modify Date                     : 2006:05:03 11:10:34-04:00
Metadata Date                   : 2006:05:03 11:10:34-04:00
Creator Tool                    : PScript5.dll Version 5.2.2
Document ID                     : uuid:49493404-8015-4400-99dc-42af8cbc08cf
Format                          : application/pdf
Creator                         : dblock
Title                           : GEM-KEYF_WI1361.08_PROG.pub
Author                          : dblock

EXIF Metadata provided by EXIF.tools